blob: 07cda0fa67935c9153eaa9d44ddd8a692c7e28f9 [file] [log] [blame]
Stefan Boschc25e9e02020-07-10 19:07:28 +02001#include <common.h>
2#include <errno.h>
3#include <dm.h>
4#include <i2c.h>
5#include <log.h>
6#include <asm/arch/nexell.h>
7#include <asm/arch/reset.h>
8#include <asm/arch/clk.h>
9#include <asm/arch/nx_gpio.h>
Simon Glass401d1c42020-10-30 21:38:53 -060010#include <asm/global_data.h>
Stefan Boschc25e9e02020-07-10 19:07:28 +020011#include <linux/delay.h>
12
13#define I2C_WRITE 0
14#define I2C_READ 1
15
16#define I2CSTAT_MTM 0xC0 /* Master Transmit Mode */
17#define I2CSTAT_MRM 0x80 /* Master Receive Mode */
18#define I2CSTAT_BSY 0x20 /* Read: Bus Busy */
19#define I2CSTAT_SS 0x20 /* Write: START (1) / STOP (0) */
20#define I2CSTAT_RXTXEN 0x10 /* Rx/Tx enable */
21#define I2CSTAT_ABT 0x08 /* Arbitration bit */
22#define I2CSTAT_NACK 0x01 /* Nack bit */
23#define I2CCON_IRCLR 0x100 /* Interrupt Clear bit */
24#define I2CCON_ACKGEN 0x80 /* Acknowledge generation */
25#define I2CCON_TCP256 0x40 /* Tx-clock prescaler: 16 (0) / 256 (1) */
26#define I2CCON_IRENB 0x20 /* Interrupt Enable bit */
27#define I2CCON_IRPND 0x10 /* Interrupt pending bit */
28#define I2CCON_TCDMSK 0x0F /* I2C-bus transmit clock divider bit mask */
29
30#ifdef CONFIG_ARCH_S5P6818
31#define SDADLY_CLKSTEP 5 /* SDA delay: Reg. val. is multiple of 5 clks */
32#define SDADLY_MAX 3 /* SDA delay: Max. reg. value is 3 */
33#define I2CLC_FILTER 0x04 /* SDA filter on */
34#else
35#define STOPCON_CLR 0x01 /* Clock Line Release */
36#define STOPCON_DLR 0x02 /* Data Line Release */
37#define STOPCON_NAG 0x04 /* not-ackn. generation and data shift cont. */
38#endif
39
40#define I2C_TIMEOUT_MS 10 /* 10 ms */
41
42#define I2C_M_NOSTOP 0x100
43
44#define MAX_I2C_NUM 3
45
46#define DEFAULT_SPEED 100000 /* default I2C speed [Hz] */
47
48DECLARE_GLOBAL_DATA_PTR;
49
50struct nx_i2c_regs {
51 uint iiccon;
52 uint iicstat;
53 uint iicadd;
54 uint iicds;
55#ifdef CONFIG_ARCH_S5P6818
56 /* S5P6818: Offset 0x10 is Line Control Register (SDA-delay, Filter) */
57 uint iiclc;
58#else
59 /* S5P4418: Offset 0x10 is Stop Control Register */
60 uint iicstopcon;
61#endif
62};
63
64struct nx_i2c_bus {
65 uint bus_num;
66 struct nx_i2c_regs *regs;
67 uint speed;
68 uint target_speed;
69#ifdef CONFIG_ARCH_S5P6818
70 uint sda_delay;
71#else
72 /* setup time for Stop condition [us] */
73 uint tsu_stop;
74#endif
75};
76
77/* s5pxx18 i2c must be reset before enabled */
78static void i2c_reset(int ch)
79{
80 int rst_id = RESET_ID_I2C0 + ch;
81
82 nx_rstcon_setrst(rst_id, 0);
83 nx_rstcon_setrst(rst_id, 1);
84}
85
86static uint i2c_get_clkrate(struct nx_i2c_bus *bus)
87{
88 struct clk *clk;
89 int index = bus->bus_num;
90 char name[50] = {0, };
91
92 sprintf(name, "%s.%d", DEV_NAME_I2C, index);
93 clk = clk_get((const char *)name);
94 if (!clk)
95 return -1;
96
97 return clk_get_rate(clk);
98}
99
100static uint i2c_set_clk(struct nx_i2c_bus *bus, uint enb)
101{
102 struct clk *clk;
103 char name[50];
104
105 sprintf(name, "%s.%d", DEV_NAME_I2C, bus->bus_num);
106 clk = clk_get((const char *)name);
107 if (!clk) {
108 debug("%s(): clk_get(%s) error!\n",
109 __func__, (const char *)name);
110 return -EINVAL;
111 }
112
113 clk_disable(clk);
114 if (enb)
115 clk_enable(clk);
116
117 return 0;
118}
119
120#ifdef CONFIG_ARCH_S5P6818
121/* Set SDA line delay, not available at S5P4418 */
122static int nx_i2c_set_sda_delay(struct nx_i2c_bus *bus)
123{
124 struct nx_i2c_regs *i2c = bus->regs;
125 uint pclk = 0;
126 uint t_pclk = 0;
127 uint delay = 0;
128
129 /* get input clock of the I2C-controller */
130 pclk = i2c_get_clkrate(bus);
131
132 if (bus->sda_delay) {
133 /* t_pclk = period time of one pclk [ns] */
134 t_pclk = DIV_ROUND_UP(1000, pclk / 1000000);
135 /* delay = number of pclks required for sda_delay [ns] */
136 delay = DIV_ROUND_UP(bus->sda_delay, t_pclk);
137 /* delay = register value (step of 5 clocks) */
138 delay = DIV_ROUND_UP(delay, SDADLY_CLKSTEP);
139 /* max. possible register value = 3 */
140 if (delay > SDADLY_MAX) {
141 delay = SDADLY_MAX;
142 debug("%s(): sda-delay des.: %dns, sat. to max.: %dns (granularity: %dns)\n",
143 __func__, bus->sda_delay, t_pclk * delay * SDADLY_CLKSTEP,
144 t_pclk * SDADLY_CLKSTEP);
145 } else {
146 debug("%s(): sda-delay des.: %dns, act.: %dns (granularity: %dns)\n",
147 __func__, bus->sda_delay, t_pclk * delay * SDADLY_CLKSTEP,
148 t_pclk * SDADLY_CLKSTEP);
149 }
150
151 delay |= I2CLC_FILTER;
152 } else {
153 delay = 0;
154 debug("%s(): sda-delay = 0\n", __func__);
155 }
156
157 delay &= 0x7;
158 writel(delay, &i2c->iiclc);
159
160 return 0;
161}
162#endif
163
164static int nx_i2c_set_bus_speed(struct udevice *dev, uint speed)
165{
166 struct nx_i2c_bus *bus = dev_get_priv(dev);
167 struct nx_i2c_regs *i2c = bus->regs;
168 unsigned long pclk, pres = 16, div;
169
170 if (i2c_set_clk(bus, 1))
171 return -EINVAL;
172
173 /* get input clock of the I2C-controller */
174 pclk = i2c_get_clkrate(bus);
175
176 /* calculate prescaler and divisor values */
177 if ((pclk / pres / (16 + 1)) > speed)
178 /* prescaler value 16 is too less --> set to 256 */
179 pres = 256;
180
181 div = 0;
182 /* actual divider = div + 1 */
183 while ((pclk / pres / (div + 1)) > speed)
184 div++;
185
186 if (div > 0xF) {
187 debug("%s(): pres==%ld, div==0x%lx is saturated to 0xF !)\n",
188 __func__, pres, div);
189 div = 0xF;
190 } else {
191 debug("%s(): pres==%ld, div==0x%lx)\n", __func__, pres, div);
192 }
193
194 /* set Tx-clock divisor and prescaler values */
195 writel((div & I2CCON_TCDMSK) | ((pres == 256) ? I2CCON_TCP256 : 0),
196 &i2c->iiccon);
197
198 /* init to SLAVE REVEIVE and set slaveaddr */
199 writel(0, &i2c->iicstat);
200 writel(0x00, &i2c->iicadd);
201
202 /* program Master Transmit (and implicit STOP) */
203 writel(I2CSTAT_MTM | I2CSTAT_RXTXEN, &i2c->iicstat);
204
205 /* calculate actual I2C speed [Hz] */
206 bus->speed = pclk / ((div + 1) * pres);
207 debug("%s(): speed des.: %dHz, act.: %dHz\n",
208 __func__, speed, bus->speed);
209
210#ifdef CONFIG_ARCH_S5P6818
211 nx_i2c_set_sda_delay(bus);
212#else
213 /* setup time for Stop condition [us], min. 4us @ 100kHz I2C-clock */
214 bus->tsu_stop = DIV_ROUND_UP(400, bus->speed / 1000);
215#endif
216
217 if (i2c_set_clk(bus, 0))
218 return -EINVAL;
219 return 0;
220}
221
222static void i2c_process_node(struct udevice *dev)
223{
224 struct nx_i2c_bus *bus = dev_get_priv(dev);
225
226 bus->target_speed = dev_read_s32_default(dev, "clock-frequency",
227 DEFAULT_SPEED);
228#ifdef CONFIG_ARCH_S5P6818
229 bus->sda_delay = dev_read_s32_default(dev, "i2c-sda-delay-ns", 0);
230#endif
231}
232
233static int nx_i2c_probe(struct udevice *dev)
234{
235 struct nx_i2c_bus *bus = dev_get_priv(dev);
236 fdt_addr_t addr;
237
238 /* get regs = i2c base address */
239 addr = devfdt_get_addr(dev);
240 if (addr == FDT_ADDR_T_NONE)
241 return -EINVAL;
242 bus->regs = (struct nx_i2c_regs *)addr;
243
Simon Glass8b85dfc2020-12-16 21:20:07 -0700244 bus->bus_num = dev_seq(dev);
Stefan Boschc25e9e02020-07-10 19:07:28 +0200245
246 /* i2c node parsing */
247 i2c_process_node(dev);
248 if (!bus->target_speed)
249 return -ENODEV;
250
251 /* reset */
252 i2c_reset(bus->bus_num);
253
254 return 0;
255}
256
257/* i2c bus busy check */
258static int i2c_is_busy(struct nx_i2c_regs *i2c)
259{
260 ulong start_time;
261
262 start_time = get_timer(0);
263 while (readl(&i2c->iicstat) & I2CSTAT_BSY) {
264 if (get_timer(start_time) > I2C_TIMEOUT_MS) {
265 debug("Timeout\n");
266 return -EBUSY;
267 }
268 }
269 return 0;
270}
271
272/* irq enable/disable functions */
273static void i2c_enable_irq(struct nx_i2c_regs *i2c)
274{
275 unsigned int reg;
276
277 reg = readl(&i2c->iiccon);
278 reg |= I2CCON_IRENB;
279 writel(reg, &i2c->iiccon);
280}
281
282/* irq clear function */
283static void i2c_clear_irq(struct nx_i2c_regs *i2c)
284{
285 unsigned int reg;
286
287 reg = readl(&i2c->iiccon);
288 /* reset interrupt pending flag */
289 reg &= ~(I2CCON_IRPND);
290 /*
291 * Interrupt must also be cleared!
292 * Otherwise linux boot may hang after:
293 * [ 0.436000] NetLabel: unlabeled traffic allowed by default
294 * Next would be:
295 * [ 0.442000] clocksource: Switched to clocksource source timer
296 */
297 reg |= I2CCON_IRCLR;
298 writel(reg, &i2c->iiccon);
299}
300
301/* ack enable functions */
302static void i2c_enable_ack(struct nx_i2c_regs *i2c)
303{
304 unsigned int reg;
305
306 reg = readl(&i2c->iiccon);
307 reg |= I2CCON_ACKGEN;
308 writel(reg, &i2c->iiccon);
309}
310
311static void i2c_send_stop(struct nx_i2c_bus *bus)
312{
313 struct nx_i2c_regs *i2c = bus->regs;
314
315 if (IS_ENABLED(CONFIG_ARCH_S5P6818)) {
316 unsigned int reg;
317
318 reg = readl(&i2c->iicstat);
319 reg |= I2CSTAT_MRM | I2CSTAT_RXTXEN;
320 reg &= (~I2CSTAT_SS);
321
322 writel(reg, &i2c->iicstat);
323 i2c_clear_irq(i2c);
324 } else { /* S5P4418 */
325 writel(STOPCON_NAG, &i2c->iicstopcon);
326
327 i2c_clear_irq(i2c);
328
329 /*
330 * Clock Line Release --> SDC changes from Low to High and
331 * SDA from High to Low
332 */
333 writel(STOPCON_CLR, &i2c->iicstopcon);
334
335 /* Hold SDA Low (Setup Time for Stop condition) */
336 udelay(bus->tsu_stop);
337
338 i2c_clear_irq(i2c);
339
340 /* Master Receive Mode Stop --> SDA becomes High */
341 writel(I2CSTAT_MRM, &i2c->iicstat);
342 }
343}
344
345static int wait_for_xfer(struct nx_i2c_regs *i2c)
346{
347 unsigned long start_time = get_timer(0);
348
349 do {
350 if (readl(&i2c->iiccon) & I2CCON_IRPND)
351 /* return -EREMOTEIO if not Acknowledged, otherwise 0 */
352 return (readl(&i2c->iicstat) & I2CSTAT_NACK) ?
353 -EREMOTEIO : 0;
354 } while (get_timer(start_time) < I2C_TIMEOUT_MS);
355
356 return -ETIMEDOUT;
357}
358
359static int i2c_transfer(struct nx_i2c_regs *i2c,
360 uchar cmd_type,
361 uchar chip_addr,
362 uchar addr[],
363 uchar addr_len,
364 uchar data[],
365 unsigned short data_len,
366 uint seq)
367{
368 uint status;
369 int i = 0, result;
370
371 /* Note: data_len = 0 is supported for "probe_chip" */
372
373 i2c_enable_irq(i2c);
374 i2c_enable_ack(i2c);
375
376 /* Get the slave chip address going */
377 /* Enable Rx/Tx */
378 writel(I2CSTAT_RXTXEN, &i2c->iicstat);
379
380 writel(chip_addr, &i2c->iicds);
381 status = I2CSTAT_RXTXEN | I2CSTAT_SS;
382 if (cmd_type == I2C_WRITE || (addr && addr_len))
383 status |= I2CSTAT_MTM;
384 else
385 status |= I2CSTAT_MRM;
386
387 writel(status, &i2c->iicstat);
388 if (seq)
389 i2c_clear_irq(i2c);
390
391 /* Wait for chip address to transmit. */
392 result = wait_for_xfer(i2c);
393 if (result) {
394 debug("%s: transmitting chip address failed\n", __func__);
395 goto bailout;
396 }
397
398 /* If register address needs to be transmitted - do it now. */
399 if (addr && addr_len) { /* register addr */
400 while ((i < addr_len) && !result) {
401 writel(addr[i++], &i2c->iicds);
402 i2c_clear_irq(i2c);
403 result = wait_for_xfer(i2c);
404 }
405
406 i = 0;
407 if (result) {
408 debug("%s: transmitting register address failed\n",
409 __func__);
410 goto bailout;
411 }
412 }
413
414 switch (cmd_type) {
415 case I2C_WRITE:
416 while ((i < data_len) && !result) {
417 writel(data[i++], &i2c->iicds);
418 i2c_clear_irq(i2c);
419 result = wait_for_xfer(i2c);
420 }
421 break;
422 case I2C_READ:
423 if (addr && addr_len) {
424 /*
425 * Register address has been sent, now send slave chip
426 * address again to start the actual read transaction.
427 */
428 writel(chip_addr, &i2c->iicds);
429
430 /* Generate a re-START. */
431 writel(I2CSTAT_MRM | I2CSTAT_RXTXEN |
432 I2CSTAT_SS, &i2c->iicstat);
433 i2c_clear_irq(i2c);
434 result = wait_for_xfer(i2c);
435 if (result) {
436 debug("%s: I2C_READ: sending chip addr. failed\n",
437 __func__);
438 goto bailout;
439 }
440 }
441
442 while ((i < data_len) && !result) {
443 /* disable ACK for final READ */
444 if (i == data_len - 1)
445 clrbits_le32(&i2c->iiccon, I2CCON_ACKGEN);
446
447 i2c_clear_irq(i2c);
448 result = wait_for_xfer(i2c);
449 data[i++] = readb(&i2c->iicds);
450 }
451
452 if (result == -EREMOTEIO)
453 /* Not Acknowledged --> normal terminated read. */
454 result = 0;
455 else if (result == -ETIMEDOUT)
456 debug("%s: I2C_READ: time out\n", __func__);
457 else
458 debug("%s: I2C_READ: read not terminated with NACK\n",
459 __func__);
460 break;
461
462 default:
463 debug("%s: bad call\n", __func__);
464 result = -EINVAL;
465 break;
466 }
467
468bailout:
469 return result;
470}
471
472static int nx_i2c_read(struct udevice *dev, uchar chip_addr, uint addr,
473 uint alen, uchar *buffer, uint len, uint seq)
474{
475 struct nx_i2c_bus *i2c;
476 uchar xaddr[4];
477 int ret;
478
479 i2c = dev_get_priv(dev);
480 if (!i2c)
481 return -EFAULT;
482
483 if (alen > 4) {
484 debug("I2C read: addr len %d not supported\n", alen);
485 return -EADDRNOTAVAIL;
486 }
487
488 if (alen > 0)
489 xaddr[0] = (addr >> 24) & 0xFF;
490
491 if (alen > 0) {
492 xaddr[0] = (addr >> 24) & 0xFF;
493 xaddr[1] = (addr >> 16) & 0xFF;
494 xaddr[2] = (addr >> 8) & 0xFF;
495 xaddr[3] = addr & 0xFF;
496 }
497
498 ret = i2c_transfer(i2c->regs, I2C_READ, chip_addr << 1,
499 &xaddr[4 - alen], alen, buffer, len, seq);
500
501 if (ret) {
502 debug("I2C read failed %d\n", ret);
503 return -EIO;
504 }
505
506 return 0;
507}
508
509static int nx_i2c_write(struct udevice *dev, uchar chip_addr, uint addr,
510 uint alen, uchar *buffer, uint len, uint seq)
511{
512 struct nx_i2c_bus *i2c;
513 uchar xaddr[4];
514 int ret;
515
516 i2c = dev_get_priv(dev);
517 if (!i2c)
518 return -EFAULT;
519
520 if (alen > 4) {
521 debug("I2C write: addr len %d not supported\n", alen);
522 return -EINVAL;
523 }
524
525 if (alen > 0) {
526 xaddr[0] = (addr >> 24) & 0xFF;
527 xaddr[1] = (addr >> 16) & 0xFF;
528 xaddr[2] = (addr >> 8) & 0xFF;
529 xaddr[3] = addr & 0xFF;
530 }
531
532 ret = i2c_transfer(i2c->regs, I2C_WRITE, chip_addr << 1,
533 &xaddr[4 - alen], alen, buffer, len, seq);
534 if (ret) {
535 debug("I2C write failed %d\n", ret);
536 return -EIO;
537 }
538
539 return 0;
540}
541
542static int nx_i2c_xfer(struct udevice *dev, struct i2c_msg *msg, int nmsgs)
543{
544 struct nx_i2c_bus *bus = dev_get_priv(dev);
545 struct nx_i2c_regs *i2c = bus->regs;
546 int ret;
547 int i;
548
549 /* The power loss by the clock, only during on/off. */
550 ret = i2c_set_clk(bus, 1);
551
552 if (!ret)
553 /* Bus State(Busy) check */
554 ret = i2c_is_busy(i2c);
555 if (!ret) {
556 for (i = 0; i < nmsgs; msg++, i++) {
557 if (msg->flags & I2C_M_RD) {
558 ret = nx_i2c_read(dev, msg->addr, 0, 0,
559 msg->buf, msg->len, i);
560 } else {
561 ret = nx_i2c_write(dev, msg->addr, 0, 0,
562 msg->buf, msg->len, i);
563 }
564
565 if (ret) {
566 debug("i2c_xfer: error sending\n");
567 ret = -EREMOTEIO;
568 }
569 }
570
571 i2c_send_stop(bus);
572 if (i2c_set_clk(bus, 0))
573 ret = -EINVAL;
574 }
575
576 return ret;
577};
578
579static int nx_i2c_probe_chip(struct udevice *dev, u32 chip_addr,
580 u32 chip_flags)
581{
582 int ret;
583 struct nx_i2c_bus *bus = dev_get_priv(dev);
584
585 ret = i2c_set_clk(bus, 1);
586
587 if (!ret) {
588 /*
589 * Send Chip Address only
590 * --> I2C transfer with data length and address length = 0.
591 * If there is a Slave, i2c_transfer() returns 0 (acknowledge
592 * transfer).
593 * I2C_WRITE must be used in order Master Transmit Mode is
594 * selected. Otherwise (in Master Receive Mode, I2C_READ)
595 * sending the stop condition below is not working (SDA does
596 * not transit to High).
597 */
598 ret = i2c_transfer(bus->regs, I2C_WRITE, (uchar)chip_addr << 1,
599 NULL, 0, NULL, 0, 0);
600
601 i2c_send_stop(bus);
602 if (i2c_set_clk(bus, 0))
603 ret = -EINVAL;
604 }
605
606 return ret;
607}
608
609static const struct dm_i2c_ops nx_i2c_ops = {
610 .xfer = nx_i2c_xfer,
611 .probe_chip = nx_i2c_probe_chip,
612 .set_bus_speed = nx_i2c_set_bus_speed,
613};
614
615static const struct udevice_id nx_i2c_ids[] = {
616 { .compatible = "nexell,s5pxx18-i2c" },
617 { }
618};
619
620U_BOOT_DRIVER(i2c_nexell) = {
621 .name = "i2c_nexell",
622 .id = UCLASS_I2C,
623 .of_match = nx_i2c_ids,
624 .probe = nx_i2c_probe,
Simon Glass41575d82020-12-03 16:55:17 -0700625 .priv_auto = sizeof(struct nx_i2c_bus),
Stefan Boschc25e9e02020-07-10 19:07:28 +0200626 .ops = &nx_i2c_ops,
627};