blob: c534cc07e09275f2eb96249d638ea2b5c3211b2c [file] [log] [blame]
Sean Andersonf9c7d4f2020-06-24 06:41:11 -04001// SPDX-License-Identifier: GPL-2.0+
2/*
3 * Copyright (C) 2019-20 Sean Anderson <seanga2@gmail.com>
4 */
Sean Andersonaf9f9972021-06-11 00:16:09 -04005#define LOG_CATEGORY UCLASS_CLK
Sean Andersonf9c7d4f2020-06-24 06:41:11 -04006
Sean Anderson609bd602021-06-11 00:16:08 -04007#include <common.h>
Sean Andersonaf9f9972021-06-11 00:16:09 -04008#include <clk.h>
9#include <clk-uclass.h>
10#include <div64.h>
Sean Andersonf9c7d4f2020-06-24 06:41:11 -040011#include <dm.h>
12#include <log.h>
13#include <mapmem.h>
Sean Andersonaf9f9972021-06-11 00:16:09 -040014#include <serial.h>
15#include <dt-bindings/clock/k210-sysctl.h>
16#include <dt-bindings/mfd/k210-sysctl.h>
Damien Le Moalfd426b32022-03-01 10:35:39 +000017#include <k210/pll.h>
Sean Andersonaf9f9972021-06-11 00:16:09 -040018#include <linux/bitfield.h>
19
Sean Anderson29e30672021-06-11 00:16:11 -040020DECLARE_GLOBAL_DATA_PTR;
21
Sean Andersonaf9f9972021-06-11 00:16:09 -040022/**
23 * struct k210_clk_priv - K210 clock driver private data
24 * @base: The base address of the sysctl device
25 * @in0: The "in0" external oscillator
26 */
27struct k210_clk_priv {
28 void __iomem *base;
29 struct clk in0;
30};
Sean Andersonf9c7d4f2020-06-24 06:41:11 -040031
Sean Andersonf9c7d4f2020-06-24 06:41:11 -040032/*
33 * All parameters for different sub-clocks are collected into parameter arrays.
34 * These parameters are then initialized by the clock which uses them during
35 * probe. To save space, ids are automatically generated for each sub-clock by
36 * using an enum. Instead of storing a parameter struct for each clock, even for
37 * those clocks which don't use a particular type of sub-clock, we can just
38 * store the parameters for the clocks which need them.
39 *
40 * So why do it like this? Arranging all the sub-clocks together makes it very
41 * easy to find bugs in the code.
42 */
43
Sean Anderson609bd602021-06-11 00:16:08 -040044/**
45 * enum k210_clk_div_type - The type of divider
46 * @K210_DIV_ONE: freq = parent / (reg + 1)
47 * @K210_DIV_EVEN: freq = parent / 2 / (reg + 1)
48 * @K210_DIV_POWER: freq = parent / (2 << reg)
49 * @K210_DIV_FIXED: freq = parent / factor
50 */
51enum k210_clk_div_type {
52 K210_DIV_ONE,
53 K210_DIV_EVEN,
54 K210_DIV_POWER,
55 K210_DIV_FIXED,
56};
57
58/**
59 * struct k210_div_params - Parameters for dividing clocks
60 * @type: An &enum k210_clk_div_type specifying the dividing formula
61 * @off: The offset of the divider from the sysctl base address
62 * @shift: The offset of the LSB of the divider
63 * @width: The number of bits in the divider
64 * @div: The fixed divisor for this divider
65 */
66struct k210_div_params {
67 u8 type;
68 union {
69 struct {
70 u8 off;
71 u8 shift;
72 u8 width;
73 };
74 u8 div;
75 };
76};
77
Sean Andersonf9c7d4f2020-06-24 06:41:11 -040078#define DIV_LIST \
Sean Anderson609bd602021-06-11 00:16:08 -040079 DIV(K210_CLK_ACLK, K210_SYSCTL_SEL0, 1, 2, K210_DIV_POWER) \
80 DIV(K210_CLK_APB0, K210_SYSCTL_SEL0, 3, 3, K210_DIV_ONE) \
81 DIV(K210_CLK_APB1, K210_SYSCTL_SEL0, 6, 3, K210_DIV_ONE) \
82 DIV(K210_CLK_APB2, K210_SYSCTL_SEL0, 9, 3, K210_DIV_ONE) \
83 DIV(K210_CLK_SRAM0, K210_SYSCTL_THR0, 0, 4, K210_DIV_ONE) \
84 DIV(K210_CLK_SRAM1, K210_SYSCTL_THR0, 4, 4, K210_DIV_ONE) \
85 DIV(K210_CLK_AI, K210_SYSCTL_THR0, 8, 4, K210_DIV_ONE) \
86 DIV(K210_CLK_DVP, K210_SYSCTL_THR0, 12, 4, K210_DIV_ONE) \
87 DIV(K210_CLK_ROM, K210_SYSCTL_THR0, 16, 4, K210_DIV_ONE) \
88 DIV(K210_CLK_SPI0, K210_SYSCTL_THR1, 0, 8, K210_DIV_EVEN) \
89 DIV(K210_CLK_SPI1, K210_SYSCTL_THR1, 8, 8, K210_DIV_EVEN) \
90 DIV(K210_CLK_SPI2, K210_SYSCTL_THR1, 16, 8, K210_DIV_EVEN) \
91 DIV(K210_CLK_SPI3, K210_SYSCTL_THR1, 24, 8, K210_DIV_EVEN) \
92 DIV(K210_CLK_TIMER0, K210_SYSCTL_THR2, 0, 8, K210_DIV_EVEN) \
93 DIV(K210_CLK_TIMER1, K210_SYSCTL_THR2, 8, 8, K210_DIV_EVEN) \
94 DIV(K210_CLK_TIMER2, K210_SYSCTL_THR2, 16, 8, K210_DIV_EVEN) \
95 DIV(K210_CLK_I2S0, K210_SYSCTL_THR3, 0, 16, K210_DIV_EVEN) \
96 DIV(K210_CLK_I2S1, K210_SYSCTL_THR3, 16, 16, K210_DIV_EVEN) \
97 DIV(K210_CLK_I2S2, K210_SYSCTL_THR4, 0, 16, K210_DIV_EVEN) \
98 DIV(K210_CLK_I2S0_M, K210_SYSCTL_THR4, 16, 8, K210_DIV_EVEN) \
99 DIV(K210_CLK_I2S1_M, K210_SYSCTL_THR4, 24, 8, K210_DIV_EVEN) \
100 DIV(K210_CLK_I2S2_M, K210_SYSCTL_THR4, 0, 8, K210_DIV_EVEN) \
101 DIV(K210_CLK_I2C0, K210_SYSCTL_THR5, 8, 8, K210_DIV_EVEN) \
102 DIV(K210_CLK_I2C1, K210_SYSCTL_THR5, 16, 8, K210_DIV_EVEN) \
103 DIV(K210_CLK_I2C2, K210_SYSCTL_THR5, 24, 8, K210_DIV_EVEN) \
104 DIV(K210_CLK_WDT0, K210_SYSCTL_THR6, 0, 8, K210_DIV_EVEN) \
105 DIV(K210_CLK_WDT1, K210_SYSCTL_THR6, 8, 8, K210_DIV_EVEN) \
106 DIV_FIXED(K210_CLK_CLINT, 50) \
Sean Andersonf9c7d4f2020-06-24 06:41:11 -0400107
108#define _DIVIFY(id) K210_CLK_DIV_##id
109#define DIVIFY(id) _DIVIFY(id)
110
Sean Anderson609bd602021-06-11 00:16:08 -0400111enum k210_div_id {
112#define DIV(id, ...) DIVIFY(id),
113#define DIV_FIXED DIV
Sean Andersonf9c7d4f2020-06-24 06:41:11 -0400114 DIV_LIST
Sean Anderson609bd602021-06-11 00:16:08 -0400115#undef DIV
116#undef DIV_FIXED
117 K210_CLK_DIV_NONE,
Sean Andersonf9c7d4f2020-06-24 06:41:11 -0400118};
119
120static const struct k210_div_params k210_divs[] = {
Sean Anderson609bd602021-06-11 00:16:08 -0400121#define DIV(id, _off, _shift, _width, _type) \
Sean Andersonf9c7d4f2020-06-24 06:41:11 -0400122 [DIVIFY(id)] = { \
Sean Anderson609bd602021-06-11 00:16:08 -0400123 .type = (_type), \
Sean Andersonf9c7d4f2020-06-24 06:41:11 -0400124 .off = (_off), \
125 .shift = (_shift), \
126 .width = (_width), \
Sean Anderson609bd602021-06-11 00:16:08 -0400127 },
128#define DIV_FIXED(id, _div) \
129 [DIVIFY(id)] = { \
130 .type = K210_DIV_FIXED, \
131 .div = (_div) \
Sean Andersonf9c7d4f2020-06-24 06:41:11 -0400132 },
133 DIV_LIST
Sean Anderson609bd602021-06-11 00:16:08 -0400134#undef DIV
135#undef DIV_FIXED
Sean Andersonf9c7d4f2020-06-24 06:41:11 -0400136};
137
138#undef DIV
139#undef DIV_LIST
140
Sean Anderson609bd602021-06-11 00:16:08 -0400141/**
142 * struct k210_gate_params - Parameters for gated clocks
143 * @off: The offset of the gate from the sysctl base address
144 * @bit_idx: The index of the bit within the register
145 */
146struct k210_gate_params {
147 u8 off;
148 u8 bit_idx;
149};
150
Sean Andersonf9c7d4f2020-06-24 06:41:11 -0400151#define GATE_LIST \
152 GATE(K210_CLK_CPU, K210_SYSCTL_EN_CENT, 0) \
153 GATE(K210_CLK_SRAM0, K210_SYSCTL_EN_CENT, 1) \
154 GATE(K210_CLK_SRAM1, K210_SYSCTL_EN_CENT, 2) \
155 GATE(K210_CLK_APB0, K210_SYSCTL_EN_CENT, 3) \
156 GATE(K210_CLK_APB1, K210_SYSCTL_EN_CENT, 4) \
157 GATE(K210_CLK_APB2, K210_SYSCTL_EN_CENT, 5) \
158 GATE(K210_CLK_ROM, K210_SYSCTL_EN_PERI, 0) \
159 GATE(K210_CLK_DMA, K210_SYSCTL_EN_PERI, 1) \
160 GATE(K210_CLK_AI, K210_SYSCTL_EN_PERI, 2) \
161 GATE(K210_CLK_DVP, K210_SYSCTL_EN_PERI, 3) \
162 GATE(K210_CLK_FFT, K210_SYSCTL_EN_PERI, 4) \
163 GATE(K210_CLK_GPIO, K210_SYSCTL_EN_PERI, 5) \
164 GATE(K210_CLK_SPI0, K210_SYSCTL_EN_PERI, 6) \
165 GATE(K210_CLK_SPI1, K210_SYSCTL_EN_PERI, 7) \
166 GATE(K210_CLK_SPI2, K210_SYSCTL_EN_PERI, 8) \
167 GATE(K210_CLK_SPI3, K210_SYSCTL_EN_PERI, 9) \
168 GATE(K210_CLK_I2S0, K210_SYSCTL_EN_PERI, 10) \
169 GATE(K210_CLK_I2S1, K210_SYSCTL_EN_PERI, 11) \
170 GATE(K210_CLK_I2S2, K210_SYSCTL_EN_PERI, 12) \
171 GATE(K210_CLK_I2C0, K210_SYSCTL_EN_PERI, 13) \
172 GATE(K210_CLK_I2C1, K210_SYSCTL_EN_PERI, 14) \
173 GATE(K210_CLK_I2C2, K210_SYSCTL_EN_PERI, 15) \
174 GATE(K210_CLK_UART1, K210_SYSCTL_EN_PERI, 16) \
175 GATE(K210_CLK_UART2, K210_SYSCTL_EN_PERI, 17) \
176 GATE(K210_CLK_UART3, K210_SYSCTL_EN_PERI, 18) \
177 GATE(K210_CLK_AES, K210_SYSCTL_EN_PERI, 19) \
178 GATE(K210_CLK_FPIOA, K210_SYSCTL_EN_PERI, 20) \
179 GATE(K210_CLK_TIMER0, K210_SYSCTL_EN_PERI, 21) \
180 GATE(K210_CLK_TIMER1, K210_SYSCTL_EN_PERI, 22) \
181 GATE(K210_CLK_TIMER2, K210_SYSCTL_EN_PERI, 23) \
182 GATE(K210_CLK_WDT0, K210_SYSCTL_EN_PERI, 24) \
183 GATE(K210_CLK_WDT1, K210_SYSCTL_EN_PERI, 25) \
184 GATE(K210_CLK_SHA, K210_SYSCTL_EN_PERI, 26) \
185 GATE(K210_CLK_OTP, K210_SYSCTL_EN_PERI, 27) \
186 GATE(K210_CLK_RTC, K210_SYSCTL_EN_PERI, 29)
187
188#define _GATEIFY(id) K210_CLK_GATE_##id
189#define GATEIFY(id) _GATEIFY(id)
190
Sean Anderson609bd602021-06-11 00:16:08 -0400191enum k210_gate_id {
Sean Andersonf9c7d4f2020-06-24 06:41:11 -0400192#define GATE(id, ...) GATEIFY(id),
193 GATE_LIST
194#undef GATE
Sean Anderson609bd602021-06-11 00:16:08 -0400195 K210_CLK_GATE_NONE,
Sean Andersonf9c7d4f2020-06-24 06:41:11 -0400196};
197
198static const struct k210_gate_params k210_gates[] = {
199#define GATE(id, _off, _idx) \
200 [GATEIFY(id)] = { \
201 .off = (_off), \
202 .bit_idx = (_idx), \
203 },
204 GATE_LIST
205#undef GATE
206};
207
208#undef GATE_LIST
209
Sean Anderson609bd602021-06-11 00:16:08 -0400210/* The most parents is PLL2 */
211#define K210_CLK_MAX_PARENTS 3
212
213/**
214 * struct k210_mux_params - Parameters for muxed clocks
215 * @parents: A list of parent clock ids
216 * @num_parents: The number of parent clocks
217 * @off: The offset of the mux from the base sysctl address
218 * @shift: The offset of the LSB of the mux selector
219 * @width: The number of bits in the mux selector
220 */
221struct k210_mux_params {
222 u8 parents[K210_CLK_MAX_PARENTS];
223 u8 num_parents;
224 u8 off;
225 u8 shift;
226 u8 width;
227};
228
Sean Andersonf9c7d4f2020-06-24 06:41:11 -0400229#define MUX(id, reg, shift, width) \
Sean Anderson609bd602021-06-11 00:16:08 -0400230 MUX_PARENTS(id, reg, shift, width, K210_CLK_IN0, K210_CLK_PLL0)
Sean Andersonf9c7d4f2020-06-24 06:41:11 -0400231#define MUX_LIST \
Sean Anderson609bd602021-06-11 00:16:08 -0400232 MUX_PARENTS(K210_CLK_PLL2, K210_SYSCTL_PLL2, 26, 2, \
233 K210_CLK_IN0, K210_CLK_PLL0, K210_CLK_PLL1) \
234 MUX(K210_CLK_ACLK, K210_SYSCTL_SEL0, 0, 1) \
Sean Andersonf9c7d4f2020-06-24 06:41:11 -0400235 MUX(K210_CLK_SPI3, K210_SYSCTL_SEL0, 12, 1) \
236 MUX(K210_CLK_TIMER0, K210_SYSCTL_SEL0, 13, 1) \
237 MUX(K210_CLK_TIMER1, K210_SYSCTL_SEL0, 14, 1) \
238 MUX(K210_CLK_TIMER2, K210_SYSCTL_SEL0, 15, 1)
239
240#define _MUXIFY(id) K210_CLK_MUX_##id
241#define MUXIFY(id) _MUXIFY(id)
242
Sean Anderson609bd602021-06-11 00:16:08 -0400243enum k210_mux_id {
Sean Andersonf9c7d4f2020-06-24 06:41:11 -0400244#define MUX_PARENTS(id, ...) MUXIFY(id),
245 MUX_LIST
246#undef MUX_PARENTS
247 K210_CLK_MUX_NONE,
248};
249
Sean Andersonf9c7d4f2020-06-24 06:41:11 -0400250static const struct k210_mux_params k210_muxes[] = {
Sean Anderson609bd602021-06-11 00:16:08 -0400251#define MUX_PARENTS(id, _off, _shift, _width, ...) \
Sean Andersonf9c7d4f2020-06-24 06:41:11 -0400252 [MUXIFY(id)] = { \
Sean Anderson609bd602021-06-11 00:16:08 -0400253 .parents = { __VA_ARGS__ }, \
254 .num_parents = __count_args(__VA_ARGS__), \
Sean Andersonf9c7d4f2020-06-24 06:41:11 -0400255 .off = (_off), \
256 .shift = (_shift), \
257 .width = (_width), \
258 },
259 MUX_LIST
260#undef MUX_PARENTS
261};
262
263#undef MUX
264#undef MUX_LIST
265
Sean Anderson609bd602021-06-11 00:16:08 -0400266/**
Sean Andersonaf9f9972021-06-11 00:16:09 -0400267 * struct k210_pll_params - K210 PLL parameters
268 * @off: The offset of the PLL from the base sysctl address
269 * @shift: The offset of the LSB of the lock status
270 * @width: The number of bits in the lock status
271 */
272struct k210_pll_params {
273 u8 off;
274 u8 shift;
275 u8 width;
276};
277
278static const struct k210_pll_params k210_plls[] = {
279#define PLL(_off, _shift, _width) { \
280 .off = (_off), \
281 .shift = (_shift), \
282 .width = (_width), \
283}
284 [0] = PLL(K210_SYSCTL_PLL0, 0, 2),
285 [1] = PLL(K210_SYSCTL_PLL1, 8, 1),
286 [2] = PLL(K210_SYSCTL_PLL2, 16, 1),
287#undef PLL
288};
289
290/**
Sean Anderson609bd602021-06-11 00:16:08 -0400291 * enum k210_clk_flags - The type of a K210 clock
292 * @K210_CLKF_MUX: This clock has a mux and not a static parent
293 * @K210_CLKF_PLL: This clock is a PLL
294 */
295enum k210_clk_flags {
296 K210_CLKF_MUX = BIT(0),
297 K210_CLKF_PLL = BIT(1),
Sean Andersonf9c7d4f2020-06-24 06:41:11 -0400298};
299
Sean Anderson609bd602021-06-11 00:16:08 -0400300/**
301 * struct k210_clk_params - The parameters defining a K210 clock
302 * @name: The name of the clock
303 * @flags: A set of &enum k210_clk_flags defining which fields are valid
304 * @mux: An &enum k210_mux_id of this clock's mux
305 * @parent: The clock id of this clock's parent
306 * @pll: The id of the PLL (if this clock is a PLL)
307 * @div: An &enum k210_div_id of this clock's divider
308 * @gate: An &enum k210_gate_id of this clock's gate
309 */
310struct k210_clk_params {
Simon Glass8dd86202023-02-05 15:36:26 -0700311#if IS_ENABLED(CONFIG_CMD_CLK)
Sean Anderson609bd602021-06-11 00:16:08 -0400312 const char *name;
313#endif
314 u8 flags;
315 union {
316 u8 parent;
317 u8 mux;
318 };
319 union {
320 u8 pll;
321 struct {
322 u8 div;
323 u8 gate;
324 };
325 };
Sean Andersonf9c7d4f2020-06-24 06:41:11 -0400326};
327
Sean Anderson609bd602021-06-11 00:16:08 -0400328static const struct k210_clk_params k210_clks[] = {
Simon Glass8dd86202023-02-05 15:36:26 -0700329#if IS_ENABLED(CONFIG_CMD_CLK)
Sean Anderson609bd602021-06-11 00:16:08 -0400330#define NAME(_name) .name = (_name),
331#else
332#define NAME(name)
333#endif
334#define CLK(id, _name, _parent, _div, _gate) \
335 [id] = { \
336 NAME(_name) \
337 .parent = (_parent), \
338 .div = (_div), \
339 .gate = (_gate), \
340 }
341#define CLK_MUX(id, _name, _mux, _div, _gate) \
342 [id] = { \
343 NAME(_name) \
344 .flags = K210_CLKF_MUX, \
Sean Andersonf9c7d4f2020-06-24 06:41:11 -0400345 .mux = (_mux), \
346 .div = (_div), \
347 .gate = (_gate), \
Sean Anderson609bd602021-06-11 00:16:08 -0400348 }
349#define CLK_PLL(id, _pll, _parent) \
350 [id] = { \
351 NAME("pll" #_pll) \
352 .flags = K210_CLKF_PLL, \
353 .parent = (_parent), \
354 .pll = (_pll), \
355 }
356#define CLK_FULL(id, name) \
357 CLK_MUX(id, name, MUXIFY(id), DIVIFY(id), GATEIFY(id))
358#define CLK_NOMUX(id, name, parent) \
359 CLK(id, name, parent, DIVIFY(id), GATEIFY(id))
360#define CLK_DIV(id, name, parent) \
361 CLK(id, name, parent, DIVIFY(id), K210_CLK_GATE_NONE)
362#define CLK_GATE(id, name, parent) \
363 CLK(id, name, parent, K210_CLK_DIV_NONE, GATEIFY(id))
364 CLK_PLL(K210_CLK_PLL0, 0, K210_CLK_IN0),
365 CLK_PLL(K210_CLK_PLL1, 1, K210_CLK_IN0),
366 [K210_CLK_PLL2] = {
367 NAME("pll2")
368 .flags = K210_CLKF_MUX | K210_CLKF_PLL,
369 .mux = MUXIFY(K210_CLK_PLL2),
370 .pll = 2,
Sean Andersonf9c7d4f2020-06-24 06:41:11 -0400371 },
Sean Anderson609bd602021-06-11 00:16:08 -0400372 CLK_MUX(K210_CLK_ACLK, "aclk", MUXIFY(K210_CLK_ACLK),
373 DIVIFY(K210_CLK_ACLK), K210_CLK_GATE_NONE),
374 CLK_FULL(K210_CLK_SPI3, "spi3"),
375 CLK_FULL(K210_CLK_TIMER0, "timer0"),
376 CLK_FULL(K210_CLK_TIMER1, "timer1"),
377 CLK_FULL(K210_CLK_TIMER2, "timer2"),
378 CLK_NOMUX(K210_CLK_SRAM0, "sram0", K210_CLK_ACLK),
379 CLK_NOMUX(K210_CLK_SRAM1, "sram1", K210_CLK_ACLK),
380 CLK_NOMUX(K210_CLK_ROM, "rom", K210_CLK_ACLK),
381 CLK_NOMUX(K210_CLK_DVP, "dvp", K210_CLK_ACLK),
382 CLK_NOMUX(K210_CLK_APB0, "apb0", K210_CLK_ACLK),
383 CLK_NOMUX(K210_CLK_APB1, "apb1", K210_CLK_ACLK),
384 CLK_NOMUX(K210_CLK_APB2, "apb2", K210_CLK_ACLK),
385 CLK_NOMUX(K210_CLK_AI, "ai", K210_CLK_PLL1),
386 CLK_NOMUX(K210_CLK_I2S0, "i2s0", K210_CLK_PLL2),
387 CLK_NOMUX(K210_CLK_I2S1, "i2s1", K210_CLK_PLL2),
388 CLK_NOMUX(K210_CLK_I2S2, "i2s2", K210_CLK_PLL2),
389 CLK_NOMUX(K210_CLK_WDT0, "wdt0", K210_CLK_IN0),
390 CLK_NOMUX(K210_CLK_WDT1, "wdt1", K210_CLK_IN0),
391 CLK_NOMUX(K210_CLK_SPI0, "spi0", K210_CLK_PLL0),
392 CLK_NOMUX(K210_CLK_SPI1, "spi1", K210_CLK_PLL0),
393 CLK_NOMUX(K210_CLK_SPI2, "spi2", K210_CLK_PLL0),
394 CLK_NOMUX(K210_CLK_I2C0, "i2c0", K210_CLK_PLL0),
395 CLK_NOMUX(K210_CLK_I2C1, "i2c1", K210_CLK_PLL0),
396 CLK_NOMUX(K210_CLK_I2C2, "i2c2", K210_CLK_PLL0),
397 CLK_DIV(K210_CLK_I2S0_M, "i2s0_m", K210_CLK_PLL2),
398 CLK_DIV(K210_CLK_I2S1_M, "i2s1_m", K210_CLK_PLL2),
399 CLK_DIV(K210_CLK_I2S2_M, "i2s2_m", K210_CLK_PLL2),
400 CLK_DIV(K210_CLK_CLINT, "clint", K210_CLK_ACLK),
401 CLK_GATE(K210_CLK_CPU, "cpu", K210_CLK_ACLK),
402 CLK_GATE(K210_CLK_DMA, "dma", K210_CLK_ACLK),
403 CLK_GATE(K210_CLK_FFT, "fft", K210_CLK_ACLK),
404 CLK_GATE(K210_CLK_GPIO, "gpio", K210_CLK_APB0),
405 CLK_GATE(K210_CLK_UART1, "uart1", K210_CLK_APB0),
406 CLK_GATE(K210_CLK_UART2, "uart2", K210_CLK_APB0),
407 CLK_GATE(K210_CLK_UART3, "uart3", K210_CLK_APB0),
408 CLK_GATE(K210_CLK_FPIOA, "fpioa", K210_CLK_APB0),
409 CLK_GATE(K210_CLK_SHA, "sha", K210_CLK_APB0),
410 CLK_GATE(K210_CLK_AES, "aes", K210_CLK_APB1),
411 CLK_GATE(K210_CLK_OTP, "otp", K210_CLK_APB1),
412 CLK_GATE(K210_CLK_RTC, "rtc", K210_CLK_IN0),
413#undef NAME
414#undef CLK_PLL
415#undef CLK
416#undef CLK_FULL
417#undef CLK_NOMUX
418#undef CLK_DIV
419#undef CLK_GATE
420#undef CLK_LIST
Sean Andersonf9c7d4f2020-06-24 06:41:11 -0400421};
422
Sean Andersonaf9f9972021-06-11 00:16:09 -0400423#define K210_PLL_CLKR GENMASK(3, 0)
424#define K210_PLL_CLKF GENMASK(9, 4)
425#define K210_PLL_CLKOD GENMASK(13, 10) /* Output Divider */
426#define K210_PLL_BWADJ GENMASK(19, 14) /* BandWidth Adjust */
427#define K210_PLL_RESET BIT(20)
428#define K210_PLL_PWRD BIT(21) /* PoWeReD */
429#define K210_PLL_INTFB BIT(22) /* Internal FeedBack */
430#define K210_PLL_BYPASS BIT(23)
431#define K210_PLL_TEST BIT(24)
432#define K210_PLL_EN BIT(25)
433#define K210_PLL_TEST_EN BIT(26)
434
435#define K210_PLL_LOCK 0
436#define K210_PLL_CLEAR_SLIP 2
437#define K210_PLL_TEST_OUT 3
438
439#ifdef CONFIG_CLK_K210_SET_RATE
440static int k210_pll_enable(struct k210_clk_priv *priv, int id);
441static int k210_pll_disable(struct k210_clk_priv *priv, int id);
442static ulong k210_pll_get_rate(struct k210_clk_priv *priv, int id, ulong rate_in);
443
444/*
445 * The PLL included with the Kendryte K210 appears to be a True Circuits, Inc.
446 * General-Purpose PLL. The logical layout of the PLL with internal feedback is
447 * approximately the following:
448 *
449 * +---------------+
450 * |reference clock|
451 * +---------------+
452 * |
453 * v
454 * +--+
455 * |/r|
456 * +--+
457 * |
458 * v
459 * +-------------+
460 * |divided clock|
461 * +-------------+
462 * |
463 * v
464 * +--------------+
465 * |phase detector|<---+
466 * +--------------+ |
467 * | |
468 * v +--------------+
469 * +---+ |feedback clock|
470 * |VCO| +--------------+
471 * +---+ ^
472 * | +--+ |
473 * +--->|/f|---+
474 * | +--+
475 * v
476 * +---+
477 * |/od|
478 * +---+
479 * |
480 * v
481 * +------+
482 * |output|
483 * +------+
484 *
485 * The k210 PLLs have three factors: r, f, and od. Because of the feedback mode,
486 * the effect of the division by f is to multiply the input frequency. The
487 * equation for the output rate is
488 * rate = (rate_in * f) / (r * od).
489 * Moving knowns to one side of the equation, we get
490 * rate / rate_in = f / (r * od)
491 * Rearranging slightly,
492 * abs_error = abs((rate / rate_in) - (f / (r * od))).
493 * To get relative, error, we divide by the expected ratio
494 * error = abs((rate / rate_in) - (f / (r * od))) / (rate / rate_in).
495 * Simplifying,
496 * error = abs(1 - f / (r * od)) / (rate / rate_in)
497 * error = abs(1 - (f * rate_in) / (r * od * rate))
498 * Using the constants ratio = rate / rate_in and inv_ratio = rate_in / rate,
499 * error = abs((f * inv_ratio) / (r * od) - 1)
500 * This is the error used in evaluating parameters.
501 *
502 * r and od are four bits each, while f is six bits. Because r and od are
503 * multiplied together, instead of the full 256 values possible if both bits
504 * were used fully, there are only 97 distinct products. Combined with f, there
505 * are 6208 theoretical settings for the PLL. However, most of these settings
506 * can be ruled out immediately because they do not have the correct ratio.
507 *
508 * In addition to the constraint of approximating the desired ratio, parameters
509 * must also keep internal pll frequencies within acceptable ranges. The divided
510 * clock's minimum and maximum frequencies have a ratio of around 128. This
511 * leaves fairly substantial room to work with, especially since the only
512 * affected parameter is r. The VCO's minimum and maximum frequency have a ratio
513 * of 5, which is considerably more restrictive.
514 *
515 * The r and od factors are stored in a table. This is to make it easy to find
516 * the next-largest product. Some products have multiple factorizations, but
517 * only when one factor has at least a 2.5x ratio to the factors of the other
518 * factorization. This is because any smaller ratio would not make a difference
519 * when ensuring the VCO's frequency is within spec.
520 *
521 * Throughout the calculation function, fixed point arithmetic is used. Because
522 * the range of rate and rate_in may be up to 1.75 GHz, or around 2^30, 64-bit
523 * 32.32 fixed-point numbers are used to represent ratios. In general, to
524 * implement division, the numerator is first multiplied by 2^32. This gives a
525 * result where the whole number part is in the upper 32 bits, and the fraction
526 * is in the lower 32 bits.
527 *
528 * In general, rounding is done to the closest integer. This helps find the best
529 * approximation for the ratio. Rounding in one direction (e.g down) could cause
530 * the function to miss a better ratio with one of the parameters increased by
531 * one.
532 */
533
534/*
535 * The factors table was generated with the following python code:
536 *
537 * def p(x, y):
538 * return (1.0*x/y > 2.5) or (1.0*y/x > 2.5)
539 *
540 * factors = {}
541 * for i in range(1, 17):
542 * for j in range(1, 17):
543 * fs = factors.get(i*j) or []
544 * if fs == [] or all([
545 * (p(i, x) and p(i, y)) or (p(j, x) and p(j, y))
546 * for (x, y) in fs]):
547 * fs.append((i, j))
548 * factors[i*j] = fs
549 *
550 * for k, l in sorted(factors.items()):
551 * for v in l:
552 * print("PACK(%s, %s)," % v)
553 */
554#define PACK(r, od) (((((r) - 1) & 0xF) << 4) | (((od) - 1) & 0xF))
555#define UNPACK_R(val) ((((val) >> 4) & 0xF) + 1)
556#define UNPACK_OD(val) (((val) & 0xF) + 1)
557static const u8 factors[] = {
558 PACK(1, 1),
559 PACK(1, 2),
560 PACK(1, 3),
561 PACK(1, 4),
562 PACK(1, 5),
563 PACK(1, 6),
564 PACK(1, 7),
565 PACK(1, 8),
566 PACK(1, 9),
567 PACK(3, 3),
568 PACK(1, 10),
569 PACK(1, 11),
570 PACK(1, 12),
571 PACK(3, 4),
572 PACK(1, 13),
573 PACK(1, 14),
574 PACK(1, 15),
575 PACK(3, 5),
576 PACK(1, 16),
577 PACK(4, 4),
578 PACK(2, 9),
579 PACK(2, 10),
580 PACK(3, 7),
581 PACK(2, 11),
582 PACK(2, 12),
583 PACK(5, 5),
584 PACK(2, 13),
585 PACK(3, 9),
586 PACK(2, 14),
587 PACK(2, 15),
588 PACK(2, 16),
589 PACK(3, 11),
590 PACK(5, 7),
591 PACK(3, 12),
592 PACK(3, 13),
593 PACK(4, 10),
594 PACK(3, 14),
595 PACK(4, 11),
596 PACK(3, 15),
597 PACK(3, 16),
598 PACK(7, 7),
599 PACK(5, 10),
600 PACK(4, 13),
601 PACK(6, 9),
602 PACK(5, 11),
603 PACK(4, 14),
604 PACK(4, 15),
605 PACK(7, 9),
606 PACK(4, 16),
607 PACK(5, 13),
608 PACK(6, 11),
609 PACK(5, 14),
610 PACK(6, 12),
611 PACK(5, 15),
612 PACK(7, 11),
613 PACK(6, 13),
614 PACK(5, 16),
615 PACK(9, 9),
616 PACK(6, 14),
617 PACK(8, 11),
618 PACK(6, 15),
619 PACK(7, 13),
620 PACK(6, 16),
621 PACK(7, 14),
622 PACK(9, 11),
623 PACK(10, 10),
624 PACK(8, 13),
625 PACK(7, 15),
626 PACK(9, 12),
627 PACK(10, 11),
628 PACK(7, 16),
629 PACK(9, 13),
630 PACK(8, 15),
631 PACK(11, 11),
632 PACK(9, 14),
633 PACK(8, 16),
634 PACK(10, 13),
635 PACK(11, 12),
636 PACK(9, 15),
637 PACK(10, 14),
638 PACK(11, 13),
639 PACK(9, 16),
640 PACK(10, 15),
641 PACK(11, 14),
642 PACK(12, 13),
643 PACK(10, 16),
644 PACK(11, 15),
645 PACK(12, 14),
646 PACK(13, 13),
647 PACK(11, 16),
648 PACK(12, 15),
649 PACK(13, 14),
650 PACK(12, 16),
651 PACK(13, 15),
652 PACK(14, 14),
653 PACK(13, 16),
654 PACK(14, 15),
655 PACK(14, 16),
656 PACK(15, 15),
657 PACK(15, 16),
658 PACK(16, 16),
659};
660
661TEST_STATIC int k210_pll_calc_config(u32 rate, u32 rate_in,
662 struct k210_pll_config *best)
663{
664 int i;
665 s64 error, best_error;
666 u64 ratio, inv_ratio; /* fixed point 32.32 ratio of the rates */
667 u64 max_r;
668 u64 r, f, od;
669
670 /*
671 * Can't go over 1.75 GHz or under 21.25 MHz due to limitations on the
672 * VCO frequency. These are not the same limits as below because od can
673 * reduce the output frequency by 16.
674 */
675 if (rate > 1750000000 || rate < 21250000)
676 return -EINVAL;
677
678 /* Similar restrictions on the input rate */
679 if (rate_in > 1750000000 || rate_in < 13300000)
680 return -EINVAL;
681
682 ratio = DIV_ROUND_CLOSEST_ULL((u64)rate << 32, rate_in);
683 inv_ratio = DIV_ROUND_CLOSEST_ULL((u64)rate_in << 32, rate);
684 /* Can't increase by more than 64 or reduce by more than 256 */
685 if (rate > rate_in && ratio > (64ULL << 32))
686 return -EINVAL;
687 else if (rate <= rate_in && inv_ratio > (256ULL << 32))
688 return -EINVAL;
689
690 /*
691 * The divided clock (rate_in / r) must stay between 1.75 GHz and 13.3
692 * MHz. There is no minimum, since the only way to get a higher input
693 * clock than 26 MHz is to use a clock generated by a PLL. Because PLLs
694 * cannot output frequencies greater than 1.75 GHz, the minimum would
695 * never be greater than one.
696 */
697 max_r = DIV_ROUND_DOWN_ULL(rate_in, 13300000);
698
699 /* Variables get immediately incremented, so start at -1th iteration */
700 i = -1;
701 f = 0;
702 r = 0;
703 od = 0;
704 best_error = S64_MAX;
705 error = best_error;
706 /* do-while here so we always try at least one ratio */
707 do {
708 /*
709 * Whether we swapped r and od while enforcing frequency limits
710 */
711 bool swapped = false;
Sean Anderson49708742021-09-11 13:20:01 -0400712 /*
713 * Whether the intermediate frequencies are out-of-spec
714 */
715 bool out_of_spec;
Sean Andersonaf9f9972021-06-11 00:16:09 -0400716 u64 last_od = od;
717 u64 last_r = r;
718
719 /*
720 * Try the next largest value for f (or r and od) and
721 * recalculate the other parameters based on that
722 */
723 if (rate > rate_in) {
724 /*
725 * Skip factors of the same product if we already tried
726 * out that product
727 */
728 do {
729 i++;
730 r = UNPACK_R(factors[i]);
731 od = UNPACK_OD(factors[i]);
732 } while (i + 1 < ARRAY_SIZE(factors) &&
733 r * od == last_r * last_od);
734
735 /* Round close */
736 f = (r * od * ratio + BIT(31)) >> 32;
737 if (f > 64)
738 f = 64;
739 } else {
740 u64 tmp = ++f * inv_ratio;
741 bool round_up = !!(tmp & BIT(31));
742 u32 goal = (tmp >> 32) + round_up;
743 u32 err, last_err;
744
745 /* Get the next r/od pair in factors */
746 while (r * od < goal && i + 1 < ARRAY_SIZE(factors)) {
747 i++;
748 r = UNPACK_R(factors[i]);
749 od = UNPACK_OD(factors[i]);
750 }
751
752 /*
753 * This is a case of double rounding. If we rounded up
754 * above, we need to round down (in cases of ties) here.
755 * This prevents off-by-one errors resulting from
756 * choosing X+2 over X when X.Y rounds up to X+1 and
757 * there is no r * od = X+1. For the converse, when X.Y
758 * is rounded down to X, we should choose X+1 over X-1.
759 */
760 err = abs(r * od - goal);
761 last_err = abs(last_r * last_od - goal);
762 if (last_err < err || (round_up && last_err == err)) {
763 i--;
764 r = last_r;
765 od = last_od;
766 }
767 }
768
769 /*
770 * Enforce limits on internal clock frequencies. If we
771 * aren't in spec, try swapping r and od. If everything is
772 * in-spec, calculate the relative error.
773 */
Sean Anderson49708742021-09-11 13:20:01 -0400774again:
775 out_of_spec = false;
776 if (r > max_r) {
777 out_of_spec = true;
778 } else {
Sean Andersonaf9f9972021-06-11 00:16:09 -0400779 /*
Sean Anderson49708742021-09-11 13:20:01 -0400780 * There is no way to only divide once; we need
781 * to examine the frequency with and without the
782 * effect of od.
Sean Andersonaf9f9972021-06-11 00:16:09 -0400783 */
Sean Anderson49708742021-09-11 13:20:01 -0400784 u64 vco = DIV_ROUND_CLOSEST_ULL(rate_in * f, r);
Sean Andersonaf9f9972021-06-11 00:16:09 -0400785
Sean Anderson49708742021-09-11 13:20:01 -0400786 if (vco > 1750000000 || vco < 340000000)
Sean Andersonaf9f9972021-06-11 00:16:09 -0400787 out_of_spec = true;
Sean Anderson49708742021-09-11 13:20:01 -0400788 }
Sean Andersonaf9f9972021-06-11 00:16:09 -0400789
Sean Anderson49708742021-09-11 13:20:01 -0400790 if (out_of_spec) {
791 u64 new_r, new_od;
792
793 if (!swapped) {
794 u64 tmp = r;
795
796 r = od;
797 od = tmp;
798 swapped = true;
799 goto again;
Sean Andersonaf9f9972021-06-11 00:16:09 -0400800 }
801
Sean Anderson49708742021-09-11 13:20:01 -0400802 /*
803 * Try looking ahead to see if there are additional
804 * factors for the same product.
805 */
806 if (i + 1 < ARRAY_SIZE(factors)) {
807 i++;
808 new_r = UNPACK_R(factors[i]);
809 new_od = UNPACK_OD(factors[i]);
810 if (r * od == new_r * new_od) {
811 r = new_r;
812 od = new_od;
813 swapped = false;
814 goto again;
Sean Andersonaf9f9972021-06-11 00:16:09 -0400815 }
Sean Anderson49708742021-09-11 13:20:01 -0400816 i--;
Sean Andersonaf9f9972021-06-11 00:16:09 -0400817 }
818
Sean Anderson425c08f2021-09-11 13:20:03 -0400819 /*
820 * Try looking back to see if there is a worse ratio
821 * that we could try anyway
822 */
823 while (i > 0) {
824 i--;
825 new_r = UNPACK_R(factors[i]);
826 new_od = UNPACK_OD(factors[i]);
827 /*
828 * Don't loop over factors for the same product
829 * to avoid getting stuck because of the above
830 * clause
831 */
832 if (r * od != new_r * new_od) {
833 if (new_r * new_od > last_r * last_od) {
834 r = new_r;
835 od = new_od;
836 swapped = false;
837 goto again;
838 }
839 break;
840 }
841 }
842
Sean Anderson49708742021-09-11 13:20:01 -0400843 /* We ran out of things to try */
844 continue;
845 }
Sean Andersonaf9f9972021-06-11 00:16:09 -0400846
Sean Anderson49708742021-09-11 13:20:01 -0400847 error = DIV_ROUND_CLOSEST_ULL(f * inv_ratio, r * od);
848 /* The lower 16 bits are spurious */
Heinrich Schuchardte77ef0b2022-10-16 18:12:32 +0200849 error = abs64((error - BIT_ULL(32))) >> 16;
Sean Anderson49708742021-09-11 13:20:01 -0400850
851 if (error < best_error) {
852 best->r = r;
853 best->f = f;
854 best->od = od;
855 best_error = error;
Sean Andersonaf9f9972021-06-11 00:16:09 -0400856 }
857 } while (f < 64 && i + 1 < ARRAY_SIZE(factors) && error != 0);
858
Sean Anderson49708742021-09-11 13:20:01 -0400859 log_debug("best error %lld\n", best_error);
Sean Andersonaf9f9972021-06-11 00:16:09 -0400860 if (best_error == S64_MAX)
861 return -EINVAL;
862
Sean Andersonaf9f9972021-06-11 00:16:09 -0400863 return 0;
864}
865
866static ulong k210_pll_set_rate(struct k210_clk_priv *priv, int id, ulong rate,
867 ulong rate_in)
868{
869 int err;
870 const struct k210_pll_params *pll = &k210_plls[id];
871 struct k210_pll_config config = {};
872 u32 reg;
Sean Andersondf79e2b2021-06-11 00:16:12 -0400873 ulong calc_rate;
Sean Andersonaf9f9972021-06-11 00:16:09 -0400874
Sean Andersonaf9f9972021-06-11 00:16:09 -0400875 err = k210_pll_calc_config(rate, rate_in, &config);
876 if (err)
877 return err;
878 log_debug("Got r=%u f=%u od=%u\n", config.r, config.f, config.od);
879
Sean Andersondf79e2b2021-06-11 00:16:12 -0400880 /* Don't bother setting the rate if we're already at that rate */
881 calc_rate = DIV_ROUND_DOWN_ULL(((u64)rate_in) * config.f,
882 config.r * config.od);
883 if (calc_rate == k210_pll_get_rate(priv, id, rate))
884 return calc_rate;
885
Sean Andersonaf9f9972021-06-11 00:16:09 -0400886 k210_pll_disable(priv, id);
887
888 reg = readl(priv->base + pll->off);
889 reg &= ~K210_PLL_CLKR
890 & ~K210_PLL_CLKF
891 & ~K210_PLL_CLKOD
892 & ~K210_PLL_BWADJ;
893 reg |= FIELD_PREP(K210_PLL_CLKR, config.r - 1)
894 | FIELD_PREP(K210_PLL_CLKF, config.f - 1)
895 | FIELD_PREP(K210_PLL_CLKOD, config.od - 1)
896 | FIELD_PREP(K210_PLL_BWADJ, config.f - 1);
897 writel(reg, priv->base + pll->off);
898
Sean Andersondf79e2b2021-06-11 00:16:12 -0400899 k210_pll_enable(priv, id);
Sean Andersonaf9f9972021-06-11 00:16:09 -0400900
901 serial_setbrg();
902 return k210_pll_get_rate(priv, id, rate);
903}
904#else
905static ulong k210_pll_set_rate(struct k210_clk_priv *priv, int id, ulong rate,
906 ulong rate_in)
907{
908 return -ENOSYS;
909}
910#endif /* CONFIG_CLK_K210_SET_RATE */
911
912static ulong k210_pll_get_rate(struct k210_clk_priv *priv, int id,
913 ulong rate_in)
914{
915 u64 r, f, od;
916 u32 reg = readl(priv->base + k210_plls[id].off);
917
Sean Anderson54d5d2d2021-09-11 13:20:00 -0400918 if (reg & K210_PLL_BYPASS)
Sean Andersonaf9f9972021-06-11 00:16:09 -0400919 return rate_in;
920
921 if (!(reg & K210_PLL_PWRD))
922 return 0;
923
924 r = FIELD_GET(K210_PLL_CLKR, reg) + 1;
925 f = FIELD_GET(K210_PLL_CLKF, reg) + 1;
926 od = FIELD_GET(K210_PLL_CLKOD, reg) + 1;
927
928 return DIV_ROUND_DOWN_ULL(((u64)rate_in) * f, r * od);
929}
930
931/*
932 * Wait for the PLL to be locked. If the PLL is not locked, try clearing the
933 * slip before retrying
934 */
935static void k210_pll_waitfor_lock(struct k210_clk_priv *priv, int id)
936{
937 const struct k210_pll_params *pll = &k210_plls[id];
938 u32 mask = (BIT(pll->width) - 1) << pll->shift;
939
940 while (true) {
941 u32 reg = readl(priv->base + K210_SYSCTL_PLL_LOCK);
942
943 if ((reg & mask) == mask)
944 break;
945
946 reg |= BIT(pll->shift + K210_PLL_CLEAR_SLIP);
947 writel(reg, priv->base + K210_SYSCTL_PLL_LOCK);
948 }
949}
950
Sean Anderson612a8332021-06-11 00:16:10 -0400951static bool k210_pll_enabled(u32 reg)
952{
953 return (reg & K210_PLL_PWRD) && (reg & K210_PLL_EN) &&
954 !(reg & K210_PLL_RESET);
955}
956
Sean Andersonaf9f9972021-06-11 00:16:09 -0400957/* Adapted from sysctl_pll_enable */
958static int k210_pll_enable(struct k210_clk_priv *priv, int id)
959{
960 const struct k210_pll_params *pll = &k210_plls[id];
961 u32 reg = readl(priv->base + pll->off);
962
Sean Anderson612a8332021-06-11 00:16:10 -0400963 if (k210_pll_enabled(reg))
Sean Andersonaf9f9972021-06-11 00:16:09 -0400964 return 0;
965
966 reg |= K210_PLL_PWRD;
967 writel(reg, priv->base + pll->off);
968
969 /* Ensure reset is low before asserting it */
970 reg &= ~K210_PLL_RESET;
971 writel(reg, priv->base + pll->off);
972 reg |= K210_PLL_RESET;
973 writel(reg, priv->base + pll->off);
974 nop();
975 nop();
976 reg &= ~K210_PLL_RESET;
977 writel(reg, priv->base + pll->off);
978
979 k210_pll_waitfor_lock(priv, id);
980
981 reg &= ~K210_PLL_BYPASS;
982 reg |= K210_PLL_EN;
983 writel(reg, priv->base + pll->off);
984
985 return 0;
986}
987
988static int k210_pll_disable(struct k210_clk_priv *priv, int id)
989{
990 const struct k210_pll_params *pll = &k210_plls[id];
991 u32 reg = readl(priv->base + pll->off);
992
993 /*
994 * Bypassing before powering off is important so child clocks don't stop
995 * working. This is especially important for pll0, the indirect parent
996 * of the cpu clock.
997 */
998 reg |= K210_PLL_BYPASS;
999 writel(reg, priv->base + pll->off);
1000
1001 reg &= ~K210_PLL_PWRD;
1002 reg &= ~K210_PLL_EN;
1003 writel(reg, priv->base + pll->off);
1004 return 0;
1005}
1006
Sean Anderson609bd602021-06-11 00:16:08 -04001007static u32 k210_clk_readl(struct k210_clk_priv *priv, u8 off, u8 shift,
1008 u8 width)
Sean Andersonf9c7d4f2020-06-24 06:41:11 -04001009{
Sean Anderson609bd602021-06-11 00:16:08 -04001010 u32 reg = readl(priv->base + off);
Sean Andersonf9c7d4f2020-06-24 06:41:11 -04001011
Sean Anderson609bd602021-06-11 00:16:08 -04001012 return (reg >> shift) & (BIT(width) - 1);
Sean Andersonf9c7d4f2020-06-24 06:41:11 -04001013}
1014
Sean Anderson609bd602021-06-11 00:16:08 -04001015static void k210_clk_writel(struct k210_clk_priv *priv, u8 off, u8 shift,
1016 u8 width, u32 val)
Sean Andersonf9c7d4f2020-06-24 06:41:11 -04001017{
Sean Anderson609bd602021-06-11 00:16:08 -04001018 u32 reg = readl(priv->base + off);
1019 u32 mask = (BIT(width) - 1) << shift;
Sean Andersonf9c7d4f2020-06-24 06:41:11 -04001020
Sean Anderson609bd602021-06-11 00:16:08 -04001021 reg &= ~mask;
1022 reg |= mask & (val << shift);
1023 writel(reg, priv->base + off);
Sean Andersonf9c7d4f2020-06-24 06:41:11 -04001024}
1025
Sean Anderson609bd602021-06-11 00:16:08 -04001026static int k210_clk_get_parent(struct k210_clk_priv *priv, int id)
Sean Andersonf9c7d4f2020-06-24 06:41:11 -04001027{
Sean Anderson609bd602021-06-11 00:16:08 -04001028 u32 sel;
1029 const struct k210_mux_params *mux;
Sean Andersonf9c7d4f2020-06-24 06:41:11 -04001030
Sean Anderson609bd602021-06-11 00:16:08 -04001031 if (!(k210_clks[id].flags & K210_CLKF_MUX))
1032 return k210_clks[id].parent;
1033 mux = &k210_muxes[k210_clks[id].mux];
Sean Andersonf9c7d4f2020-06-24 06:41:11 -04001034
Sean Anderson609bd602021-06-11 00:16:08 -04001035 sel = k210_clk_readl(priv, mux->off, mux->shift, mux->width);
1036 assert(sel < mux->num_parents);
1037 return mux->parents[sel];
Sean Andersonf9c7d4f2020-06-24 06:41:11 -04001038}
1039
Sean Anderson609bd602021-06-11 00:16:08 -04001040static ulong do_k210_clk_get_rate(struct k210_clk_priv *priv, int id)
Sean Andersonf9c7d4f2020-06-24 06:41:11 -04001041{
Sean Anderson609bd602021-06-11 00:16:08 -04001042 int parent;
1043 u32 val;
1044 ulong parent_rate;
1045 const struct k210_div_params *div;
Sean Andersonf9c7d4f2020-06-24 06:41:11 -04001046
Sean Anderson609bd602021-06-11 00:16:08 -04001047 if (id == K210_CLK_IN0)
1048 return clk_get_rate(&priv->in0);
Sean Andersonf9c7d4f2020-06-24 06:41:11 -04001049
Sean Anderson609bd602021-06-11 00:16:08 -04001050 parent = k210_clk_get_parent(priv, id);
1051 parent_rate = do_k210_clk_get_rate(priv, parent);
Sean Anderson54d5d2d2021-09-11 13:20:00 -04001052 if (IS_ERR_VALUE(parent_rate))
1053 return parent_rate;
Sean Andersonf9c7d4f2020-06-24 06:41:11 -04001054
Sean Anderson609bd602021-06-11 00:16:08 -04001055 if (k210_clks[id].flags & K210_CLKF_PLL)
1056 return k210_pll_get_rate(priv, k210_clks[id].pll, parent_rate);
1057
1058 if (k210_clks[id].div == K210_CLK_DIV_NONE)
1059 return parent_rate;
1060 div = &k210_divs[k210_clks[id].div];
1061
1062 if (div->type == K210_DIV_FIXED)
1063 return parent_rate / div->div;
1064
1065 val = k210_clk_readl(priv, div->off, div->shift, div->width);
1066 switch (div->type) {
1067 case K210_DIV_ONE:
1068 return parent_rate / (val + 1);
1069 case K210_DIV_EVEN:
1070 return parent_rate / 2 / (val + 1);
1071 case K210_DIV_POWER:
1072 /* This is ACLK, which has no divider on IN0 */
1073 if (parent == K210_CLK_IN0)
1074 return parent_rate;
1075 return parent_rate / (2 << val);
1076 default:
1077 assert(false);
1078 return -EINVAL;
1079 };
Sean Andersonf9c7d4f2020-06-24 06:41:11 -04001080}
1081
Sean Anderson609bd602021-06-11 00:16:08 -04001082static ulong k210_clk_get_rate(struct clk *clk)
Sean Andersonf9c7d4f2020-06-24 06:41:11 -04001083{
Sean Anderson609bd602021-06-11 00:16:08 -04001084 return do_k210_clk_get_rate(dev_get_priv(clk->dev), clk->id);
1085}
Sean Andersonf9c7d4f2020-06-24 06:41:11 -04001086
Sean Anderson609bd602021-06-11 00:16:08 -04001087static int do_k210_clk_set_parent(struct k210_clk_priv *priv, int id, int new)
1088{
1089 int i;
1090 const struct k210_mux_params *mux;
Sean Andersonf9c7d4f2020-06-24 06:41:11 -04001091
Sean Anderson609bd602021-06-11 00:16:08 -04001092 if (!(k210_clks[id].flags & K210_CLKF_MUX))
1093 return -ENOSYS;
1094 mux = &k210_muxes[k210_clks[id].mux];
1095
1096 for (i = 0; i < mux->num_parents; i++) {
1097 if (mux->parents[i] == new) {
1098 k210_clk_writel(priv, mux->off, mux->shift, mux->width,
1099 i);
1100 return 0;
1101 }
1102 }
1103 return -EINVAL;
1104}
1105
1106static int k210_clk_set_parent(struct clk *clk, struct clk *parent)
1107{
1108 return do_k210_clk_set_parent(dev_get_priv(clk->dev), clk->id,
1109 parent->id);
1110}
1111
Sean Anderson29e30672021-06-11 00:16:11 -04001112static ulong k210_clk_set_rate(struct clk *clk, unsigned long rate)
1113{
1114 int parent, ret, err;
1115 ulong rate_in, val;
1116 const struct k210_div_params *div;
1117 struct k210_clk_priv *priv = dev_get_priv(clk->dev);
1118
1119 if (clk->id == K210_CLK_IN0)
1120 return clk_set_rate(&priv->in0, rate);
1121
1122 parent = k210_clk_get_parent(priv, clk->id);
1123 rate_in = do_k210_clk_get_rate(priv, parent);
Sean Anderson54d5d2d2021-09-11 13:20:00 -04001124 if (IS_ERR_VALUE(rate_in))
1125 return rate_in;
Sean Anderson29e30672021-06-11 00:16:11 -04001126
1127 log_debug("id=%ld rate=%lu rate_in=%lu\n", clk->id, rate, rate_in);
1128
1129 if (clk->id == K210_CLK_PLL0) {
1130 /* Bypass ACLK so the CPU keeps going */
1131 ret = do_k210_clk_set_parent(priv, K210_CLK_ACLK, K210_CLK_IN0);
1132 if (ret)
1133 return ret;
1134 } else if (clk->id == K210_CLK_PLL1 && gd->flags & GD_FLG_RELOC) {
1135 /*
1136 * We can't bypass the AI clock like we can ACLK, and after
1137 * relocation we are using the AI ram.
1138 */
1139 return -EPERM;
1140 }
1141
1142 if (k210_clks[clk->id].flags & K210_CLKF_PLL) {
1143 ret = k210_pll_set_rate(priv, k210_clks[clk->id].pll, rate,
1144 rate_in);
1145 if (!IS_ERR_VALUE(ret) && clk->id == K210_CLK_PLL0) {
1146 /*
1147 * This may have the side effect of reparenting ACLK,
1148 * but I don't really want to keep track of what the old
1149 * parent was.
1150 */
1151 err = do_k210_clk_set_parent(priv, K210_CLK_ACLK,
1152 K210_CLK_PLL0);
1153 if (err)
1154 return err;
1155 }
1156 return ret;
1157 }
1158
1159 if (k210_clks[clk->id].div == K210_CLK_DIV_NONE)
1160 return -ENOSYS;
1161 div = &k210_divs[k210_clks[clk->id].div];
1162
1163 switch (div->type) {
1164 case K210_DIV_ONE:
1165 val = DIV_ROUND_CLOSEST_ULL((u64)rate_in, rate);
1166 val = val ? val - 1 : 0;
1167 break;
1168 case K210_DIV_EVEN:
1169 val = DIV_ROUND_CLOSEST_ULL((u64)rate_in, 2 * rate);
1170 break;
1171 case K210_DIV_POWER:
1172 /* This is ACLK, which has no divider on IN0 */
1173 if (parent == K210_CLK_IN0)
1174 return -ENOSYS;
1175
1176 val = DIV_ROUND_CLOSEST_ULL((u64)rate_in, rate);
1177 val = __ffs(val);
1178 break;
1179 default:
1180 assert(false);
1181 return -EINVAL;
1182 };
1183
1184 val = val ? val - 1 : 0;
1185 k210_clk_writel(priv, div->off, div->shift, div->width, val);
1186 return do_k210_clk_get_rate(priv, clk->id);
1187}
1188
Sean Anderson609bd602021-06-11 00:16:08 -04001189static int k210_clk_endisable(struct k210_clk_priv *priv, int id, bool enable)
1190{
1191 int parent = k210_clk_get_parent(priv, id);
1192 const struct k210_gate_params *gate;
1193
1194 if (id == K210_CLK_IN0) {
1195 if (enable)
1196 return clk_enable(&priv->in0);
1197 else
1198 return clk_disable(&priv->in0);
Sean Andersonf9c7d4f2020-06-24 06:41:11 -04001199 }
1200
Sean Anderson609bd602021-06-11 00:16:08 -04001201 /* Only recursively enable clocks since we don't track refcounts */
1202 if (enable) {
1203 int ret = k210_clk_endisable(priv, parent, true);
1204
1205 if (ret && ret != -ENOSYS)
1206 return ret;
Sean Andersonf9c7d4f2020-06-24 06:41:11 -04001207 }
1208
Sean Anderson609bd602021-06-11 00:16:08 -04001209 if (k210_clks[id].flags & K210_CLKF_PLL) {
1210 if (enable)
1211 return k210_pll_enable(priv, k210_clks[id].pll);
1212 else
1213 return k210_pll_disable(priv, k210_clks[id].pll);
Sean Andersonf9c7d4f2020-06-24 06:41:11 -04001214 }
1215
Sean Anderson609bd602021-06-11 00:16:08 -04001216 if (k210_clks[id].gate == K210_CLK_GATE_NONE)
1217 return -ENOSYS;
1218 gate = &k210_gates[k210_clks[id].gate];
Sean Andersonf9c7d4f2020-06-24 06:41:11 -04001219
Sean Anderson609bd602021-06-11 00:16:08 -04001220 k210_clk_writel(priv, gate->off, gate->bit_idx, 1, enable);
Sean Anderson09ad08f2021-04-08 22:13:08 -04001221 return 0;
1222}
Sean Andersonf9c7d4f2020-06-24 06:41:11 -04001223
Sean Anderson609bd602021-06-11 00:16:08 -04001224static int k210_clk_enable(struct clk *clk)
1225{
1226 return k210_clk_endisable(dev_get_priv(clk->dev), clk->id, true);
1227}
1228
1229static int k210_clk_disable(struct clk *clk)
1230{
1231 return k210_clk_endisable(dev_get_priv(clk->dev), clk->id, false);
1232}
1233
1234static int k210_clk_request(struct clk *clk)
1235{
1236 if (clk->id >= ARRAY_SIZE(k210_clks))
1237 return -EINVAL;
1238 return 0;
1239}
1240
1241static const struct clk_ops k210_clk_ops = {
1242 .request = k210_clk_request,
1243 .set_rate = k210_clk_set_rate,
1244 .get_rate = k210_clk_get_rate,
1245 .set_parent = k210_clk_set_parent,
1246 .enable = k210_clk_enable,
1247 .disable = k210_clk_disable,
1248};
1249
Sean Andersonf9c7d4f2020-06-24 06:41:11 -04001250static int k210_clk_probe(struct udevice *dev)
1251{
1252 int ret;
Sean Anderson609bd602021-06-11 00:16:08 -04001253 struct k210_clk_priv *priv = dev_get_priv(dev);
Sean Andersonf9c7d4f2020-06-24 06:41:11 -04001254
Sean Anderson609bd602021-06-11 00:16:08 -04001255 priv->base = dev_read_addr_ptr(dev_get_parent(dev));
1256 if (!priv->base)
Simon Glass9042bf62021-03-25 10:26:08 +13001257 return -EINVAL;
Sean Andersonf9c7d4f2020-06-24 06:41:11 -04001258
Sean Anderson609bd602021-06-11 00:16:08 -04001259 ret = clk_get_by_index(dev, 0, &priv->in0);
Sean Andersonf9c7d4f2020-06-24 06:41:11 -04001260 if (ret)
1261 return ret;
Sean Andersona952c3a2020-09-28 10:52:27 -04001262
Sean Anderson29e30672021-06-11 00:16:11 -04001263 /*
1264 * Force setting defaults, even before relocation. This is so we can
1265 * set the clock rate for PLL1 before we relocate into aisram.
1266 */
1267 if (!(gd->flags & GD_FLG_RELOC))
1268 clk_set_defaults(dev, CLK_DEFAULTS_POST_FORCE);
1269
Sean Andersonf9c7d4f2020-06-24 06:41:11 -04001270 return 0;
1271}
1272
1273static const struct udevice_id k210_clk_ids[] = {
Damien Le Moalfd426b32022-03-01 10:35:39 +00001274 { .compatible = "canaan,k210-clk" },
Sean Andersonf9c7d4f2020-06-24 06:41:11 -04001275 { },
1276};
1277
1278U_BOOT_DRIVER(k210_clk) = {
1279 .name = "k210_clk",
1280 .id = UCLASS_CLK,
1281 .of_match = k210_clk_ids,
1282 .ops = &k210_clk_ops,
Sean Andersonf9c7d4f2020-06-24 06:41:11 -04001283 .probe = k210_clk_probe,
Sean Anderson609bd602021-06-11 00:16:08 -04001284 .priv_auto = sizeof(struct k210_clk_priv),
Sean Andersonf9c7d4f2020-06-24 06:41:11 -04001285};
Sean Anderson612a8332021-06-11 00:16:10 -04001286
Simon Glass8dd86202023-02-05 15:36:26 -07001287#if IS_ENABLED(CONFIG_CMD_CLK)
Sean Anderson612a8332021-06-11 00:16:10 -04001288static char show_enabled(struct k210_clk_priv *priv, int id)
1289{
1290 bool enabled;
1291
1292 if (k210_clks[id].flags & K210_CLKF_PLL) {
1293 const struct k210_pll_params *pll =
1294 &k210_plls[k210_clks[id].pll];
1295
1296 enabled = k210_pll_enabled(readl(priv->base + pll->off));
1297 } else if (k210_clks[id].gate == K210_CLK_GATE_NONE) {
1298 return '-';
1299 } else {
1300 const struct k210_gate_params *gate =
1301 &k210_gates[k210_clks[id].gate];
1302
1303 enabled = k210_clk_readl(priv, gate->off, gate->bit_idx, 1);
1304 }
1305
1306 return enabled ? 'y' : 'n';
1307}
1308
1309static void show_clks(struct k210_clk_priv *priv, int id, int depth)
1310{
1311 int i;
1312
1313 for (i = 0; i < ARRAY_SIZE(k210_clks); i++) {
1314 if (k210_clk_get_parent(priv, i) != id)
1315 continue;
1316
1317 printf(" %-9lu %-7c %*s%s\n", do_k210_clk_get_rate(priv, i),
1318 show_enabled(priv, i), depth * 4, "",
1319 k210_clks[i].name);
1320
1321 show_clks(priv, i, depth + 1);
1322 }
1323}
1324
1325int soc_clk_dump(void)
1326{
1327 int ret;
1328 struct udevice *dev;
1329 struct k210_clk_priv *priv;
1330
1331 ret = uclass_get_device_by_driver(UCLASS_CLK, DM_DRIVER_GET(k210_clk),
1332 &dev);
1333 if (ret)
1334 return ret;
1335 priv = dev_get_priv(dev);
1336
1337 puts(" Rate Enabled Name\n");
1338 puts("------------------------\n");
1339 printf(" %-9lu %-7c %*s%s\n", clk_get_rate(&priv->in0), 'y', 0, "",
1340 priv->in0.dev->name);
1341 show_clks(priv, K210_CLK_IN0, 1);
1342 return 0;
1343}
1344#endif