Sandeep Paulraj | 5df65cf | 2009-10-10 13:37:10 -0400 | [diff] [blame] | 1 | /* |
| 2 | * Copyright (C) 2009 Texas Instruments Incorporated |
| 3 | * |
Wolfgang Denk | 1a45966 | 2013-07-08 09:37:19 +0200 | [diff] [blame] | 4 | * SPDX-License-Identifier: GPL-2.0+ |
Sandeep Paulraj | 5df65cf | 2009-10-10 13:37:10 -0400 | [diff] [blame] | 5 | */ |
| 6 | |
| 7 | #include <common.h> |
| 8 | #include <nand.h> |
| 9 | #include <asm/io.h> |
| 10 | #include <asm/arch/hardware.h> |
Laurence Withers | 0bf98f1 | 2011-07-18 09:25:58 -0400 | [diff] [blame] | 11 | #include <asm/arch/gpio.h> |
Khoronzhuk, Ivan | 3e01ed0 | 2014-06-07 04:22:52 +0300 | [diff] [blame] | 12 | #include <asm/ti-common/davinci_nand.h> |
Sughosh Ganu | d7f9b50 | 2010-11-28 20:21:27 -0500 | [diff] [blame] | 13 | #include <asm/arch/davinci_misc.h> |
Sandeep Paulraj | 5df65cf | 2009-10-10 13:37:10 -0400 | [diff] [blame] | 14 | #include <net.h> |
| 15 | #include <netdev.h> |
| 16 | |
| 17 | DECLARE_GLOBAL_DATA_PTR; |
| 18 | |
| 19 | int board_init(void) |
| 20 | { |
| 21 | struct davinci_gpio *gpio01_base = |
| 22 | (struct davinci_gpio *)DAVINCI_GPIO_BANK01; |
| 23 | struct davinci_gpio *gpio23_base = |
| 24 | (struct davinci_gpio *)DAVINCI_GPIO_BANK23; |
| 25 | struct davinci_gpio *gpio67_base = |
| 26 | (struct davinci_gpio *)DAVINCI_GPIO_BANK67; |
| 27 | |
| 28 | gd->bd->bi_arch_number = MACH_TYPE_DM355_LEOPARD; |
| 29 | gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100; |
| 30 | |
| 31 | /* GIO 9 & 10 are used for IO */ |
| 32 | writel((readl(PINMUX3) & 0XF8FFFFFF), PINMUX3); |
| 33 | |
| 34 | /* Interrupt set GIO 9 */ |
| 35 | writel((readl(DAVINCI_GPIO_BINTEN) | 0x1), DAVINCI_GPIO_BINTEN); |
| 36 | |
| 37 | /* set GIO 9 input */ |
| 38 | writel((readl(&gpio01_base->dir) | (1 << 9)), &gpio01_base->dir); |
| 39 | |
| 40 | /* Both edge trigger GIO 9 */ |
| 41 | writel((readl(&gpio01_base->set_rising) | (1 << 9)), |
| 42 | &gpio01_base->set_rising); |
| 43 | writel((readl(&gpio01_base->dir) & ~(1 << 5)), &gpio01_base->dir); |
| 44 | |
| 45 | /* output low */ |
| 46 | writel((readl(&gpio01_base->set_data) & ~(1 << 5)), |
| 47 | &gpio01_base->set_data); |
| 48 | |
| 49 | /* set GIO 10 output */ |
| 50 | writel((readl(&gpio01_base->dir) & ~(1 << 10)), &gpio01_base->dir); |
| 51 | |
| 52 | /* output high */ |
| 53 | writel((readl(&gpio01_base->set_data) | (1 << 10)), |
| 54 | &gpio01_base->set_data); |
| 55 | |
| 56 | /* set GIO 32 output */ |
| 57 | writel((readl(&gpio23_base->dir) & ~(1 << 0)), &gpio23_base->dir); |
| 58 | |
| 59 | /* output High */ |
| 60 | writel((readl(&gpio23_base->set_data) | (1 << 0)), |
| 61 | &gpio23_base->set_data); |
| 62 | |
| 63 | /* Enable UART1 MUX Lines */ |
| 64 | writel((readl(PINMUX0) & ~3), PINMUX0); |
| 65 | writel((readl(&gpio67_base->dir) & ~(1 << 6)), &gpio67_base->dir); |
| 66 | writel((readl(&gpio67_base->set_data) | (1 << 6)), |
| 67 | &gpio67_base->set_data); |
| 68 | |
| 69 | return 0; |
| 70 | } |
| 71 | |
| 72 | #ifdef CONFIG_DRIVER_DM9000 |
| 73 | int board_eth_init(bd_t *bis) |
| 74 | { |
| 75 | return dm9000_initialize(bis); |
| 76 | } |
| 77 | #endif |
| 78 | |
| 79 | #ifdef CONFIG_NAND_DAVINCI |
| 80 | int board_nand_init(struct nand_chip *nand) |
| 81 | { |
| 82 | davinci_nand_init(nand); |
| 83 | |
| 84 | return 0; |
| 85 | } |
| 86 | #endif |