include/configs/M5282EVB.h - github/trini/u-boot - Gitiles

 /*
  * Configuation settings for the Motorola MC5282EVB board.
  *
  * (C) Copyright 2003 Josef Baumgartner <josef.baumgartner@telex.de>
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */

 /*
  * board/config.h - configuration options, board specific
  */

 #ifndef _CONFIG_M5282EVB_H
 #define _CONFIG_M5282EVB_H

 /*
  * High Level Configuration Options
  * (easy to change)
  */
 #define CONFIG_MCFTMR

 #define CONFIG_MCFUART
 #define CONFIG_SYS_UART_PORT		(0)
 #define CONFIG_BAUDRATE		115200

 #undef	CONFIG_MONITOR_IS_IN_RAM	/* define if monitor is started from a pre-loader */

 /* Configuration for environment
  * Environment is embedded in u-boot in the second sector of the flash
  */
 #define CONFIG_ENV_ADDR		0xffe04000
 #define CONFIG_ENV_SIZE		0x2000
 #define CONFIG_ENV_IS_IN_FLASH	1

 #define LDS_BOARD_TEXT \
 	. = DEFINED(env_offset) ? env_offset : .; \
 	common/env_embedded.o (.text*);

 /*
  * BOOTP options
  */
 #define CONFIG_BOOTP_BOOTFILESIZE
 #define CONFIG_BOOTP_BOOTPATH
 #define CONFIG_BOOTP_GATEWAY
 #define CONFIG_BOOTP_HOSTNAME

 /*
  * Command line configuration.
  */
 #include <config_cmd_default.h>
 #define CONFIG_CMD_CACHE
 #define CONFIG_CMD_NET
 #define CONFIG_CMD_PING
 #define CONFIG_CMD_MII

 #undef CONFIG_CMD_LOADS
 #undef CONFIG_CMD_LOADB

 #define CONFIG_MCFFEC
 #ifdef CONFIG_MCFFEC
 #	define CONFIG_MII		1
 #	define CONFIG_MII_INIT		1
 #	define CONFIG_SYS_DISCOVER_PHY
 #	define CONFIG_SYS_RX_ETH_BUFFER	8
 #	define CONFIG_SYS_FAULT_ECHO_LINK_DOWN

 #	define CONFIG_SYS_FEC0_PINMUX		0
 #	define CONFIG_SYS_FEC0_MIIBASE		CONFIG_SYS_FEC0_IOBASE
 #	define MCFFEC_TOUT_LOOP		50000
 /* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */
 #	ifndef CONFIG_SYS_DISCOVER_PHY
 #		define FECDUPLEX	FULL
 #		define FECSPEED		_100BASET
 #	else
 #		ifndef CONFIG_SYS_FAULT_ECHO_LINK_DOWN
 #			define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
 #		endif
 #	endif			/* CONFIG_SYS_DISCOVER_PHY */
 #endif

 #define CONFIG_BOOTDELAY	5
 #ifdef CONFIG_MCFFEC
 #	define CONFIG_IPADDR	192.162.1.2
 #	define CONFIG_NETMASK	255.255.255.0
 #	define CONFIG_SERVERIP	192.162.1.1
 #	define CONFIG_GATEWAYIP	192.162.1.1
 #endif				/* CONFIG_MCFFEC */

 #define CONFIG_HOSTNAME		M5282EVB
 #define CONFIG_EXTRA_ENV_SETTINGS		\
 	"netdev=eth0\0"				\
 	"loadaddr=10000\0"			\
 	"u-boot=u-boot.bin\0"			\
 	"load=tftp ${loadaddr) ${u-boot}\0"	\
 	"upd=run load; run prog\0"		\
 	"prog=prot off ffe00000 ffe3ffff;"	\
 	"era ffe00000 ffe3ffff;"		\
 	"cp.b ${loadaddr} ffe00000 ${filesize};"\
 	"save\0"				\
 	""

 #define CONFIG_SYS_PROMPT		"-> "
 #define	CONFIG_SYS_LONGHELP		/* undef to save memory         */

 #if defined(CONFIG_CMD_KGDB)
 #define	CONFIG_SYS_CBSIZE		1024	/* Console I/O Buffer Size      */
 #else
 #define	CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size      */
 #endif
 #define	CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)	/* Print Buffer Size */
 #define	CONFIG_SYS_MAXARGS		16	/* max number of command args   */
 #define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size    */

 #define CONFIG_SYS_LOAD_ADDR		0x20000

 #define CONFIG_SYS_MEMTEST_START	0x400
 #define CONFIG_SYS_MEMTEST_END		0x380000

 #define	CONFIG_SYS_CLK			64000000

 /* PLL Configuration: Ext Clock * 6 (see table 9-4 of MCF user manual) */

 #define CONFIG_SYS_MFD			0x02	/* PLL Multiplication Factor Devider */
 #define CONFIG_SYS_RFD			0x00	/* PLL Reduce Frecuency Devider */

 /*
  * Low Level Configuration Settings
  * (address mappings, register initial values, etc.)
  * You should know what you are doing if you make changes here.
  */
 #define	CONFIG_SYS_MBAR		0x40000000

 /*-----------------------------------------------------------------------
  * Definitions for initial stack pointer and data area (in DPRAM)
  */
 #define CONFIG_SYS_INIT_RAM_ADDR	0x20000000
 #define CONFIG_SYS_INIT_RAM_SIZE	0x10000	/* Size of used area in internal SRAM    */
 #define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET

 /*-----------------------------------------------------------------------
  * Start addresses for the final memory configuration
  * (Set up by the startup code)
  * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
  */
 #define CONFIG_SYS_SDRAM_BASE		0x00000000
 #define	CONFIG_SYS_SDRAM_SIZE		16	/* SDRAM size in MB */
 #define CONFIG_SYS_FLASH_BASE		CONFIG_SYS_CS0_BASE
 #define	CONFIG_SYS_INT_FLASH_BASE	0xf0000000
 #define CONFIG_SYS_INT_FLASH_ENABLE	0x21

 /* If M5282 port is fully implemented the monitor base will be behind
  * the vector table. */
 #if (CONFIG_SYS_TEXT_BASE != CONFIG_SYS_INT_FLASH_BASE)
 #define CONFIG_SYS_MONITOR_BASE	(CONFIG_SYS_FLASH_BASE + 0x400)
 #else
 #define CONFIG_SYS_MONITOR_BASE	(CONFIG_SYS_TEXT_BASE + 0x418)	/* 24 Byte for CFM-Config */
 #endif

 #define CONFIG_SYS_MONITOR_LEN		0x20000
 #define CONFIG_SYS_MALLOC_LEN		(256 << 10)
 #define CONFIG_SYS_BOOTPARAMS_LEN	64*1024

 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 8 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization ??
  */
 #define CONFIG_SYS_BOOTMAPSZ		(CONFIG_SYS_SDRAM_BASE + (CONFIG_SYS_SDRAM_SIZE << 20))

 /*-----------------------------------------------------------------------
  * FLASH organization
  */
 #define CONFIG_SYS_FLASH_CFI
 #ifdef CONFIG_SYS_FLASH_CFI

 #	define CONFIG_FLASH_CFI_DRIVER	1
 #	define CONFIG_SYS_FLASH_SIZE		0x1000000	/* Max size that the board might have */
 #	define CONFIG_SYS_FLASH_CFI_WIDTH	FLASH_CFI_16BIT
 #	define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks */
 #	define CONFIG_SYS_MAX_FLASH_SECT	137	/* max number of sectors on one chip */
 #	define CONFIG_SYS_FLASH_PROTECTION	/* "Real" (hardware) sectors protection */
 #	define CONFIG_SYS_FLASH_CHECKSUM
 #	define CONFIG_SYS_FLASH_BANKS_LIST	{ CONFIG_SYS_FLASH_BASE }
 #endif

 /*-----------------------------------------------------------------------
  * Cache Configuration
  */
 #define CONFIG_SYS_CACHELINE_SIZE	16

 #define ICACHE_STATUS			(CONFIG_SYS_INIT_RAM_ADDR + \
 					 CONFIG_SYS_INIT_RAM_SIZE - 8)
 #define DCACHE_STATUS			(CONFIG_SYS_INIT_RAM_ADDR + \
 					 CONFIG_SYS_INIT_RAM_SIZE - 4)
 #define CONFIG_SYS_ICACHE_INV		(CF_CACR_CINV + CF_CACR_DCM)
 #define CONFIG_SYS_CACHE_ACR0		(CONFIG_SYS_SDRAM_BASE | \
 					 CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \
 					 CF_ACR_EN | CF_ACR_SM_ALL)
 #define CONFIG_SYS_CACHE_ICACR		(CF_CACR_CENB | CF_CACR_DISD | \
 					 CF_CACR_CEIB | CF_CACR_DBWE | \
 					 CF_CACR_EUSP)

 /*-----------------------------------------------------------------------
  * Memory bank definitions
  */
 #define CONFIG_SYS_CS0_BASE		0xFFE00000
 #define CONFIG_SYS_CS0_CTRL		0x00001980
 #define CONFIG_SYS_CS0_MASK		0x001F0001

 /*-----------------------------------------------------------------------
  * Port configuration
  */
 #define CONFIG_SYS_PACNT		0x0000000	/* Port A D[31:24] */
 #define CONFIG_SYS_PADDR		0x0000000
 #define CONFIG_SYS_PADAT		0x0000000

 #define CONFIG_SYS_PBCNT		0x0000000	/* Port B D[23:16] */
 #define CONFIG_SYS_PBDDR		0x0000000
 #define CONFIG_SYS_PBDAT		0x0000000

 #define CONFIG_SYS_PCCNT		0x0000000	/* Port C D[15:08] */
 #define CONFIG_SYS_PCDDR		0x0000000
 #define CONFIG_SYS_PCDAT		0x0000000

 #define CONFIG_SYS_PDCNT		0x0000000	/* Port D D[07:00] */
 #define CONFIG_SYS_PCDDR		0x0000000
 #define CONFIG_SYS_PCDAT		0x0000000

 #define CONFIG_SYS_PEHLPAR		0xC0
 #define CONFIG_SYS_PUAPAR		0x0F	/* UA0..UA3 = Uart 0 +1 */
 #define CONFIG_SYS_DDRUA		0x05
 #define CONFIG_SYS_PJPAR		0xFF

 #endif				/* _CONFIG_M5282EVB_H */
	/*
	* Configuation settings for the Motorola MC5282EVB board.
	*
	* (C) Copyright 2003 Josef Baumgartner <josef.baumgartner@telex.de>
	*
	* SPDX-License-Identifier: GPL-2.0+
	*/

	/*
	* board/config.h - configuration options, board specific
	*/

	#ifndef _CONFIG_M5282EVB_H
	#define _CONFIG_M5282EVB_H

	/*
	* High Level Configuration Options
	* (easy to change)
	*/
	#define CONFIG_MCFTMR

	#define CONFIG_MCFUART
	#define CONFIG_SYS_UART_PORT (0)
	#define CONFIG_BAUDRATE 115200

	#undef CONFIG_MONITOR_IS_IN_RAM /* define if monitor is started from a pre-loader */

	/* Configuration for environment
	* Environment is embedded in u-boot in the second sector of the flash
	*/
	#define CONFIG_ENV_ADDR 0xffe04000
	#define CONFIG_ENV_SIZE 0x2000
	#define CONFIG_ENV_IS_IN_FLASH 1

	#define LDS_BOARD_TEXT \
	. = DEFINED(env_offset) ? env_offset : .; \
	common/env_embedded.o (.text*);

	/*
	* BOOTP options
	*/
	#define CONFIG_BOOTP_BOOTFILESIZE
	#define CONFIG_BOOTP_BOOTPATH
	#define CONFIG_BOOTP_GATEWAY
	#define CONFIG_BOOTP_HOSTNAME

	/*
	* Command line configuration.
	*/
	#include <config_cmd_default.h>
	#define CONFIG_CMD_CACHE
	#define CONFIG_CMD_NET
	#define CONFIG_CMD_PING
	#define CONFIG_CMD_MII

	#undef CONFIG_CMD_LOADS
	#undef CONFIG_CMD_LOADB

	#define CONFIG_MCFFEC
	#ifdef CONFIG_MCFFEC
	# define CONFIG_MII 1
	# define CONFIG_MII_INIT 1
	# define CONFIG_SYS_DISCOVER_PHY
	# define CONFIG_SYS_RX_ETH_BUFFER 8
	# define CONFIG_SYS_FAULT_ECHO_LINK_DOWN

	# define CONFIG_SYS_FEC0_PINMUX 0
	# define CONFIG_SYS_FEC0_MIIBASE CONFIG_SYS_FEC0_IOBASE
	# define MCFFEC_TOUT_LOOP 50000
	/* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */
	# ifndef CONFIG_SYS_DISCOVER_PHY
	# define FECDUPLEX FULL
	# define FECSPEED _100BASET
	# else
	# ifndef CONFIG_SYS_FAULT_ECHO_LINK_DOWN
	# define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
	# endif
	# endif /* CONFIG_SYS_DISCOVER_PHY */
	#endif

	#define CONFIG_BOOTDELAY 5
	#ifdef CONFIG_MCFFEC
	# define CONFIG_IPADDR 192.162.1.2
	# define CONFIG_NETMASK 255.255.255.0
	# define CONFIG_SERVERIP 192.162.1.1
	# define CONFIG_GATEWAYIP 192.162.1.1
	#endif /* CONFIG_MCFFEC */

	#define CONFIG_HOSTNAME M5282EVB
	#define CONFIG_EXTRA_ENV_SETTINGS \
	"netdev=eth0\0" \
	"loadaddr=10000\0" \
	"u-boot=u-boot.bin\0" \
	"load=tftp ${loadaddr) ${u-boot}\0" \
	"upd=run load; run prog\0" \
	"prog=prot off ffe00000 ffe3ffff;" \
	"era ffe00000 ffe3ffff;" \
	"cp.b ${loadaddr} ffe00000 ${filesize};"\
	"save\0" \
	""

	#define CONFIG_SYS_PROMPT "-> "
	#define CONFIG_SYS_LONGHELP /* undef to save memory */

	#if defined(CONFIG_CMD_KGDB)
	#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
	#else
	#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
	#endif
	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
	#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */

	#define CONFIG_SYS_LOAD_ADDR 0x20000

	#define CONFIG_SYS_MEMTEST_START 0x400
	#define CONFIG_SYS_MEMTEST_END 0x380000

	#define CONFIG_SYS_CLK 64000000

	/* PLL Configuration: Ext Clock * 6 (see table 9-4 of MCF user manual) */

	#define CONFIG_SYS_MFD 0x02 /* PLL Multiplication Factor Devider */
	#define CONFIG_SYS_RFD 0x00 /* PLL Reduce Frecuency Devider */

	/*
	* Low Level Configuration Settings
	* (address mappings, register initial values, etc.)
	* You should know what you are doing if you make changes here.
	*/
	#define CONFIG_SYS_MBAR 0x40000000

	/*-----------------------------------------------------------------------
	* Definitions for initial stack pointer and data area (in DPRAM)
	*/
	#define CONFIG_SYS_INIT_RAM_ADDR 0x20000000
	#define CONFIG_SYS_INIT_RAM_SIZE 0x10000 /* Size of used area in internal SRAM */
	#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
	#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET

	/*-----------------------------------------------------------------------
	* Start addresses for the final memory configuration
	* (Set up by the startup code)
	* Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
	*/
	#define CONFIG_SYS_SDRAM_BASE 0x00000000
	#define CONFIG_SYS_SDRAM_SIZE 16 /* SDRAM size in MB */
	#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_CS0_BASE
	#define CONFIG_SYS_INT_FLASH_BASE 0xf0000000
	#define CONFIG_SYS_INT_FLASH_ENABLE 0x21

	/* If M5282 port is fully implemented the monitor base will be behind
	* the vector table. */
	#if (CONFIG_SYS_TEXT_BASE != CONFIG_SYS_INT_FLASH_BASE)
	#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400)
	#else
	#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_TEXT_BASE + 0x418) /* 24 Byte for CFM-Config */
	#endif

	#define CONFIG_SYS_MONITOR_LEN 0x20000
	#define CONFIG_SYS_MALLOC_LEN (256 << 10)
	#define CONFIG_SYS_BOOTPARAMS_LEN 64*1024

	/*
	* For booting Linux, the board info and command line data
	* have to be in the first 8 MB of memory, since this is
	* the maximum mapped by the Linux kernel during initialization ??
	*/
	#define CONFIG_SYS_BOOTMAPSZ (CONFIG_SYS_SDRAM_BASE + (CONFIG_SYS_SDRAM_SIZE << 20))

	/*-----------------------------------------------------------------------
	* FLASH organization
	*/
	#define CONFIG_SYS_FLASH_CFI
	#ifdef CONFIG_SYS_FLASH_CFI

	# define CONFIG_FLASH_CFI_DRIVER 1
	# define CONFIG_SYS_FLASH_SIZE 0x1000000 /* Max size that the board might have */
	# define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
	# define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
	# define CONFIG_SYS_MAX_FLASH_SECT 137 /* max number of sectors on one chip */
	# define CONFIG_SYS_FLASH_PROTECTION /* "Real" (hardware) sectors protection */
	# define CONFIG_SYS_FLASH_CHECKSUM
	# define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
	#endif

	/*-----------------------------------------------------------------------
	* Cache Configuration
	*/
	#define CONFIG_SYS_CACHELINE_SIZE 16

	#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \
	CONFIG_SYS_INIT_RAM_SIZE - 8)
	#define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \
	CONFIG_SYS_INIT_RAM_SIZE - 4)
	#define CONFIG_SYS_ICACHE_INV (CF_CACR_CINV + CF_CACR_DCM)
	#define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_SDRAM_BASE \| \
	CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) \| \
	CF_ACR_EN \| CF_ACR_SM_ALL)
	#define CONFIG_SYS_CACHE_ICACR (CF_CACR_CENB \| CF_CACR_DISD \| \
	CF_CACR_CEIB \| CF_CACR_DBWE \| \
	CF_CACR_EUSP)

	/*-----------------------------------------------------------------------
	* Memory bank definitions
	*/
	#define CONFIG_SYS_CS0_BASE 0xFFE00000
	#define CONFIG_SYS_CS0_CTRL 0x00001980
	#define CONFIG_SYS_CS0_MASK 0x001F0001

	/*-----------------------------------------------------------------------
	* Port configuration
	*/
	#define CONFIG_SYS_PACNT 0x0000000 /* Port A D[31:24] */
	#define CONFIG_SYS_PADDR 0x0000000
	#define CONFIG_SYS_PADAT 0x0000000

	#define CONFIG_SYS_PBCNT 0x0000000 /* Port B D[23:16] */
	#define CONFIG_SYS_PBDDR 0x0000000
	#define CONFIG_SYS_PBDAT 0x0000000

	#define CONFIG_SYS_PCCNT 0x0000000 /* Port C D[15:08] */
	#define CONFIG_SYS_PCDDR 0x0000000
	#define CONFIG_SYS_PCDAT 0x0000000

	#define CONFIG_SYS_PDCNT 0x0000000 /* Port D D[07:00] */
	#define CONFIG_SYS_PCDDR 0x0000000
	#define CONFIG_SYS_PCDAT 0x0000000

	#define CONFIG_SYS_PEHLPAR 0xC0
	#define CONFIG_SYS_PUAPAR 0x0F /* UA0..UA3 = Uart 0 +1 */
	#define CONFIG_SYS_DDRUA 0x05
	#define CONFIG_SYS_PJPAR 0xFF

	#endif /* _CONFIG_M5282EVB_H */