blob: c9ef6e6c81673579d9db1c1daf6c2331fa75d084 [file] [log] [blame]
wdenk028ab6b2004-02-23 23:54:43 +00001Xilinx ML300 platform
2=====================
3
40. Introduction
5---------------
6
7The Xilinx ML300 board is based on the Virtex-II Pro FPGA with
8integrated IBM PowerPC 405 core. The board is normally booted from
9System ACE CF. U-Boot is then run out of main memory.
10
11An FPGA is a configurable and thus very flexible device. To
12accommodate for this flexibility this port of U-Boot includes the
13required means to regenerate the drivers and configuration files if
14you decide to change the hardware design. The required steps are
15described below.
16
17
181. Requirements
19---------------
20
21To compile and run U-Boot on the Xilinx ML300 platform you need the
22following items.
23
24- A Xilinx ML300 platform (see http://www.xilinx.com/ml300)
25- EDK and ISE development tools (shipping with ML300)
26- Parallel4 cable (shipping with ML300)
27- The EDK reference design for ML300. You can get this as design #6 from
28 http://www.xilinx.com/ise/embedded/edk_examples.htm
29- A BOOTP/TFTP server
30
31
322. Quick Start
33--------------
34
35To compile and run U-Boot on ML300 follow the steps below. Make sure
36to consult the documentation for U-Boot, EDK, and the EDK reference
37design for ML300 if you have any questions.
38
391. Implement the EDK reference design for ML300. You can use any of
40 the project files, for example from a xygwin shell:
41 $ xps -nw system_linux.xmp
42 XPS% run init_bram
432. Configure and compile U-Boot. Change into the root directory of
44 U-Boot and run:
45 $ export CROSS_COMPILE=powerpc-eabi-
46 $ make ml300_config
47 $ make
483. Set up the ML300, connect the Parallel4 and the serial cable. Start
49 a terminal on your host computer and set the communication
50 parameters to 9600,8N1,no handshake.
514. Set up the BOOTP/TFTP server on your host machine. U-Boot is
52 preconfigured to use a fixed HW MAC address of 00:0A:35:00:22:01.
535. Download the bitstream to the ML300.
546. Use XMD to download and run U-Boot on the ML300:
55 $ xmd
56 XMD% ppcconnect
57 XMD% dow u-boot
58 XMD% run
59
60You can now make an ACE file out of bitstream and U-Boot:
61 $ xmd genace.tcl -jprog -board ml300 -hw \
62 implementation/download.bit -elf u-boot -ace top.ace
63
64Put the ACE file onto the MicroDrive, for example into xilinx/myace,
65and reboot ML300.
66
67
683. Generating a Custom BSP for U-Boot
69-------------------------------------
70
71If you decide to change the EDK reference design for ML300 or if you
72build a new design from scratch either with the Base System Builder in
73XPS or all by hand you most likely will change the base addresses for
74the Uart and the Ethernet peripheral. If you do so you will have two
75options:
76
771. Edit boards/xilinx/ml300/xparameters.h to reflect the changes you
78 made to your hardware.
792. Use the MLD technology provided by Xilinx Platform Studio to make
80 the changes automatically. To do so go to the root directory of the
81 EDK reference design for ML300. Copy the Linux project file and the
82 Linux software configuration file:
83 $ cp system_linux.xmp system_uboot.xmp
84 $ cp system_linux.mss system_uboot.mss
85
86 Edit system_uboot.xmp and and have it point to system_uboot.mss for
87 the software configuration.
88
89 Then, copy the sw_services directory in
90 boards/xilinx/ml300/sw_services to the root directory of the EDK
91 reference design for ML300.
92 $ cp -R <uboot dir>/boards/xilinx/ml300/sw_services <edk dir>
93
94 Modify system_uboot.mss. Look for the Linux library definition
95 and change it to generate a BSP for U-Boot. An example, might look
96 like this:
97
98 BEGIN LIBRARY
99 PARAMETER LIBRARY_NAME = uboot
100 PARAMETER LIBRARY_VER = 1.00.a
101 PARAMETER CONNECTED_PERIPHS = (opb_uart16550_0,opb_ethernet_0)
102 PARAMETER TARGET_DIR = <uboot dir>
103 END
104
105 Now, you are ready to generate the Xilinx ML300 BSP for U-Boot:
106 $ xps -nw system_uboot.xmp
107 XPS% run libs
108
109 If all goes well the new configuration has been copied into the
110 right places within the U-Boot source tree. Recompile U-Boot and
111 run it on the ML300.
112
113
1144. ToDo
115-------
116
117- Add support for all other peripherals on ML300.
118- Read the MAC address out of the IIC EEPROM.
119- Store the bootargs in the IIC EEPROM.
120
121
1225. References
123-------------
124
125ML300: http://www.xilinx.com/ml300
126EDK: http://www.xilinx.com/edk
127ISE: http://www.xilinx.com/ise
128Reference Design: http://www.xilinx.com/ise/embedded/edk_examples.htm