blob: 888657cb0c79f6c9447fff876315049aeb73a61e [file] [log] [blame]
Tim Harvey59189a82014-03-06 07:46:30 -08001U-Boot for the Gateworks Ventana Product Family boards
2
3This file contains information for the port of U-Boot to the Gateworks
4Ventana Product family boards.
5
Tim Harvey0cc11de2014-06-02 16:13:27 -070061. Secondary Program Loader (SPL)
7---------------------------------
8
9The i.MX6 has a BOOT ROM PPL (Primary Program Loader) which supports loading
10an executable image from various boot devices.
11
12The Gateworks Ventana board config uses an SPL build configuration. This
13will build the following artifacts from u-boot source:
14 - SPL - Secondary Program Loader that the i.MX6 BOOT ROM (Primary Program
15 Loader) boots. This detects CPU/DRAM configuration, configures
16 The DRAM controller, loads u-boot.img from the detected boot device,
17 and jumps to it. As this is booted from the PPL, it has an IVT/DCD
18 table.
19 - u-boot.img - The main u-boot core which is u-boot.bin with a image header.
20
21
222. Build
23--------
24
25To build U-Boot for the Gateworks Ventana product family:
26
27 make gwventana_config
28 make
29
30
313. Boot source, boot from NAND
Tim Harvey59189a82014-03-06 07:46:30 -080032------------------------------
33
34The i.MX6 BOOT ROM expects some structures that provide details of NAND layout
35and bad block information (referred to as 'bootstreams') which are replicated
Tim Harvey0cc11de2014-06-02 16:13:27 -070036multiple times in NAND. The number of replications and their spacing (referred
37to as search stride) is configurable through board strapping options and/or
38eFUSE settings (BOOT_SEARCH_COUNT / Pages in block from BOOT_CFG2). In
39addition, the i.MX6 BOOT ROM Flash Configuration Block (FCB) supports two
40copies of a bootloader in flash in the case that a bad block has corrupted one.
41The Freescale 'kobs-ng' application from the Freescale LTIB BSP, which runs
42under Linux and operates on an MTD partition, must be used to program the
43bootstream in order to setup this flash structure correctly.
Tim Harvey59189a82014-03-06 07:46:30 -080044
45The Gateworks Ventana boards with NAND flash have been factory programmed
46such that their eFUSE settings expect 2 copies of the boostream (this is
47specified by providing kobs-ng with the --search_exponent=1 argument). Once in
Tim Harvey0cc11de2014-06-02 16:13:27 -070048Linux with MTD support for the NAND on /dev/mtd0 you can program the SPL
Tim Harvey59189a82014-03-06 07:46:30 -080049with:
50
Tim Harvey0cc11de2014-06-02 16:13:27 -070051kobs-ng init -v -x --search_exponent=1 SPL
Tim Harvey59189a82014-03-06 07:46:30 -080052
Tim Harvey0cc11de2014-06-02 16:13:27 -070053The kobs-ng application uses an imximage which contains the Image Vector Table
54(IVT) and Device Configuration Data (DCD) structures that the i.MX6 BOOT ROM
55requires to boot. The kobs-ng adds the Firmware Configuration Block (FCB) and
56Discovered Bad Block Table (DBBT). The SPL build artifact from u-boot is
57an imximage.
58
59The u-boot.img, which is the non SPL u-boot binary appended to a u-boot image
60header must be programmed in the NAND flash boot device at an offset hard
61coded in the SPL. For the Ventana boards, this has been chosen to be 14MB.
62The image can be programmed from either u-boot or Linux:
63
64u-boot:
65Ventana > setenv mtdparts mtdparts=nand:14m(spl),2m(uboot),1m(env),-(rootfs)
66Ventana > tftp ${loadaddr} u-boot.img && nand erase.part uboot && \
67 nand write ${loadaddr} uboot ${filesize}
68
69Linux:
70nandwrite /dev/mtd1 u-boot.img
71
72The above assumes the default Ventana partitioning scheme which is configured
73via the mtdparts env var:
74 - spl: 14MB
75 - uboot: 2M
76 - env: 1M
77 - rootfs: the rest
Tim Harvey59189a82014-03-06 07:46:30 -080078
79This information is taken from:
80 http://trac.gateworks.com/wiki/ventana/bootloader#NANDFLASH
81
82More details about the i.MX6 BOOT ROM can be found in the IMX6 reference manual.
83