blob: d73752c7f956b50d5380bb6b21108e223b41fea6 [file] [log] [blame]
Chris Packhama6477f72018-06-25 22:34:57 +12001/* SPDX-License-Identifier: GPL-2.0+ */
2/*
3 * (C) Copyright 2016 Allied Telesis <www.alliedtelesis.co.nz>
4 */
5
6#ifndef _CONFIG_SBX81LIFXCAT_H
7#define _CONFIG_SBX81LIFXCAT_H
8
9/*
10 * High Level Configuration Options (easy to change)
11 */
12#define CONFIG_FEROCEON_88FR131 1 /* CPU Core subversion */
13#define CONFIG_KW88F6281 1 /* SOC Name */
14#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
15#define CONFIG_SYS_KWD_CONFIG $(CONFIG_BOARDDIR)/kwbimage.cfg
16#define CONFIG_BUILD_TARGET "u-boot.kwb"
17
18/* additions for new ARM relocation support */
19#define CONFIG_SYS_SDRAM_BASE 0x00000000
20
21#define CONFIG_MD5 /* get_random_hex on krikwood needs MD5 support */
22#define CONFIG_KIRKWOOD_EGIGA_INIT /* Enable GbePort0/1 for kernel */
23#define CONFIG_KIRKWOOD_PCIE_INIT /* Enable PCIE Port0 */
24#define CONFIG_KIRKWOOD_RGMII_PAD_1V8 /* Set RGMII Pad voltage to 1.8V */
25#define CONFIG_KIRKWOOD_GPIO 1
26
Chris Packhama6477f72018-06-25 22:34:57 +120027/*
28 * NS16550 Configuration
29 */
30#define CONFIG_SYS_NS16550
31#define CONFIG_SYS_NS16550_SERIAL
32#define CONFIG_SYS_NS16550_REG_SIZE (-4)
33#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK
34#define CONFIG_SYS_NS16550_COM1 KW_UART0_BASE
35
36/*
37 * Serial Port configuration
38 * The following definitions let you select what serial you want to use
39 * for your console driver.
40 */
41
42#define CONFIG_CONS_INDEX 1 /*Console on UART0 */
43
44/*
45 * For booting Linux, the board info and command line data
46 * have to be in the first 8 MB of memory, since this is
47 * the maximum mapped by the Linux kernel during initialization.
48 */
49#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
50#define CONFIG_INITRD_TAG 1 /* enable INITRD tag */
51#define CONFIG_SETUP_MEMORY_TAGS 1 /* enable memory tag */
52
53#define MTDPARTS_DEFAULT "mtdparts=spi0.0:768K(boot)ro,256K(boot-env),14M(user),1M(errlog)"
54#define MTDPARTS_MTDOOPS "errlog"
55#define CONFIG_DOS_PARTITION
56
57/*
58 * Environment variables configurations
59 */
60#define CONFIG_ENV_SPI_BUS 0
61#define CONFIG_ENV_SPI_CS 0
62#define CONFIG_ENV_SPI_MAX_HZ 20000000 /* 20Mhz */
63#define CONFIG_ENV_SPI_MODE CONFIG_SF_DEFAULT_MODE
64#define CONFIG_ENV_SECT_SIZE 0x40000 /* 256K */
65#define CONFIG_ENV_SIZE 0x02000
66#define CONFIG_ENV_OFFSET 0xc0000 /* env starts here - 768K */
67
68/*
69 * U-Boot bootcode configuration
70 */
71
72#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for monitor */
73#define CONFIG_SYS_MALLOC_LEN (4 << 20) /* Reserve 4.0 MB for malloc */
74
75/*
76 * For booting Linux, the board info and command line data
77 * have to be in the first 8 MB of memory, since this is
78 * the maximum mapped by the Linux kernel during initialization.
79 */
80#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Mem map for Linux*/
81
82/* size in bytes reserved for initial data */
83
84#include <asm/arch/config.h>
85/* There is no PHY directly connected so don't ask it for link status */
86#undef CONFIG_SYS_FAULT_ECHO_LINK_DOWN
87
88/*
89 * Other required minimal configurations
90 */
91#define CONFIG_ARCH_CPU_INIT /* call arch_cpu_init() */
Chris Packhama6477f72018-06-25 22:34:57 +120092#define CONFIG_SYS_MEMTEST_START 0x00400000 /* 4M */
93#define CONFIG_SYS_MEMTEST_END 0x007fffff /*(_8M -1) */
94#define CONFIG_SYS_RESET_ADDRESS 0xffff0000 /* Rst Vector Adr */
95
96/*
97 * Ethernet Driver configuration
98 */
99#ifdef CONFIG_CMD_NET
100#define CONFIG_NETCONSOLE /* include NetConsole support */
101#define CONFIG_NET_MULTI /* specify more that one ports available */
Chris Packhama6477f72018-06-25 22:34:57 +1200102#define CONFIG_MVGBE /* Enable kirkwood Gbe Controller Driver */
103#define CONFIG_MVGBE_PORTS {1, 0} /* enable a single port */
104#define CONFIG_PHY_BASE_ADR 0x01
105#define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */
106#endif /* CONFIG_CMD_NET */
107
108#define CONFIG_SYS_LOAD_ADDR 0x1000000 /* default location for tftp and bootm */
109
110#endif /* _CONFIG_SBX81LIFXCAT_H */