include/configs/db-mv784mp-gp.h

/*
 * Copyright (C) 2014-2015 Stefan Roese <sr@denx.de>
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#ifndef _CONFIG_DB_MV7846MP_GP_H
#define _CONFIG_DB_MV7846MP_GP_H

/*
 * High Level Configuration Options (easy to change)
 */
#define CONFIG_DB_784MP_GP		/* Board target name for DDR training */

#define CONFIG_DISPLAY_BOARDINFO_LATE

/*
 * TEXT_BASE needs to be below 16MiB, since this area is scrubbed
 * for DDR ECC byte filling in the SPL before loading the main
 * U-Boot into it.
 */
#define	CONFIG_SYS_TEXT_BASE	0x00800000
#define CONFIG_SYS_TCLK		250000000	/* 250MHz */

/*
 * Commands configuration
 */
#define CONFIG_SYS_NO_FLASH		/* Declare no flash (NOR/SPI) */
#define CONFIG_CMD_CACHE
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_ENV
#define CONFIG_CMD_EXT2
#define CONFIG_CMD_EXT4
#define CONFIG_CMD_FAT
#define CONFIG_CMD_FS_GENERIC
#define CONFIG_CMD_I2C
#define CONFIG_CMD_NAND
#define CONFIG_CMD_PCI
#define CONFIG_CMD_PING
#define CONFIG_CMD_SATA
#define CONFIG_CMD_SF
#define CONFIG_CMD_SPI
#define CONFIG_CMD_TFTPPUT
#define CONFIG_CMD_TIME

/* I2C */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_MVTWSI
#define CONFIG_I2C_MVTWSI_BASE0		MVEBU_TWSI_BASE
#define CONFIG_SYS_I2C_SLAVE		0x0
#define CONFIG_SYS_I2C_SPEED		100000

/* USB/EHCI configuration */
#define CONFIG_EHCI_IS_TDI
#define CONFIG_USB_MAX_CONTROLLER_COUNT 3

/* SPI NOR flash default params, used by sf commands */
#define CONFIG_SF_DEFAULT_SPEED		1000000
#define CONFIG_SF_DEFAULT_MODE		SPI_MODE_3

/* Environment in SPI NOR flash */
#define CONFIG_ENV_IS_IN_SPI_FLASH
#define CONFIG_ENV_OFFSET		(1 << 20) /* 1MiB in */
#define CONFIG_ENV_SIZE			(64 << 10) /* 64KiB */
#define CONFIG_ENV_SECT_SIZE		(64 << 10) /* 64KiB sectors */

#define CONFIG_PHY_MARVELL		/* there is a marvell phy */
#define PHY_ANEG_TIMEOUT	8000	/* PHY needs a longer aneg time */

#define CONFIG_SYS_CONSOLE_INFO_QUIET	/* don't print console @ startup */
#define CONFIG_SYS_ALT_MEMTEST

/* SATA support */
#define CONFIG_SYS_SATA_MAX_DEVICE	2
#define CONFIG_SATA_MV
#define CONFIG_LIBATA
#define CONFIG_LBA48
#define CONFIG_EFI_PARTITION
#define CONFIG_DOS_PARTITION

/* Additional FS support/configuration */
#define CONFIG_SUPPORT_VFAT

/* PCIe support */
#ifndef CONFIG_SPL_BUILD
#define CONFIG_PCI
#define CONFIG_PCI_MVEBU
#define CONFIG_PCI_PNP
#define CONFIG_PCI_SCAN_SHOW
#endif

/* NAND */
#define CONFIG_SYS_NAND_USE_FLASH_BBT
#define CONFIG_SYS_NAND_ONFI_DETECTION

/*
 * mv-common.h should be defined after CMD configs since it used them
 * to enable certain macros
 */
#include "mv-common.h"

/*
 * Memory layout while starting into the bin_hdr via the
 * BootROM:
 *
 * 0x4000.4000 - 0x4003.4000	headers space (192KiB)
 * 0x4000.4030			bin_hdr start address
 * 0x4003.4000 - 0x4004.7c00	BootROM memory allocations (15KiB)
 * 0x4007.fffc			BootROM stack top
 *
 * The address space between 0x4007.fffc and 0x400f.fff is not locked in
 * L2 cache thus cannot be used.
 */

/* SPL */
/* Defines for SPL */
#define CONFIG_SPL_FRAMEWORK
#define CONFIG_SPL_TEXT_BASE		0x40004030
#define CONFIG_SPL_MAX_SIZE		((128 << 10) - 0x4030)

#define CONFIG_SPL_BSS_START_ADDR	(0x40000000 + (128 << 10))
#define CONFIG_SPL_BSS_MAX_SIZE		(16 << 10)

#ifdef CONFIG_SPL_BUILD
#define CONFIG_SYS_MALLOC_SIMPLE
#endif

#define CONFIG_SPL_STACK		(0x40000000 + ((192 - 16) << 10))
#define CONFIG_SPL_BOOTROM_SAVE		(CONFIG_SPL_STACK + 4)

#define CONFIG_SPL_LIBCOMMON_SUPPORT
#define CONFIG_SPL_LIBGENERIC_SUPPORT
#define CONFIG_SPL_SERIAL_SUPPORT
#define CONFIG_SPL_I2C_SUPPORT

/* SPL related SPI defines */
#define CONFIG_SPL_SPI_SUPPORT
#define CONFIG_SPL_SPI_FLASH_SUPPORT
#define CONFIG_SPL_SPI_LOAD
#define CONFIG_SPL_SPI_BUS		0
#define CONFIG_SPL_SPI_CS		0
#define CONFIG_SYS_SPI_U_BOOT_OFFS	0x20000
#define CONFIG_SYS_U_BOOT_OFFS		CONFIG_SYS_SPI_U_BOOT_OFFS

/* Enable DDR support in SPL (DDR3 training from Marvell bin_hdr) */
#define CONFIG_SPD_EEPROM		0x4e
#define CONFIG_BOARD_ECC_SUPPORT	/* this board supports ECC */

#endif /* _CONFIG_DB_MV7846MP_GP_H */