board/freescale/mpc8540ads/mpc8540ads.c

/*
 * Copyright 2004 Freescale Semiconductor.
 * (C) Copyright 2002,2003, Motorola Inc.
 * Xianghua Xiao, (X.Xiao@motorola.com)
 *
 * (C) Copyright 2002 Scott McNutt <smcnutt@artesyncp.com>
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */


#include <common.h>
#include <pci.h>
#include <asm/processor.h>
#include <asm/mmu.h>
#include <asm/immap_85xx.h>
#include <fsl_ddr_sdram.h>
#include <libfdt.h>
#include <fdt_support.h>

#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
extern void ddr_enable_ecc(unsigned int dram_size);
#endif

void local_bus_init(void);

int checkboard (void)
{
	puts("Board: ADS\n");

#ifdef CONFIG_PCI
	printf("PCI1: 32 bit, %d MHz (compiled)\n",
	       CONFIG_SYS_CLK_FREQ / 1000000);
#else
	printf("PCI1: disabled\n");
#endif

	/*
	 * Initialize local bus.
	 */
	local_bus_init();

	return 0;
}

/*
 * Initialize Local Bus
 */

void
local_bus_init(void)
{
	volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
	volatile fsl_lbc_t *lbc = LBC_BASE_ADDR;

	uint clkdiv;
	uint lbc_hz;
	sys_info_t sysinfo;

	/*
	 * Errata LBC11.
	 * Fix Local Bus clock glitch when DLL is enabled.
	 *
	 * If localbus freq is < 66MHz, DLL bypass mode must be used.
	 * If localbus freq is > 133MHz, DLL can be safely enabled.
	 * Between 66 and 133, the DLL is enabled with an override workaround.
	 */

	get_sys_info(&sysinfo);
	clkdiv = lbc->lcrr & LCRR_CLKDIV;
	lbc_hz = sysinfo.freq_systembus / 1000000 / clkdiv;

	if (lbc_hz < 66) {
		lbc->lcrr = CONFIG_SYS_LBC_LCRR | LCRR_DBYP;	/* DLL Bypass */

	} else if (lbc_hz >= 133) {
		lbc->lcrr = CONFIG_SYS_LBC_LCRR & (~LCRR_DBYP); /* DLL Enabled */

	} else {
		/*
		 * On REV1 boards, need to change CLKDIV before enable DLL.
		 * Default CLKDIV is 8, change it to 4 temporarily.
		 */
		uint pvr = get_pvr();
		uint temp_lbcdll = 0;

		if (pvr == PVR_85xx_REV1) {
			/* FIXME: Justify the high bit here. */
			lbc->lcrr = 0x10000004;
		}

		lbc->lcrr = CONFIG_SYS_LBC_LCRR & (~LCRR_DBYP); /* DLL Enabled */
		udelay(200);

		/*
		 * Sample LBC DLL ctrl reg, upshift it to set the
		 * override bits.
		 */
		temp_lbcdll = gur->lbcdllcr;
		gur->lbcdllcr = (((temp_lbcdll & 0xff) << 16) | 0x80000000);
		asm("sync;isync;msync");
	}
}


/*
 * Initialize SDRAM memory on the Local Bus.
 */
void lbc_sdram_init(void)
{
	volatile fsl_lbc_t *lbc = LBC_BASE_ADDR;
	uint *sdram_addr = (uint *)CONFIG_SYS_LBC_SDRAM_BASE;

	puts("LBC SDRAM: ");
	print_size(CONFIG_SYS_LBC_SDRAM_SIZE * 1024 * 1024,
		   "\n       ");

	/*
	 * Setup SDRAM Base and Option Registers
	 */
	set_lbc_or(2, CONFIG_SYS_OR2_PRELIM);
	set_lbc_br(2, CONFIG_SYS_BR2_PRELIM);
	lbc->lbcr = CONFIG_SYS_LBC_LBCR;
	asm("msync");

	lbc->lsrt = CONFIG_SYS_LBC_LSRT;
	lbc->mrtpr = CONFIG_SYS_LBC_MRTPR;
	asm("sync");

	/*
	 * Configure the SDRAM controller.
	 */
	lbc->lsdmr = CONFIG_SYS_LBC_LSDMR_1;
	asm("sync");
	*sdram_addr = 0xff;
	ppcDcbf((unsigned long) sdram_addr);
	udelay(100);

	lbc->lsdmr = CONFIG_SYS_LBC_LSDMR_2;
	asm("sync");
	*sdram_addr = 0xff;
	ppcDcbf((unsigned long) sdram_addr);
	udelay(100);

	lbc->lsdmr = CONFIG_SYS_LBC_LSDMR_3;
	asm("sync");
	*sdram_addr = 0xff;
	ppcDcbf((unsigned long) sdram_addr);
	udelay(100);

	lbc->lsdmr = CONFIG_SYS_LBC_LSDMR_4;
	asm("sync");
	*sdram_addr = 0xff;
	ppcDcbf((unsigned long) sdram_addr);
	udelay(100);

	lbc->lsdmr = CONFIG_SYS_LBC_LSDMR_5;
	asm("sync");
	*sdram_addr = 0xff;
	ppcDcbf((unsigned long) sdram_addr);
	udelay(100);
}

#if !defined(CONFIG_SPD_EEPROM)
/*************************************************************************
 *  fixed sdram init -- doesn't use serial presence detect.
 ************************************************************************/
phys_size_t fixed_sdram(void)
{
  #ifndef CONFIG_SYS_RAMBOOT
	struct ccsr_ddr __iomem *ddr =
		(struct ccsr_ddr __iomem *)(CONFIG_SYS_FSL_DDR_ADDR);

	ddr->cs0_bnds = CONFIG_SYS_DDR_CS0_BNDS;
	ddr->cs0_config = CONFIG_SYS_DDR_CS0_CONFIG;
	ddr->timing_cfg_1 = CONFIG_SYS_DDR_TIMING_1;
	ddr->timing_cfg_2 = CONFIG_SYS_DDR_TIMING_2;
	ddr->sdram_mode = CONFIG_SYS_DDR_MODE;
	ddr->sdram_interval = CONFIG_SYS_DDR_INTERVAL;
    #if defined (CONFIG_DDR_ECC)
	ddr->err_disable = 0x0000000D;
	ddr->err_sbe = 0x00ff0000;
    #endif
	asm("sync;isync;msync");
	udelay(500);
    #if defined (CONFIG_DDR_ECC)
	/* Enable ECC checking */
	ddr->sdram_cfg = (CONFIG_SYS_DDR_CONTROL | 0x20000000);
    #else
	ddr->sdram_cfg = CONFIG_SYS_DDR_CONTROL;
    #endif
	asm("sync; isync; msync");
	udelay(500);
  #endif
	return CONFIG_SYS_SDRAM_SIZE * 1024 * 1024;
}
#endif	/* !defined(CONFIG_SPD_EEPROM) */


#if defined(CONFIG_PCI)
/*
 * Initialize PCI Devices, report devices found.
 */


static struct pci_controller hose;

#endif	/* CONFIG_PCI */


void
pci_init_board(void)
{
#ifdef CONFIG_PCI
	pci_mpc85xx_init(&hose);
#endif /* CONFIG_PCI */
}


#if defined(CONFIG_OF_BOARD_SETUP)
void
ft_board_setup(void *blob, bd_t *bd)
{
	int node, tmp[2];
	const char *path;

	ft_cpu_setup(blob, bd);

	node = fdt_path_offset(blob, "/aliases");
	tmp[0] = 0;
	if (node >= 0) {
#ifdef CONFIG_PCI
		path = fdt_getprop(blob, node, "pci0", NULL);
		if (path) {
			tmp[1] = hose.last_busno - hose.first_busno;
			do_fixup_by_path(blob, path, "bus-range", &tmp, 8, 1);
		}
#endif
	}
}
#endif