blob: a04a49d0339c510502dab9c00034f7b98bc0c75a [file] [log] [blame]
Tom Rini83d290c2018-05-06 17:58:06 -04001/* SPDX-License-Identifier: GPL-2.0+ */
Shengzhou Liu8d67c362014-03-05 15:04:48 +08002/*
3 * Copyright 2014 Freescale Semiconductor, Inc.
Yangbo Lu34f39ce2021-06-03 10:51:19 +08004 * Copyright 2020-2021 NXP
Shengzhou Liu8d67c362014-03-05 15:04:48 +08005 */
6
7/*
8 * T2080 RDB/PCIe board configuration file
9 */
10
11#ifndef __T2080RDB_H
12#define __T2080RDB_H
13
Simon Glass1af3c7f2020-05-10 11:40:09 -060014#include <linux/stringify.h>
15
Shengzhou Liu8d67c362014-03-05 15:04:48 +080016#define CONFIG_ICS307_REFCLK_HZ 25000000 /* ICS307 ref clk freq */
Shengzhou Liu8d67c362014-03-05 15:04:48 +080017#define CONFIG_FSL_SATA_V2
18
19/* High Level Configuration Options */
Shengzhou Liu8d67c362014-03-05 15:04:48 +080020#define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */
Shengzhou Liu8d67c362014-03-05 15:04:48 +080021#define CONFIG_ENABLE_36BIT_PHYS
22
Shengzhou Liu8d67c362014-03-05 15:04:48 +080023#define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */
York Sun51370d52016-12-28 08:43:45 -080024#define CONFIG_SYS_NUM_CPC CONFIG_SYS_NUM_DDR_CTLRS
Shengzhou Liu8d67c362014-03-05 15:04:48 +080025
26#ifdef CONFIG_RAMBOOT_PBL
Masahiro Yamadae4536f82014-03-11 11:05:16 +090027#define CONFIG_SYS_FSL_PBL_PBI board/freescale/t208xrdb/t2080_pbi.cfg
Shengzhou Liu4d666682014-04-18 16:43:40 +080028
Shengzhou Liu4d666682014-04-18 16:43:40 +080029#define CONFIG_SPL_FLUSH_IMAGE
Shengzhou Liu4d666682014-04-18 16:43:40 +080030#define CONFIG_SPL_PAD_TO 0x40000
31#define CONFIG_SPL_MAX_SIZE 0x28000
32#define RESET_VECTOR_OFFSET 0x27FFC
33#define BOOT_PAGE_OFFSET 0x27000
34#ifdef CONFIG_SPL_BUILD
35#define CONFIG_SPL_SKIP_RELOCATE
36#define CONFIG_SPL_COMMON_INIT_DDR
37#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
Shengzhou Liu8d67c362014-03-05 15:04:48 +080038#endif
39
Miquel Raynal88718be2019-10-03 19:50:03 +020040#ifdef CONFIG_MTD_RAW_NAND
Shengzhou Liu4d666682014-04-18 16:43:40 +080041#define CONFIG_SYS_NAND_U_BOOT_SIZE (768 << 10)
42#define CONFIG_SYS_NAND_U_BOOT_DST 0x00200000
43#define CONFIG_SYS_NAND_U_BOOT_START 0x00200000
44#define CONFIG_SYS_NAND_U_BOOT_OFFS (256 << 10)
Zhao Qiangec90ac72016-09-08 12:55:32 +080045#define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xrdb/t2080_nand_rcw.cfg
Shengzhou Liu4d666682014-04-18 16:43:40 +080046#endif
47
48#ifdef CONFIG_SPIFLASH
49#define CONFIG_RESET_VECTOR_ADDRESS 0x200FFC
Shengzhou Liu4d666682014-04-18 16:43:40 +080050#define CONFIG_SPL_SPI_FLASH_MINIMAL
51#define CONFIG_SYS_SPI_FLASH_U_BOOT_SIZE (768 << 10)
52#define CONFIG_SYS_SPI_FLASH_U_BOOT_DST (0x00200000)
53#define CONFIG_SYS_SPI_FLASH_U_BOOT_START (0x00200000)
54#define CONFIG_SYS_SPI_FLASH_U_BOOT_OFFS (256 << 10)
Shengzhou Liu4d666682014-04-18 16:43:40 +080055#ifndef CONFIG_SPL_BUILD
56#define CONFIG_SYS_MPC85XX_NO_RESETVEC
57#endif
Zhao Qiangec90ac72016-09-08 12:55:32 +080058#define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xrdb/t2080_spi_rcw.cfg
Shengzhou Liu4d666682014-04-18 16:43:40 +080059#endif
60
61#ifdef CONFIG_SDCARD
62#define CONFIG_RESET_VECTOR_ADDRESS 0x200FFC
Shengzhou Liu4d666682014-04-18 16:43:40 +080063#define CONFIG_SYS_MMC_U_BOOT_SIZE (768 << 10)
64#define CONFIG_SYS_MMC_U_BOOT_DST (0x00200000)
65#define CONFIG_SYS_MMC_U_BOOT_START (0x00200000)
66#define CONFIG_SYS_MMC_U_BOOT_OFFS (260 << 10)
Shengzhou Liu4d666682014-04-18 16:43:40 +080067#ifndef CONFIG_SPL_BUILD
68#define CONFIG_SYS_MPC85XX_NO_RESETVEC
69#endif
Zhao Qiangec90ac72016-09-08 12:55:32 +080070#define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xrdb/t2080_sd_rcw.cfg
Shengzhou Liu4d666682014-04-18 16:43:40 +080071#endif
72
73#endif /* CONFIG_RAMBOOT_PBL */
74
Shengzhou Liu8d67c362014-03-05 15:04:48 +080075#define CONFIG_SRIO_PCIE_BOOT_MASTER
76#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
77/* Set 1M boot space */
78#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000)
79#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \
80 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR)
81#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
Shengzhou Liu8d67c362014-03-05 15:04:48 +080082#endif
83
Shengzhou Liu8d67c362014-03-05 15:04:48 +080084#ifndef CONFIG_RESET_VECTOR_ADDRESS
85#define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc
86#endif
87
88/*
89 * These can be toggled for performance analysis, otherwise use default.
90 */
91#define CONFIG_SYS_CACHE_STASHING
92#define CONFIG_BTB /* toggle branch predition */
93#define CONFIG_DDR_ECC
94#ifdef CONFIG_DDR_ECC
95#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
96#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
97#endif
98
Shengzhou Liu8d67c362014-03-05 15:04:48 +080099#ifndef __ASSEMBLY__
100unsigned long get_board_sys_clk(void);
101unsigned long get_board_ddr_clk(void);
102#endif
103
104#define CONFIG_SYS_CLK_FREQ 66660000
105#define CONFIG_DDR_CLK_FREQ 133330000
106
107/*
108 * Config the L3 Cache as L3 SRAM
109 */
Shengzhou Liu4d666682014-04-18 16:43:40 +0800110#define CONFIG_SYS_INIT_L3_ADDR 0xFFFC0000
111#define CONFIG_SYS_L3_SIZE (512 << 10)
112#define CONFIG_SPL_GD_ADDR (CONFIG_SYS_INIT_L3_ADDR + 32 * 1024)
Tom Rinia09fea12019-11-18 20:02:10 -0500113#define SPL_ENV_ADDR (CONFIG_SPL_GD_ADDR + 4 * 1024)
Shengzhou Liu4d666682014-04-18 16:43:40 +0800114#define CONFIG_SPL_RELOC_MALLOC_ADDR (CONFIG_SPL_GD_ADDR + 12 * 1024)
115#define CONFIG_SPL_RELOC_MALLOC_SIZE (50 << 10)
116#define CONFIG_SPL_RELOC_STACK (CONFIG_SPL_GD_ADDR + 64 * 1024)
Shengzhou Liu8d67c362014-03-05 15:04:48 +0800117
118#define CONFIG_SYS_DCSRBAR 0xf0000000
119#define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull
120
121/* EEPROM */
122#define CONFIG_ID_EEPROM
123#define CONFIG_SYS_I2C_EEPROM_NXID
124#define CONFIG_SYS_EEPROM_BUS_NUM 0
125#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
Shengzhou Liuef531c72014-04-18 16:43:41 +0800126#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
Shengzhou Liu8d67c362014-03-05 15:04:48 +0800127
128/*
129 * DDR Setup
130 */
131#define CONFIG_VERY_BIG_RAM
132#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
133#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
134#define CONFIG_DIMM_SLOTS_PER_CTLR 1
135#define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR)
136#define CONFIG_DDR_SPD
Shengzhou Liu8d67c362014-03-05 15:04:48 +0800137#define CONFIG_SYS_SPD_BUS_NUM 0
138#define CONFIG_SYS_SDRAM_SIZE 2048 /* for fixed parameter use */
139#define SPD_EEPROM_ADDRESS1 0x51
140#define SPD_EEPROM_ADDRESS2 0x52
141#define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1
142#define CTRL_INTLV_PREFERED cacheline
143
144/*
145 * IFC Definitions
146 */
147#define CONFIG_SYS_FLASH_BASE 0xe8000000
148#define CONFIG_SYS_FLASH_BASE_PHYS (0xf00000000ull | CONFIG_SYS_FLASH_BASE)
149#define CONFIG_SYS_NOR0_CSPR_EXT (0xf)
150#define CONFIG_SYS_NOR0_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
151 CSPR_PORT_SIZE_16 | \
152 CSPR_MSEL_NOR | \
153 CSPR_V)
154#define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024)
155
156/* NOR Flash Timing Params */
157#define CONFIG_SYS_NOR_CSOR CSOR_NAND_TRHZ_80
158
159#define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \
160 FTIM0_NOR_TEADC(0x5) | \
161 FTIM0_NOR_TEAHC(0x5))
162#define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \
163 FTIM1_NOR_TRAD_NOR(0x1A) |\
164 FTIM1_NOR_TSEQRAD_NOR(0x13))
165#define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \
166 FTIM2_NOR_TCH(0x4) | \
167 FTIM2_NOR_TWPH(0x0E) | \
168 FTIM2_NOR_TWP(0x1c))
169#define CONFIG_SYS_NOR_FTIM3 0x0
170
171#define CONFIG_SYS_FLASH_QUIET_TEST
172#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
173
174#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
175#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
176#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
177#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
178#define CONFIG_SYS_FLASH_EMPTY_INFO
179#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS }
180
181/* CPLD on IFC */
182#define CONFIG_SYS_CPLD_BASE 0xffdf0000
183#define CONFIG_SYS_CPLD_BASE_PHYS (0xf00000000ull | CONFIG_SYS_CPLD_BASE)
184#define CONFIG_SYS_CSPR2_EXT (0xf)
185#define CONFIG_SYS_CSPR2 (CSPR_PHYS_ADDR(CONFIG_SYS_CPLD_BASE) \
186 | CSPR_PORT_SIZE_8 \
187 | CSPR_MSEL_GPCM \
188 | CSPR_V)
189#define CONFIG_SYS_AMASK2 IFC_AMASK(64*1024)
190#define CONFIG_SYS_CSOR2 0x0
191
192/* CPLD Timing parameters for IFC CS2 */
193#define CONFIG_SYS_CS2_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \
194 FTIM0_GPCM_TEADC(0x0e) | \
195 FTIM0_GPCM_TEAHC(0x0e))
196#define CONFIG_SYS_CS2_FTIM1 (FTIM1_GPCM_TACO(0x0e) | \
197 FTIM1_GPCM_TRAD(0x1f))
198#define CONFIG_SYS_CS2_FTIM2 (FTIM2_GPCM_TCS(0x0e) | \
Shaohui Xiede519162014-06-26 14:41:33 +0800199 FTIM2_GPCM_TCH(0x8) | \
Shengzhou Liu8d67c362014-03-05 15:04:48 +0800200 FTIM2_GPCM_TWP(0x1f))
201#define CONFIG_SYS_CS2_FTIM3 0x0
202
203/* NAND Flash on IFC */
204#define CONFIG_NAND_FSL_IFC
205#define CONFIG_SYS_NAND_BASE 0xff800000
206#define CONFIG_SYS_NAND_BASE_PHYS (0xf00000000ull | CONFIG_SYS_NAND_BASE)
207
208#define CONFIG_SYS_NAND_CSPR_EXT (0xf)
209#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
210 | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
211 | CSPR_MSEL_NAND /* MSEL = NAND */ \
212 | CSPR_V)
213#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024)
214
215#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \
216 | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \
217 | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \
218 | CSOR_NAND_RAL_3 /* RAL = 2Byes */ \
219 | CSOR_NAND_PGS_2K /* Page Size = 2K */\
220 | CSOR_NAND_SPRZ_64 /* Spare size = 64 */\
221 | CSOR_NAND_PB(64)) /*Pages Per Block = 64*/
222
223#define CONFIG_SYS_NAND_ONFI_DETECTION
224
225/* ONFI NAND Flash mode0 Timing Params */
226#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \
227 FTIM0_NAND_TWP(0x18) | \
228 FTIM0_NAND_TWCHT(0x07) | \
229 FTIM0_NAND_TWH(0x0a))
230#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \
231 FTIM1_NAND_TWBE(0x39) | \
232 FTIM1_NAND_TRR(0x0e) | \
233 FTIM1_NAND_TRP(0x18))
234#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \
235 FTIM2_NAND_TREH(0x0a) | \
236 FTIM2_NAND_TWHRE(0x1e))
237#define CONFIG_SYS_NAND_FTIM3 0x0
238
239#define CONFIG_SYS_NAND_DDR_LAW 11
240#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
241#define CONFIG_SYS_MAX_NAND_DEVICE 1
Shengzhou Liu8d67c362014-03-05 15:04:48 +0800242#define CONFIG_SYS_NAND_BLOCK_SIZE (512 * 1024)
243
Miquel Raynal88718be2019-10-03 19:50:03 +0200244#if defined(CONFIG_MTD_RAW_NAND)
Shengzhou Liu8d67c362014-03-05 15:04:48 +0800245#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT
246#define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR
247#define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK
248#define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR
249#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0
250#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1
251#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2
252#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3
253#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR0_CSPR_EXT
254#define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR0_CSPR
255#define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK
256#define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR
257#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0
258#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1
259#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2
260#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3
261#else
262#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT
263#define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR
264#define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK
265#define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR
266#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0
267#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1
268#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2
269#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3
270#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NAND_CSPR_EXT
271#define CONFIG_SYS_CSPR1 CONFIG_SYS_NAND_CSPR
272#define CONFIG_SYS_AMASK1 CONFIG_SYS_NAND_AMASK
273#define CONFIG_SYS_CSOR1 CONFIG_SYS_NAND_CSOR
274#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NAND_FTIM0
275#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NAND_FTIM1
276#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NAND_FTIM2
277#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NAND_FTIM3
278#endif
279
280#if defined(CONFIG_RAMBOOT_PBL)
281#define CONFIG_SYS_RAMBOOT
282#endif
283
Shengzhou Liu4d666682014-04-18 16:43:40 +0800284#ifdef CONFIG_SPL_BUILD
285#define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE
286#else
287#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
288#endif
289
Shengzhou Liu8d67c362014-03-05 15:04:48 +0800290#define CONFIG_HWCONFIG
291
292/* define to use L1 as initial stack */
293#define CONFIG_L1_INIT_RAM
294#define CONFIG_SYS_INIT_RAM_LOCK
295#define CONFIG_SYS_INIT_RAM_ADDR 0xfdd00000 /* Initial L1 address */
296#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf
York Sunb3142e22015-08-17 13:31:51 -0700297#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW 0xfe03c000
Shengzhou Liu8d67c362014-03-05 15:04:48 +0800298/* The assembler doesn't like typecast */
299#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
300 ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
301 CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
302#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000
303#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
304 GENERATED_GBL_DATA_SIZE)
305#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
Prabhakar Kushwaha9307cba2014-03-31 15:31:48 +0530306#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
Shengzhou Liu8d67c362014-03-05 15:04:48 +0800307#define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024)
308
309/*
310 * Serial Port
311 */
Shengzhou Liu8d67c362014-03-05 15:04:48 +0800312#define CONFIG_SYS_NS16550_SERIAL
313#define CONFIG_SYS_NS16550_REG_SIZE 1
314#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2)
315#define CONFIG_SYS_BAUDRATE_TABLE \
316 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
317#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500)
318#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600)
319#define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500)
320#define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600)
321
Shengzhou Liu8d67c362014-03-05 15:04:48 +0800322/*
323 * I2C
324 */
Igor Opaniuk2147a162021-02-09 13:52:45 +0200325#if !CONFIG_IS_ENABLED(DM_I2C)
Simon Glass69d9eda2021-07-10 21:14:32 -0600326#define CONFIG_SYS_I2C_LEGACY
Shengzhou Liu8d67c362014-03-05 15:04:48 +0800327#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
328#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
329#define CONFIG_SYS_FSL_I2C3_SLAVE 0x7F
330#define CONFIG_SYS_FSL_I2C4_SLAVE 0x7F
331#define CONFIG_SYS_FSL_I2C_OFFSET 0x118000
332#define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100
333#define CONFIG_SYS_FSL_I2C3_OFFSET 0x119000
334#define CONFIG_SYS_FSL_I2C4_OFFSET 0x119100
335#define CONFIG_SYS_FSL_I2C_SPEED 100000
336#define CONFIG_SYS_FSL_I2C2_SPEED 100000
337#define CONFIG_SYS_FSL_I2C3_SPEED 100000
338#define CONFIG_SYS_FSL_I2C4_SPEED 100000
Biwen Li8e4be6d2020-05-01 20:04:19 +0800339#else
340#define CONFIG_I2C_SET_DEFAULT_BUS_NUM
341#define CONFIG_I2C_DEFAULT_BUS_NUMBER 0
342#endif
343
344#define CONFIG_SYS_I2C_FSL
345
Shengzhou Liu8d67c362014-03-05 15:04:48 +0800346#define I2C_MUX_PCA_ADDR_PRI 0x77 /* I2C bus multiplexer,primary */
347#define I2C_MUX_PCA_ADDR_SEC1 0x75 /* I2C bus multiplexer,secondary 1 */
348#define I2C_MUX_PCA_ADDR_SEC2 0x76 /* I2C bus multiplexer,secondary 2 */
349#define I2C_MUX_CH_DEFAULT 0x8
350
Ying Zhange5abb922015-03-10 14:21:36 +0800351#define I2C_MUX_CH_VOL_MONITOR 0xa
352
353#define CONFIG_VID_FLS_ENV "t208xrdb_vdd_mv"
354#ifndef CONFIG_SPL_BUILD
355#define CONFIG_VID
356#endif
357#define CONFIG_VOL_MONITOR_IR36021_SET
358#define CONFIG_VOL_MONITOR_IR36021_READ
359/* The lowest and highest voltage allowed for T208xRDB */
360#define VDD_MV_MIN 819
361#define VDD_MV_MAX 1212
Shengzhou Liu8d67c362014-03-05 15:04:48 +0800362
363/*
364 * RapidIO
365 */
366#define CONFIG_SYS_SRIO1_MEM_VIRT 0xa0000000
367#define CONFIG_SYS_SRIO1_MEM_PHYS 0xc20000000ull
368#define CONFIG_SYS_SRIO1_MEM_SIZE 0x10000000 /* 256M */
369#define CONFIG_SYS_SRIO2_MEM_VIRT 0xb0000000
370#define CONFIG_SYS_SRIO2_MEM_PHYS 0xc30000000ull
371#define CONFIG_SYS_SRIO2_MEM_SIZE 0x10000000 /* 256M */
372/*
373 * for slave u-boot IMAGE instored in master memory space,
374 * PHYS must be aligned based on the SIZE
375 */
Liu Gange4911812014-05-15 14:30:34 +0800376#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull
377#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull
378#define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x100000 /* 1M */
379#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull
Shengzhou Liu8d67c362014-03-05 15:04:48 +0800380/*
381 * for slave UCODE and ENV instored in master memory space,
382 * PHYS must be aligned based on the SIZE
383 */
Liu Gange4911812014-05-15 14:30:34 +0800384#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull
Shengzhou Liu8d67c362014-03-05 15:04:48 +0800385#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull
386#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000 /* 256K */
387
388/* slave core release by master*/
389#define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4
390#define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */
391
392/*
393 * SRIO_PCIE_BOOT - SLAVE
394 */
395#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
396#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000
397#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \
398 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR)
399#endif
400
401/*
402 * eSPI - Enhanced SPI
403 */
Shengzhou Liu8d67c362014-03-05 15:04:48 +0800404
405/*
406 * General PCI
407 * Memory space is mapped 1-1, but I/O space must start from 0.
408 */
Robert P. J. Dayb38eaec2016-05-03 19:52:49 -0400409#define CONFIG_PCIE1 /* PCIE controller 1 */
410#define CONFIG_PCIE2 /* PCIE controller 2 */
411#define CONFIG_PCIE3 /* PCIE controller 3 */
412#define CONFIG_PCIE4 /* PCIE controller 4 */
Shengzhou Liu8d67c362014-03-05 15:04:48 +0800413#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */
414/* controller 1, direct to uli, tgtid 3, Base address 20000 */
415#define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000
Shengzhou Liu8d67c362014-03-05 15:04:48 +0800416#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull
Shengzhou Liu8d67c362014-03-05 15:04:48 +0800417#define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000
Shengzhou Liu8d67c362014-03-05 15:04:48 +0800418#define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull
Shengzhou Liu8d67c362014-03-05 15:04:48 +0800419
420/* controller 2, Slot 2, tgtid 2, Base address 201000 */
421#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000
Shengzhou Liu8d67c362014-03-05 15:04:48 +0800422#define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull
Shengzhou Liu8d67c362014-03-05 15:04:48 +0800423#define CONFIG_SYS_PCIE2_IO_VIRT 0xf8010000
Shengzhou Liu8d67c362014-03-05 15:04:48 +0800424#define CONFIG_SYS_PCIE2_IO_PHYS 0xff8010000ull
Shengzhou Liu8d67c362014-03-05 15:04:48 +0800425
426/* controller 3, Slot 1, tgtid 1, Base address 202000 */
427#define CONFIG_SYS_PCIE3_MEM_VIRT 0xb0000000
Shengzhou Liu8d67c362014-03-05 15:04:48 +0800428#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc30000000ull
Shengzhou Liu8d67c362014-03-05 15:04:48 +0800429#define CONFIG_SYS_PCIE3_IO_VIRT 0xf8020000
Shengzhou Liu8d67c362014-03-05 15:04:48 +0800430#define CONFIG_SYS_PCIE3_IO_PHYS 0xff8020000ull
Shengzhou Liu8d67c362014-03-05 15:04:48 +0800431
432/* controller 4, Base address 203000 */
433#define CONFIG_SYS_PCIE4_MEM_VIRT 0xc0000000
Shengzhou Liu8d67c362014-03-05 15:04:48 +0800434#define CONFIG_SYS_PCIE4_MEM_PHYS 0xc40000000ull
Shengzhou Liu8d67c362014-03-05 15:04:48 +0800435#define CONFIG_SYS_PCIE4_IO_PHYS 0xff8030000ull
Shengzhou Liu8d67c362014-03-05 15:04:48 +0800436
437#ifdef CONFIG_PCI
Hou Zhiqiangd85fa792019-08-27 11:02:56 +0000438#if !defined(CONFIG_DM_PCI)
439#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */
440#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000
441#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
442#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
443#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
444#define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000
445#define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */
446#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000
447#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */
448#define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000
449#define CONFIG_SYS_PCIE3_MEM_SIZE 0x10000000 /* 256M */
450#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000
451#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */
452#define CONFIG_SYS_PCIE4_MEM_BUS 0xe0000000
453#define CONFIG_SYS_PCIE4_MEM_SIZE 0x10000000 /* 256M */
454#define CONFIG_SYS_PCIE4_IO_BUS 0x00000000
455#define CONFIG_SYS_PCIE4_IO_SIZE 0x00010000 /* 64k */
Shengzhou Liu8d67c362014-03-05 15:04:48 +0800456#define CONFIG_PCI_INDIRECT_BRIDGE
Hou Zhiqiangd85fa792019-08-27 11:02:56 +0000457#endif
Shengzhou Liu8d67c362014-03-05 15:04:48 +0800458#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
Shengzhou Liu8d67c362014-03-05 15:04:48 +0800459#endif
460
461/* Qman/Bman */
462#ifndef CONFIG_NOBQFMAN
Shengzhou Liu8d67c362014-03-05 15:04:48 +0800463#define CONFIG_SYS_BMAN_NUM_PORTALS 18
464#define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000
465#define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull
466#define CONFIG_SYS_BMAN_MEM_SIZE 0x02000000
Jeffrey Ladouceur3fa66db2014-12-08 14:54:01 -0500467#define CONFIG_SYS_BMAN_SP_CENA_SIZE 0x4000
468#define CONFIG_SYS_BMAN_SP_CINH_SIZE 0x1000
469#define CONFIG_SYS_BMAN_CENA_BASE CONFIG_SYS_BMAN_MEM_BASE
470#define CONFIG_SYS_BMAN_CENA_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
471#define CONFIG_SYS_BMAN_CINH_BASE (CONFIG_SYS_BMAN_MEM_BASE + \
472 CONFIG_SYS_BMAN_CENA_SIZE)
473#define CONFIG_SYS_BMAN_CINH_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
474#define CONFIG_SYS_BMAN_SWP_ISDR_REG 0xE08
Shengzhou Liu8d67c362014-03-05 15:04:48 +0800475#define CONFIG_SYS_QMAN_NUM_PORTALS 18
476#define CONFIG_SYS_QMAN_MEM_BASE 0xf6000000
477#define CONFIG_SYS_QMAN_MEM_PHYS 0xff6000000ull
478#define CONFIG_SYS_QMAN_MEM_SIZE 0x02000000
Jeffrey Ladouceur3fa66db2014-12-08 14:54:01 -0500479#define CONFIG_SYS_QMAN_SP_CENA_SIZE 0x4000
480#define CONFIG_SYS_QMAN_SP_CINH_SIZE 0x1000
481#define CONFIG_SYS_QMAN_CENA_BASE CONFIG_SYS_QMAN_MEM_BASE
482#define CONFIG_SYS_QMAN_CENA_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
483#define CONFIG_SYS_QMAN_CINH_BASE (CONFIG_SYS_QMAN_MEM_BASE + \
484 CONFIG_SYS_QMAN_CENA_SIZE)
485#define CONFIG_SYS_QMAN_CINH_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
486#define CONFIG_SYS_QMAN_SWP_ISDR_REG 0xE08
Shengzhou Liu8d67c362014-03-05 15:04:48 +0800487
488#define CONFIG_SYS_DPAA_FMAN
489#define CONFIG_SYS_DPAA_PME
490#define CONFIG_SYS_PMAN
491#define CONFIG_SYS_DPAA_DCE
492#define CONFIG_SYS_DPAA_RMAN /* RMan */
493#define CONFIG_SYS_INTERLAKEN
494
495/* Default address of microcode for the Linux Fman driver */
496#if defined(CONFIG_SPIFLASH)
497/*
498 * env is stored at 0x100000, sector size is 0x10000, ucode is stored after
499 * env, so we got 0x110000.
500 */
Shengzhou Liuef531c72014-04-18 16:43:41 +0800501#define CONFIG_SYS_FMAN_FW_ADDR 0x110000
Shengzhou Liu8d67c362014-03-05 15:04:48 +0800502#define CONFIG_CORTINA_FW_ADDR 0x120000
503
504#elif defined(CONFIG_SDCARD)
505/*
506 * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
Shengzhou Liu4d666682014-04-18 16:43:40 +0800507 * about 1MB (2048 blocks), Env is stored after the image, and the env size is
508 * 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 2080.
Shengzhou Liu8d67c362014-03-05 15:04:48 +0800509 */
Shengzhou Liu4d666682014-04-18 16:43:40 +0800510#define CONFIG_SYS_FMAN_FW_ADDR (512 * 0x820)
511#define CONFIG_CORTINA_FW_ADDR (512 * 0x8a0)
Shengzhou Liu8d67c362014-03-05 15:04:48 +0800512
Miquel Raynal88718be2019-10-03 19:50:03 +0200513#elif defined(CONFIG_MTD_RAW_NAND)
Shengzhou Liu4d666682014-04-18 16:43:40 +0800514#define CONFIG_SYS_FMAN_FW_ADDR (3 * CONFIG_SYS_NAND_BLOCK_SIZE)
515#define CONFIG_CORTINA_FW_ADDR (4 * CONFIG_SYS_NAND_BLOCK_SIZE)
Shengzhou Liu8d67c362014-03-05 15:04:48 +0800516#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
517/*
518 * Slave has no ucode locally, it can fetch this from remote. When implementing
519 * in two corenet boards, slave's ucode could be stored in master's memory
520 * space, the address can be mapped from slave TLB->slave LAW->
521 * slave SRIO or PCIE outbound window->master inbound window->
522 * master LAW->the ucode address in master's memory space.
523 */
Shengzhou Liuef531c72014-04-18 16:43:41 +0800524#define CONFIG_SYS_FMAN_FW_ADDR 0xFFE00000
Shengzhou Liu8d67c362014-03-05 15:04:48 +0800525#define CONFIG_CORTINA_FW_ADDR 0xFFE10000
526#else
Shengzhou Liuef531c72014-04-18 16:43:41 +0800527#define CONFIG_SYS_FMAN_FW_ADDR 0xEFF00000
Shengzhou Liu8d67c362014-03-05 15:04:48 +0800528#define CONFIG_CORTINA_FW_ADDR 0xEFE00000
529#endif
530#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000
531#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
532#endif /* CONFIG_NOBQFMAN */
533
534#ifdef CONFIG_SYS_DPAA_FMAN
Shengzhou Liu8d67c362014-03-05 15:04:48 +0800535#define CONFIG_CORTINA_FW_LENGTH 0x40000
536#define RGMII_PHY1_ADDR 0x01 /* RealTek RTL8211E */
537#define RGMII_PHY2_ADDR 0x02
538#define CORTINA_PHY_ADDR1 0x0c /* Cortina CS4315 */
539#define CORTINA_PHY_ADDR2 0x0d
Camelia Groza4e21a552021-06-16 17:47:31 +0530540/* Aquantia AQ1202 10G Base-T used by board revisions up to C */
541#define FM1_10GEC3_PHY_ADDR 0x00
Shengzhou Liu8d67c362014-03-05 15:04:48 +0800542#define FM1_10GEC4_PHY_ADDR 0x01
Camelia Groza4e21a552021-06-16 17:47:31 +0530543/* Aquantia AQR113C 10G Base-T used by board revisions D and up */
544#define AQR113C_PHY_ADDR1 0x00
545#define AQR113C_PHY_ADDR2 0x08
Shengzhou Liu8d67c362014-03-05 15:04:48 +0800546#endif
547
Shengzhou Liu8d67c362014-03-05 15:04:48 +0800548#ifdef CONFIG_FMAN_ENET
Shengzhou Liu8d67c362014-03-05 15:04:48 +0800549#define CONFIG_ETHPRIME "FM1@DTSEC3"
Shengzhou Liu8d67c362014-03-05 15:04:48 +0800550#endif
551
552/*
553 * SATA
554 */
555#ifdef CONFIG_FSL_SATA_V2
Shengzhou Liu8d67c362014-03-05 15:04:48 +0800556#define CONFIG_SYS_SATA_MAX_DEVICE 2
557#define CONFIG_SATA1
558#define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR
559#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA
560#define CONFIG_SATA2
561#define CONFIG_SYS_SATA2 CONFIG_SYS_MPC85xx_SATA2_ADDR
562#define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA
563#define CONFIG_LBA48
Shengzhou Liu8d67c362014-03-05 15:04:48 +0800564#endif
565
566/*
567 * USB
568 */
Tom Rini8850c5d2017-05-12 22:33:27 -0400569#ifdef CONFIG_USB_EHCI_HCD
Shengzhou Liu8d67c362014-03-05 15:04:48 +0800570#define CONFIG_USB_EHCI_FSL
571#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
Shengzhou Liu8d67c362014-03-05 15:04:48 +0800572#define CONFIG_HAS_FSL_DR_USB
573#endif
574
575/*
576 * SDHC
577 */
578#ifdef CONFIG_MMC
Shengzhou Liu8d67c362014-03-05 15:04:48 +0800579#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR
580#define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT
Shengzhou Liu8d67c362014-03-05 15:04:48 +0800581#endif
582
583/*
Shengzhou Liu4feac1c2014-04-02 14:28:35 +0800584 * Dynamic MTD Partition support with mtdparts
585 */
Shengzhou Liu4feac1c2014-04-02 14:28:35 +0800586
587/*
Shengzhou Liu8d67c362014-03-05 15:04:48 +0800588 * Environment
589 */
590
591/*
Shengzhou Liu8d67c362014-03-05 15:04:48 +0800592 * Miscellaneous configurable options
593 */
Shengzhou Liu8d67c362014-03-05 15:04:48 +0800594#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
Shengzhou Liu8d67c362014-03-05 15:04:48 +0800595
596/*
597 * For booting Linux, the board info and command line data
598 * have to be in the first 64 MB of memory, since this is
599 * the maximum mapped by the Linux kernel during initialization.
600 */
601#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial map for Linux*/
602#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
603
604#ifdef CONFIG_CMD_KGDB
605#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
606#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
607#endif
608
609/*
610 * Environment Configuration
611 */
612#define CONFIG_ROOTPATH "/opt/nfsroot"
613#define CONFIG_BOOTFILE "uImage"
614#define CONFIG_UBOOTPATH "u-boot.bin" /* U-Boot image on TFTP server */
615
616/* default location for tftp and bootm */
617#define CONFIG_LOADADDR 1000000
Shengzhou Liu8d67c362014-03-05 15:04:48 +0800618#define __USB_PHY_TYPE utmi
619
620#define CONFIG_EXTRA_ENV_SETTINGS \
621 "hwconfig=fsl_ddr:" \
622 "ctlr_intlv=" __stringify(CTRL_INTLV_PREFERED) "," \
623 "bank_intlv=auto;" \
624 "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
625 "netdev=eth0\0" \
626 "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \
627 "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \
628 "tftpflash=tftpboot $loadaddr $uboot && " \
629 "protect off $ubootaddr +$filesize && " \
630 "erase $ubootaddr +$filesize && " \
631 "cp.b $loadaddr $ubootaddr $filesize && " \
632 "protect on $ubootaddr +$filesize && " \
633 "cmp.b $loadaddr $ubootaddr $filesize\0" \
634 "consoledev=ttyS0\0" \
635 "ramdiskaddr=2000000\0" \
636 "ramdiskfile=t2080rdb/ramdisk.uboot\0" \
Scott Woodb24a4f62016-07-19 17:52:06 -0500637 "fdtaddr=1e00000\0" \
Shengzhou Liu8d67c362014-03-05 15:04:48 +0800638 "fdtfile=t2080rdb/t2080rdb.dtb\0" \
Kim Phillips32465842014-05-14 19:33:45 -0500639 "bdev=sda3\0"
Shengzhou Liu8d67c362014-03-05 15:04:48 +0800640
641/*
642 * For emulation this causes u-boot to jump to the start of the
643 * proof point app code automatically
644 */
645#define CONFIG_PROOF_POINTS \
646 "setenv bootargs root=/dev/$bdev rw " \
647 "console=$consoledev,$baudrate $othbootargs;" \
648 "cpu 1 release 0x29000000 - - -;" \
649 "cpu 2 release 0x29000000 - - -;" \
650 "cpu 3 release 0x29000000 - - -;" \
651 "cpu 4 release 0x29000000 - - -;" \
652 "cpu 5 release 0x29000000 - - -;" \
653 "cpu 6 release 0x29000000 - - -;" \
654 "cpu 7 release 0x29000000 - - -;" \
655 "go 0x29000000"
656
657#define CONFIG_HVBOOT \
658 "setenv bootargs config-addr=0x60000000; " \
659 "bootm 0x01000000 - 0x00f00000"
660
661#define CONFIG_ALU \
662 "setenv bootargs root=/dev/$bdev rw " \
663 "console=$consoledev,$baudrate $othbootargs;" \
664 "cpu 1 release 0x01000000 - - -;" \
665 "cpu 2 release 0x01000000 - - -;" \
666 "cpu 3 release 0x01000000 - - -;" \
667 "cpu 4 release 0x01000000 - - -;" \
668 "cpu 5 release 0x01000000 - - -;" \
669 "cpu 6 release 0x01000000 - - -;" \
670 "cpu 7 release 0x01000000 - - -;" \
671 "go 0x01000000"
672
673#define CONFIG_LINUX \
674 "setenv bootargs root=/dev/ram rw " \
675 "console=$consoledev,$baudrate $othbootargs;" \
676 "setenv ramdiskaddr 0x02000000;" \
677 "setenv fdtaddr 0x00c00000;" \
678 "setenv loadaddr 0x1000000;" \
679 "bootm $loadaddr $ramdiskaddr $fdtaddr"
680
681#define CONFIG_HDBOOT \
682 "setenv bootargs root=/dev/$bdev rw " \
683 "console=$consoledev,$baudrate $othbootargs;" \
684 "tftp $loadaddr $bootfile;" \
685 "tftp $fdtaddr $fdtfile;" \
686 "bootm $loadaddr - $fdtaddr"
687
688#define CONFIG_NFSBOOTCOMMAND \
689 "setenv bootargs root=/dev/nfs rw " \
690 "nfsroot=$serverip:$rootpath " \
691 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
692 "console=$consoledev,$baudrate $othbootargs;" \
693 "tftp $loadaddr $bootfile;" \
694 "tftp $fdtaddr $fdtfile;" \
695 "bootm $loadaddr - $fdtaddr"
696
697#define CONFIG_RAMBOOTCOMMAND \
698 "setenv bootargs root=/dev/ram rw " \
699 "console=$consoledev,$baudrate $othbootargs;" \
700 "tftp $ramdiskaddr $ramdiskfile;" \
701 "tftp $loadaddr $bootfile;" \
702 "tftp $fdtaddr $fdtfile;" \
703 "bootm $loadaddr $ramdiskaddr $fdtaddr"
704
705#define CONFIG_BOOTCOMMAND CONFIG_LINUX
706
Shengzhou Liu8d67c362014-03-05 15:04:48 +0800707#include <asm/fsl_secure_boot.h>
Aneesh Bansalef6c55a2016-01-22 16:37:22 +0530708
Shengzhou Liu8d67c362014-03-05 15:04:48 +0800709#endif /* __T2080RDB_H */