| This file contains information for VSC9953, a Vitesse L2 Switch IP |
| which is integrated in the T1040/T1020 Freescale SoCs. |
| |
| About Device: |
| ============= |
| VSC9953 is an 8-port Gigabit Ethernet switch supports the following features: |
| - 8192 MAC addresses |
| - Static Address provisioning |
| - Dynamic learning of MAC addresses and aging |
| - 4096 VLANs |
| - Independent and shared VLAN learning (IVL, SVL) |
| - Policing with storm control and MC/BC protection |
| - IPv4 and IPv6 multicast |
| - Jumbo frames (9.6 KB) |
| - Access Control List |
| - VLAN editing, translation and remarking |
| - RMON counters per port |
| |
| Switch interfaces: |
| - 8 Gigabit switch ports (ports 0 to 7) are external and are connected to external PHYs |
| - 2 switch ports (ports 8 and 9) of 2.5 G are connected (fixed links) |
| to FMan ports (FM1@DTSEC1 and FM1@DTSEC2) |
| |
| Commands Overview: |
| ============= |
| Commands supported |
| - enable/disable a port or show its configuration (speed, duplexity, status, etc.) |
| - port statistics |
| - MAC learning |
| - add/remove FDB entries |
| - Port-based VLAN |
| - Private/Shared VLAN learning |
| - VLAN ingress filtering |
| |
| Commands syntax |
| ethsw [port <port_no>] { enable | disable | show } - enable/disable a port; show a port's configuration |
| ethsw [port <port_no>] statistics { [help] | [clear] } - show an l2 switch port's statistics |
| ethsw [port <port_no>] learning { [help] | show | auto | disable } - enable/disable/show learning configuration on a port |
| ethsw [port <port_no>] [vlan <vid>] fdb { [help] | show | flush | { add | del } <mac> } - add/delete a mac entry in FDB; use show to see FDB entries; |
| if [vlan <vid>] is missing, VID 1 will be used |
| ethsw [port <port_no>] pvid { [help] | show | <pvid> } - set/show PVID (ingress and egress VLAN tagging) for a port |
| ethsw [port <port_no>] vlan { [help] | show | add <vid> | del <vid> } - add a VLAN to a port (VLAN members) |
| ethsw [port <port_no>] untagged { [help] | show | all | none | pvid } - set egress tagging mode for a port |
| ethsw [port <port_no>] egress tag { [help] | show | pvid | classified } - configure VID source for egress tag. |
| Tag's VID could be the frame's classified VID or the PVID of the port |
| ethsw vlan fdb { [help] | show | shared | private } - make VLAN learning shared or private |
| ethsw [port <port_no>] ingress filtering { [help] | show | enable | disable } - enable/disable VLAN ingress filtering on port |
| |
| => ethsw show |
| Port Status Link Speed Duplex |
| 0 enabled down 10 half |
| 1 enabled down 10 half |
| 2 enabled down 10 half |
| 3 enabled up 1000 full |
| 4 disabled down - half |
| 5 disabled down - half |
| 6 disabled down - half |
| 7 disabled down - half |
| 8 enabled up 2500 full |
| 9 enabled up 2500 full |
| => |