include/configs/PMC405.h

/*
 * (C) Copyright 2001-2004
 * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
 *
 * See file CREDITS for list of people who contributed to this
 * project.
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License as
 * published by the Free Software Foundation; either version 2 of
 * the License, or (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software
 * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
 * MA 02111-1307 USA
 */

/*
 * board/config.h - configuration options, board specific
 */

#ifndef __CONFIG_H
#define __CONFIG_H

/*
 * High Level Configuration Options
 * (easy to change)
 */

#define CONFIG_405GP		1	/* This is a PPC405 CPU		*/
#define CONFIG_4xx		1	/* ...member of PPC4xx family	*/
#define CONFIG_PMC405		1	/* ...on a PMC405 board		*/

#define CONFIG_BOARD_EARLY_INIT_F 1	/* call board_early_init_f()	*/
#define CONFIG_MISC_INIT_R	1	/* call misc_init_r()		*/

#define CONFIG_SYS_CLK_FREQ	33330000 /* external frequency to pll	*/

#define CONFIG_BAUDRATE		9600
#define CONFIG_BOOTDELAY	3	/* autoboot after 3 seconds	*/

#undef	CONFIG_BOOTARGS
#undef	CONFIG_BOOTCOMMAND

#define CONFIG_PREBOOT                  /* enable preboot variable      */

#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/

#define CONFIG_NET_MULTI	1
#undef  CONFIG_HAS_ETH1

#define CONFIG_MII		1	/* MII PHY management		*/
#define CONFIG_PHY_ADDR		0	/* PHY address			*/
#define CONFIG_LXT971_NO_SLEEP  1       /* disable sleep mode in LXT971 */
#define CONFIG_RESET_PHY_R      1       /* use reset_phy() to disable phy sleep mode */

#define CONFIG_NETCONSOLE		/* include NetConsole support	*/


/*
 * BOOTP options
 */
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME


/*
 * Command line configuration.
 */
#include <config_cmd_default.h>

#define CONFIG_CMD_BSP
#define CONFIG_CMD_PCI
#define CONFIG_CMD_IRQ
#define CONFIG_CMD_ELF
#define CONFIG_CMD_DATE
#define CONFIG_CMD_JFFS2
#define CONFIG_CMD_MII
#define CONFIG_CMD_I2C
#define CONFIG_CMD_PING
#define CONFIG_CMD_UNIVERSE
#define CONFIG_CMD_EEPROM


#define CONFIG_MAC_PARTITION
#define CONFIG_DOS_PARTITION

#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/

#define CONFIG_RTC_MC146818             /* DS1685 is MC146818 compatible*/
#define CFG_RTC_REG_BASE_ADDR	 0xF0000500 /* RTC Base Address         */

#define CONFIG_SDRAM_BANK0	1	/* init onboard SDRAM bank 0	*/

/*
 * Miscellaneous configurable options
 */
#define CFG_LONGHELP			/* undef to save memory		*/
#define CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/

#undef	CFG_HUSH_PARSER			/* use "hush" command parser	*/
#ifdef	CFG_HUSH_PARSER
#define CFG_PROMPT_HUSH_PS2	"> "
#endif

#if defined(CONFIG_CMD_KGDB)
#define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
#else
#define CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
#endif
#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
#define CFG_MAXARGS	16		/* max number of command args	*/
#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/

#define CFG_DEVICE_NULLDEV	1	/* include nulldev device	*/

#define CFG_CONSOLE_INFO_QUIET	1	/* don't print console @ startup*/

#define CONFIG_AUTO_COMPLETE	1       /* add autocompletion support   */

#define CFG_MEMTEST_START	0x0400000	/* memtest works on	*/
#define CFG_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/

#undef	CFG_EXT_SERIAL_CLOCK	       /* no external serial clock used */
#define CFG_IGNORE_405_UART_ERRATA_59	/* ignore ppc405gp errata #59	*/
#define CFG_BASE_BAUD	    691200

/* The following table includes the supported baudrates */
#define CFG_BAUDRATE_TABLE	\
	{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400,     \
	 57600, 115200, 230400, 460800, 921600 }

#define CFG_LOAD_ADDR	0x100000	/* default load address */
#define CFG_EXTBDINFO	1		/* To use extended board_into (bd_t) */

#define CFG_HZ		1000		/* decrementer freq: 1 ms ticks */

#define CONFIG_LOOPW            1       /* enable loopw command         */

#define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */

#define CONFIG_VERSION_VARIABLE 1	/* include version env variable */

#define CFG_RX_ETH_BUFFER	16	/* use 16 rx buffer on 405 emac */

/*-----------------------------------------------------------------------
 * PCI stuff
 *-----------------------------------------------------------------------
 */
#define PCI_HOST_ADAPTER 0              /* configure as pci adapter     */
#define PCI_HOST_FORCE  1               /* configure as pci host        */
#define PCI_HOST_AUTO   2               /* detected via arbiter enable  */

#define CONFIG_PCI			/* include pci support	        */
#define CONFIG_PCI_HOST	PCI_HOST_AUTO   /* select pci host function     */
#define CONFIG_PCI_PNP			/* do pci plug-and-play         */
					/* resource configuration       */

#define CONFIG_PCI_SCAN_SHOW            /* print pci devices @ startup  */

#define CONFIG_PCI_CONFIG_HOST_BRIDGE 1 /* don't skip host bridge config*/

#define CONFIG_PCI_BOOTDELAY    0       /* enable pci bootdelay variable*/

#define CFG_PCI_SUBSYS_VENDORID 0x12FE  /* PCI Vendor ID: esd gmbh      */
#define CFG_PCI_SUBSYS_DEVICEID_NONMONARCH 0x0408  /* PCI Device ID: Non-Monarch */
#define CFG_PCI_SUBSYS_DEVICEID_MONARCH 0x0409     /* PCI Device ID: Monarch */
#define CFG_PCI_SUBSYS_DEVICEID pmc405_pci_subsys_deviceid()

#define CFG_PCI_CLASSCODE       0x0b20  /* PCI Class Code: Processor/PPC*/

#define CFG_PCI_PTM1LA  (bd->bi_memstart) /* point to sdram               */
#define CFG_PCI_PTM1MS  (~(bd->bi_memsize - 1) | 1) /* memsize, enable hard-wired to 1 */
#define CFG_PCI_PTM1PCI 0x00000000      /* Host: use this pci address   */
#if 1
#define CFG_PCI_PTM2LA	0xef000000	/* point to internal regs       */
#define CFG_PCI_PTM2MS  0xff000001      /* 16MB, enable                 */
#define CFG_PCI_PTM2PCI 0x00000000      /* Host: use this pci address   */
#else /* old mapping */
#define CFG_PCI_PTM2LA  0xffc00000      /* point to flash               */
#define CFG_PCI_PTM2MS  0xffc00001      /* 4MB, enable                  */
#define CFG_PCI_PTM2PCI 0x04000000      /* Host: use this pci address   */
#endif
/*-----------------------------------------------------------------------
 * Start addresses for the final memory configuration
 * (Set up by the startup code)
 * Please note that CFG_SDRAM_BASE _must_ start at 0
 */
#define CFG_SDRAM_BASE		0x00000000
#define CFG_MONITOR_BASE	0xFFFC0000
#define CFG_MONITOR_LEN		(256 * 1024)	/* Reserve 256 kB for Monitor	*/
#define CFG_MALLOC_LEN		(128 * 1024)	/* Reserve 128 kB for malloc()	*/

/*
 * For booting Linux, the board info and command line data
 * have to be in the first 8 MB of memory, since this is
 * the maximum mapped by the Linux kernel during initialization.
 */
#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */

/*-----------------------------------------------------------------------
 * FLASH organization
 */
#define CFG_FLASH_BASE		0xFE000000
#define CFG_FLASH_INCREMENT	0x01000000

#define CFG_FLASH_CFI         1       /* Flash is CFI conformant */
#define CFG_FLASH_CFI_DRIVER  1       /* Use the common driver */
#define CFG_FLASH_PROTECTION  1       /* don't use hardware protection        */
#define CFG_FLASH_USE_BUFFER_WRITE 1  /* use buffered writes (20x faster)     */
#define CFG_MAX_FLASH_BANKS   2       /* max num of flash banks */
#define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE, CFG_FLASH_BASE + CFG_FLASH_INCREMENT }
#define CFG_MAX_FLASH_SECT    128     /* max num of sects on one chip */

#define CFG_FLASH_EMPTY_INFO		/* print 'E' for empty sector on flinfo */

/*
 * JFFS2 partitions - second bank contains u-boot
 *
 */
/* No command line, one static partition, whole device */
#undef CONFIG_JFFS2_CMDLINE
#define CONFIG_JFFS2_DEV		"nor0"
#define CONFIG_JFFS2_PART_SIZE		0x01b00000
#define CONFIG_JFFS2_PART_OFFSET	0x00400000

/* mtdparts command line support */
/* Note: fake mtd_id used, no linux mtd map file */
/*
#define CONFIG_JFFS2_CMDLINE
#define MTDIDS_DEFAULT		"nor0=pmc405-0"
#define MTDPARTS_DEFAULT	"mtdparts=pmc405-0:-(jffs2)"
*/

/*-----------------------------------------------------------------------
 * Environment Variable setup
 */
#define CFG_ENV_IS_IN_EEPROM	1	/* use EEPROM for environment vars */
#define CFG_ENV_OFFSET		0x000	/* environment starts at the beginning of the EEPROM */
#define CFG_ENV_SIZE		0x800	/* 2048 bytes may be used for env vars*/
				   /* total size of a CAT24WC16 is 2048 bytes */

#define CFG_NVRAM_BASE_ADDR	0xF0000500		/* NVRAM base address	*/
#define CFG_NVRAM_SIZE		242			/* NVRAM size		*/

/*-----------------------------------------------------------------------
 * I2C EEPROM (CAT24WC16) for environment
 */
#define CONFIG_HARD_I2C			/* I2c with hardware support */
#define CFG_I2C_SPEED		400000	/* I2C speed and slave address */
#define CFG_I2C_SLAVE		0x7F

#define CFG_I2C_EEPROM_ADDR	0x50	/* EEPROM CAT28WC08		*/
#define CFG_I2C_EEPROM_ADDR_LEN 1	/* Bytes of address		*/
/* mask of address bits that overflow into the "EEPROM chip address"	*/
#define CFG_I2C_EEPROM_ADDR_OVERFLOW	0x07
#define CFG_EEPROM_PAGE_WRITE_BITS 4	/* The Catalyst CAT24WC08 has	*/
					/* 16 byte page write mode using*/
					/* last 4 bits of the address	*/
#define CFG_EEPROM_PAGE_WRITE_DELAY_MS	10   /* and takes up to 10 msec */
#define CFG_EEPROM_PAGE_WRITE_ENABLE

/*-----------------------------------------------------------------------
 * Cache Configuration
 */
#define CFG_DCACHE_SIZE		16384	/* For AMCC 405 CPUs, older 405 ppc's	*/
					/* have only 8kB, 16kB is save here	*/
#define CFG_CACHELINE_SIZE	32	/* ...			*/
#if defined(CONFIG_CMD_KGDB)
#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
#endif

/*-----------------------------------------------------------------------
 * External Bus Controller (EBC) Setup
 */
#define FLASH0_BA	0xFF000000	    /* FLASH 0 Base Address		*/
#define FLASH1_BA	0xFE000000	    /* FLASH 1 Base Address		*/
#define CAN_BA		0xF0000000	    /* CAN Base Address			*/
#define RTC_BA		0xF0000500	    /* RTC Base Address			*/
#define NVRAM_BA        0xF0200000          /* NVRAM Base Address               */

/* Memory Bank 0 (Flash Bank 0) initialization					*/
#define CFG_EBC_PB0AP	0x92015480
#define CFG_EBC_PB0CR	FLASH0_BA | 0x9A000 /* BAS=0xFF0,BS=16MB,BU=R/W,BW=16bit*/

/* Memory Bank 1 (Flash Bank 1) initialization					*/
#define CFG_EBC_PB1AP	0x92015480
#define CFG_EBC_PB1CR	FLASH1_BA | 0x9A000 /* BAS=0xFE0,BS=16MB,BU=R/W,BW=16bit*/

/* Memory Bank 2 (CAN0, 1, RTC) initialization					*/
#define CFG_EBC_PB2AP	0x03000440   /* TWT=5,TH=2,CSN=0,OEN=0,WBN=0,WBF=0      */
#define CFG_EBC_PB2CR	CAN_BA | 0x18000    /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit	*/

/* Memory Bank 3 -> unused */

/* Memory Bank 4 (NVRAM) initialization					*/
#define CFG_EBC_PB4AP	0x03000440   /* TWT=5,TH=2,CSN=0,OEN=0,WBN=0,WBF=0      */
#define CFG_EBC_PB4CR	NVRAM_BA | 0x18000    /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit	*/

/*-----------------------------------------------------------------------
 * FPGA stuff
 */
#define CFG_FPGA_XC95XL		1	    /* using Xilinx XC95XL CPLD	     */
#define CFG_FPGA_MAX_SIZE	32*1024	    /* 32kByte is enough for CPLD    */

/* FPGA program pin configuration */
#define CFG_FPGA_PRG		0x04000000  /* JTAG TMS pin (ppc output)     */
#define CFG_FPGA_CLK		0x02000000  /* JTAG TCK pin (ppc output)     */
#define CFG_FPGA_DATA		0x01000000  /* JTAG TDO->TDI data pin (ppc output) */
#define CFG_FPGA_INIT		0x00010000  /* unused (ppc input)	     */
#define CFG_FPGA_DONE		0x00008000  /* JTAG TDI->TDO pin (ppc input) */

#define CFG_VXWORKS_MAC_PTR	0x00000000	/* Pass Ethernet MAC to VxWorks */

/*-----------------------------------------------------------------------
 * GPIOs
 */
#define CFG_NONMONARCH		(0x80000000 >> 14)   /* GPIO24 */
#define CFG_XEREADY		(0x80000000 >> 15)   /* GPIO15 */
#define CFG_INTA_FAKE		(0x80000000 >> 19)   /* GPIO19 */
#define CFG_SELF_RST		(0x80000000 >> 21)   /* GPIO21 */
#define CFG_REV1_2		(0x80000000 >> 23)   /* GPIO23 */

/*-----------------------------------------------------------------------
 * Definitions for initial stack pointer and data area (in data cache)
 */

/* use on chip memory ( OCM ) for temperary stack until sdram is tested */
#define CFG_TEMP_STACK_OCM	1

/* On Chip Memory location */
#define CFG_OCM_DATA_ADDR	0xF8000000
#define CFG_OCM_DATA_SIZE	0x1000

#define CFG_INIT_RAM_ADDR	CFG_OCM_DATA_ADDR /* inside of SDRAM		*/
#define CFG_INIT_RAM_END	CFG_OCM_DATA_SIZE /* End of used area in RAM	*/
#define CFG_GBL_DATA_SIZE      128  /* size in bytes reserved for initial data */
#define CFG_GBL_DATA_OFFSET    (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET

/*
 * Internal Definitions
 *
 * Boot Flags
 */
#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
#define BOOTFLAG_WARM	0x02		/* Software reboot			*/

#endif	/* __CONFIG_H */