blob: aeed538fa4e8189d318a4d99b63576e9692ebed0 [file] [log] [blame]
Masahiro Yamada0b11dbf2015-07-26 02:46:26 +09001#
2# Serial device configuration
3#
4
5menu "Serial drivers"
6
Philipp Tomsichf40574e2017-03-17 20:34:53 +01007config BAUDRATE
8 int "Default baudrate"
9 default 115200
10 help
11 Select a default baudrate, where "default" has a driver-specific
12 meaning of either setting the baudrate for the early debug UART
13 in the SPL stage (most drivers) or for choosing a default baudrate
14 in the absence of an environment setting (serial_mxc.c).
15
Hans de Goede8c458582015-08-08 17:45:18 +020016config REQUIRE_SERIAL_CONSOLE
17 bool "Require a serial port for console"
18 # Running without a serial console is not supported by the
19 # non-dm serial code
20 depends on DM_SERIAL
21 default y
22 help
23 Require a serial port for the console, and panic if none is found
24 during serial port initialization (default y). Set this to n on
25 boards which have no debug serial port whatsoever.
26
Simon Glass92c55b62015-12-13 21:36:58 -070027config SERIAL_PRESENT
28 bool "Provide a serial driver"
29 depends on DM_SERIAL
30 default y
31 help
32 In very space-constrained devices even the full UART driver is too
33 large. In this case the debug UART can still be used in some cases.
34 This option enables the full UART in U-Boot, so if is it disabled,
35 the full UART driver will be omitted, thus saving space.
36
37config SPL_SERIAL_PRESENT
38 bool "Provide a serial driver in SPL"
39 depends on DM_SERIAL
40 default y
41 help
42 In very space-constrained devices even the full UART driver is too
43 large. In this case the debug UART can still be used in some cases.
44 This option enables the full UART in SPL, so if is it disabled,
45 the full UART driver will be omitted, thus saving space.
46
Mylène Josserand7095f862017-04-02 12:59:11 +020047config CONS_INDEX
48 int "UART used for console"
49 depends on ARCH_SUNXI
50 default 2 if MACH_SUN5I
Icenowy Zhenge8f86a02017-04-25 01:39:51 +080051 default 5 if MACH_SUN8I_A23 || MACH_SUN8I_A33
Mylène Josserand7095f862017-04-02 12:59:11 +020052 default 1
53 help
54 Configures the console index.
Icenowy Zhenge8f86a02017-04-25 01:39:51 +080055 For Allwinner SoC., default values are 2 for SUN5I and 5 for A23/A33.
Mylène Josserand7095f862017-04-02 12:59:11 +020056 Otherwise, the index equals 1.
57
Masahiro Yamadada333ae2014-10-23 22:26:09 +090058config DM_SERIAL
59 bool "Enable Driver Model for serial drivers"
60 depends on DM
61 help
Simon Glassf94a1be2015-02-05 21:41:35 -070062 Enable driver model for serial. This replaces
63 drivers/serial/serial.c with the serial uclass, which
64 implements serial_putc() etc. The uclass interface is
65 defined in include/serial.h.
Masahiro Yamadaff247b72014-10-23 22:26:11 +090066
Stefan Roese3ca7a062017-08-16 17:37:16 +020067config SERIAL_RX_BUFFER
68 bool "Enable RX buffer for serial input"
69 depends on DM_SERIAL
70 help
71 Enable RX buffer support for the serial driver. This enables
72 pasting longer strings, even when the RX FIFO of the UART is
73 not big enough (e.g. 16 bytes on the normal NS16550).
74
75config SERIAL_RX_BUFFER_SIZE
76 int "RX buffer size"
77 depends on SERIAL_RX_BUFFER
78 default 256
79 help
80 The size of the RX buffer (needs to be power of 2)
81
Simon Glass891f7ae2017-04-02 09:50:32 -060082config SPL_DM_SERIAL
Heiko Schocher04249902017-06-21 06:23:10 +020083 bool "Enable Driver Model for serial drivers in SPL"
Simon Glass891f7ae2017-04-02 09:50:32 -060084 depends on DM_SERIAL
85 default y if SPL && DM_SERIAL
86 help
87 Enable driver model for serial in SPL. This replaces
88 drivers/serial/serial.c with the serial uclass, which
89 implements serial_putc() etc. The uclass interface is
90 defined in include/serial.h.
91
92config TPL_DM_SERIAL
Heiko Schocher04249902017-06-21 06:23:10 +020093 bool "Enable Driver Model for serial drivers in TPL"
Simon Glass891f7ae2017-04-02 09:50:32 -060094 depends on DM_SERIAL
95 default y if TPL && DM_SERIAL
96 help
97 Enable driver model for serial in TPL. This replaces
98 drivers/serial/serial.c with the serial uclass, which
99 implements serial_putc() etc. The uclass interface is
100 defined in include/serial.h.
101
Simon Glass2f964aa2015-01-26 18:27:07 -0700102config DEBUG_UART
103 bool "Enable an early debug UART for debugging"
104 help
105 The debug UART is intended for use very early in U-Boot to debug
106 problems when an ICE or other debug mechanism is not available.
107
108 To use it you should:
109 - Make sure your UART supports this interface
110 - Enable CONFIG_DEBUG_UART
111 - Enable the CONFIG for your UART to tell it to provide this interface
112 (e.g. CONFIG_DEBUG_UART_NS16550)
113 - Define the required settings as needed (see below)
114 - Call debug_uart_init() before use
115 - Call debug_uart_putc() to output a character
116
117 Depending on your platform it may be possible to use this UART before
118 a stack is available.
119
120 If your UART does not support this interface you can probably add
121 support quite easily. Remember that you cannot use driver model and
122 it is preferred to use no stack.
123
124 You must not use this UART once driver model is working and the
125 serial drivers are up and running (done in serial_init()). Otherwise
126 the drivers may conflict and you will get strange output.
127
Simon Glass21d00432015-01-26 18:27:09 -0700128choice
129 prompt "Select which UART will provide the debug UART"
130 depends on DEBUG_UART
Thomas Choub1e361b2015-11-19 21:48:03 +0800131 default DEBUG_UART_NS16550
Simon Glass21d00432015-01-26 18:27:09 -0700132
Thomas Chou220e8022015-10-23 07:36:37 +0800133config DEBUG_UART_ALTERA_JTAGUART
134 bool "Altera JTAG UART"
135 help
136 Select this to enable a debug UART using the altera_jtag_uart driver.
137 You will need to provide parameters to make this work. The driver will
138 be available until the real driver model serial is running.
139
Thomas Chouda2f8382015-10-21 21:26:54 +0800140config DEBUG_UART_ALTERA_UART
141 bool "Altera UART"
142 help
143 Select this to enable a debug UART using the altera_uart driver.
144 You will need to provide parameters to make this work. The driver will
145 be available until the real driver model serial is running.
146
Wills Wang60b49762016-03-16 16:59:57 +0800147config DEBUG_UART_AR933X
148 bool "QCA/Atheros ar933x"
149 depends on AR933X_UART
150 help
151 Select this to enable a debug UART using the ar933x uart driver.
152 You will need to provide parameters to make this work. The
153 driver will be available until the real driver model serial is
154 running.
155
Wenyou Yang998cf3c2016-10-17 09:49:55 +0800156config DEBUG_UART_ATMEL
157 bool "Atmel USART"
158 help
159 Select this to enable a debug UART using the atmel usart driver. You
160 will need to provide parameters to make this work. The driver will
161 be available until the real driver-model serial is running.
162
Álvaro Fernández Rojas30581042017-04-25 00:39:16 +0200163config DEBUG_UART_BCM6345
164 bool "BCM6345 UART"
165 depends on BCM6345_SERIAL
166 help
167 Select this to enable a debug UART on BCM6345 SoCs. You
168 will need to provide parameters to make this work. The driver will
169 be available until the real driver model serial is running.
170
Simon Glass21d00432015-01-26 18:27:09 -0700171config DEBUG_UART_NS16550
172 bool "ns16550"
173 help
174 Select this to enable a debug UART using the ns16550 driver. You
175 will need to provide parameters to make this work. The driver will
176 be available until the real driver model serial is running.
177
Simon Glass275854b2015-08-04 12:33:40 -0600178config DEBUG_EFI_CONSOLE
179 bool "EFI"
180 depends on EFI_APP
181 help
182 Select this to enable a debug console which calls back to EFI to
183 output to the console. This can be useful for early debugging of
184 U-Boot when running on top of EFI (Extensive Firmware Interface).
185 This is a type of BIOS used by PCs.
186
Simon Glassbf6e7022015-07-02 18:15:54 -0600187config DEBUG_UART_S5P
188 bool "Samsung S5P"
189 help
190 Select this to enable a debug UART using the serial_s5p driver. You
191 will need to provide parameters to make this work. The driver will
192 be available until the real driver-model serial is running.
193
Beniamino Galvanibfcef282016-05-08 08:30:16 +0200194config DEBUG_UART_MESON
195 bool "Amlogic Meson"
196 depends on MESON_SERIAL
197 help
198 Select this to enable a debug UART using the serial_meson driver. You
199 will need to provide parameters to make this work. The driver will
200 be available until the real driver-model serial is running.
201
Michal Simek4166ba32015-12-14 16:55:10 +0100202config DEBUG_UART_UARTLITE
203 bool "Xilinx Uartlite"
204 help
205 Select this to enable a debug UART using the serial_uartlite driver.
206 You will need to provide parameters to make this work. The driver will
207 be available until the real driver-model serial is running.
208
Michal Simek966bfa72016-02-23 10:02:28 +0100209config DEBUG_UART_ARM_DCC
210 bool "ARM DCC"
211 help
212 Select this to enable a debug UART using the ARM JTAG DCC port.
213 The DCC port can be used for very early debugging and doesn't require
214 any additional setting like address/baudrate/clock. On systems without
215 any serial interface this is the easiest way how to get console.
216 Every ARM core has own DCC port which is the part of debug interface.
217 This port is available at least on ARMv6, ARMv7, ARMv8 and XScale
218 architectures.
219
Stefan Roese6985d492016-05-17 16:36:00 +0200220config DEBUG_MVEBU_A3700_UART
221 bool "Marvell Armada 3700"
222 help
223 Select this to enable a debug UART using the serial_mvebu driver. You
224 will need to provide parameters to make this work. The driver will
225 be available until the real driver-model serial is running.
226
Simon Glassc54c0a42015-10-17 19:41:22 -0600227config DEBUG_UART_ZYNQ
228 bool "Xilinx Zynq"
229 help
Michal Simek6bf87da2015-12-01 14:29:34 +0100230 Select this to enable a debug UART using the serial_zynq driver. You
Simon Glassc54c0a42015-10-17 19:41:22 -0600231 will need to provide parameters to make this work. The driver will
232 be available until the real driver-model serial is running.
233
Francois Retiefe43ce3f2015-10-29 12:55:34 +0200234config DEBUG_UART_APBUART
235 depends on LEON3
236 bool "Gaisler APBUART"
237 help
238 Select this to enable a debug UART using the serial_leon3 driver. You
239 will need to provide parameters to make this work. The driver will
240 be available until the real driver model serial is running.
241
Sergey Temerkhanov19de8152015-10-14 09:54:24 -0700242config DEBUG_UART_PL010
243 bool "pl010"
244 help
245 Select this to enable a debug UART using the pl01x driver with the
246 PL010 UART type. You will need to provide parameters to make this
247 work. The driver will be available until the real driver model
248 serial is running.
249
250config DEBUG_UART_PL011
251 bool "pl011"
252 help
253 Select this to enable a debug UART using the pl01x driver with the
254 PL011 UART type. You will need to provide parameters to make this
255 work. The driver will be available until the real driver model
256 serial is running.
257
Paul Thacker9e160ee2016-01-28 15:30:14 +0530258config DEBUG_UART_PIC32
259 bool "Microchip PIC32"
260 depends on PIC32_SERIAL
261 help
262 Select this to enable a debug UART using the serial_pic32 driver. You
263 will need to provide parameters to make this work. The driver will
264 be available until the real driver model serial is running.
265
Jagan Teki61366b72017-06-06 05:31:51 +0000266config DEBUG_UART_MXC
267 bool "IMX Serial port"
268 depends on MXC_UART
269 help
270 Select this to enable a debug UART using the serial_mxc driver. You
271 will need to provide parameters to make this work. The driver will
272 be available until the real driver model serial is running.
273
Masahiro Yamadad5cf3292016-03-18 16:41:52 +0900274config DEBUG_UART_UNIPHIER
275 bool "UniPhier on-chip UART"
276 depends on ARCH_UNIPHIER
277 help
278 Select this to enable a debug UART using the UniPhier on-chip UART.
279 You will need to provide DEBUG_UART_BASE to make this work. The
280 driver will be available until the real driver-model serial is
281 running.
282
Lokesh Vutlaa52cf082017-04-22 15:57:25 +0530283config DEBUG_UART_OMAP
284 bool "OMAP uart"
285 help
286 Select this to enable a debug UART using the omap ns16550 driver.
287 You will need to provide parameters to make this work. The driver
288 will be available until the real driver model serial is running.
289
Simon Glass21d00432015-01-26 18:27:09 -0700290endchoice
291
Simon Glass2f964aa2015-01-26 18:27:07 -0700292config DEBUG_UART_BASE
293 hex "Base address of UART"
294 depends on DEBUG_UART
295 help
296 This is the base address of your UART for memory-mapped UARTs.
297
298 A default should be provided by your board, but if not you will need
299 to use the correct value here.
300
301config DEBUG_UART_CLOCK
302 int "UART input clock"
303 depends on DEBUG_UART
304 help
305 The UART input clock determines the speed of the internal UART
306 circuitry. The baud rate is derived from this by dividing the input
307 clock down.
308
309 A default should be provided by your board, but if not you will need
310 to use the correct value here.
311
Simon Glassdd0b0122015-02-27 22:06:25 -0700312config DEBUG_UART_SHIFT
313 int "UART register shift"
314 depends on DEBUG_UART
315 default 0 if DEBUG_UART
316 help
317 Some UARTs (notably ns16550) support different register layouts
318 where the registers are spaced either as bytes, words or some other
319 value. Use this value to specify the shift to use, where 0=byte
320 registers, 2=32-bit word registers, etc.
321
Simon Glass0e977bc2015-10-18 19:51:24 -0600322config DEBUG_UART_BOARD_INIT
323 bool "Enable board-specific debug UART init"
324 depends on DEBUG_UART
325 help
326 Some boards need to set things up before the debug UART can be used.
327 On these boards a call to debug_uart_init() is insufficient. When
328 this option is enabled, the function board_debug_uart_init() will
329 be called when debug_uart_init() is called. You can put any code
330 here that is needed to set up the UART ready for use, such as set
331 pin multiplexing or enable clocks.
332
Simon Glassc7fefcb2015-10-18 19:51:25 -0600333config DEBUG_UART_ANNOUNCE
334 bool "Show a message when the debug UART starts up"
335 depends on DEBUG_UART
336 help
337 Enable this option to show a message when the debug UART is ready
338 for use. You will see a message like "<debug_uart> " as soon as
339 U-Boot has the UART ready for use (i.e. your code calls
340 debug_uart_init()). This can be useful just as a check that
341 everything is working.
342
Sergey Temerkhanov19de8152015-10-14 09:54:24 -0700343config DEBUG_UART_SKIP_INIT
344 bool "Skip UART initialization"
345 help
346 Select this if the UART you want to use for debug output is already
347 initialized by the time U-Boot starts its execution.
348
Thomas Chou220e8022015-10-23 07:36:37 +0800349config ALTERA_JTAG_UART
350 bool "Altera JTAG UART support"
351 depends on DM_SERIAL
352 help
353 Select this to enable an JTAG UART for Altera devices.The JTAG UART
354 core implements a method to communicate serial character streams
355 between a host PC and a Qsys system on an Altera FPGA. Please find
356 details on the "Embedded Peripherals IP User Guide" of Altera.
357
358config ALTERA_JTAG_UART_BYPASS
359 bool "Bypass output when no connection"
360 depends on ALTERA_JTAG_UART
361 help
362 Bypass console output and keep going even if there is no JTAG
363 terminal connection with the host. The console output will resume
364 once the JTAG terminal is connected. Without the bypass, the console
365 output will wait forever until a JTAG terminal is connected. If you
366 not are sure, say Y.
367
Thomas Chouda2f8382015-10-21 21:26:54 +0800368config ALTERA_UART
369 bool "Altera UART support"
370 depends on DM_SERIAL
371 help
372 Select this to enable an UART for Altera devices. Please find
373 details on the "Embedded Peripherals IP User Guide" of Altera.
374
Wills Wang60b49762016-03-16 16:59:57 +0800375config AR933X_UART
376 bool "QCA/Atheros ar933x UART support"
377 depends on DM_SERIAL && SOC_AR933X
378 help
379 Select this to enable UART support for QCA/Atheros ar933x
380 devices. This driver uses driver model and requires a device
381 tree binding to operate, please refer to the document at
382 doc/device-tree-bindings/serial/qca,ar9330-uart.txt.
383
Wenyou Yang6ec739a2016-10-17 09:49:54 +0800384config ATMEL_USART
385 bool "Atmel USART support"
386 help
387 Select this to enable USART support for Atmel SoCs. It can be
388 configured in the device tree, and input clock frequency can
389 be got from the clk node.
390
Álvaro Fernández Rojas30581042017-04-25 00:39:16 +0200391config BCM6345_SERIAL
392 bool "Support for BCM6345 UART"
393 depends on DM_SERIAL && ARCH_BMIPS
394 help
395 Select this to enable UART on BCM6345 SoCs.
396
Bin Meng5ed07cf2016-01-13 19:39:00 -0800397config FSL_LPUART
398 bool "Freescale LPUART support"
399 help
400 Select this to enable a Low Power UART for Freescale VF610 and
401 QorIQ Layerscape devices.
402
Stefan Roese6985d492016-05-17 16:36:00 +0200403config MVEBU_A3700_UART
404 bool "UART support for Armada 3700"
405 default n
406 help
407 Choose this option to add support for UART driver on the Marvell
408 Armada 3700 SoC. The base address is configured via DT.
409
Jagan Teki8829e662016-10-08 18:00:08 +0530410config MXC_UART
411 bool "IMX serial port support"
Patrick Bruenn98d62e62016-11-04 11:57:02 +0100412 depends on MX5 || MX6
Jagan Teki8829e662016-10-08 18:00:08 +0530413 help
414 If you have a machine based on a Motorola IMX CPU you
415 can enable its onboard serial port by enabling this option.
416
Paul Thacker9e160ee2016-01-28 15:30:14 +0530417config PIC32_SERIAL
418 bool "Support for Microchip PIC32 on-chip UART"
419 depends on DM_SERIAL && MACH_PIC32
420 default y
421 help
422 Support for the UART found on Microchip PIC32 SoC's.
423
Thomas Chou9e390032015-11-19 21:48:14 +0800424config SYS_NS16550
425 bool "NS16550 UART or compatible"
426 help
427 Support NS16550 UART or compatible. This can be enabled in the
428 device tree with the correct input clock frequency. If the input
429 clock frequency is not defined in the device tree, the macro
430 CONFIG_SYS_NS16550_CLK defined in a legacy board header file will
431 be used. It can be a constant or a function to get clock, eg,
432 get_serial_clock().
433
Andy Shevchenkoc5f8dd42017-02-28 14:04:10 +0200434config INTEL_MID_SERIAL
435 bool "Intel MID platform UART support"
436 depends on DM_SERIAL && OF_CONTROL
437 depends on INTEL_MID
438 select SYS_NS16550
439 help
440 Select this to enable a UART for Intel MID platforms.
441 This uses the ns16550 driver as a library.
442
Simon Glass2fc24d52016-07-04 11:58:24 -0600443config ROCKCHIP_SERIAL
444 bool "Rockchip on-chip UART support"
445 depends on DM_SERIAL && SPL_OF_PLATDATA
446 help
447 Select this to enable a debug UART for Rockchip devices when using
Tom Rini7f73ca42017-01-14 12:20:23 -0500448 CONFIG_SPL_OF_PLATDATA (i.e. a compiled-in device tree replacemenmt).
Simon Glass2fc24d52016-07-04 11:58:24 -0600449 This uses the ns16550 driver, converting the platdata from of-platdata
450 to the ns16550 format.
451
Simon Glassaf282242015-03-06 13:19:03 -0700452config SANDBOX_SERIAL
453 bool "Sandbox UART support"
Masahiro Yamada2ea65f32015-08-28 20:14:21 +0900454 depends on SANDBOX
Simon Glassaf282242015-03-06 13:19:03 -0700455 help
456 Select this to enable a seral UART for sandbox. This is required to
457 operate correctly, otherwise you will see no serial output from
458 sandbox. The emulated UART will display to the console and console
459 input will be fed into the UART. This allows you to interact with
460 U-Boot.
461
462 The operation of the console is controlled by the -t command-line
463 flag. In raw mode, U-Boot sees all characters from the terminal
464 before they are processed, including Ctrl-C. In cooked mode, Ctrl-C
465 is processed by the terminal, and terminates U-Boot. Valid options
466 are:
467
468 -t raw-with-sigs Raw mode, Ctrl-C will terminate U-Boot
469 -t raw Raw mode, Ctrl-C is processed by U-Boot
470 -t cooked Cooked mode, Ctrl-C terminates
471
Marek Vasut03a38a32017-07-21 23:18:46 +0200472config SCIF_CONSOLE
473 bool "Renesas SCIF UART support"
474 depends on SH || ARCH_RMOBILE
475 help
476 Select this to enable Renesas SCIF UART. To operate serial ports
477 on systems with RCar or SH SoCs, say Y to this option. If unsure,
478 say N.
479
Masahiro Yamadaff247b72014-10-23 22:26:11 +0900480config UNIPHIER_SERIAL
Masahiro Yamadab6ef3a32015-05-29 17:30:01 +0900481 bool "Support for UniPhier on-chip UART"
Masahiro Yamada2ea65f32015-08-28 20:14:21 +0900482 depends on ARCH_UNIPHIER
Masahiro Yamada85dc2fe2016-08-25 19:00:37 +0900483 default y
Masahiro Yamadaff247b72014-10-23 22:26:11 +0900484 help
Masahiro Yamadab6ef3a32015-05-29 17:30:01 +0900485 If you have a UniPhier based board and want to use the on-chip
486 serial ports, say Y to this option. If unsure, say N.
Simon Glassdcfe4a52015-07-27 15:47:23 -0600487
Michal Simek54e24d32015-12-09 12:50:05 +0100488config XILINX_UARTLITE
489 bool "Xilinx Uarlite support"
Ricardo Ribalda Delgado80cce262016-01-26 11:24:19 +0100490 depends on DM_SERIAL && (MICROBLAZE || ARCH_ZYNQ || ARCH_ZYNQMP || 4xx)
Michal Simek54e24d32015-12-09 12:50:05 +0100491 help
492 If you have a Xilinx based board and want to use the uartlite
493 serial ports, say Y to this option. If unsure, say N.
494
Beniamino Galvanibfcef282016-05-08 08:30:16 +0200495config MESON_SERIAL
496 bool "Support for Amlogic Meson UART"
497 depends on DM_SERIAL && ARCH_MESON
498 help
499 If you have an Amlogic Meson based board and want to use the on-chip
500 serial ports, say Y to this option. If unsure, say N.
501
Mateusz Kulikowski142a20c2016-03-31 23:12:14 +0200502config MSM_SERIAL
503 bool "Qualcomm on-chip UART"
504 depends on DM_SERIAL
505 help
506 Support Data Mover UART used on Qualcomm Snapdragon SoCs.
507 It should support all Qualcomm devices with UARTDM version 1.4,
508 for example APQ8016 and MSM8916.
509 Single baudrate is supported in current implementation (115200).
Stefan Roese6985d492016-05-17 16:36:00 +0200510
Marcel Ziswilerd804a5e2016-11-14 21:40:25 +0100511config PXA_SERIAL
512 bool "PXA serial port support"
513 help
514 If you have a machine based on a Marvell XScale PXA2xx CPU you
515 can enable its onboard serial ports by enabling this option.
516
Patrice Chotard214a17e2017-02-21 13:37:07 +0100517config STI_ASC_SERIAL
518 bool "STMicroelectronics on-chip UART"
519 depends on DM_SERIAL && ARCH_STI
520 help
521 Select this to enable Asynchronous Serial Controller available
522 on STiH410 SoC. This is a basic implementation, it supports
523 following baudrate 9600, 19200, 38400, 57600 and 115200.
524
Patrice Chotard84e9dcc2017-07-26 15:48:39 +0200525config STM32X7_SERIAL
526 bool "STMicroelectronics STM32 SoCs on-chip UART"
527 depends on DM_SERIAL && STM32F7
528 help
529 If you have a machine based on a STM32 F7 you can enable its
530 onboard serial ports, say Y to this option. If unsure, say N.
531
Christophe Leroydd7ff472017-07-06 10:33:27 +0200532config MPC8XX_CONS
533 bool "Console driver for MPC8XX"
534 depends on 8xx
535 default y
536
537choice
538 prompt "Console port"
539 default 8xx_CONS_SMC1
540 depends on MPC8XX_CONS
541 help
542 Depending on board, select one serial port
543 (CONFIG_8xx_CONS_SMC1 or CONFIG_8xx_CONS_SMC2)
544
545config 8xx_CONS_SMC1
546 bool "SMC1"
547
548config 8xx_CONS_SMC2
549 bool "SMC2"
550
551endchoice
552
553config SYS_SMC_RXBUFLEN
554 int "Console Rx buffer length"
555 depends on MPC8XX_CONS
556 default 1
557 help
558 With CONFIG_SYS_SMC_RXBUFLEN it is possible to define
559 the maximum receive buffer length for the SMC.
560 This option is actual only for 8xx possible.
561 If using CONFIG_SYS_SMC_RXBUFLEN also CONFIG_SYS_MAXIDLE
562 must be defined, to setup the maximum idle timeout for
563 the SMC.
564
565config SYS_MAXIDLE
566 int "maximum idle timeout"
567 depends on MPC8XX_CONS
568 default 0
569
570config SYS_BRGCLK_PRESCALE
571 int "BRG Clock Prescale"
572 depends on MPC8XX_CONS
573 default 1
574
575config SYS_SDSR
576 hex "SDSR Value"
577 depends on MPC8XX_CONS
578 default 0x83
579
580config SYS_SDMR
581 hex "SDMR Value"
582 depends on MPC8XX_CONS
583 default 0
584
Masahiro Yamada0b11dbf2015-07-26 02:46:26 +0900585endmenu