| Jan Kundrát | ba4309e | 2020-04-29 01:32:38 +0200 | [diff] [blame^] | 1 | # enable 1GB of RAM, not just 750 MB |
| 2 | CONFIG_HIGHMEM=y | ||||
| 3 | |||||
| Jan Kundrát | 7bcb063 | 2017-09-29 17:12:30 +0200 | [diff] [blame] | 4 | # this is a part of the Clearfog Base carrier |
| Jan Kundrát | 420a6d8 | 2017-09-29 16:56:31 +0200 | [diff] [blame] | 5 | CONFIG_SENSORS_MCP3021=y |
| Jan Kundrát | 7bcb063 | 2017-09-29 17:12:30 +0200 | [diff] [blame] | 6 | |
| Jan Kundrát | c1f337f | 2017-11-14 18:53:32 +0100 | [diff] [blame] | 7 | # mvneta |
| 8 | CONFIG_MVNETA_BM_ENABLE=y | ||||
| 9 | CONFIG_MVPP2=n | ||||
| 10 | |||||
| Jan Kundrát | 133638c | 2017-11-14 19:40:53 +0100 | [diff] [blame] | 11 | # Clearfog: enable interrupt signalling for the expander0 |
| 12 | CONFIG_GPIO_PCA953X_IRQ=y | ||||
| 13 | |||||
| Jan Kundrát | 7bcb063 | 2017-09-29 17:12:30 +0200 | [diff] [blame] | 14 | # PMBus for the PSUs |
| 15 | CONFIG_PMBUS=y | ||||
| 16 | CONFIG_SENSORS_PMBUS=y | ||||
| Jan Kundrát | 28658c9 | 2017-11-13 19:32:04 +0100 | [diff] [blame] | 17 | |
| 18 | # SPI-to-Quad-UART | ||||
| 19 | CONFIG_SERIAL_MAX310X=y | ||||
| Jan Kundrát | 7f2ff83 | 2018-01-23 19:21:56 +0100 | [diff] [blame] | 20 | |
| 21 | # Extra I2C bus for the PSUs | ||||
| 22 | CONFIG_I2C_GPIO=y | ||||
| Jan Kundrát | 4e36c34 | 2018-01-25 16:29:24 +0100 | [diff] [blame] | 23 | |
| 24 | # SPI GPIO expander | ||||
| 25 | CONFIG_PINCTRL_MCP23S08=y | ||||
| Jan Kundrát | f007ca1 | 2018-02-08 14:19:35 +0100 | [diff] [blame] | 26 | |
| Jan Kundrát | 8f3357f | 2018-08-08 14:16:32 +0200 | [diff] [blame] | 27 | CONFIG_LEDS_TLC591XX=y |
| 28 | |||||
| Jan Kundrát | f007ca1 | 2018-02-08 14:19:35 +0100 | [diff] [blame] | 29 | # For the Lumentum OCM |
| 30 | CONFIG_SPI_SPIDEV=y | ||||
| Jan Kundrát | 540849c | 2018-06-28 18:16:41 +0200 | [diff] [blame] | 31 | |
| 32 | CONFIG_SFP=y | ||||
| Jan Kundrát | 6c684c5 | 2018-10-01 16:40:04 +0200 | [diff] [blame] | 33 | CONFIG_IGB=y |
| Jan Kundrát | 59865d4 | 2018-06-30 22:53:18 +0200 | [diff] [blame] | 34 | |
| Jan Kundrát | eb7e538 | 2019-04-17 12:04:26 +0200 | [diff] [blame] | 35 | # optoswitch PCB |
| 36 | CONFIG_IIO=y | ||||
| 37 | CONFIG_AD5593R=y | ||||
| 38 | |||||
| Jan Kundrát | 59865d4 | 2018-06-30 22:53:18 +0200 | [diff] [blame] | 39 | CONFIG_MACH_ARMADA_370=n |
| 40 | CONFIG_MACH_ARMADA_375=n | ||||
| 41 | CONFIG_MACH_ARMADA_39X=n | ||||
| 42 | CONFIG_MACH_ARMADA_XP=n | ||||
| 43 | CONFIG_MACH_DOVE=n | ||||
| 44 | CONFIG_NR_CPUS=2 | ||||
| 45 | CONFIG_HIGHMEM=n | ||||
| 46 | CONFIG_MV643XX_ETH=n | ||||
| 47 | CONFIG_KEYBOARD_ATKBD=N | ||||
| 48 | CONFIG_INPUT_MOUSE=N | ||||
| Jan Kundrát | 47d6b8b | 2019-03-07 11:04:36 +0100 | [diff] [blame] | 49 | |
| Jan Kundrát | f97c81d | 2020-02-06 00:33:19 +0100 | [diff] [blame] | 50 | CONFIG_LOCALVERSION="-cla-cfb" |