| Masahiro Yamada | da333ae | 2014-10-23 22:26:09 +0900 | [diff] [blame] | 1 | config DM |
| 2 | bool "Enable Driver Model" |
| Masahiro Yamada | da333ae | 2014-10-23 22:26:09 +0900 | [diff] [blame] | 3 | help |
| Simon Glass | f94a1be | 2015-02-05 21:41:35 -0700 | [diff] [blame] | 4 | This config option enables Driver Model. This brings in the core |
| 5 | support, including scanning of platform data on start-up. If |
| 6 | CONFIG_OF_CONTROL is enabled, the device tree will be scanned also |
| 7 | when available. |
| Simon Glass | 91a91ff | 2015-02-05 21:41:36 -0700 | [diff] [blame] | 8 | |
| 9 | config SPL_DM |
| 10 | bool "Enable Driver Model for SPL" |
| 11 | depends on DM && SPL |
| 12 | help |
| 13 | Enable driver model in SPL. You will need to provide a |
| 14 | suitable malloc() implementation. If you are not using the |
| 15 | full malloc() enabled by CONFIG_SYS_SPL_MALLOC_START, |
| 16 | consider using CONFIG_SYS_MALLOC_SIMPLE. In that case you |
| 17 | must provide CONFIG_SYS_MALLOC_F_LEN to set the size. |
| 18 | In most cases driver model will only allocate a few uclasses |
| 19 | and devices in SPL, so 1KB should be enable. See |
| 20 | CONFIG_SYS_MALLOC_F_LEN for more details on how to enable it. |
| 21 | |
| 22 | config DM_WARN |
| 23 | bool "Enable warnings in driver model" |
| Masahiro Yamada | d648964 | 2015-02-24 22:26:21 +0900 | [diff] [blame] | 24 | depends on DM |
| 25 | default y |
| Simon Glass | 91a91ff | 2015-02-05 21:41:36 -0700 | [diff] [blame] | 26 | help |
| 27 | The dm_warn() function can use up quite a bit of space for its |
| 28 | strings. By default this is disabled for SPL builds to save space. |
| 29 | This will cause dm_warn() to be compiled out - it will do nothing |
| 30 | when called. |
| Simon Glass | 91a91ff | 2015-02-05 21:41:36 -0700 | [diff] [blame] | 31 | |
| 32 | config DM_DEVICE_REMOVE |
| 33 | bool "Support device removal" |
| Masahiro Yamada | d648964 | 2015-02-24 22:26:21 +0900 | [diff] [blame] | 34 | depends on DM |
| 35 | default y |
| Simon Glass | 91a91ff | 2015-02-05 21:41:36 -0700 | [diff] [blame] | 36 | help |
| 37 | We can save some code space by dropping support for removing a |
| 38 | device. This is not normally required in SPL, so by default this |
| 39 | option is disabled for SPL. |
| Simon Glass | 91a91ff | 2015-02-05 21:41:36 -0700 | [diff] [blame] | 40 | |
| 41 | config DM_STDIO |
| 42 | bool "Support stdio registration" |
| Masahiro Yamada | d648964 | 2015-02-24 22:26:21 +0900 | [diff] [blame] | 43 | depends on DM |
| 44 | default y |
| Simon Glass | 91a91ff | 2015-02-05 21:41:36 -0700 | [diff] [blame] | 45 | help |
| 46 | Normally serial drivers register with stdio so that they can be used |
| 47 | as normal output devices. In SPL we don't normally use stdio, so |
| 48 | we can omit this feature. |