include/configs/cyrus.h - github/trini/u-boot - Gitiles

 /*
  * Based on corenet_ds.h
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */

 #ifndef __CONFIG_H
 #define __CONFIG_H

 #if !defined(CONFIG_ARCH_P5020) && !defined(CONFIG_ARCH_P5040)
 #error Must call Cyrus CONFIG with a specific CPU enabled.
 #endif

 #define CONFIG_SDCARD
 #define CONFIG_FSL_SATA_V2
 #define CONFIG_PCIE3
 #define CONFIG_PCIE4
 #ifdef CONFIG_ARCH_P5020
 #define CONFIG_SYS_FSL_RAID_ENGINE
 #define CONFIG_SYS_DPAA_RMAN
 #endif
 #define CONFIG_SYS_DPAA_PME

 /*
  * Corenet DS style board configuration file
  */
 #define CONFIG_RAMBOOT_TEXT_BASE	CONFIG_SYS_TEXT_BASE
 #define CONFIG_RESET_VECTOR_ADDRESS	0xfffffffc
 #define CONFIG_SYS_FSL_PBL_PBI board/varisys/cyrus/pbi.cfg
 #if defined(CONFIG_ARCH_P5020)
 #define CONFIG_SYS_CLK_FREQ 133000000
 #define CONFIG_SYS_FSL_PBL_RCW board/varisys/cyrus/rcw_p5020_v2.cfg
 #elif defined(CONFIG_ARCH_P5040)
 #define CONFIG_SYS_CLK_FREQ 100000000
 #define CONFIG_SYS_FSL_PBL_RCW board/varisys/cyrus/rcw_p5040.cfg
 #endif

 /* High Level Configuration Options */
 #define CONFIG_SYS_BOOK3E_HV		/* Category E.HV supported */
 #define CONFIG_MP			/* support multiple processors */

 #define CONFIG_SYS_MMC_MAX_DEVICE     1

 #ifndef CONFIG_SYS_TEXT_BASE
 #define CONFIG_SYS_TEXT_BASE	0xeff40000
 #endif

 #define CONFIG_SYS_FSL_CPC		/* Corenet Platform Cache */
 #define CONFIG_SYS_NUM_CPC		CONFIG_SYS_NUM_DDR_CTLRS
 #define CONFIG_PCIE1			/* PCIE controller 1 */
 #define CONFIG_PCIE2			/* PCIE controller 2 */
 #define CONFIG_FSL_PCI_INIT		/* Use common FSL init code */
 #define CONFIG_SYS_PCI_64BIT		/* enable 64-bit PCI resources */

 #define CONFIG_ENV_OVERWRITE

 #if defined(CONFIG_SDCARD)
 #define CONFIG_SYS_EXTRA_ENV_RELOC
 #define CONFIG_FSL_FIXED_MMC_LOCATION
 #define CONFIG_SYS_MMC_ENV_DEV          0
 #define CONFIG_ENV_SIZE			0x2000
 #define CONFIG_ENV_OFFSET		(512 * 1658)
 #endif

 /*
  * These can be toggled for performance analysis, otherwise use default.
  */
 #define CONFIG_SYS_CACHE_STASHING
 #define CONFIG_BACKSIDE_L2_CACHE
 #define CONFIG_SYS_INIT_L2CSR0		L2CSR0_L2E
 #define CONFIG_BTB			/* toggle branch predition */
 #define	CONFIG_DDR_ECC
 #ifdef CONFIG_DDR_ECC
 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
 #define CONFIG_MEM_INIT_VALUE		0xdeadbeef
 #endif

 #define CONFIG_ENABLE_36BIT_PHYS

 #ifdef CONFIG_PHYS_64BIT
 #define CONFIG_ADDR_MAP
 #define CONFIG_SYS_NUM_ADDR_MAP		64	/* number of TLB1 entries */
 #endif

 /* test POST memory test */
 #undef CONFIG_POST
 #define CONFIG_SYS_MEMTEST_START	0x00200000	/* memtest works on */
 #define CONFIG_SYS_MEMTEST_END		0x00400000
 #define CONFIG_SYS_ALT_MEMTEST

 /*
  *  Config the L3 Cache as L3 SRAM
  */
 #define CONFIG_SYS_INIT_L3_ADDR		CONFIG_RAMBOOT_TEXT_BASE
 #ifdef CONFIG_PHYS_64BIT
 #define CONFIG_SYS_INIT_L3_ADDR_PHYS	(0xf00000000ull | CONFIG_RAMBOOT_TEXT_BASE)
 #else
 #define CONFIG_SYS_INIT_L3_ADDR_PHYS	CONFIG_SYS_INIT_L3_ADDR
 #endif
 #define CONFIG_SYS_L3_SIZE		(1024 << 10)
 #define CONFIG_SYS_INIT_L3_END (CONFIG_SYS_INIT_L3_ADDR + CONFIG_SYS_L3_SIZE)

 #ifdef CONFIG_PHYS_64BIT
 #define CONFIG_SYS_DCSRBAR		0xf0000000
 #define CONFIG_SYS_DCSRBAR_PHYS		0xf00000000ull
 #endif

 /*
  * DDR Setup
  */
 #define CONFIG_VERY_BIG_RAM
 #define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000
 #define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE

 #define CONFIG_DIMM_SLOTS_PER_CTLR	1
 #define CONFIG_CHIP_SELECTS_PER_CTRL	(4 * CONFIG_DIMM_SLOTS_PER_CTLR)

 #define CONFIG_DDR_SPD

 #define CONFIG_SYS_SPD_BUS_NUM	1
 #define SPD_EEPROM_ADDRESS1	0x51
 #define SPD_EEPROM_ADDRESS2	0x52
 #define CONFIG_SYS_SDRAM_SIZE	4096	/* for fixed parameter use */

 /*
  * Local Bus Definitions
  */

 #define CONFIG_SYS_LBC0_BASE		0xe0000000 /* Start of LBC Registers */
 #ifdef CONFIG_PHYS_64BIT
 #define CONFIG_SYS_LBC0_BASE_PHYS	0xfe0000000ull
 #else
 #define CONFIG_SYS_LBC0_BASE_PHYS	CONFIG_SYS_LBC0_BASE
 #endif

 #define CONFIG_SYS_LBC1_BASE		0xe1000000 /* Start of LBC Registers */
 #ifdef CONFIG_PHYS_64BIT
 #define CONFIG_SYS_LBC1_BASE_PHYS	0xfe1000000ull
 #else
 #define CONFIG_SYS_LBC1_BASE_PHYS	CONFIG_SYS_LBC1_BASE
 #endif

 /* Set the local bus clock 1/16 of platform clock */
 #define CONFIG_SYS_LBC_LCRR		(LCRR_CLKDIV_16 | LCRR_EADC_1)

 #define CONFIG_SYS_BR0_PRELIM \
 (BR_PHYS_ADDR(CONFIG_SYS_LBC0_BASE_PHYS) | BR_PS_16 | BR_V)
 #define CONFIG_SYS_BR1_PRELIM \
 (BR_PHYS_ADDR(CONFIG_SYS_LBC1_BASE_PHYS) | BR_PS_16 | BR_V)

 #define CONFIG_SYS_OR0_PRELIM	0xfff00010
 #define CONFIG_SYS_OR1_PRELIM	0xfff00010

 #define CONFIG_SYS_MONITOR_BASE		CONFIG_SYS_TEXT_BASE	/* start of monitor */

 #if defined(CONFIG_RAMBOOT_PBL)
 #define CONFIG_SYS_RAMBOOT
 #endif

 #define CONFIG_BOARD_EARLY_INIT_R	/* call board_early_init_r function */
 #define CONFIG_MISC_INIT_R

 #define CONFIG_HWCONFIG

 /* define to use L1 as initial stack */
 #define CONFIG_L1_INIT_RAM
 #define CONFIG_SYS_INIT_RAM_LOCK
 #define CONFIG_SYS_INIT_RAM_ADDR	0xfdd00000	/* Initial L1 address */
 #ifdef CONFIG_PHYS_64BIT
 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf
 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR
 /* The assembler doesn't like typecast */
 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
 	((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
 	  CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
 #else
 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS	CONFIG_SYS_INIT_RAM_ADDR /* Initial L1 address */
 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0
 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS
 #endif
 #define CONFIG_SYS_INIT_RAM_SIZE		0x00004000	/* Size of used area in RAM */

 #define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET

 #define CONFIG_SYS_MONITOR_LEN		(768 * 1024)
 #define CONFIG_SYS_MALLOC_LEN		(1024 * 1024)	/* Reserved for malloc */

 /* Serial Port - controlled on board with jumper J8
  * open - index 2
  * shorted - index 1
  */
 #define CONFIG_CONS_INDEX	1
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE	1
 #define CONFIG_SYS_NS16550_CLK		(get_bus_freq(0)/2)

 #define CONFIG_SYS_BAUDRATE_TABLE	\
 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}

 #define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_CCSRBAR+0x11C500)
 #define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_CCSRBAR+0x11C600)
 #define CONFIG_SYS_NS16550_COM3	(CONFIG_SYS_CCSRBAR+0x11D500)
 #define CONFIG_SYS_NS16550_COM4	(CONFIG_SYS_CCSRBAR+0x11D600)

 /* I2C */
 #define CONFIG_SYS_I2C
 #define CONFIG_SYS_I2C_FSL
 #define CONFIG_I2C_MULTI_BUS
 #define CONFIG_I2C_CMD_TREE
 #define CONFIG_SYS_FSL_I2C_SPEED		400000	/* I2C speed and slave address */
 #define CONFIG_SYS_FSL_I2C_SLAVE		0x7F
 #define CONFIG_SYS_FSL_I2C_OFFSET		0x118000
 #define CONFIG_SYS_FSL_I2C2_SPEED		400000	/* I2C speed and slave address */
 #define CONFIG_SYS_FSL_I2C2_SLAVE		0x7F
 #define CONFIG_SYS_FSL_I2C2_OFFSET		0x118100
 #define CONFIG_SYS_FSL_I2C3_SPEED		400000	/* I2C speed and slave address */
 #define CONFIG_SYS_FSL_I2C3_SLAVE		0x7F
 #define CONFIG_SYS_FSL_I2C3_OFFSET		0x119000
 #define CONFIG_SYS_FSL_I2C4_SPEED		400000	/* I2C speed and slave address */
 #define CONFIG_SYS_FSL_I2C4_SLAVE		0x7F
 #define CONFIG_SYS_FSL_I2C4_OFFSET		0x119100

 #define CONFIG_ID_EEPROM
 #define CONFIG_SYS_I2C_EEPROM_NXID
 #define CONFIG_SYS_EEPROM_BUS_NUM	0
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1
 #define CONFIG_SYS_I2C_EEPROM_ADDR	0x57

 #define CONFIG_SYS_I2C_GENERIC_MAC
 #define CONFIG_SYS_I2C_MAC1_BUS 3
 #define CONFIG_SYS_I2C_MAC1_CHIP_ADDR 0x57
 #define CONFIG_SYS_I2C_MAC1_DATA_ADDR 0xf2
 #define CONFIG_SYS_I2C_MAC2_BUS 0
 #define CONFIG_SYS_I2C_MAC2_CHIP_ADDR 0x50
 #define CONFIG_SYS_I2C_MAC2_DATA_ADDR 0xfa

 #define CONFIG_RTC_MCP79411		1
 #define CONFIG_SYS_RTC_BUS_NUM		3
 #define CONFIG_SYS_I2C_RTC_ADDR		0x6f

 /*
  * eSPI - Enhanced SPI
  */

 /*
  * General PCI
  * Memory space is mapped 1-1, but I/O space must start from 0.
  */

 /* controller 1, direct to uli, tgtid 3, Base address 20000 */
 #define CONFIG_SYS_PCIE1_MEM_VIRT	0x80000000
 #ifdef CONFIG_PHYS_64BIT
 #define CONFIG_SYS_PCIE1_MEM_BUS	0xe0000000
 #define CONFIG_SYS_PCIE1_MEM_PHYS	0xc00000000ull
 #else
 #define CONFIG_SYS_PCIE1_MEM_BUS	0x80000000
 #define CONFIG_SYS_PCIE1_MEM_PHYS	0x80000000
 #endif
 #define CONFIG_SYS_PCIE1_MEM_SIZE	0x20000000	/* 512M */
 #define CONFIG_SYS_PCIE1_IO_VIRT	0xf8000000
 #define CONFIG_SYS_PCIE1_IO_BUS		0x00000000
 #ifdef CONFIG_PHYS_64BIT
 #define CONFIG_SYS_PCIE1_IO_PHYS	0xff8000000ull
 #else
 #define CONFIG_SYS_PCIE1_IO_PHYS	0xf8000000
 #endif
 #define CONFIG_SYS_PCIE1_IO_SIZE	0x00010000	/* 64k */

 /* controller 2, Slot 2, tgtid 2, Base address 201000 */
 #define CONFIG_SYS_PCIE2_MEM_VIRT	0xa0000000
 #ifdef CONFIG_PHYS_64BIT
 #define CONFIG_SYS_PCIE2_MEM_BUS	0xe0000000
 #define CONFIG_SYS_PCIE2_MEM_PHYS	0xc20000000ull
 #else
 #define CONFIG_SYS_PCIE2_MEM_BUS	0xa0000000
 #define CONFIG_SYS_PCIE2_MEM_PHYS	0xa0000000
 #endif
 #define CONFIG_SYS_PCIE2_MEM_SIZE	0x20000000	/* 512M */
 #define CONFIG_SYS_PCIE2_IO_VIRT	0xf8010000
 #define CONFIG_SYS_PCIE2_IO_BUS		0x00000000
 #ifdef CONFIG_PHYS_64BIT
 #define CONFIG_SYS_PCIE2_IO_PHYS	0xff8010000ull
 #else
 #define CONFIG_SYS_PCIE2_IO_PHYS	0xf8010000
 #endif
 #define CONFIG_SYS_PCIE2_IO_SIZE	0x00010000	/* 64k */

 /* controller 3, Slot 1, tgtid 1, Base address 202000 */
 #define CONFIG_SYS_PCIE3_MEM_VIRT	0xc0000000
 #ifdef CONFIG_PHYS_64BIT
 #define CONFIG_SYS_PCIE3_MEM_BUS	0xe0000000
 #define CONFIG_SYS_PCIE3_MEM_PHYS	0xc40000000ull
 #else
 #define CONFIG_SYS_PCIE3_MEM_BUS	0xc0000000
 #define CONFIG_SYS_PCIE3_MEM_PHYS	0xc0000000
 #endif
 #define CONFIG_SYS_PCIE3_MEM_SIZE	0x20000000	/* 512M */
 #define CONFIG_SYS_PCIE3_IO_VIRT	0xf8020000
 #define CONFIG_SYS_PCIE3_IO_BUS		0x00000000
 #ifdef CONFIG_PHYS_64BIT
 #define CONFIG_SYS_PCIE3_IO_PHYS	0xff8020000ull
 #else
 #define CONFIG_SYS_PCIE3_IO_PHYS	0xf8020000
 #endif
 #define CONFIG_SYS_PCIE3_IO_SIZE	0x00010000	/* 64k */

 /* controller 4, Base address 203000 */
 #define CONFIG_SYS_PCIE4_MEM_BUS	0xe0000000
 #define CONFIG_SYS_PCIE4_MEM_PHYS	0xc60000000ull
 #define CONFIG_SYS_PCIE4_MEM_SIZE	0x20000000	/* 512M */
 #define CONFIG_SYS_PCIE4_IO_BUS		0x00000000
 #define CONFIG_SYS_PCIE4_IO_PHYS	0xff8030000ull
 #define CONFIG_SYS_PCIE4_IO_SIZE	0x00010000	/* 64k */

 /* Qman/Bman */
 #define CONFIG_SYS_BMAN_NUM_PORTALS	10
 #define CONFIG_SYS_BMAN_MEM_BASE	0xf4000000
 #ifdef CONFIG_PHYS_64BIT
 #define CONFIG_SYS_BMAN_MEM_PHYS	0xff4000000ull
 #else
 #define CONFIG_SYS_BMAN_MEM_PHYS	CONFIG_SYS_BMAN_MEM_BASE
 #endif
 #define CONFIG_SYS_BMAN_MEM_SIZE	0x00200000
 #define CONFIG_SYS_BMAN_SP_CENA_SIZE    0x4000
 #define CONFIG_SYS_BMAN_SP_CINH_SIZE    0x1000
 #define CONFIG_SYS_BMAN_CENA_BASE       CONFIG_SYS_BMAN_MEM_BASE
 #define CONFIG_SYS_BMAN_CENA_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
 #define CONFIG_SYS_BMAN_CINH_BASE       (CONFIG_SYS_BMAN_MEM_BASE + \
 					 CONFIG_SYS_BMAN_CENA_SIZE)
 #define CONFIG_SYS_BMAN_CINH_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
 #define CONFIG_SYS_BMAN_SWP_ISDR_REG   0xE08
 #define CONFIG_SYS_QMAN_NUM_PORTALS	10
 #define CONFIG_SYS_QMAN_MEM_BASE	0xf4200000
 #ifdef CONFIG_PHYS_64BIT
 #define CONFIG_SYS_QMAN_MEM_PHYS	0xff4200000ull
 #else
 #define CONFIG_SYS_QMAN_MEM_PHYS	CONFIG_SYS_QMAN_MEM_BASE
 #endif
 #define CONFIG_SYS_QMAN_MEM_SIZE	0x00200000
 #define CONFIG_SYS_QMAN_SP_CENA_SIZE    0x4000
 #define CONFIG_SYS_QMAN_SP_CINH_SIZE    0x1000
 #define CONFIG_SYS_QMAN_CENA_BASE       CONFIG_SYS_QMAN_MEM_BASE
 #define CONFIG_SYS_QMAN_CENA_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
 #define CONFIG_SYS_QMAN_CINH_BASE       (CONFIG_SYS_QMAN_MEM_BASE + \
 					  CONFIG_SYS_QMAN_CENA_SIZE)
 #define CONFIG_SYS_QMAN_CINH_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
 #define CONFIG_SYS_QMAN_SWP_ISDR_REG   0xE08

 #define CONFIG_SYS_DPAA_FMAN
 /* Default address of microcode for the Linux Fman driver */
 /*
  * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
  * about 825KB (1650 blocks), Env is stored after the image, and the env size is
  * 0x2000 (16 blocks), 8 + 1650 + 16 = 1674, enlarge it to 1680.
  */
 #define CONFIG_SYS_QE_FMAN_FW_IN_MMC
 #define CONFIG_SYS_FMAN_FW_ADDR	(512 * 1680)

 #define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
 #define CONFIG_SYS_FDT_PAD		(0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)

 #ifdef CONFIG_SYS_DPAA_FMAN
 #define CONFIG_FMAN_ENET
 #endif

 #ifdef CONFIG_PCI
 #define CONFIG_PCI_INDIRECT_BRIDGE

 #define CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */
 #endif	/* CONFIG_PCI */

 /* SATA */
 #ifdef CONFIG_FSL_SATA_V2
 #define CONFIG_SYS_SATA_MAX_DEVICE	2
 #define CONFIG_SATA1
 #define CONFIG_SYS_SATA1		CONFIG_SYS_MPC85xx_SATA1_ADDR
 #define CONFIG_SYS_SATA1_FLAGS		FLAGS_DMA
 #define CONFIG_SATA2
 #define CONFIG_SYS_SATA2		CONFIG_SYS_MPC85xx_SATA2_ADDR
 #define CONFIG_SYS_SATA2_FLAGS		FLAGS_DMA

 #define CONFIG_LBA48
 #endif

 #ifdef CONFIG_FMAN_ENET
 #define CONFIG_SYS_TBIPA_VALUE	8
 #define CONFIG_MII		/* MII PHY management */
 #define CONFIG_ETHPRIME		"FM1@DTSEC4"
 #endif

 /*
  * Environment
  */
 #define CONFIG_LOADS_ECHO		/* echo on for serial download */
 #define CONFIG_SYS_LOADS_BAUD_CHANGE	/* allow baudrate change */

 /*
  * USB
  */
 #define CONFIG_HAS_FSL_DR_USB
 #define CONFIG_HAS_FSL_MPH_USB

 #if defined(CONFIG_HAS_FSL_DR_USB) || defined(CONFIG_HAS_FSL_MPH_USB)
 #define CONFIG_USB_EHCI_FSL
 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 #define CONFIG_EHCI_IS_TDI
  /* _VIA_CONTROL_EP  */
 #endif

 #ifdef CONFIG_MMC
 #define CONFIG_FSL_ESDHC
 #define CONFIG_SYS_FSL_ESDHC_ADDR       CONFIG_SYS_MPC85xx_ESDHC_ADDR
 #define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT
 #endif

 /*
  * Miscellaneous configurable options
  */
 #define CONFIG_SYS_LONGHELP			/* undef to save memory	*/
 #define CONFIG_CMDLINE_EDITING			/* Command-line editing */
 #define CONFIG_AUTO_COMPLETE			/* add autocompletion support */
 #define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */

 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 64 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
 #define CONFIG_SYS_BOOTMAPSZ	(64 << 20)	/* Initial Memory map for Linux*/
 #define CONFIG_SYS_BOOTM_LEN	(64 << 20)	/* Increase max gunzip size */

 #ifdef CONFIG_CMD_KGDB
 #define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
 #endif

 /*
  * Environment Configuration
  */
 #define CONFIG_ROOTPATH		"/opt/nfsroot"
 #define CONFIG_BOOTFILE		"uImage"
 #define CONFIG_UBOOTPATH	u-boot.bin	/* U-Boot image on TFTP server */

 /* default location for tftp and bootm */
 #define CONFIG_LOADADDR		1000000

 #define __USB_PHY_TYPE	utmi

 #define	CONFIG_EXTRA_ENV_SETTINGS \
 "hwconfig=fsl_ddr:ctlr_intlv=cacheline,"		\
 "bank_intlv=cs0_cs1;"					\
 "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) ";"\
 "usb2:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
 "netdev=eth0\0"						\
 "uboot=" __stringify(CONFIG_UBOOTPATH) "\0"			\
 "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0"			\
 "consoledev=ttyS0\0"					\
 "ramdiskaddr=2000000\0"					\
 "fdtaddr=1e00000\0"					\
 "bdev=sda3\0"

 #define CONFIG_HDBOOT					\
 "setenv bootargs root=/dev/$bdev rw "		\
 "console=$consoledev,$baudrate $othbootargs;"	\
 "tftp $loadaddr $bootfile;"			\
 "tftp $fdtaddr $fdtfile;"			\
 "bootm $loadaddr - $fdtaddr"

 #define CONFIG_NFSBOOTCOMMAND			\
 "setenv bootargs root=/dev/nfs rw "	\
 "nfsroot=$serverip:$rootpath "		\
 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
 "console=$consoledev,$baudrate $othbootargs;"	\
 "tftp $loadaddr $bootfile;"		\
 "tftp $fdtaddr $fdtfile;"		\
 "bootm $loadaddr - $fdtaddr"

 #define CONFIG_RAMBOOTCOMMAND				\
 "setenv bootargs root=/dev/ram rw "		\
 "console=$consoledev,$baudrate $othbootargs;"	\
 "tftp $ramdiskaddr $ramdiskfile;"		\
 "tftp $loadaddr $bootfile;"			\
 "tftp $fdtaddr $fdtfile;"			\
 "bootm $loadaddr $ramdiskaddr $fdtaddr"

 #define CONFIG_BOOTCOMMAND		CONFIG_HDBOOT

 #include <asm/fsl_secure_boot.h>

 #ifdef CONFIG_SECURE_BOOT
 #endif

 #endif	/* __CONFIG_H */
	/*
	* Based on corenet_ds.h
	*
	* SPDX-License-Identifier: GPL-2.0+
	*/

	#ifndef __CONFIG_H
	#define __CONFIG_H

	#if !defined(CONFIG_ARCH_P5020) && !defined(CONFIG_ARCH_P5040)
	#error Must call Cyrus CONFIG with a specific CPU enabled.
	#endif

	#define CONFIG_SDCARD
	#define CONFIG_FSL_SATA_V2
	#define CONFIG_PCIE3
	#define CONFIG_PCIE4
	#ifdef CONFIG_ARCH_P5020
	#define CONFIG_SYS_FSL_RAID_ENGINE
	#define CONFIG_SYS_DPAA_RMAN
	#endif
	#define CONFIG_SYS_DPAA_PME

	/*
	* Corenet DS style board configuration file
	*/
	#define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE
	#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
	#define CONFIG_SYS_FSL_PBL_PBI board/varisys/cyrus/pbi.cfg
	#if defined(CONFIG_ARCH_P5020)
	#define CONFIG_SYS_CLK_FREQ 133000000
	#define CONFIG_SYS_FSL_PBL_RCW board/varisys/cyrus/rcw_p5020_v2.cfg
	#elif defined(CONFIG_ARCH_P5040)
	#define CONFIG_SYS_CLK_FREQ 100000000
	#define CONFIG_SYS_FSL_PBL_RCW board/varisys/cyrus/rcw_p5040.cfg
	#endif

	/* High Level Configuration Options */
	#define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */
	#define CONFIG_MP /* support multiple processors */

	#define CONFIG_SYS_MMC_MAX_DEVICE 1

	#ifndef CONFIG_SYS_TEXT_BASE
	#define CONFIG_SYS_TEXT_BASE 0xeff40000
	#endif

	#define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */
	#define CONFIG_SYS_NUM_CPC CONFIG_SYS_NUM_DDR_CTLRS
	#define CONFIG_PCIE1 /* PCIE controller 1 */
	#define CONFIG_PCIE2 /* PCIE controller 2 */
	#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */
	#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */

	#define CONFIG_ENV_OVERWRITE

	#if defined(CONFIG_SDCARD)
	#define CONFIG_SYS_EXTRA_ENV_RELOC
	#define CONFIG_FSL_FIXED_MMC_LOCATION
	#define CONFIG_SYS_MMC_ENV_DEV 0
	#define CONFIG_ENV_SIZE 0x2000
	#define CONFIG_ENV_OFFSET (512 * 1658)
	#endif

	/*
	* These can be toggled for performance analysis, otherwise use default.
	*/
	#define CONFIG_SYS_CACHE_STASHING
	#define CONFIG_BACKSIDE_L2_CACHE
	#define CONFIG_SYS_INIT_L2CSR0 L2CSR0_L2E
	#define CONFIG_BTB /* toggle branch predition */
	#define CONFIG_DDR_ECC
	#ifdef CONFIG_DDR_ECC
	#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
	#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
	#endif

	#define CONFIG_ENABLE_36BIT_PHYS

	#ifdef CONFIG_PHYS_64BIT
	#define CONFIG_ADDR_MAP
	#define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */
	#endif

	/* test POST memory test */
	#undef CONFIG_POST
	#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */
	#define CONFIG_SYS_MEMTEST_END 0x00400000
	#define CONFIG_SYS_ALT_MEMTEST

	/*
	* Config the L3 Cache as L3 SRAM
	*/
	#define CONFIG_SYS_INIT_L3_ADDR CONFIG_RAMBOOT_TEXT_BASE
	#ifdef CONFIG_PHYS_64BIT
	#define CONFIG_SYS_INIT_L3_ADDR_PHYS (0xf00000000ull \| CONFIG_RAMBOOT_TEXT_BASE)
	#else
	#define CONFIG_SYS_INIT_L3_ADDR_PHYS CONFIG_SYS_INIT_L3_ADDR
	#endif
	#define CONFIG_SYS_L3_SIZE (1024 << 10)
	#define CONFIG_SYS_INIT_L3_END (CONFIG_SYS_INIT_L3_ADDR + CONFIG_SYS_L3_SIZE)

	#ifdef CONFIG_PHYS_64BIT
	#define CONFIG_SYS_DCSRBAR 0xf0000000
	#define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull
	#endif

	/*
	* DDR Setup
	*/
	#define CONFIG_VERY_BIG_RAM
	#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
	#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE

	#define CONFIG_DIMM_SLOTS_PER_CTLR 1
	#define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR)

	#define CONFIG_DDR_SPD

	#define CONFIG_SYS_SPD_BUS_NUM 1
	#define SPD_EEPROM_ADDRESS1 0x51
	#define SPD_EEPROM_ADDRESS2 0x52
	#define CONFIG_SYS_SDRAM_SIZE 4096 /* for fixed parameter use */

	/*
	* Local Bus Definitions
	*/

	#define CONFIG_SYS_LBC0_BASE 0xe0000000 /* Start of LBC Registers */
	#ifdef CONFIG_PHYS_64BIT
	#define CONFIG_SYS_LBC0_BASE_PHYS 0xfe0000000ull
	#else
	#define CONFIG_SYS_LBC0_BASE_PHYS CONFIG_SYS_LBC0_BASE
	#endif

	#define CONFIG_SYS_LBC1_BASE 0xe1000000 /* Start of LBC Registers */
	#ifdef CONFIG_PHYS_64BIT
	#define CONFIG_SYS_LBC1_BASE_PHYS 0xfe1000000ull
	#else
	#define CONFIG_SYS_LBC1_BASE_PHYS CONFIG_SYS_LBC1_BASE
	#endif

	/* Set the local bus clock 1/16 of platform clock */
	#define CONFIG_SYS_LBC_LCRR (LCRR_CLKDIV_16 \| LCRR_EADC_1)

	#define CONFIG_SYS_BR0_PRELIM \
	(BR_PHYS_ADDR(CONFIG_SYS_LBC0_BASE_PHYS) \| BR_PS_16 \| BR_V)
	#define CONFIG_SYS_BR1_PRELIM \
	(BR_PHYS_ADDR(CONFIG_SYS_LBC1_BASE_PHYS) \| BR_PS_16 \| BR_V)

	#define CONFIG_SYS_OR0_PRELIM 0xfff00010
	#define CONFIG_SYS_OR1_PRELIM 0xfff00010

	#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */

	#if defined(CONFIG_RAMBOOT_PBL)
	#define CONFIG_SYS_RAMBOOT
	#endif

	#define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */
	#define CONFIG_MISC_INIT_R

	#define CONFIG_HWCONFIG

	/* define to use L1 as initial stack */
	#define CONFIG_L1_INIT_RAM
	#define CONFIG_SYS_INIT_RAM_LOCK
	#define CONFIG_SYS_INIT_RAM_ADDR 0xfdd00000 /* Initial L1 address */
	#ifdef CONFIG_PHYS_64BIT
	#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf
	#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR
	/* The assembler doesn't like typecast */
	#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
	((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) \| \
	CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
	#else
	#define CONFIG_SYS_INIT_RAM_ADDR_PHYS CONFIG_SYS_INIT_RAM_ADDR /* Initial L1 address */
	#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0
	#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS
	#endif
	#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 /* Size of used area in RAM */

	#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
	#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET

	#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
	#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */

	/* Serial Port - controlled on board with jumper J8
	* open - index 2
	* shorted - index 1
	*/
	#define CONFIG_CONS_INDEX 1
	#define CONFIG_SYS_NS16550_SERIAL
	#define CONFIG_SYS_NS16550_REG_SIZE 1
	#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2)

	#define CONFIG_SYS_BAUDRATE_TABLE \
	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}

	#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500)
	#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600)
	#define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500)
	#define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600)

	/* I2C */
	#define CONFIG_SYS_I2C
	#define CONFIG_SYS_I2C_FSL
	#define CONFIG_I2C_MULTI_BUS
	#define CONFIG_I2C_CMD_TREE
	#define CONFIG_SYS_FSL_I2C_SPEED 400000 /* I2C speed and slave address */
	#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
	#define CONFIG_SYS_FSL_I2C_OFFSET 0x118000
	#define CONFIG_SYS_FSL_I2C2_SPEED 400000 /* I2C speed and slave address */
	#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
	#define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100
	#define CONFIG_SYS_FSL_I2C3_SPEED 400000 /* I2C speed and slave address */
	#define CONFIG_SYS_FSL_I2C3_SLAVE 0x7F
	#define CONFIG_SYS_FSL_I2C3_OFFSET 0x119000
	#define CONFIG_SYS_FSL_I2C4_SPEED 400000 /* I2C speed and slave address */
	#define CONFIG_SYS_FSL_I2C4_SLAVE 0x7F
	#define CONFIG_SYS_FSL_I2C4_OFFSET 0x119100

	#define CONFIG_ID_EEPROM
	#define CONFIG_SYS_I2C_EEPROM_NXID
	#define CONFIG_SYS_EEPROM_BUS_NUM 0
	#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
	#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57

	#define CONFIG_SYS_I2C_GENERIC_MAC
	#define CONFIG_SYS_I2C_MAC1_BUS 3
	#define CONFIG_SYS_I2C_MAC1_CHIP_ADDR 0x57
	#define CONFIG_SYS_I2C_MAC1_DATA_ADDR 0xf2
	#define CONFIG_SYS_I2C_MAC2_BUS 0
	#define CONFIG_SYS_I2C_MAC2_CHIP_ADDR 0x50
	#define CONFIG_SYS_I2C_MAC2_DATA_ADDR 0xfa

	#define CONFIG_RTC_MCP79411 1
	#define CONFIG_SYS_RTC_BUS_NUM 3
	#define CONFIG_SYS_I2C_RTC_ADDR 0x6f

	/*
	* eSPI - Enhanced SPI
	*/

	/*
	* General PCI
	* Memory space is mapped 1-1, but I/O space must start from 0.
	*/

	/* controller 1, direct to uli, tgtid 3, Base address 20000 */
	#define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000
	#ifdef CONFIG_PHYS_64BIT
	#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000
	#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull
	#else
	#define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000
	#define CONFIG_SYS_PCIE1_MEM_PHYS 0x80000000
	#endif
	#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
	#define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000
	#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
	#ifdef CONFIG_PHYS_64BIT
	#define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull
	#else
	#define CONFIG_SYS_PCIE1_IO_PHYS 0xf8000000
	#endif
	#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */

	/* controller 2, Slot 2, tgtid 2, Base address 201000 */
	#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000
	#ifdef CONFIG_PHYS_64BIT
	#define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000
	#define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull
	#else
	#define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000
	#define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000
	#endif
	#define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */
	#define CONFIG_SYS_PCIE2_IO_VIRT 0xf8010000
	#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000
	#ifdef CONFIG_PHYS_64BIT
	#define CONFIG_SYS_PCIE2_IO_PHYS 0xff8010000ull
	#else
	#define CONFIG_SYS_PCIE2_IO_PHYS 0xf8010000
	#endif
	#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */

	/* controller 3, Slot 1, tgtid 1, Base address 202000 */
	#define CONFIG_SYS_PCIE3_MEM_VIRT 0xc0000000
	#ifdef CONFIG_PHYS_64BIT
	#define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000
	#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc40000000ull
	#else
	#define CONFIG_SYS_PCIE3_MEM_BUS 0xc0000000
	#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc0000000
	#endif
	#define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */
	#define CONFIG_SYS_PCIE3_IO_VIRT 0xf8020000
	#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000
	#ifdef CONFIG_PHYS_64BIT
	#define CONFIG_SYS_PCIE3_IO_PHYS 0xff8020000ull
	#else
	#define CONFIG_SYS_PCIE3_IO_PHYS 0xf8020000
	#endif
	#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */

	/* controller 4, Base address 203000 */
	#define CONFIG_SYS_PCIE4_MEM_BUS 0xe0000000
	#define CONFIG_SYS_PCIE4_MEM_PHYS 0xc60000000ull
	#define CONFIG_SYS_PCIE4_MEM_SIZE 0x20000000 /* 512M */
	#define CONFIG_SYS_PCIE4_IO_BUS 0x00000000
	#define CONFIG_SYS_PCIE4_IO_PHYS 0xff8030000ull
	#define CONFIG_SYS_PCIE4_IO_SIZE 0x00010000 /* 64k */

	/* Qman/Bman */
	#define CONFIG_SYS_BMAN_NUM_PORTALS 10
	#define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000
	#ifdef CONFIG_PHYS_64BIT
	#define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull
	#else
	#define CONFIG_SYS_BMAN_MEM_PHYS CONFIG_SYS_BMAN_MEM_BASE
	#endif
	#define CONFIG_SYS_BMAN_MEM_SIZE 0x00200000
	#define CONFIG_SYS_BMAN_SP_CENA_SIZE 0x4000
	#define CONFIG_SYS_BMAN_SP_CINH_SIZE 0x1000
	#define CONFIG_SYS_BMAN_CENA_BASE CONFIG_SYS_BMAN_MEM_BASE
	#define CONFIG_SYS_BMAN_CENA_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
	#define CONFIG_SYS_BMAN_CINH_BASE (CONFIG_SYS_BMAN_MEM_BASE + \
	CONFIG_SYS_BMAN_CENA_SIZE)
	#define CONFIG_SYS_BMAN_CINH_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
	#define CONFIG_SYS_BMAN_SWP_ISDR_REG 0xE08
	#define CONFIG_SYS_QMAN_NUM_PORTALS 10
	#define CONFIG_SYS_QMAN_MEM_BASE 0xf4200000
	#ifdef CONFIG_PHYS_64BIT
	#define CONFIG_SYS_QMAN_MEM_PHYS 0xff4200000ull
	#else
	#define CONFIG_SYS_QMAN_MEM_PHYS CONFIG_SYS_QMAN_MEM_BASE
	#endif
	#define CONFIG_SYS_QMAN_MEM_SIZE 0x00200000
	#define CONFIG_SYS_QMAN_SP_CENA_SIZE 0x4000
	#define CONFIG_SYS_QMAN_SP_CINH_SIZE 0x1000
	#define CONFIG_SYS_QMAN_CENA_BASE CONFIG_SYS_QMAN_MEM_BASE
	#define CONFIG_SYS_QMAN_CENA_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
	#define CONFIG_SYS_QMAN_CINH_BASE (CONFIG_SYS_QMAN_MEM_BASE + \
	CONFIG_SYS_QMAN_CENA_SIZE)
	#define CONFIG_SYS_QMAN_CINH_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
	#define CONFIG_SYS_QMAN_SWP_ISDR_REG 0xE08

	#define CONFIG_SYS_DPAA_FMAN
	/* Default address of microcode for the Linux Fman driver */
	/*
	* PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
	* about 825KB (1650 blocks), Env is stored after the image, and the env size is
	* 0x2000 (16 blocks), 8 + 1650 + 16 = 1674, enlarge it to 1680.
	*/
	#define CONFIG_SYS_QE_FMAN_FW_IN_MMC
	#define CONFIG_SYS_FMAN_FW_ADDR (512 * 1680)

	#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000
	#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)

	#ifdef CONFIG_SYS_DPAA_FMAN
	#define CONFIG_FMAN_ENET
	#endif

	#ifdef CONFIG_PCI
	#define CONFIG_PCI_INDIRECT_BRIDGE

	#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
	#endif /* CONFIG_PCI */

	/* SATA */
	#ifdef CONFIG_FSL_SATA_V2
	#define CONFIG_SYS_SATA_MAX_DEVICE 2
	#define CONFIG_SATA1
	#define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR
	#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA
	#define CONFIG_SATA2
	#define CONFIG_SYS_SATA2 CONFIG_SYS_MPC85xx_SATA2_ADDR
	#define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA

	#define CONFIG_LBA48
	#endif

	#ifdef CONFIG_FMAN_ENET
	#define CONFIG_SYS_TBIPA_VALUE 8
	#define CONFIG_MII /* MII PHY management */
	#define CONFIG_ETHPRIME "FM1@DTSEC4"
	#endif

	/*
	* Environment
	*/
	#define CONFIG_LOADS_ECHO /* echo on for serial download */
	#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */

	/*
	* USB
	*/
	#define CONFIG_HAS_FSL_DR_USB
	#define CONFIG_HAS_FSL_MPH_USB

	#if defined(CONFIG_HAS_FSL_DR_USB) \|\| defined(CONFIG_HAS_FSL_MPH_USB)
	#define CONFIG_USB_EHCI_FSL
	#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
	#define CONFIG_EHCI_IS_TDI
	/* _VIA_CONTROL_EP */
	#endif

	#ifdef CONFIG_MMC
	#define CONFIG_FSL_ESDHC
	#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR
	#define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT
	#endif

	/*
	* Miscellaneous configurable options
	*/
	#define CONFIG_SYS_LONGHELP /* undef to save memory */
	#define CONFIG_CMDLINE_EDITING /* Command-line editing */
	#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
	#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */

	/*
	* For booting Linux, the board info and command line data
	* have to be in the first 64 MB of memory, since this is
	* the maximum mapped by the Linux kernel during initialization.
	*/
	#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux*/
	#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */

	#ifdef CONFIG_CMD_KGDB
	#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
	#endif

	/*
	* Environment Configuration
	*/
	#define CONFIG_ROOTPATH "/opt/nfsroot"
	#define CONFIG_BOOTFILE "uImage"
	#define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */

	/* default location for tftp and bootm */
	#define CONFIG_LOADADDR 1000000

	#define __USB_PHY_TYPE utmi

	#define CONFIG_EXTRA_ENV_SETTINGS \
	"hwconfig=fsl_ddr:ctlr_intlv=cacheline," \
	"bank_intlv=cs0_cs1;" \
	"usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) ";"\
	"usb2:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
	"netdev=eth0\0" \
	"uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \
	"ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \
	"consoledev=ttyS0\0" \
	"ramdiskaddr=2000000\0" \
	"fdtaddr=1e00000\0" \
	"bdev=sda3\0"

	#define CONFIG_HDBOOT \
	"setenv bootargs root=/dev/$bdev rw " \
	"console=$consoledev,$baudrate $othbootargs;" \
	"tftp $loadaddr $bootfile;" \
	"tftp $fdtaddr $fdtfile;" \
	"bootm $loadaddr - $fdtaddr"

	#define CONFIG_NFSBOOTCOMMAND \
	"setenv bootargs root=/dev/nfs rw " \
	"nfsroot=$serverip:$rootpath " \
	"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
	"console=$consoledev,$baudrate $othbootargs;" \
	"tftp $loadaddr $bootfile;" \
	"tftp $fdtaddr $fdtfile;" \
	"bootm $loadaddr - $fdtaddr"

	#define CONFIG_RAMBOOTCOMMAND \
	"setenv bootargs root=/dev/ram rw " \
	"console=$consoledev,$baudrate $othbootargs;" \
	"tftp $ramdiskaddr $ramdiskfile;" \
	"tftp $loadaddr $bootfile;" \
	"tftp $fdtaddr $fdtfile;" \
	"bootm $loadaddr $ramdiskaddr $fdtaddr"

	#define CONFIG_BOOTCOMMAND CONFIG_HDBOOT

	#include <asm/fsl_secure_boot.h>

	#ifdef CONFIG_SECURE_BOOT
	#endif

	#endif /* __CONFIG_H */