include/configs/c2mon.h

/*
 * (C) Copyright 2001-2005
 * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
 *
 * See file CREDITS for list of people who contributed to this
 * project.
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License as
 * published by the Free Software Foundation; either version 2 of
 * the License, or (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software
 * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
 * MA 02111-1307 USA
 */

/*
 * board/config.h - configuration options, board specific
 */

#ifndef __CONFIG_H
#define __CONFIG_H

/*
 * High Level Configuration Options
 * (easy to change)
 */

#define CONFIG_MPC855		1	/* This is a MPC855 CPU		*/
#define CONFIG_C2MON		1	/* ...on a C2MON module		*/

#define CONFIG_80MHz		1	/* Running at 5 * 16 = 80 MHz	*/

#define	CONFIG_8xx_CONS_SMC1	1	/* Console is on SMC1		*/
#undef	CONFIG_8xx_CONS_SMC2
#undef	CONFIG_8xx_CONS_NONE
#define CONFIG_BAUDRATE		115200	/* console baudrate = 115kbps	*/
#if 0
#define CONFIG_BOOTDELAY	-1	/* autoboot disabled		*/
#else
#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
#endif

#define	CONFIG_CLOCKS_IN_MHZ	1	/* clocks passsed to Linux in MHz */

#define CONFIG_PREBOOT	"echo;echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;echo"

#undef	CONFIG_BOOTARGS
#define CONFIG_BOOTCOMMAND							\
	"bootp; "								\
	"setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} "	\
	"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; "	\
	"bootm"

#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
#undef	CFG_LOADS_BAUD_CHANGE		/* don't allow baudrate change	*/

#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/

#undef	CONFIG_STATUS_LED		/* Status LED disabled		*/

#undef	CONFIG_CAN_DRIVER		/* CAN Driver support disabled	*/

/*
 * BOOTP options
 */
#define CONFIG_BOOTP_SUBNETMASK
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_BOOTFILESIZE


#define CONFIG_MAC_PARTITION
#define CONFIG_DOS_PARTITION

#define CONFIG_FEC_ENET		1	/* Use Fast Ethernet Controller	*/

#define	CONFIG_RTC_MPC8xx		/* use internal RTC of MPC8xx	*/


/*
 * Command line configuration.
 */
#include <config_cmd_default.h>

#define CONFIG_CMD_DATE
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_IDE
#define CONFIG_CMD_NFS
#define CONFIG_CMD_SNTP


/*
 * Miscellaneous configurable options
 */
#define	CFG_LONGHELP			/* undef to save memory		*/
#define	CFG_PROMPT		"=> "	/* Monitor Command Prompt	*/

#undef	CFG_HUSH_PARSER			/* use "hush" command parser	*/
#ifdef	CFG_HUSH_PARSER
#define	CFG_PROMPT_HUSH_PS2	"> "
#endif

#if defined(CONFIG_CMD_KGDB)
#define	CFG_CBSIZE		1024	/* Console I/O Buffer Size	*/
#else
#define	CFG_CBSIZE		256	/* Console I/O Buffer Size	*/
#endif
#define	CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
#define	CFG_MAXARGS		16	/* max number of command args	*/
#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/

#define CFG_MEMTEST_START	0x0400000	/* memtest works on	*/
#define CFG_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/

#define	CFG_LOAD_ADDR		0x100000	/* default load address	*/

#define	CFG_HZ			1000	/* decrementer freq: 1 ms ticks	*/

#define CFG_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }

/*
 * Low Level Configuration Settings
 * (address mappings, register initial values, etc.)
 * You should know what you are doing if you make changes here.
 */
/*-----------------------------------------------------------------------
 * Internal Memory Mapped Register
 */
#define CFG_IMMR		0xFFF00000

/*-----------------------------------------------------------------------
 * Definitions for initial stack pointer and data area (in DPRAM)
 */
#define CFG_INIT_RAM_ADDR	CFG_IMMR
#define	CFG_INIT_RAM_END	0x2F00	/* End of used area in DPRAM	*/
#define	CFG_GBL_DATA_SIZE	64  /* size in bytes reserved for initial data */
#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
#define	CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET

/*-----------------------------------------------------------------------
 * Start addresses for the final memory configuration
 * (Set up by the startup code)
 * Please note that CFG_SDRAM_BASE _must_ start at 0
 */
#define	CFG_SDRAM_BASE		0x00000000
#define CFG_FLASH_BASE		0x40000000
#if defined(DEBUG)
#define	CFG_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
#else
#define	CFG_MONITOR_LEN		(192 << 10)	/* Reserve 192 kB for Monitor	*/
#endif
#define CFG_MONITOR_BASE	CFG_FLASH_BASE
#define	CFG_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()	*/

/*
 * For booting Linux, the board info and command line data
 * have to be in the first 8 MB of memory, since this is
 * the maximum mapped by the Linux kernel during initialization.
 */
#define	CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux	*/

/*-----------------------------------------------------------------------
 * FLASH organization
 */
#define CFG_MAX_FLASH_BANKS	2	/* max number of memory banks		*/
#define CFG_MAX_FLASH_SECT	67	/* max number of sectors on one chip	*/

#define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
#define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/

#define	CONFIG_ENV_IS_IN_FLASH	1
#define	CONFIG_ENV_OFFSET		0x8000	/*   Offset   of Environment Sector	*/
#define	CONFIG_ENV_SIZE		0x4000	/* Total Size of Environment Sector	*/

/*-----------------------------------------------------------------------
 * Cache Configuration
 */
#define CFG_CACHELINE_SIZE	16	/* For all MPC8xx CPUs			*/
#if defined(CONFIG_CMD_KGDB)
#define CFG_CACHELINE_SHIFT	4	/* log base 2 of the above value	*/
#endif

/*-----------------------------------------------------------------------
 * SYPCR - System Protection Control				11-9
 * SYPCR can only be written once after reset!
 *-----------------------------------------------------------------------
 * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
 */
#if defined(CONFIG_WATCHDOG)
#define CFG_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
			 SYPCR_SWE  | SYPCR_SWRI| SYPCR_SWP)
#else
#define CFG_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
#endif

/*-----------------------------------------------------------------------
 * SIUMCR - SIU Module Configuration				11-6
 *-----------------------------------------------------------------------
 * PCMCIA config., multi-function pin tri-state
 */
#ifndef	CONFIG_CAN_DRIVER
#define CFG_SIUMCR	(SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
#else	/* we must activate GPL5 in the SIUMCR for CAN */
#define CFG_SIUMCR	(SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
#endif	/* CONFIG_CAN_DRIVER */

/*-----------------------------------------------------------------------
 * TBSCR - Time Base Status and Control				11-26
 *-----------------------------------------------------------------------
 * Clear Reference Interrupt Status, Timebase freezing enabled
 */
#define CFG_TBSCR	(TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)

/*-----------------------------------------------------------------------
 * RTCSC - Real-Time Clock Status and Control Register		11-27
 *-----------------------------------------------------------------------
 */
#define CFG_RTCSC	(RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)

/*-----------------------------------------------------------------------
 * PISCR - Periodic Interrupt Status and Control		11-31
 *-----------------------------------------------------------------------
 * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
 */
#define CFG_PISCR	(PISCR_PS | PISCR_PITF)

/*-----------------------------------------------------------------------
 * PLPRCR - PLL, Low-Power, and Reset Control Register		15-30
 *-----------------------------------------------------------------------
 * Reset PLL lock status sticky bit, timer expired status bit and timer
 * interrupt status bit
 *
 * If this is a 80 MHz CPU, set PLL multiplication factor to 5 (5*16=80)!
 */
#ifdef	CONFIG_80MHz	/* for 80 MHz, we use a 16 MHz clock * 5 */
#define CFG_PLPRCR							\
		( (5-1)<<PLPRCR_MF_SHIFT | PLPRCR_TEXPS | PLPRCR_TMIST )
#else			/* up to 50 MHz we use a 1:1 clock */
#define CFG_PLPRCR	(PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
#endif	/* CONFIG_80MHz */

/*-----------------------------------------------------------------------
 * SCCR - System Clock and reset Control Register		15-27
 *-----------------------------------------------------------------------
 * Set clock output, timebase and RTC source and divider,
 * power management and some other internal clocks
 */
#define SCCR_MASK	SCCR_EBDF11
#ifdef	CONFIG_80MHz	/* for 80 MHz, we use a 16 MHz clock * 5 */
#define CFG_SCCR	(/* SCCR_TBS  | */ \
			 SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
			 SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
			 SCCR_DFALCD00)
#else			/* up to 50 MHz we use a 1:1 clock */
#define CFG_SCCR	(SCCR_TBS     | \
			 SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
			 SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
			 SCCR_DFALCD00)
#endif	/* CONFIG_80MHz */

/*-----------------------------------------------------------------------
 * PCMCIA stuff
 *-----------------------------------------------------------------------
 *
 */
#define CFG_PCMCIA_MEM_ADDR	(0xE0000000)
#define CFG_PCMCIA_MEM_SIZE	( 64 << 20 )
#define CFG_PCMCIA_DMA_ADDR	(0xE4000000)
#define CFG_PCMCIA_DMA_SIZE	( 64 << 20 )
#define CFG_PCMCIA_ATTRB_ADDR	(0xE8000000)
#define CFG_PCMCIA_ATTRB_SIZE	( 64 << 20 )
#define CFG_PCMCIA_IO_ADDR	(0xEC000000)
#define CFG_PCMCIA_IO_SIZE	( 64 << 20 )

/*-----------------------------------------------------------------------
 * PCMCIA Power Switch
 *
 * The C2MON uses a TPS2211A PC-Card Power-Interface Switch to
 * control the voltages on the PCMCIA slot which is connected
 * to Port C (all outputs) and Port B (Over-Current Input)
 *-----------------------------------------------------------------------
 */
			/* Output pins */
#define TPS2211_VCCD0	0x0002		/* PC.14 */
#define TPS2211_VCCD1	0x0004		/* PC.13 */
#define TPS2211_VPPD0	0x0008		/* PC.12 */
#define TPS2211_VPPD1	0x0010		/* PC.11 */
#define TPS2211_OUTPUTS ( TPS2211_VCCD0 | TPS2211_VCCD1 | \
			  TPS2211_VPPD0 | TPS2211_VPPD1 )

			/* Input pins */
#define TPS2211_OC	0x00000200	/* PB.22: Over-Current		*/
#define TPS2211_INPUTS	( TPS2211_OC )

/*-----------------------------------------------------------------------
 * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
 *-----------------------------------------------------------------------
 */

#define	CONFIG_IDE_8xx_PCCARD	1	/* Use IDE with PC Card	Adapter	*/

#undef	CONFIG_IDE_8xx_DIRECT		/* Direct IDE    not supported	*/
#undef	CONFIG_IDE_LED			/* LED   for ide not supported	*/
#undef	CONFIG_IDE_RESET		/* reset for ide not supported	*/

#define CFG_IDE_MAXBUS		1	/* max. 1 IDE bus		*/
#define CFG_IDE_MAXDEVICE	1	/* max. 1 drive per IDE bus	*/

#define CFG_ATA_IDE0_OFFSET	0x0000

#define CFG_ATA_BASE_ADDR	CFG_PCMCIA_MEM_ADDR

/* Offset for data I/O			*/
#define CFG_ATA_DATA_OFFSET	(CFG_PCMCIA_MEM_SIZE + 0x320)

/* Offset for normal register accesses	*/
#define CFG_ATA_REG_OFFSET	(2 * CFG_PCMCIA_MEM_SIZE + 0x320)

/* Offset for alternate registers	*/
#define CFG_ATA_ALT_OFFSET	0x0100


/*-----------------------------------------------------------------------
 *
 *-----------------------------------------------------------------------
 *
 */
#define CFG_DER	0

/*
 * Init Memory Controller:
 *
 * BR0/1 and OR0/1 (FLASH)
 */

#define FLASH_BASE0_PRELIM	0x40000000	/* FLASH bank #0	*/
#define FLASH_BASE1_PRELIM	0x60000000	/* FLASH bank #0	*/

/* used to re-map FLASH both when starting from SRAM or FLASH:
 * restrict access enough to keep SRAM working (if any)
 * but not too much to meddle with FLASH accesses
 */
#define CFG_REMAP_OR_AM		0x80000000	/* OR addr mask */
#define CFG_PRELIM_OR_AM	0xE0000000	/* OR addr mask */

/* FLASH timing: ACS = 11, TRLX = 0, CSNT = 1, SCY = 5, EHTR = 1	*/
#define CFG_OR_TIMING_FLASH	(OR_CSNT_SAM  | OR_ACS_DIV2 | OR_BI | \
				 OR_SCY_5_CLK | OR_EHTR)

#define CFG_OR0_REMAP	(CFG_REMAP_OR_AM  | CFG_OR_TIMING_FLASH)
#define CFG_OR0_PRELIM	(CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH)
#define CFG_BR0_PRELIM	((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V )

#define CFG_OR1_REMAP	CFG_OR0_REMAP
#define CFG_OR1_PRELIM	CFG_OR0_PRELIM
#define CFG_BR1_PRELIM	((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_V )

/*
 * BR2/3 and OR2/3 (SDRAM)
 *
 */
#define SDRAM_BASE2_PRELIM	0x00000000	/* SDRAM bank #0	*/
#define SDRAM_BASE3_PRELIM	0x20000000	/* SDRAM bank #1	*/
#define	SDRAM_MAX_SIZE		0x04000000	/* max 64 MB per bank	*/

/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care)	*/
#define CFG_OR_TIMING_SDRAM	0x00000A00

#define CFG_OR2_PRELIM	(CFG_PRELIM_OR_AM | CFG_OR_TIMING_SDRAM )
#define CFG_BR2_PRELIM	((SDRAM_BASE2_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )

#ifndef	CONFIG_CAN_DRIVER
#define	CFG_OR3_PRELIM	CFG_OR2_PRELIM
#define CFG_BR3_PRELIM	((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
#else	/* CAN uses CS3#, so we can have only one SDRAM bank anyway */
#define	CFG_CAN_BASE		0xC0000000	/* CAN mapped at 0xC0000000	*/
#define CFG_CAN_OR_AM		0xFFFF8000	/* 32 kB address mask		*/
#define CFG_OR3_CAN		(CFG_CAN_OR_AM | OR_G5LA | OR_BI)
#define CFG_BR3_CAN		((CFG_CAN_BASE & BR_BA_MSK) | \
					BR_PS_8 | BR_MS_UPMB | BR_V )
#endif	/* CONFIG_CAN_DRIVER */

/*
 * Memory Periodic Timer Prescaler
 */

/* periodic timer for refresh */
#define CFG_MAMR_PTA	97		/* start with divider for 100 MHz	*/

/* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit	*/
#define CFG_MPTPR_2BK_4K	MPTPR_PTP_DIV16		/* setting for 2 banks	*/
#define CFG_MPTPR_1BK_4K	MPTPR_PTP_DIV32		/* setting for 1 bank	*/

/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit		*/
#define CFG_MPTPR_2BK_8K	MPTPR_PTP_DIV8		/* setting for 2 banks	*/
#define CFG_MPTPR_1BK_8K	MPTPR_PTP_DIV16		/* setting for 1 bank	*/

/*
 * MAMR settings for SDRAM
 */

/* 8 column SDRAM */
#define CFG_MAMR_8COL	((CFG_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
			 MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 |	\
			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
/* 9 column SDRAM */
#define CFG_MAMR_9COL	((CFG_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
			 MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 |	\
			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)


/*
 * Internal Definitions
 *
 * Boot Flags
 */
#define	BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
#define BOOTFLAG_WARM	0x02		/* Software reboot			*/

#endif	/* __CONFIG_H */