| Evgeni Dobrev | 9637c4b | 2014-12-08 17:49:42 +0100 | [diff] [blame] | 1 | /* |
| 2 | * Copyright (C) 2014 Evgeni Dobrev <evgeni@studio-punkt.com> |
| 3 | * |
| 4 | * Based on sheevaplug.c originally written by |
| 5 | * Prafulla Wadaskar <prafulla@marvell.com> |
| 6 | * (C) Copyright 2009 |
| 7 | * Marvell Semiconductor <www.marvell.com> |
| 8 | * |
| 9 | * SPDX-License-Identifier: GPL-2.0+ |
| 10 | */ |
| 11 | |
| 12 | #include <common.h> |
| 13 | #include <miiphy.h> |
| 14 | #include <asm/arch/soc.h> |
| 15 | #include <asm/arch/mpp.h> |
| 16 | #include <asm/arch/cpu.h> |
| 17 | #include <asm/io.h> |
| 18 | |
| 19 | DECLARE_GLOBAL_DATA_PTR; |
| 20 | |
| 21 | int board_early_init_f(void) |
| 22 | { |
| 23 | /* |
| 24 | * default gpio configuration |
| 25 | */ |
| 26 | mvebu_config_gpio(NAS220_GE_OE_VAL_LOW, NAS220_GE_OE_VAL_HIGH, |
| 27 | NAS220_GE_OE_LOW, NAS220_GE_OE_HIGH); |
| 28 | |
| 29 | /* Multi-Purpose Pins Functionality configuration */ |
| 30 | static const u32 kwmpp_config[] = { |
| 31 | MPP0_NF_IO2, |
| 32 | MPP1_NF_IO3, |
| 33 | MPP2_NF_IO4, |
| 34 | MPP3_NF_IO5, |
| 35 | MPP4_NF_IO6, |
| 36 | MPP5_NF_IO7, |
| 37 | MPP6_SYSRST_OUTn, |
| 38 | MPP7_SPI_SCn, |
| 39 | MPP8_TW_SDA, |
| 40 | MPP9_TW_SCK, |
| 41 | MPP10_UART0_TXD, |
| 42 | MPP11_UART0_RXD, |
| 43 | MPP12_GPO, |
| 44 | MPP13_GPIO, |
| 45 | MPP14_GPIO, |
| 46 | MPP15_SATA0_ACTn, |
| 47 | MPP16_SATA1_ACTn, |
| 48 | MPP17_SATA0_PRESENTn, |
| 49 | MPP18_NF_IO0, |
| 50 | MPP19_NF_IO1, |
| 51 | MPP20_GPIO, |
| 52 | MPP21_GPIO, |
| 53 | MPP22_GPIO, |
| 54 | MPP23_GPIO, |
| 55 | MPP24_GPIO, |
| 56 | MPP25_GPIO, |
| 57 | MPP26_GPIO, |
| 58 | MPP27_GPIO, |
| 59 | MPP28_GPIO, |
| 60 | MPP29_GPIO, |
| 61 | MPP30_GPIO, |
| 62 | MPP31_GPIO, |
| 63 | MPP32_GPIO, |
| 64 | MPP33_GPIO, |
| 65 | MPP34_GPIO, |
| 66 | MPP35_GPIO, |
| 67 | 0 |
| 68 | }; |
| 69 | kirkwood_mpp_conf(kwmpp_config, NULL); |
| 70 | return 0; |
| 71 | } |
| 72 | |
| 73 | int board_init(void) |
| 74 | { |
| 75 | /* |
| 76 | * arch number of board |
| 77 | */ |
| 78 | gd->bd->bi_arch_number = MACH_TYPE_NAS220; |
| 79 | |
| 80 | /* adress of boot parameters */ |
| 81 | gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100; |
| 82 | |
| 83 | return 0; |
| 84 | } |
| 85 | |
| 86 | #ifdef CONFIG_RESET_PHY_R |
| 87 | /* Configure and enable MV88E1116 PHY */ |
| 88 | void reset_phy(void) |
| 89 | { |
| 90 | u16 reg; |
| 91 | u16 devadr; |
| 92 | char *name = "egiga0"; |
| 93 | |
| 94 | if (miiphy_set_current_dev(name)) |
| 95 | return; |
| 96 | |
| 97 | /* command to read PHY dev address */ |
| 98 | if (miiphy_read(name, 0xEE, 0xEE, (u16 *)&devadr)) { |
| 99 | printf("Err..%s could not read PHY dev address\n", __func__); |
| 100 | return; |
| 101 | } |
| 102 | |
| 103 | /* |
| 104 | * Enable RGMII delay on Tx and Rx for CPU port |
| 105 | * Ref: sec 4.7.2 of chip datasheet |
| 106 | */ |
| 107 | miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2); |
| 108 | miiphy_read(name, devadr, MV88E1116_MAC_CTRL_REG, ®); |
| 109 | reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL); |
| 110 | miiphy_write(name, devadr, MV88E1116_MAC_CTRL_REG, reg); |
| 111 | miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0); |
| 112 | |
| 113 | /* reset the phy */ |
| 114 | miiphy_reset(name, devadr); |
| 115 | |
| 116 | printf("88E1116 Initialized on %s\n", name); |
| 117 | } |
| 118 | #endif /* CONFIG_RESET_PHY_R */ |