blob: a0d291eef481926931c4c1e8005cca834ee396e4 [file] [log] [blame]
Jon Loeligerd9b94f22005-07-25 14:05:07 -05001/*
2 * Copyright 2004 Freescale Semiconductor.
3 *
4 * See file CREDITS for list of people who contributed to this
5 * project.
6 *
7 * This program is free software; you can redistribute it and/or
8 * modify it under the terms of the GNU General Public License as
9 * published by the Free Software Foundation; either version 2 of
10 * the License, or (at your option) any later version.
11 *
12 * This program is distributed in the hope that it will be useful,
13 * but WITHOUT ANY WARRANTY; without even the implied warranty of
14 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
15 * GNU General Public License for more details.
16 *
17 * You should have received a copy of the GNU General Public License
18 * along with this program; if not, write to the Free Software
19 * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
20 * MA 02111-1307 USA
21 */
22
23/*
24 * mpc8548cds board configuration file
25 *
26 * Please refer to doc/README.mpc85xxcds for more info.
27 *
28 */
29#ifndef __CONFIG_H
30#define __CONFIG_H
31
32/* High Level Configuration Options */
33#define CONFIG_BOOKE 1 /* BOOKE */
34#define CONFIG_E500 1 /* BOOKE e500 family */
35#define CONFIG_MPC85xx 1 /* MPC8540/60/55/41/48 */
36#define CONFIG_MPC8548 1 /* MPC8548 specific */
37#define CONFIG_MPC8548CDS 1 /* MPC8548CDS board specific */
38
Zang Roy-r6191141fb7e02006-12-14 14:14:55 +080039#define CONFIG_PCI
Jon Loeligerd9b94f22005-07-25 14:05:07 -050040#define CONFIG_TSEC_ENET /* tsec ethernet support */
41#define CONFIG_ENV_OVERWRITE
42#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
43#define CONFIG_DDR_DLL /* possible DLL fix needed */
ebony.zhu@freescale.com39b18c42006-12-18 16:25:15 +080044#undef CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */
Jon Loeligerd9b94f22005-07-25 14:05:07 -050045
46#define CONFIG_DDR_ECC /* only for ECC DDR module */
47#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */
48#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
49
50
51/*
52 * When initializing flash, if we cannot find the manufacturer ID,
53 * assume this is the AMD flash associated with the CDS board.
54 * This allows booting from a promjet.
55 */
56#define CONFIG_ASSUME_AMD_FLASH
57
58#define MPC85xx_DDR_SDRAM_CLK_CNTL /* 85xx has clock control reg */
59
60#ifndef __ASSEMBLY__
61extern unsigned long get_clock_freq(void);
62#endif
63#define CONFIG_SYS_CLK_FREQ get_clock_freq() /* sysclk for MPC85xx */
64
65/*
66 * These can be toggled for performance analysis, otherwise use default.
67 */
68#define CONFIG_L2_CACHE /* toggle L2 cache */
69#define CONFIG_BTB /* toggle branch predition */
70#define CONFIG_ADDR_STREAMING /* toggle addr streaming */
71
72/*
73 * Only possible on E500 Version 2 or newer cores.
74 */
75#define CONFIG_ENABLE_36BIT_PHYS 1
76
77
78#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
79
80#undef CFG_DRAM_TEST /* memory test, takes time */
81#define CFG_MEMTEST_START 0x00200000 /* memtest works on */
82#define CFG_MEMTEST_END 0x00400000
83
84/*
85 * Base addresses -- Note these are effective addresses where the
86 * actual resources get mapped (not physical addresses)
87 */
88#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
89#define CFG_CCSRBAR 0xe0000000 /* relocated CCSRBAR */
90#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */
91
92/*
93 * DDR Setup
94 */
95#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/
96#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE
97
98#define SPD_EEPROM_ADDRESS 0x51 /* DDR DIMM */
99
100/*
101 * Make sure required options are set
102 */
103#ifndef CONFIG_SPD_EEPROM
104#error ("CONFIG_SPD_EEPROM is required")
105#endif
106
107#undef CONFIG_CLOCKS_IN_MHZ
108
109
110/*
111 * Local Bus Definitions
112 */
113
114/*
115 * FLASH on the Local Bus
116 * Two banks, 8M each, using the CFI driver.
117 * Boot from BR0/OR0 bank at 0xff00_0000
118 * Alternate BR1/OR1 bank at 0xff80_0000
119 *
120 * BR0, BR1:
121 * Base address 0 = 0xff00_0000 = BR0[0:16] = 1111 1111 0000 0000 0
122 * Base address 1 = 0xff80_0000 = BR1[0:16] = 1111 1111 1000 0000 0
123 * Port Size = 16 bits = BRx[19:20] = 10
124 * Use GPCM = BRx[24:26] = 000
125 * Valid = BRx[31] = 1
126 *
127 * 0 4 8 12 16 20 24 28
128 * 1111 1111 1000 0000 0001 0000 0000 0001 = ff801001 BR0
129 * 1111 1111 0000 0000 0001 0000 0000 0001 = ff001001 BR1
130 *
131 * OR0, OR1:
132 * Addr Mask = 8M = ORx[0:16] = 1111 1111 1000 0000 0
133 * Reserved ORx[17:18] = 11, confusion here?
134 * CSNT = ORx[20] = 1
135 * ACS = half cycle delay = ORx[21:22] = 11
136 * SCY = 6 = ORx[24:27] = 0110
137 * TRLX = use relaxed timing = ORx[29] = 1
138 * EAD = use external address latch delay = OR[31] = 1
139 *
140 * 0 4 8 12 16 20 24 28
141 * 1111 1111 1000 0000 0110 1110 0110 0101 = ff806e65 ORx
142 */
143
144#define CFG_FLASH_BASE 0xff000000 /* start of FLASH 8M */
145
146#define CFG_BR0_PRELIM 0xff801001
147#define CFG_BR1_PRELIM 0xff001001
148
149#define CFG_OR0_PRELIM 0xff806e65
150#define CFG_OR1_PRELIM 0xff806e65
151
152#define CFG_FLASH_BANKS_LIST {0xff800000, CFG_FLASH_BASE}
153#define CFG_MAX_FLASH_BANKS 2 /* number of banks */
154#define CFG_MAX_FLASH_SECT 128 /* sectors per device */
155#undef CFG_FLASH_CHECKSUM
156#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
157#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
158
159#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
160
161#define CFG_FLASH_CFI_DRIVER
162#define CFG_FLASH_CFI
163#define CFG_FLASH_EMPTY_INFO
164
165
166/*
167 * SDRAM on the Local Bus
168 */
169#define CFG_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */
170#define CFG_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */
171
172/*
173 * Base Register 2 and Option Register 2 configure SDRAM.
174 * The SDRAM base address, CFG_LBC_SDRAM_BASE, is 0xf0000000.
175 *
176 * For BR2, need:
177 * Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0
178 * port-size = 32-bits = BR2[19:20] = 11
179 * no parity checking = BR2[21:22] = 00
180 * SDRAM for MSEL = BR2[24:26] = 011
181 * Valid = BR[31] = 1
182 *
183 * 0 4 8 12 16 20 24 28
184 * 1111 0000 0000 0000 0001 1000 0110 0001 = f0001861
185 *
186 * FIXME: CFG_LBC_SDRAM_BASE should be masked and OR'ed into
187 * FIXME: the top 17 bits of BR2.
188 */
189
190#define CFG_BR2_PRELIM 0xf0001861
191
192/*
193 * The SDRAM size in MB, CFG_LBC_SDRAM_SIZE, is 64.
194 *
195 * For OR2, need:
196 * 64MB mask for AM, OR2[0:7] = 1111 1100
197 * XAM, OR2[17:18] = 11
198 * 9 columns OR2[19-21] = 010
199 * 13 rows OR2[23-25] = 100
200 * EAD set for extra time OR[31] = 1
201 *
202 * 0 4 8 12 16 20 24 28
203 * 1111 1100 0000 0000 0110 1001 0000 0001 = fc006901
204 */
205
206#define CFG_OR2_PRELIM 0xfc006901
207
208#define CFG_LBC_LCRR 0x00030004 /* LB clock ratio reg */
209#define CFG_LBC_LBCR 0x00000000 /* LB config reg */
210#define CFG_LBC_LSRT 0x20000000 /* LB sdram refresh timer */
211#define CFG_LBC_MRTPR 0x00000000 /* LB refresh timer prescal*/
212
213/*
214 * LSDMR masks
215 */
216#define CFG_LBC_LSDMR_RFEN (1 << (31 - 1))
217#define CFG_LBC_LSDMR_BSMA1516 (3 << (31 - 10))
218#define CFG_LBC_LSDMR_BSMA1617 (4 << (31 - 10))
219#define CFG_LBC_LSDMR_RFCR16 (7 << (31 - 16))
220#define CFG_LBC_LSDMR_PRETOACT7 (7 << (31 - 19))
221#define CFG_LBC_LSDMR_ACTTORW7 (7 << (31 - 22))
222#define CFG_LBC_LSDMR_ACTTORW6 (6 << (31 - 22))
223#define CFG_LBC_LSDMR_BL8 (1 << (31 - 23))
224#define CFG_LBC_LSDMR_WRC4 (0 << (31 - 27))
225#define CFG_LBC_LSDMR_CL3 (3 << (31 - 31))
226
227#define CFG_LBC_LSDMR_OP_NORMAL (0 << (31 - 4))
228#define CFG_LBC_LSDMR_OP_ARFRSH (1 << (31 - 4))
229#define CFG_LBC_LSDMR_OP_SRFRSH (2 << (31 - 4))
230#define CFG_LBC_LSDMR_OP_MRW (3 << (31 - 4))
231#define CFG_LBC_LSDMR_OP_PRECH (4 << (31 - 4))
232#define CFG_LBC_LSDMR_OP_PCHALL (5 << (31 - 4))
233#define CFG_LBC_LSDMR_OP_ACTBNK (6 << (31 - 4))
234#define CFG_LBC_LSDMR_OP_RWINV (7 << (31 - 4))
235
236/*
237 * Common settings for all Local Bus SDRAM commands.
238 * At run time, either BSMA1516 (for CPU 1.1)
239 * or BSMA1617 (for CPU 1.0) (old)
240 * is OR'ed in too.
241 */
242#define CFG_LBC_LSDMR_COMMON ( CFG_LBC_LSDMR_RFCR16 \
243 | CFG_LBC_LSDMR_PRETOACT7 \
244 | CFG_LBC_LSDMR_ACTTORW7 \
245 | CFG_LBC_LSDMR_BL8 \
246 | CFG_LBC_LSDMR_WRC4 \
247 | CFG_LBC_LSDMR_CL3 \
248 | CFG_LBC_LSDMR_RFEN \
249 )
250
251/*
252 * The CADMUS registers are connected to CS3 on CDS.
253 * The new memory map places CADMUS at 0xf8000000.
254 *
255 * For BR3, need:
256 * Base address of 0xf8000000 = BR[0:16] = 1111 1000 0000 0000 0
257 * port-size = 8-bits = BR[19:20] = 01
258 * no parity checking = BR[21:22] = 00
259 * GPMC for MSEL = BR[24:26] = 000
260 * Valid = BR[31] = 1
261 *
262 * 0 4 8 12 16 20 24 28
263 * 1111 1000 0000 0000 0000 1000 0000 0001 = f8000801
264 *
265 * For OR3, need:
266 * 1 MB mask for AM, OR[0:16] = 1111 1111 1111 0000 0
267 * disable buffer ctrl OR[19] = 0
268 * CSNT OR[20] = 1
269 * ACS OR[21:22] = 11
270 * XACS OR[23] = 1
271 * SCY 15 wait states OR[24:27] = 1111 max is suboptimal but safe
272 * SETA OR[28] = 0
273 * TRLX OR[29] = 1
274 * EHTR OR[30] = 1
275 * EAD extra time OR[31] = 1
276 *
277 * 0 4 8 12 16 20 24 28
278 * 1111 1111 1111 0000 0000 1111 1111 0111 = fff00ff7
279 */
280
281#define CADMUS_BASE_ADDR 0xf8000000
282#define CFG_BR3_PRELIM 0xf8000801
283#define CFG_OR3_PRELIM 0xfff00ff7
284
285#define CONFIG_L1_INIT_RAM
286#define CFG_INIT_RAM_LOCK 1
287#define CFG_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */
288#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */
289
290#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */
291#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
292#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
293
294#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
295#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
296
297/* Serial Port */
298#define CONFIG_CONS_INDEX 2
299#undef CONFIG_SERIAL_SOFTWARE_FIFO
300#define CFG_NS16550
301#define CFG_NS16550_SERIAL
302#define CFG_NS16550_REG_SIZE 1
303#define CFG_NS16550_CLK get_bus_freq(0)
304
305#define CFG_BAUDRATE_TABLE \
306 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
307
308#define CFG_NS16550_COM1 (CFG_CCSRBAR+0x4500)
309#define CFG_NS16550_COM2 (CFG_CCSRBAR+0x4600)
310
311/* Use the HUSH parser */
312#define CFG_HUSH_PARSER
313#ifdef CFG_HUSH_PARSER
314#define CFG_PROMPT_HUSH_PS2 "> "
315#endif
316
Matthew McClintock40d5fa32006-06-28 10:43:36 -0500317/* pass open firmware flat tree */
318#define CONFIG_OF_FLAT_TREE 1
319#define CONFIG_OF_BOARD_SETUP 1
320
321/* maximum size of the flat tree (8K) */
322#define OF_FLAT_TREE_MAX_SIZE 8192
323
324#define OF_CPU "PowerPC,8548@0"
325#define OF_SOC "soc8548@e0000000"
326#define OF_TBCLK (bd->bi_busfreq / 8)
Matthew McClintockcbfc7ce2006-06-28 10:46:13 -0500327#define OF_STDOUT_PATH "/soc8548@e0000000/serial@4600"
Matthew McClintock40d5fa32006-06-28 10:43:36 -0500328
Jon Loeliger20476722006-10-20 15:50:15 -0500329/*
330 * I2C
331 */
332#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
333#define CONFIG_HARD_I2C /* I2C with hardware support*/
Jon Loeligerd9b94f22005-07-25 14:05:07 -0500334#undef CONFIG_SOFT_I2C /* I2C bit-banged */
335#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
336#define CFG_I2C_EEPROM_ADDR 0x57
337#define CFG_I2C_SLAVE 0x7F
338#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
Jon Loeliger20476722006-10-20 15:50:15 -0500339#define CFG_I2C_OFFSET 0x3000
Jon Loeligerd9b94f22005-07-25 14:05:07 -0500340
341/*
342 * General PCI
Sergei Shtylyov362dd832006-12-27 22:07:15 +0300343 * Memory space is mapped 1-1, but I/O space must start from 0.
Jon Loeligerd9b94f22005-07-25 14:05:07 -0500344 */
345#define CFG_PCI1_MEM_BASE 0x80000000
346#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE
Zang Roy-r6191141fb7e02006-12-14 14:14:55 +0800347#define CFG_PCI1_MEM_SIZE 0x10000000 /* 256M */
Matthew McClintockcbfc7ce2006-06-28 10:46:13 -0500348#define CFG_PCI1_IO_BASE 0x00000000
349#define CFG_PCI1_IO_PHYS 0xe2000000
Zang Roy-r6191141fb7e02006-12-14 14:14:55 +0800350#define CFG_PCI1_IO_SIZE 0x00800000 /* 8M */
Jon Loeligerd9b94f22005-07-25 14:05:07 -0500351
Zang Roy-r6191141fb7e02006-12-14 14:14:55 +0800352#define CFG_PCI2_MEM_BASE 0x90000000
Jon Loeligerd9b94f22005-07-25 14:05:07 -0500353#define CFG_PCI2_MEM_PHYS CFG_PCI2_MEM_BASE
Zang Roy-r6191141fb7e02006-12-14 14:14:55 +0800354#define CFG_PCI2_MEM_SIZE 0x10000000 /* 256M */
Andy Flemingffa621a2007-02-24 01:08:13 -0600355#define CFG_PCI2_IO_BASE 0x00000000
Zang Roy-r6191141fb7e02006-12-14 14:14:55 +0800356#define CFG_PCI2_IO_PHYS 0xe2800000
357#define CFG_PCI2_IO_SIZE 0x00800000 /* 8M */
Jon Loeligerd9b94f22005-07-25 14:05:07 -0500358
Zang Roy-r6191141fb7e02006-12-14 14:14:55 +0800359#define CFG_PEX_MEM_BASE 0xa0000000
360#define CFG_PEX_MEM_PHYS CFG_PEX_MEM_BASE
361#define CFG_PEX_MEM_SIZE 0x20000000 /* 512M */
Andy Flemingffa621a2007-02-24 01:08:13 -0600362#define CFG_PEX_IO_BASE 0x00000000
363#define CFG_PEX_IO_PHYS 0xe3000000
364#define CFG_PEX_IO_SIZE 0x01000000 /* 16M */
Zang Roy-r6191141fb7e02006-12-14 14:14:55 +0800365
366/*
367 * RapidIO MMU
368 */
369#define CFG_RIO_MEM_BASE 0xC0000000
370#define CFG_RIO_MEM_SIZE 0x20000000 /* 512M */
Jon Loeligerd9b94f22005-07-25 14:05:07 -0500371
372#if defined(CONFIG_PCI)
373
374#define CONFIG_NET_MULTI
375#define CONFIG_PCI_PNP /* do pci plug-and-play */
Matthew McClintockcbfc7ce2006-06-28 10:46:13 -0500376#define CONFIG_85XX_PCI2
Jon Loeligerd9b94f22005-07-25 14:05:07 -0500377
378#undef CONFIG_EEPRO100
379#undef CONFIG_TULIP
380
Jon Loeligerd9b94f22005-07-25 14:05:07 -0500381#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
382#define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */
383
384#endif /* CONFIG_PCI */
385
386
387#if defined(CONFIG_TSEC_ENET)
388
389#ifndef CONFIG_NET_MULTI
390#define CONFIG_NET_MULTI 1
391#endif
392
393#define CONFIG_MII 1 /* MII PHY management */
Kim Phillips255a35772007-05-16 16:52:19 -0500394#define CONFIG_TSEC1 1
395#define CONFIG_TSEC1_NAME "eTSEC0"
396#define CONFIG_TSEC2 1
397#define CONFIG_TSEC2_NAME "eTSEC1"
398#define CONFIG_TSEC3 1
399#define CONFIG_TSEC3_NAME "eTSEC2"
400#undef CONFIG_TSEC4
401#define CONFIG_TSEC4_NAME "eTSEC3"
Jon Loeligerd9b94f22005-07-25 14:05:07 -0500402#undef CONFIG_MPC85XX_FEC
403
404#define TSEC1_PHY_ADDR 0
405#define TSEC2_PHY_ADDR 1
406#define TSEC3_PHY_ADDR 2
407#define TSEC4_PHY_ADDR 3
Jon Loeligerd9b94f22005-07-25 14:05:07 -0500408
409#define TSEC1_PHYIDX 0
410#define TSEC2_PHYIDX 0
411#define TSEC3_PHYIDX 0
412#define TSEC4_PHYIDX 0
Jon Loeligerd9b94f22005-07-25 14:05:07 -0500413
414/* Options are: eTSEC[0-3] */
415#define CONFIG_ETHPRIME "eTSEC0"
416
417#endif /* CONFIG_TSEC_ENET */
418
419/*
420 * Environment
421 */
422#define CFG_ENV_IS_IN_FLASH 1
423#define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000)
424#define CFG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */
425#define CFG_ENV_SIZE 0x2000
426
427#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
428#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
429
430#if defined(CONFIG_PCI)
431#define CONFIG_COMMANDS (CONFIG_CMD_DFL \
432 | CFG_CMD_PCI \
433 | CFG_CMD_PING \
434 | CFG_CMD_I2C \
435 | CFG_CMD_MII)
436#else
437#define CONFIG_COMMANDS (CONFIG_CMD_DFL \
438 | CFG_CMD_PING \
439 | CFG_CMD_I2C \
440 | CFG_CMD_MII)
441#endif
442#include <cmd_confdefs.h>
443
444#undef CONFIG_WATCHDOG /* watchdog disabled */
445
446/*
447 * Miscellaneous configurable options
448 */
449#define CFG_LONGHELP /* undef to save memory */
450#define CFG_LOAD_ADDR 0x2000000 /* default load address */
451#define CFG_PROMPT "=> " /* Monitor Command Prompt */
452#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
453#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
454#else
455#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
456#endif
457#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
458#define CFG_MAXARGS 16 /* max number of command args */
459#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
460#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */
461
462/*
463 * For booting Linux, the board info and command line data
464 * have to be in the first 8 MB of memory, since this is
465 * the maximum mapped by the Linux kernel during initialization.
466 */
467#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/
468
469/* Cache Configuration */
470#define CFG_DCACHE_SIZE 32768
471#define CFG_CACHELINE_SIZE 32
472#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
473#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/
474#endif
475
476/*
477 * Internal Definitions
478 *
479 * Boot Flags
480 */
481#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
482#define BOOTFLAG_WARM 0x02 /* Software reboot */
483
484#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
485#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
486#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
487#endif
488
489/*
490 * Environment Configuration
491 */
492
493/* The mac addresses for all ethernet interface */
494#if defined(CONFIG_TSEC_ENET)
495#define CONFIG_ETHADDR 00:E0:0C:00:00:FD
496#define CONFIG_HAS_ETH1
497#define CONFIG_ETH1ADDR 00:E0:0C:00:01:FD
498#define CONFIG_HAS_ETH2
499#define CONFIG_ETH2ADDR 00:E0:0C:00:02:FD
Andy Fleming09f3e092006-09-13 10:34:18 -0500500#define CONFIG_HAS_ETH3
501#define CONFIG_ETH3ADDR 00:E0:0C:00:03:FD
Jon Loeligerd9b94f22005-07-25 14:05:07 -0500502#endif
503
504#define CONFIG_IPADDR 192.168.1.253
505
506#define CONFIG_HOSTNAME unknown
507#define CONFIG_ROOTPATH /nfsroot
508#define CONFIG_BOOTFILE your.uImage
509
510#define CONFIG_SERVERIP 192.168.1.1
511#define CONFIG_GATEWAYIP 192.168.1.1
512#define CONFIG_NETMASK 255.255.255.0
513
514#define CONFIG_LOADADDR 200000 /*default location for tftp and bootm*/
515
516#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */
517#undef CONFIG_BOOTARGS /* the boot command will set bootargs*/
518
519#define CONFIG_BAUDRATE 115200
520
521#define CONFIG_EXTRA_ENV_SETTINGS \
522 "netdev=eth0\0" \
523 "consoledev=ttyS1\0" \
Andy Fleming8272dc22006-09-13 10:33:35 -0500524 "ramdiskaddr=600000\0" \
525 "ramdiskfile=your.ramdisk.u-boot\0" \
526 "fdtaddr=400000\0" \
527 "fdtfile=your.fdt.dtb\0"
528
Jon Loeligerd9b94f22005-07-25 14:05:07 -0500529
530#define CONFIG_NFSBOOTCOMMAND \
531 "setenv bootargs root=/dev/nfs rw " \
532 "nfsroot=$serverip:$rootpath " \
533 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
534 "console=$consoledev,$baudrate $othbootargs;" \
535 "tftp $loadaddr $bootfile;" \
Andy Fleming8272dc22006-09-13 10:33:35 -0500536 "tftp $fdtaddr $fdtfile;" \
537 "bootm $loadaddr - $fdtaddr"
538
Jon Loeligerd9b94f22005-07-25 14:05:07 -0500539
540#define CONFIG_RAMBOOTCOMMAND \
541 "setenv bootargs root=/dev/ram rw " \
542 "console=$consoledev,$baudrate $othbootargs;" \
543 "tftp $ramdiskaddr $ramdiskfile;" \
544 "tftp $loadaddr $bootfile;" \
545 "bootm $loadaddr $ramdiskaddr"
546
547#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND
548
549#endif /* __CONFIG_H */