blob: 7e62aef07e19e8fe330daa818b8c998ec430b3fe [file] [log] [blame]
Akshay Bhatf9162b12016-01-29 15:16:40 -05001/*
2 * Copyright 2015 Timesys Corporation
3 * Copyright 2015 General Electric Company
4 * Copyright 2012 Freescale Semiconductor, Inc.
5 *
6 * SPDX-License-Identifier: GPL-2.0+
7 */
8
9#include <asm/arch/clock.h>
10#include <asm/arch/imx-regs.h>
11#include <asm/arch/iomux.h>
12#include <asm/arch/mx6-pins.h>
Masahiro Yamada1221ce42016-09-21 11:28:55 +090013#include <linux/errno.h>
Akshay Bhatf9162b12016-01-29 15:16:40 -050014#include <asm/gpio.h>
15#include <asm/imx-common/mxc_i2c.h>
16#include <asm/imx-common/iomux-v3.h>
17#include <asm/imx-common/boot_mode.h>
18#include <asm/imx-common/video.h>
19#include <mmc.h>
20#include <fsl_esdhc.h>
21#include <miiphy.h>
22#include <netdev.h>
23#include <asm/arch/mxc_hdmi.h>
24#include <asm/arch/crm_regs.h>
25#include <asm/io.h>
26#include <asm/arch/sys_proto.h>
27#include <i2c.h>
Akshay Bhat54971ac2016-04-12 18:13:59 -040028#include <pwm.h>
Akshay Bhatf9162b12016-01-29 15:16:40 -050029DECLARE_GLOBAL_DATA_PTR;
30
Justin Waters7d0b8cf2016-04-13 17:03:18 -040031#define NC_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
32 PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \
33 PAD_CTL_HYS)
34
Akshay Bhatf9162b12016-01-29 15:16:40 -050035#define UART_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
36 PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \
37 PAD_CTL_SRE_FAST | PAD_CTL_HYS)
38
39#define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP | \
40 PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm | \
41 PAD_CTL_SRE_FAST | PAD_CTL_HYS)
42
43#define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_PUE | \
44 PAD_CTL_SPEED_HIGH | PAD_CTL_DSE_48ohm | PAD_CTL_SRE_FAST)
45
46#define ENET_CLK_PAD_CTRL (PAD_CTL_SPEED_MED | \
47 PAD_CTL_DSE_120ohm | PAD_CTL_SRE_FAST)
48
49#define ENET_RX_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
50 PAD_CTL_SPEED_HIGH | PAD_CTL_SRE_FAST)
51
52#define SPI_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_SPEED_MED | \
53 PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
54
55#define I2C_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
56 PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \
57 PAD_CTL_ODE | PAD_CTL_SRE_FAST)
58
59#define I2C_PAD MUX_PAD_CTRL(I2C_PAD_CTRL)
60
61int dram_init(void)
62{
Fabio Estevamc6a51ba2016-07-23 13:23:40 -030063 gd->ram_size = imx_ddr_size();
Akshay Bhatf9162b12016-01-29 15:16:40 -050064
65 return 0;
66}
67
68static iomux_v3_cfg_t const uart3_pads[] = {
69 MX6_PAD_EIM_D31__UART3_RTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
70 MX6_PAD_EIM_D23__UART3_CTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
71 MX6_PAD_EIM_D24__UART3_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
72 MX6_PAD_EIM_D25__UART3_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
73};
74
75static iomux_v3_cfg_t const uart4_pads[] = {
76 MX6_PAD_KEY_COL0__UART4_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
77 MX6_PAD_KEY_ROW0__UART4_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
78};
79
80static iomux_v3_cfg_t const enet_pads[] = {
81 MX6_PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
82 MX6_PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
83 MX6_PAD_RGMII_TXC__RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
84 MX6_PAD_RGMII_TD0__RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
85 MX6_PAD_RGMII_TD1__RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
86 MX6_PAD_RGMII_TD2__RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
87 MX6_PAD_RGMII_TD3__RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
88 MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
89 MX6_PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_CLK_PAD_CTRL),
90 MX6_PAD_RGMII_RXC__RGMII_RXC | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
91 MX6_PAD_RGMII_RD0__RGMII_RD0 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
92 MX6_PAD_RGMII_RD1__RGMII_RD1 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
93 MX6_PAD_RGMII_RD2__RGMII_RD2 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
94 MX6_PAD_RGMII_RD3__RGMII_RD3 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
95 MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
96 /* AR8033 PHY Reset */
97 MX6_PAD_ENET_TX_EN__GPIO1_IO28 | MUX_PAD_CTRL(NO_PAD_CTRL),
98};
99
100static void setup_iomux_enet(void)
101{
102 imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads));
103
104 /* Reset AR8033 PHY */
105 gpio_direction_output(IMX_GPIO_NR(1, 28), 0);
106 udelay(500);
107 gpio_set_value(IMX_GPIO_NR(1, 28), 1);
108}
109
110static iomux_v3_cfg_t const usdhc2_pads[] = {
111 MX6_PAD_SD2_CLK__SD2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
112 MX6_PAD_SD2_CMD__SD2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
113 MX6_PAD_SD2_DAT0__SD2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
114 MX6_PAD_SD2_DAT1__SD2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
115 MX6_PAD_SD2_DAT2__SD2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
116 MX6_PAD_SD2_DAT3__SD2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
117 MX6_PAD_GPIO_4__GPIO1_IO04 | MUX_PAD_CTRL(NO_PAD_CTRL),
118};
119
120static iomux_v3_cfg_t const usdhc3_pads[] = {
121 MX6_PAD_SD3_CLK__SD3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
122 MX6_PAD_SD3_CMD__SD3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
123 MX6_PAD_SD3_RST__SD3_RESET | MUX_PAD_CTRL(USDHC_PAD_CTRL),
124 MX6_PAD_SD3_DAT0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
125 MX6_PAD_SD3_DAT1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
126 MX6_PAD_SD3_DAT2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
127 MX6_PAD_SD3_DAT3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
128 MX6_PAD_SD3_DAT4__SD3_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
129 MX6_PAD_SD3_DAT5__SD3_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
130 MX6_PAD_SD3_DAT6__SD3_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
131 MX6_PAD_SD3_DAT7__SD3_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
132};
133
134static iomux_v3_cfg_t const usdhc4_pads[] = {
135 MX6_PAD_SD4_CLK__SD4_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
136 MX6_PAD_SD4_CMD__SD4_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
137 MX6_PAD_SD4_DAT0__SD4_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
138 MX6_PAD_SD4_DAT1__SD4_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
139 MX6_PAD_SD4_DAT2__SD4_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
140 MX6_PAD_SD4_DAT3__SD4_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
141 MX6_PAD_SD4_DAT4__SD4_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
142 MX6_PAD_SD4_DAT5__SD4_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
143 MX6_PAD_SD4_DAT6__SD4_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
144 MX6_PAD_SD4_DAT7__SD4_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
145 MX6_PAD_NANDF_CS0__GPIO6_IO11 | MUX_PAD_CTRL(NO_PAD_CTRL),
146 MX6_PAD_NANDF_CS1__GPIO6_IO14 | MUX_PAD_CTRL(NO_PAD_CTRL),
147};
148
149static iomux_v3_cfg_t const ecspi1_pads[] = {
150 MX6_PAD_EIM_D16__ECSPI1_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL),
151 MX6_PAD_EIM_D17__ECSPI1_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL),
152 MX6_PAD_EIM_D18__ECSPI1_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL),
153 MX6_PAD_EIM_EB2__GPIO2_IO30 | MUX_PAD_CTRL(NO_PAD_CTRL),
154};
155
156static struct i2c_pads_info i2c_pad_info1 = {
157 .scl = {
158 .i2c_mode = MX6_PAD_CSI0_DAT9__I2C1_SCL | I2C_PAD,
159 .gpio_mode = MX6_PAD_CSI0_DAT9__GPIO5_IO27 | I2C_PAD,
160 .gp = IMX_GPIO_NR(5, 27)
161 },
162 .sda = {
163 .i2c_mode = MX6_PAD_CSI0_DAT8__I2C1_SDA | I2C_PAD,
164 .gpio_mode = MX6_PAD_CSI0_DAT8__GPIO5_IO26 | I2C_PAD,
165 .gp = IMX_GPIO_NR(5, 26)
166 }
167};
168
169static struct i2c_pads_info i2c_pad_info2 = {
170 .scl = {
171 .i2c_mode = MX6_PAD_KEY_COL3__I2C2_SCL | I2C_PAD,
172 .gpio_mode = MX6_PAD_KEY_COL3__GPIO4_IO12 | I2C_PAD,
173 .gp = IMX_GPIO_NR(4, 12)
174 },
175 .sda = {
176 .i2c_mode = MX6_PAD_KEY_ROW3__I2C2_SDA | I2C_PAD,
177 .gpio_mode = MX6_PAD_KEY_ROW3__GPIO4_IO13 | I2C_PAD,
178 .gp = IMX_GPIO_NR(4, 13)
179 }
180};
181
182static struct i2c_pads_info i2c_pad_info3 = {
183 .scl = {
184 .i2c_mode = MX6_PAD_GPIO_3__I2C3_SCL | I2C_PAD,
185 .gpio_mode = MX6_PAD_GPIO_3__GPIO1_IO03 | I2C_PAD,
186 .gp = IMX_GPIO_NR(1, 3)
187 },
188 .sda = {
189 .i2c_mode = MX6_PAD_GPIO_6__I2C3_SDA | I2C_PAD,
190 .gpio_mode = MX6_PAD_GPIO_6__GPIO1_IO06 | I2C_PAD,
191 .gp = IMX_GPIO_NR(1, 6)
192 }
193};
194
195#ifdef CONFIG_MXC_SPI
196int board_spi_cs_gpio(unsigned bus, unsigned cs)
197{
198 return (bus == 0 && cs == 0) ? (IMX_GPIO_NR(2, 30)) : -1;
199}
200
201static void setup_spi(void)
202{
203 imx_iomux_v3_setup_multiple_pads(ecspi1_pads, ARRAY_SIZE(ecspi1_pads));
204}
205#endif
206
207static iomux_v3_cfg_t const pcie_pads[] = {
208 MX6_PAD_GPIO_5__GPIO1_IO05 | MUX_PAD_CTRL(NO_PAD_CTRL),
209 MX6_PAD_GPIO_17__GPIO7_IO12 | MUX_PAD_CTRL(NO_PAD_CTRL),
210};
211
212static void setup_pcie(void)
213{
214 imx_iomux_v3_setup_multiple_pads(pcie_pads, ARRAY_SIZE(pcie_pads));
215}
216
217static void setup_iomux_uart(void)
218{
219 imx_iomux_v3_setup_multiple_pads(uart3_pads, ARRAY_SIZE(uart3_pads));
220 imx_iomux_v3_setup_multiple_pads(uart4_pads, ARRAY_SIZE(uart4_pads));
221}
222
223#ifdef CONFIG_FSL_ESDHC
224struct fsl_esdhc_cfg usdhc_cfg[3] = {
225 {USDHC2_BASE_ADDR},
226 {USDHC3_BASE_ADDR},
227 {USDHC4_BASE_ADDR},
228};
229
230#define USDHC2_CD_GPIO IMX_GPIO_NR(1, 4)
231#define USDHC4_CD_GPIO IMX_GPIO_NR(6, 11)
232
233int board_mmc_getcd(struct mmc *mmc)
234{
235 struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
236 int ret = 0;
237
238 switch (cfg->esdhc_base) {
239 case USDHC2_BASE_ADDR:
240 ret = !gpio_get_value(USDHC2_CD_GPIO);
241 break;
242 case USDHC3_BASE_ADDR:
243 ret = 1; /* eMMC is always present */
244 break;
245 case USDHC4_BASE_ADDR:
246 ret = !gpio_get_value(USDHC4_CD_GPIO);
247 break;
248 }
249
250 return ret;
251}
252
253int board_mmc_init(bd_t *bis)
254{
255 int ret;
256 int i;
257
258 for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
259 switch (i) {
260 case 0:
261 imx_iomux_v3_setup_multiple_pads(
262 usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
263 gpio_direction_input(USDHC2_CD_GPIO);
264 usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
265 break;
266 case 1:
267 imx_iomux_v3_setup_multiple_pads(
268 usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
269 usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
270 break;
271 case 2:
272 imx_iomux_v3_setup_multiple_pads(
273 usdhc4_pads, ARRAY_SIZE(usdhc4_pads));
274 gpio_direction_input(USDHC4_CD_GPIO);
275 usdhc_cfg[2].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
276 break;
277 default:
278 printf("Warning: you configured more USDHC controllers\n"
279 "(%d) then supported by the board (%d)\n",
280 i + 1, CONFIG_SYS_FSL_USDHC_NUM);
281 return -EINVAL;
282 }
283
284 ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
285 if (ret)
286 return ret;
287 }
288
289 return 0;
290}
291#endif
292
293static int mx6_rgmii_rework(struct phy_device *phydev)
294{
295 /* Configure AR8033 to ouput a 125MHz clk from CLK_25M */
296 /* set device address 0x7 */
297 phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x7);
298 /* offset 0x8016: CLK_25M Clock Select */
299 phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x8016);
300 /* enable register write, no post increment, address 0x7 */
301 phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x4007);
302 /* set to 125 MHz from local PLL source */
303 phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x18);
304
305 /* rgmii tx clock delay enable */
306 /* set debug port address: SerDes Test and System Mode Control */
307 phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x05);
308 /* enable rgmii tx clock delay */
309 phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x100);
310
311 return 0;
312}
313
314int board_phy_config(struct phy_device *phydev)
315{
316 mx6_rgmii_rework(phydev);
317
318 if (phydev->drv->config)
319 phydev->drv->config(phydev);
320
321 return 0;
322}
323
324#if defined(CONFIG_VIDEO_IPUV3)
325static iomux_v3_cfg_t const backlight_pads[] = {
326 /* Power for LVDS Display */
327 MX6_PAD_EIM_D22__GPIO3_IO22 | MUX_PAD_CTRL(NO_PAD_CTRL),
328#define LVDS_POWER_GP IMX_GPIO_NR(3, 22)
329 /* Backlight enable for LVDS display */
330 MX6_PAD_GPIO_0__GPIO1_IO00 | MUX_PAD_CTRL(NO_PAD_CTRL),
331#define LVDS_BACKLIGHT_GP IMX_GPIO_NR(1, 0)
Akshay Bhat54971ac2016-04-12 18:13:59 -0400332 /* backlight PWM brightness control */
333 MX6_PAD_SD1_DAT3__PWM1_OUT | MUX_PAD_CTRL(NO_PAD_CTRL),
Akshay Bhatf9162b12016-01-29 15:16:40 -0500334};
335
336static void do_enable_hdmi(struct display_info_t const *dev)
337{
338 imx_enable_hdmi_phy();
339}
340
341int board_cfb_skip(void)
342{
343 gpio_direction_output(LVDS_POWER_GP, 1);
344
345 return 0;
346}
347
348static int detect_baseboard(struct display_info_t const *dev)
349{
350 if (IS_ENABLED(CONFIG_TARGET_GE_B450V3) ||
351 IS_ENABLED(CONFIG_TARGET_GE_B650V3))
352 return 1;
353
354 return 0;
355}
356
357struct display_info_t const displays[] = {{
358 .bus = -1,
359 .addr = -1,
360 .pixfmt = IPU_PIX_FMT_RGB24,
361 .detect = detect_baseboard,
362 .enable = NULL,
363 .mode = {
364 .name = "G121X1-L03",
365 .refresh = 60,
366 .xres = 1024,
367 .yres = 768,
368 .pixclock = 15385,
369 .left_margin = 20,
370 .right_margin = 300,
371 .upper_margin = 30,
372 .lower_margin = 8,
373 .hsync_len = 1,
374 .vsync_len = 1,
375 .sync = FB_SYNC_EXT,
376 .vmode = FB_VMODE_NONINTERLACED
377} }, {
378 .bus = -1,
379 .addr = 3,
380 .pixfmt = IPU_PIX_FMT_RGB24,
381 .detect = detect_hdmi,
382 .enable = do_enable_hdmi,
383 .mode = {
384 .name = "HDMI",
385 .refresh = 60,
386 .xres = 1024,
387 .yres = 768,
388 .pixclock = 15385,
389 .left_margin = 220,
390 .right_margin = 40,
391 .upper_margin = 21,
392 .lower_margin = 7,
393 .hsync_len = 60,
394 .vsync_len = 10,
395 .sync = FB_SYNC_EXT,
396 .vmode = FB_VMODE_NONINTERLACED
397} } };
398size_t display_count = ARRAY_SIZE(displays);
399
Akshay Bhat494d43e2016-04-12 18:13:58 -0400400static void enable_videopll(void)
401{
402 struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
403 s32 timeout = 100000;
404
405 setbits_le32(&ccm->analog_pll_video, BM_ANADIG_PLL_VIDEO_POWERDOWN);
406
407 /* set video pll to 910MHz (24MHz * (37+11/12))
408 * video pll post div to 910/4 = 227.5MHz
409 */
410 clrsetbits_le32(&ccm->analog_pll_video,
411 BM_ANADIG_PLL_VIDEO_DIV_SELECT |
412 BM_ANADIG_PLL_VIDEO_POST_DIV_SELECT,
413 BF_ANADIG_PLL_VIDEO_DIV_SELECT(37) |
414 BF_ANADIG_PLL_VIDEO_POST_DIV_SELECT(0));
415
416 writel(BF_ANADIG_PLL_VIDEO_NUM_A(11), &ccm->analog_pll_video_num);
417 writel(BF_ANADIG_PLL_VIDEO_DENOM_B(12), &ccm->analog_pll_video_denom);
418
419 clrbits_le32(&ccm->analog_pll_video, BM_ANADIG_PLL_VIDEO_POWERDOWN);
420
421 while (timeout--)
422 if (readl(&ccm->analog_pll_video) & BM_ANADIG_PLL_VIDEO_LOCK)
423 break;
424
425 if (timeout < 0)
426 printf("Warning: video pll lock timeout!\n");
427
428 clrsetbits_le32(&ccm->analog_pll_video,
429 BM_ANADIG_PLL_VIDEO_BYPASS,
430 BM_ANADIG_PLL_VIDEO_ENABLE);
431}
432
Akshay Bhatde708da2016-04-12 18:13:57 -0400433static void setup_display_b850v3(void)
Akshay Bhatf9162b12016-01-29 15:16:40 -0500434{
435 struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
436 struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
Akshay Bhatf9162b12016-01-29 15:16:40 -0500437
Akshay Bhat494d43e2016-04-12 18:13:58 -0400438 enable_videopll();
439
Akshay Bhatde708da2016-04-12 18:13:57 -0400440 /* IPU1 D0 clock is 227.5 / 3.5 = 65MHz */
441 clrbits_le32(&mxc_ccm->cscmr2, MXC_CCM_CSCMR2_LDB_DI0_IPU_DIV);
442
Akshay Bhatf9162b12016-01-29 15:16:40 -0500443 imx_setup_hdmi();
444
Akshay Bhatde708da2016-04-12 18:13:57 -0400445 /* Set LDB_DI0 as clock source for IPU_DI0 */
446 clrsetbits_le32(&mxc_ccm->chsccdr,
447 MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_MASK,
448 (CHSCCDR_CLK_SEL_LDB_DI0 <<
449 MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET));
Akshay Bhatf9162b12016-01-29 15:16:40 -0500450
Akshay Bhatde708da2016-04-12 18:13:57 -0400451 /* Turn on IPU LDB DI0 clocks */
452 setbits_le32(&mxc_ccm->CCGR3, MXC_CCM_CCGR3_LDB_DI0_MASK);
Akshay Bhatf9162b12016-01-29 15:16:40 -0500453
Akshay Bhatde708da2016-04-12 18:13:57 -0400454 enable_ipu_clock();
Akshay Bhatf9162b12016-01-29 15:16:40 -0500455
Akshay Bhatde708da2016-04-12 18:13:57 -0400456 writel(IOMUXC_GPR2_BGREF_RRMODE_EXTERNAL_RES |
457 IOMUXC_GPR2_DI1_VS_POLARITY_ACTIVE_LOW |
458 IOMUXC_GPR2_DI0_VS_POLARITY_ACTIVE_LOW |
459 IOMUXC_GPR2_BIT_MAPPING_CH1_SPWG |
460 IOMUXC_GPR2_DATA_WIDTH_CH1_24BIT |
461 IOMUXC_GPR2_BIT_MAPPING_CH0_SPWG |
462 IOMUXC_GPR2_DATA_WIDTH_CH0_24BIT |
463 IOMUXC_GPR2_SPLIT_MODE_EN_MASK |
464 IOMUXC_GPR2_LVDS_CH0_MODE_ENABLED_DI0 |
465 IOMUXC_GPR2_LVDS_CH1_MODE_ENABLED_DI0,
466 &iomux->gpr[2]);
Akshay Bhatf9162b12016-01-29 15:16:40 -0500467
Akshay Bhatde708da2016-04-12 18:13:57 -0400468 clrbits_le32(&iomux->gpr[3],
469 IOMUXC_GPR3_LVDS0_MUX_CTL_MASK |
470 IOMUXC_GPR3_LVDS1_MUX_CTL_MASK |
471 IOMUXC_GPR3_HDMI_MUX_CTL_MASK);
472}
Akshay Bhatf9162b12016-01-29 15:16:40 -0500473
Akshay Bhatde708da2016-04-12 18:13:57 -0400474static void setup_display_bx50v3(void)
475{
476 struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
477 struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
478
Akshay Bhat8d293f42016-04-12 18:14:00 -0400479 /* When a reset/reboot is performed the display power needs to be turned
480 * off for atleast 500ms. The boot time is ~300ms, we need to wait for
481 * an additional 200ms here. Unfortunately we use external PMIC for
482 * doing the reset, so can not differentiate between POR vs soft reset
483 */
484 mdelay(200);
485
Akshay Bhatde708da2016-04-12 18:13:57 -0400486 /* IPU1 DI0 clock is 480/7 = 68.5 MHz */
487 setbits_le32(&mxc_ccm->cscmr2, MXC_CCM_CSCMR2_LDB_DI0_IPU_DIV);
488
489 /* Set LDB_DI0 as clock source for IPU_DI0 */
490 clrsetbits_le32(&mxc_ccm->chsccdr,
491 MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_MASK,
492 (CHSCCDR_CLK_SEL_LDB_DI0 <<
493 MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET));
494
495 /* Turn on IPU LDB DI0 clocks */
496 setbits_le32(&mxc_ccm->CCGR3, MXC_CCM_CCGR3_LDB_DI0_MASK);
497
498 enable_ipu_clock();
499
500 writel(IOMUXC_GPR2_BGREF_RRMODE_EXTERNAL_RES |
501 IOMUXC_GPR2_DI0_VS_POLARITY_ACTIVE_LOW |
502 IOMUXC_GPR2_BIT_MAPPING_CH0_SPWG |
503 IOMUXC_GPR2_DATA_WIDTH_CH0_24BIT |
504 IOMUXC_GPR2_LVDS_CH0_MODE_ENABLED_DI0,
505 &iomux->gpr[2]);
506
507 clrsetbits_le32(&iomux->gpr[3],
508 IOMUXC_GPR3_LVDS0_MUX_CTL_MASK,
509 (IOMUXC_GPR3_MUX_SRC_IPU1_DI0 <<
510 IOMUXC_GPR3_LVDS0_MUX_CTL_OFFSET));
Akshay Bhatf9162b12016-01-29 15:16:40 -0500511
512 /* backlights off until needed */
513 imx_iomux_v3_setup_multiple_pads(backlight_pads,
514 ARRAY_SIZE(backlight_pads));
515 gpio_direction_input(LVDS_POWER_GP);
516 gpio_direction_input(LVDS_BACKLIGHT_GP);
517}
518#endif /* CONFIG_VIDEO_IPUV3 */
519
520/*
521 * Do not overwrite the console
522 * Use always serial for U-Boot console
523 */
524int overwrite_console(void)
525{
526 return 1;
527}
528
529int board_eth_init(bd_t *bis)
530{
531 setup_iomux_enet();
532 setup_pcie();
533
534 return cpu_eth_init(bis);
535}
536
537static iomux_v3_cfg_t const misc_pads[] = {
538 MX6_PAD_KEY_ROW2__GPIO4_IO11 | MUX_PAD_CTRL(NO_PAD_CTRL),
Justin Waters7d0b8cf2016-04-13 17:03:18 -0400539 MX6_PAD_EIM_A25__GPIO5_IO02 | MUX_PAD_CTRL(NC_PAD_CTRL),
540 MX6_PAD_EIM_CS0__GPIO2_IO23 | MUX_PAD_CTRL(NC_PAD_CTRL),
541 MX6_PAD_EIM_CS1__GPIO2_IO24 | MUX_PAD_CTRL(NC_PAD_CTRL),
542 MX6_PAD_EIM_OE__GPIO2_IO25 | MUX_PAD_CTRL(NC_PAD_CTRL),
543 MX6_PAD_EIM_BCLK__GPIO6_IO31 | MUX_PAD_CTRL(NC_PAD_CTRL),
544 MX6_PAD_GPIO_1__GPIO1_IO01 | MUX_PAD_CTRL(NC_PAD_CTRL),
Akshay Bhatf9162b12016-01-29 15:16:40 -0500545};
546#define SUS_S3_OUT IMX_GPIO_NR(4, 11)
547#define WIFI_EN IMX_GPIO_NR(6, 14)
548
549int board_early_init_f(void)
550{
551 imx_iomux_v3_setup_multiple_pads(misc_pads,
552 ARRAY_SIZE(misc_pads));
553
554 setup_iomux_uart();
555
Akshay Bhat494d43e2016-04-12 18:13:58 -0400556#if defined(CONFIG_VIDEO_IPUV3)
557 if (IS_ENABLED(CONFIG_TARGET_GE_B850V3))
558 /* Set LDB clock to Video PLL */
559 select_ldb_di_clock_source(MXC_PLL5_CLK);
560 else
561 /* Set LDB clock to USB PLL */
562 select_ldb_di_clock_source(MXC_PLL3_SW_CLK);
563#endif
Akshay Bhatf9162b12016-01-29 15:16:40 -0500564 return 0;
565}
566
567int board_init(void)
568{
569 gpio_direction_output(SUS_S3_OUT, 1);
570 gpio_direction_output(WIFI_EN, 1);
571#if defined(CONFIG_VIDEO_IPUV3)
Akshay Bhatde708da2016-04-12 18:13:57 -0400572 if (IS_ENABLED(CONFIG_TARGET_GE_B850V3))
573 setup_display_b850v3();
574 else
575 setup_display_bx50v3();
Akshay Bhatf9162b12016-01-29 15:16:40 -0500576#endif
577 /* address of boot parameters */
578 gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
579
580#ifdef CONFIG_MXC_SPI
581 setup_spi();
582#endif
583 setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
584 setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2);
585 setup_i2c(3, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info3);
586
587 return 0;
588}
589
590#ifdef CONFIG_CMD_BMODE
591static const struct boot_mode board_boot_modes[] = {
592 /* 4 bit bus width */
593 {"sd2", MAKE_CFGVAL(0x40, 0x28, 0x00, 0x00)},
594 {"sd3", MAKE_CFGVAL(0x40, 0x30, 0x00, 0x00)},
595 {NULL, 0},
596};
597#endif
598
599int board_late_init(void)
600{
601#ifdef CONFIG_CMD_BMODE
602 add_board_boot_modes(board_boot_modes);
603#endif
Andrew Shadura0c344e62016-05-24 15:56:17 +0200604
605#ifdef CONFIG_VIDEO_IPUV3
Akshay Bhatf9162b12016-01-29 15:16:40 -0500606 /* We need at least 200ms between power on and backlight on
607 * as per specifications from CHI MEI */
608 mdelay(250);
609
Akshay Bhat54971ac2016-04-12 18:13:59 -0400610 /* enable backlight PWM 1 */
611 pwm_init(0, 0, 0);
612
613 /* duty cycle 5000000ns, period: 5000000ns */
614 pwm_config(0, 5000000, 5000000);
615
Akshay Bhatf9162b12016-01-29 15:16:40 -0500616 /* Backlight Power */
617 gpio_direction_output(LVDS_BACKLIGHT_GP, 1);
618
Akshay Bhat54971ac2016-04-12 18:13:59 -0400619 pwm_enable(0);
Andrew Shadura0c344e62016-05-24 15:56:17 +0200620#endif
Akshay Bhat54971ac2016-04-12 18:13:59 -0400621
Akshay Bhatf9162b12016-01-29 15:16:40 -0500622 return 0;
623}
624
625int checkboard(void)
626{
627 printf("BOARD: %s\n", CONFIG_BOARD_NAME);
628 return 0;
629}