blob: 6a1ffa17d0435c17060817e8744bd891578b504c [file] [log] [blame]
Mike Frysingerd4d77302008-02-04 19:26:55 -05001/*
2 * blackfin-config-post.h - setup common defines for Blackfin boards based on config.h
3 *
4 * Copyright (c) 2007 Analog Devices Inc.
5 *
6 * Licensed under the GPL-2 or later.
7 */
8
9#ifndef __ASM_BLACKFIN_CONFIG_POST_H__
10#define __ASM_BLACKFIN_CONFIG_POST_H__
11
12/* Check to make sure everything fits in external RAM */
13#if ((CFG_MONITOR_BASE + CFG_MONITOR_LEN) > CFG_MAX_RAM_SIZE)
14# error Memory Map does not fit into configuration
15#endif
16
Mike Frysinger9171fc82008-03-30 15:46:13 -040017/* Sanity check CONFIG_BFIN_CPU */
18#ifndef CONFIG_BFIN_CPU
19# error CONFIG_BFIN_CPU: your board config needs to define this
Mike Frysingerd4d77302008-02-04 19:26:55 -050020#endif
21
22/* Make sure the structure is properly aligned */
23#if ((CFG_GBL_DATA_ADDR & -4) != CFG_GBL_DATA_ADDR)
24# error CFG_GBL_DATA_ADDR: must be 4 byte aligned
25#endif
26
27/* Set default CONFIG_VCO_HZ if need be */
28#if !defined(CONFIG_VCO_HZ)
29# if (CONFIG_CLKIN_HALF == 0)
30# define CONFIG_VCO_HZ (CONFIG_CLKIN_HZ * CONFIG_VCO_MULT)
31# else
32# define CONFIG_VCO_HZ ((CONFIG_CLKIN_HZ * CONFIG_VCO_MULT) / 2)
33# endif
34#endif
35
36/* Set default CONFIG_CCLK_HZ if need be */
37#if !defined(CONFIG_CCLK_HZ)
38# if (CONFIG_PLL_BYPASS == 0)
39# define CONFIG_CCLK_HZ (CONFIG_VCO_HZ / CONFIG_CCLK_DIV)
40# else
41# define CONFIG_CCLK_HZ CONFIG_CLKIN_HZ
42# endif
43#endif
44
45/* Set default CONFIG_SCLK_HZ if need be */
46#if !defined(CONFIG_SCLK_HZ)
47# if (CONFIG_PLL_BYPASS == 0)
48# define CONFIG_SCLK_HZ (CONFIG_VCO_HZ / CONFIG_SCLK_DIV)
49# else
50# define CONFIG_SCLK_HZ CONFIG_CLKIN_HZ
51# endif
52#endif
53
54/* Since we use these to program PLL registers directly,
55 * make sure the values are sane and won't screw us up.
56 */
57#if (CONFIG_VCO_MULT & 0x3F) != CONFIG_VCO_MULT
58# error CONFIG_VCO_MULT: Invalid value: must fit in 6 bits (0 - 63)
59#endif
60#if (CONFIG_CLKIN_HALF & 0x1) != CONFIG_CLKIN_HALF
61# error CONFIG_CLKIN_HALF: Invalid value: must be 0 or 1
62#endif
63#if (CONFIG_PLL_BYPASS & 0x1) != CONFIG_PLL_BYPASS
64# error CONFIG_PLL_BYPASS: Invalid value: must be 0 or 1
65#endif
66
67/* Using L1 scratch pad makes sense for everyone by default. */
68#ifndef CMD_LINE_ADDR
69# define CMD_LINE_ADDR L1_SRAM_SCRATCH
70#endif
71
72#endif