| /* |
| * (C) Copyright 2004 |
| * DAVE Srl |
| * |
| * http://www.dave-tech.it |
| * http://www.wawnet.biz |
| * mailto:info@wawnet.biz |
| * |
| * Configuation settings for the B2 board. |
| * |
| * See file CREDITS for list of people who contributed to this |
| * project. |
| * |
| * This program is free software; you can redistribute it and/or |
| * modify it under the terms of the GNU General Public License as |
| * published by the Free Software Foundation; either version 2 of |
| * the License, or (at your option) any later version. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 59 Temple Place, Suite 330, Boston, |
| * MA 02111-1307 USA |
| */ |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| /* |
| * High Level Configuration Options |
| * (easy to change) |
| */ |
| #define CONFIG_ARM7 1 /* This is a ARM7 CPU */ |
| #define CONFIG_B2 1 /* on an B2 Board */ |
| #define CONFIG_ARM_THUMB 1 /* this is an ARM7TDMI */ |
| #undef CONFIG_ARM7_REVD /* disable ARM720 REV.D Workarounds */ |
| |
| #define CONFIG_S3C44B0_CLOCK_SPEED 75 /* we have a 75Mhz S3C44B0*/ |
| |
| |
| #undef CONFIG_USE_IRQ /* don't need them anymore */ |
| |
| |
| /* |
| * Size of malloc() pool |
| */ |
| #define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */ |
| #define CONFIG_ENV_SIZE 1024 /* 1024 bytes may be used for env vars*/ |
| #define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024 ) |
| #define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ |
| |
| /* |
| * Hardware drivers |
| */ |
| #define CONFIG_DRIVER_LAN91C96 |
| #define CONFIG_LAN91C96_BASE 0x04000300 /* base address */ |
| #define CONFIG_SMC_USE_32_BIT |
| #undef CONFIG_SHOW_ACTIVITY |
| #define CONFIG_NET_RETRY_COUNT 10 /* # of retries */ |
| |
| /* |
| * select serial console configuration |
| */ |
| #define CONFIG_S3C44B0_SERIAL |
| #define CONFIG_SERIAL1 1 /* we use Serial line 1 */ |
| |
| #define CONFIG_S3C44B0_I2C |
| #define CONFIG_RTC_S3C44B0 |
| |
| /* allow to overwrite serial and ethaddr */ |
| #define CONFIG_ENV_OVERWRITE |
| |
| #define CONFIG_BAUDRATE 115200 |
| |
| /* |
| * BOOTP options |
| */ |
| #define CONFIG_BOOTP_SUBNETMASK |
| #define CONFIG_BOOTP_GATEWAY |
| #define CONFIG_BOOTP_HOSTNAME |
| #define CONFIG_BOOTP_BOOTPATH |
| #define CONFIG_BOOTP_BOOTFILESIZE |
| |
| |
| /* |
| * Command line configuration. |
| */ |
| #include <config_cmd_default.h> |
| |
| #define CONFIG_CMD_DATE |
| #define CONFIG_CMD_ELF |
| #define CONFIG_CMD_EEPROM |
| #define CONFIG_CMD_I2C |
| |
| |
| #define CONFIG_BOOTDELAY 5 |
| #define CONFIG_ETHADDR 00:50:c2:1e:af:fb |
| #define CONFIG_BOOTARGS "setenv bootargs root=/dev/ram ip=192.168.0.70:::::eth0:off \ |
| ether=25,0,0,0,eth0 ethaddr=00:50:c2:1e:af:fb" |
| #define CONFIG_NETMASK 255.255.0.0 |
| #define CONFIG_IPADDR 192.168.0.70 |
| #define CONFIG_SERVERIP 192.168.0.23 |
| #define CONFIG_BOOTFILE "B2-rootfs/usr/B2-zImage.u-boot" |
| #define CONFIG_BOOTCOMMAND "bootm 20000 f0000" |
| |
| /* |
| * Miscellaneous configurable options |
| */ |
| #define CONFIG_SYS_LONGHELP /* undef to save memory */ |
| #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ |
| #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ |
| #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ |
| #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ |
| #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ |
| |
| #define CONFIG_SYS_MEMTEST_START 0x0C400000 /* memtest works on */ |
| #define CONFIG_SYS_MEMTEST_END 0x0C800000 /* 4 ... 8 MB in DRAM */ |
| |
| #define CONFIG_SYS_LOAD_ADDR 0x0c700000 /* default load address */ |
| |
| #define CONFIG_SYS_HZ 1000 /* 1 kHz */ |
| |
| /* valid baudrates */ |
| #define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } |
| |
| /*----------------------------------------------------------------------- |
| * Stack sizes |
| * |
| * The stack sizes are set up in start.S using the settings below |
| */ |
| #define CONFIG_STACKSIZE (128*1024) /* regular stack */ |
| #ifdef CONFIG_USE_IRQ |
| #define CONFIG_STACKSIZE_IRQ (4*1024) /* IRQ stack */ |
| #define CONFIG_STACKSIZE_FIQ (4*1024) /* FIQ stack */ |
| #endif |
| |
| /*----------------------------------------------------------------------- |
| * Physical Memory Map |
| */ |
| #define CONFIG_NR_DRAM_BANKS 1 /* we have 1 banks of DRAM */ |
| #define PHYS_SDRAM_1 0xc0000000 /* SDRAM Bank #1 */ |
| #define PHYS_SDRAM_1_SIZE 0x01000000 /* 16 MB */ |
| |
| #define PHYS_FLASH_1 0x00000000 /* Flash Bank #1 */ |
| #define PHYS_FLASH_SIZE 0x00400000 /* 4 MB */ |
| |
| #define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1 |
| |
| /*----------------------------------------------------------------------- |
| * FLASH and environment organization |
| */ |
| /*----------------------------------------------------------------------- |
| * FLASH organization |
| */ |
| #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ |
| #define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */ |
| |
| #define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ |
| #define CONFIG_SYS_FLASH_WRITE_TOUT 1000 /* Timeout for Flash Write (in ms) */ |
| |
| #define CONFIG_SYS_FLASH_WORD_SIZE unsigned short /* flash word size (width) */ |
| #define CONFIG_SYS_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */ |
| #define CONFIG_SYS_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */ |
| /* |
| * The following defines are added for buggy IOP480 byte interface. |
| * All other boards should use the standard values (CPCI405 etc.) |
| */ |
| #define CONFIG_SYS_FLASH_READ0 0x0000 /* 0 is standard */ |
| #define CONFIG_SYS_FLASH_READ1 0x0001 /* 1 is standard */ |
| #define CONFIG_SYS_FLASH_READ2 0x0002 /* 2 is standard */ |
| |
| #define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ |
| |
| /*----------------------------------------------------------------------- |
| * Environment Variable setup |
| */ |
| #define CONFIG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */ |
| #define CONFIG_ENV_OFFSET 0x0 /* environment starts at the beginning of the EEPROM */ |
| |
| /*----------------------------------------------------------------------- |
| * I2C EEPROM (STM24C02W6) for environment |
| */ |
| #define CONFIG_HARD_I2C /* I2c with hardware support */ |
| #define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ |
| #define CONFIG_SYS_I2C_SLAVE 0xFE |
| |
| #define CONFIG_SYS_I2C_EEPROM_ADDR 0xA8 /* EEPROM STM24C02W6 */ |
| #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ |
| /* mask of address bits that overflow into the "EEPROM chip address" */ |
| /*#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07*/ |
| #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */ |
| /* 16 byte page write mode using*/ |
| /* last 4 bits of the address */ |
| #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ |
| |
| /* Flash banks JFFS2 should use */ |
| /* |
| #define CONFIG_SYS_JFFS2_FIRST_BANK 0 |
| #define CONFIG_SYS_JFFS2_FIRST_SECTOR 2 |
| #define CONFIG_SYS_JFFS2_NUM_BANKS 1 |
| */ |
| |
| /* |
| Linux TAGs (see lib_arm/armlinux.c) |
| */ |
| #define CONFIG_CMDLINE_TAG |
| #undef CONFIG_SETUP_MEMORY_TAGS |
| #define CONFIG_INITRD_TAG |
| |
| #endif /* __CONFIG_H */ |