include/configs/MPC8610HPCD.h - github/trini/u-boot - Gitiles

 /*
  * Copyright 2007-2011 Freescale Semiconductor, Inc.
  *
  * SPDX-License-Identifier:	GPL-2.0
  */

 /*
  * MPC8610HPCD board configuration file
  */

 #ifndef __CONFIG_H
 #define __CONFIG_H

 /* High Level Configuration Options */
 #define CONFIG_LINUX_RESET_VEC	0x100	/* Reset vector used by Linux */

 /* video */
 #define CONFIG_FSL_DIU_FB

 #ifdef CONFIG_FSL_DIU_FB
 #define CONFIG_SYS_DIU_ADDR	(CONFIG_SYS_CCSRBAR + 0x2c000)
 #define CONFIG_VIDEO_LOGO
 #define CONFIG_VIDEO_BMP_LOGO
 #endif

 #ifdef RUN_DIAG
 #define CONFIG_SYS_DIAG_ADDR		0xff800000
 #endif

 /*
  * virtual address to be used for temporary mappings.  There
  * should be 128k free at this VA.
  */
 #define CONFIG_SYS_SCRATCH_VA	0xc0000000

 #define CONFIG_PCI1		1	/* PCI controller 1 */
 #define CONFIG_PCIE1		1	/* PCIe 1 connected to ULI bridge */
 #define CONFIG_PCIE2		1	/* PCIe 2 connected to slot */
 #define CONFIG_FSL_PCI_INIT	1	/* Use common FSL init code */
 #define CONFIG_PCI_INDIRECT_BRIDGE 1	/* indirect PCI bridge support */
 #define CONFIG_SYS_PCI_64BIT	1	/* enable 64-bit PCI resources */

 #define CONFIG_ENV_OVERWRITE
 #define CONFIG_INTERRUPTS		/* enable pci, srio, ddr interrupts */

 #define CONFIG_BAT_RW		1	/* Use common BAT rw code */
 #define CONFIG_HIGH_BATS	1	/* High BATs supported & enabled */
 #define CONFIG_ALTIVEC		1

 /*
  * L2CR setup -- make sure this is right for your board!
  */
 #define CONFIG_SYS_L2
 #define L2_INIT		0
 #define L2_ENABLE	(L2CR_L2E |0x00100000 )

 #ifndef CONFIG_SYS_CLK_FREQ
 #define CONFIG_SYS_CLK_FREQ	get_board_sys_clk(0)
 #endif

 #define CONFIG_MISC_INIT_R		1

 #define CONFIG_SYS_MEMTEST_START	0x00200000	/* memtest region */
 #define CONFIG_SYS_MEMTEST_END		0x00400000

 /*
  * Base addresses -- Note these are effective addresses where the
  * actual resources get mapped (not physical addresses)
  */
 #define CONFIG_SYS_CCSRBAR		0xe0000000	/* relocated CCSRBAR */
 #define CONFIG_SYS_IMMR		CONFIG_SYS_CCSRBAR	/* PQII uses CONFIG_SYS_IMMR */

 #define CONFIG_SYS_CCSRBAR_PHYS_LOW	CONFIG_SYS_CCSRBAR
 #define CONFIG_SYS_CCSRBAR_PHYS_HIGH	0x0
 #define CONFIG_SYS_CCSRBAR_PHYS		CONFIG_SYS_CCSRBAR_PHYS_LOW

 /* DDR Setup */
 #undef CONFIG_FSL_DDR_INTERACTIVE
 #define CONFIG_SPD_EEPROM		/* Use SPD for DDR */
 #define CONFIG_DDR_SPD

 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER	/* DDR controller or DMA? */
 #define CONFIG_MEM_INIT_VALUE	0xDeadBeef

 #define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000	/* DDR is system memory*/
 #define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
 #define CONFIG_SYS_MAX_DDR_BAT_SIZE	0x80000000	/* BAT mapping size */
 #define CONFIG_VERY_BIG_RAM

 #define CONFIG_DIMM_SLOTS_PER_CTLR	1
 #define CONFIG_CHIP_SELECTS_PER_CTRL	(2 * CONFIG_DIMM_SLOTS_PER_CTLR)

 #define SPD_EEPROM_ADDRESS	0x51	/* CTLR 0 DIMM 0 */

 /* These are used when DDR doesn't use SPD.  */
 #define CONFIG_SYS_SDRAM_SIZE	256		/* DDR is 256MB */

 #if 0 /* TODO */
 #define CONFIG_SYS_DDR_CS0_BNDS	0x0000000F
 #define CONFIG_SYS_DDR_CS0_CONFIG	0x80010202	/* Enable, no interleaving */
 #define CONFIG_SYS_DDR_TIMING_3	0x00000000
 #define CONFIG_SYS_DDR_TIMING_0	0x00260802
 #define CONFIG_SYS_DDR_TIMING_1	0x3935d322
 #define CONFIG_SYS_DDR_TIMING_2	0x14904cc8
 #define CONFIG_SYS_DDR_MODE_1		0x00480432
 #define CONFIG_SYS_DDR_MODE_2		0x00000000
 #define CONFIG_SYS_DDR_INTERVAL	0x06180100
 #define CONFIG_SYS_DDR_DATA_INIT	0xdeadbeef
 #define CONFIG_SYS_DDR_CLK_CTRL	0x03800000
 #define CONFIG_SYS_DDR_OCD_CTRL	0x00000000
 #define CONFIG_SYS_DDR_OCD_STATUS	0x00000000
 #define CONFIG_SYS_DDR_CONTROL		0xe3008000	/* Type = DDR2 */
 #define CONFIG_SYS_DDR_CONTROL2	0x04400010

 #define CONFIG_SYS_DDR_ERR_INT_EN	0x00000000
 #define CONFIG_SYS_DDR_ERR_DIS		0x00000000
 #define CONFIG_SYS_DDR_SBE		0x000f0000

 #endif

 #define CONFIG_ID_EEPROM
 #define CONFIG_SYS_I2C_EEPROM_NXID
 #define CONFIG_ID_EEPROM
 #define CONFIG_SYS_I2C_EEPROM_ADDR     0x57
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1

 #define CONFIG_SYS_FLASH_BASE		0xf0000000 /* start of FLASH 128M */
 #define CONFIG_SYS_FLASH_BASE2		0xf8000000

 #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2}

 #define CONFIG_SYS_BR0_PRELIM		0xf8001001 /* port size 16bit */
 #define CONFIG_SYS_OR0_PRELIM		0xf8006e65 /* 128MB NOR Flash*/

 #define CONFIG_SYS_BR1_PRELIM		0xf0001001 /* port size 16bit */
 #define CONFIG_SYS_OR1_PRELIM		0xf8006e65 /* 128MB Promjet */
 #if 0 /* TODO */
 #define CONFIG_SYS_BR2_PRELIM		0xf0000000
 #define CONFIG_SYS_OR2_PRELIM		0xf0000000 /* 256MB NAND Flash - bank 1 */
 #endif
 #define CONFIG_SYS_BR3_PRELIM		0xe8000801 /* port size 8bit */
 #define CONFIG_SYS_OR3_PRELIM		0xfff06ff7 /* 1MB PIXIS area*/

 #define CONFIG_FSL_PIXIS	1	/* use common PIXIS code */
 #define PIXIS_BASE	0xe8000000	/* PIXIS registers */
 #define PIXIS_ID		0x0	/* Board ID at offset 0 */
 #define PIXIS_VER		0x1	/* Board version at offset 1 */
 #define PIXIS_PVER		0x2	/* PIXIS FPGA version at offset 2 */
 #define PIXIS_RST		0x4	/* PIXIS Reset Control register */
 #define PIXIS_AUX		0x6	/* PIXIS Auxiliary register; Scratch */
 #define PIXIS_SPD		0x7	/* Register for SYSCLK speed */
 #define PIXIS_BRDCFG0		0x8	/* PIXIS Board Configuration Register0*/
 #define PIXIS_VCTL		0x10	/* VELA Control Register */
 #define PIXIS_VCFGEN0		0x12	/* VELA Config Enable 0 */
 #define PIXIS_VCFGEN1		0x13	/* VELA Config Enable 1 */
 #define PIXIS_VBOOT		0x16	/* VELA VBOOT Register */
 #define PIXIS_VSPEED0		0x17	/* VELA VSpeed 0 */
 #define PIXIS_VSPEED1		0x18	/* VELA VSpeed 1 */
 #define PIXIS_VCLKH		0x19	/* VELA VCLKH register */
 #define PIXIS_VCLKL		0x1A	/* VELA VCLKL register */
 #define CONFIG_SYS_PIXIS_VBOOT_MASK	0xC0    /* Reset altbank mask */

 #define CONFIG_SYS_MAX_FLASH_BANKS	2		/* number of banks */
 #define CONFIG_SYS_MAX_FLASH_SECT	1024		/* sectors per device */

 #undef	CONFIG_SYS_FLASH_CHECKSUM
 #define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
 #define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
 #define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor */
 #define CONFIG_SYS_MONITOR_BASE_EARLY   0xfff00000	/* early monitor loc */

 #define CONFIG_FLASH_CFI_DRIVER
 #define CONFIG_SYS_FLASH_CFI
 #define CONFIG_SYS_FLASH_EMPTY_INFO

 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
 #define CONFIG_SYS_RAMBOOT
 #else
 #undef	CONFIG_SYS_RAMBOOT
 #endif

 #if defined(CONFIG_SYS_RAMBOOT)
 #undef CONFIG_SPD_EEPROM
 #define CONFIG_SYS_SDRAM_SIZE	256
 #endif

 #undef CONFIG_CLOCKS_IN_MHZ

 #define CONFIG_SYS_INIT_RAM_LOCK	1
 #ifndef CONFIG_SYS_INIT_RAM_LOCK
 #define CONFIG_SYS_INIT_RAM_ADDR	0xe4010000	/* Initial RAM address */
 #else
 #define CONFIG_SYS_INIT_RAM_ADDR	0xe4000000	/* Initial RAM address */
 #endif
 #define CONFIG_SYS_INIT_RAM_SIZE	0x4000		/* Size of used area in RAM */

 #define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET

 #define CONFIG_SYS_MONITOR_LEN		(512 * 1024)	/* Reserve 512 KB for Mon */
 #define CONFIG_SYS_MALLOC_LEN		(6 * 1024 * 1024)	/* Reserved for malloc */

 /* Serial Port */
 #define CONFIG_CONS_INDEX	1
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE	1
 #define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)

 #define CONFIG_SYS_BAUDRATE_TABLE \
 	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}

 #define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_CCSRBAR+0x4500)
 #define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_CCSRBAR+0x4600)

 /* maximum size of the flat tree (8K) */
 #define OF_FLAT_TREE_MAX_SIZE	8192

 /*
  * I2C
  */
 #define CONFIG_SYS_I2C
 #define CONFIG_SYS_I2C_FSL
 #define CONFIG_SYS_FSL_I2C_SPEED	400000
 #define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
 #define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
 #define CONFIG_SYS_I2C_NOPROBES		{ {0, 0x69} }

 /*
  * General PCI
  * Addresses are mapped 1-1.
  */
 #define CONFIG_SYS_PCI1_MEM_BUS		0x80000000
 #define CONFIG_SYS_PCI1_MEM_PHYS	CONFIG_SYS_PCI1_MEM_BUS
 #define CONFIG_SYS_PCI1_MEM_VIRT	CONFIG_SYS_PCI1_MEM_BUS
 #define CONFIG_SYS_PCI1_MEM_SIZE	0x10000000	/* 256M */
 #define CONFIG_SYS_PCI1_IO_BUS	0x0000000
 #define CONFIG_SYS_PCI1_IO_PHYS	0xe1000000
 #define CONFIG_SYS_PCI1_IO_VIRT	0xe1000000
 #define CONFIG_SYS_PCI1_IO_SIZE	0x00100000	/* 1M */

 /* controller 1, Base address 0xa000 */
 #define CONFIG_SYS_PCIE1_NAME		"ULI"
 #define CONFIG_SYS_PCIE1_MEM_BUS	0xa0000000
 #define CONFIG_SYS_PCIE1_MEM_PHYS	CONFIG_SYS_PCIE1_MEM_BUS
 #define CONFIG_SYS_PCIE1_MEM_SIZE	0x10000000	/* 256M */
 #define CONFIG_SYS_PCIE1_IO_BUS		0x00000000
 #define CONFIG_SYS_PCIE1_IO_PHYS	0xe3000000
 #define CONFIG_SYS_PCIE1_IO_SIZE	0x00100000	/* 1M */

 /* controller 2, Base Address 0x9000 */
 #define CONFIG_SYS_PCIE2_NAME		"Slot 1"
 #define CONFIG_SYS_PCIE2_MEM_BUS	0x90000000
 #define CONFIG_SYS_PCIE2_MEM_PHYS	CONFIG_SYS_PCIE2_MEM_BUS
 #define CONFIG_SYS_PCIE2_MEM_SIZE	0x10000000	/* 256M */
 #define CONFIG_SYS_PCIE2_IO_BUS		0x00000000	/* reuse mem LAW */
 #define CONFIG_SYS_PCIE2_IO_PHYS	0xe2000000
 #define CONFIG_SYS_PCIE2_IO_SIZE	0x00100000	/* 1M */

 #if defined(CONFIG_PCI)

 #define CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */

 #define CONFIG_ULI526X
 #ifdef CONFIG_ULI526X
 #endif

 /************************************************************
  * USB support
  ************************************************************/
 #define CONFIG_PCI_OHCI		1
 #define CONFIG_USB_OHCI_NEW		1
 #define CONFIG_SYS_USB_OHCI_SLOT_NAME	"ohci_pci"
 #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15
 #define CONFIG_SYS_OHCI_SWAP_REG_ACCESS	1

 #if !defined(CONFIG_PCI_PNP)
 #define PCI_ENET0_IOADDR	0xe0000000
 #define PCI_ENET0_MEMADDR	0xe0000000
 #define PCI_IDSEL_NUMBER	0x0c	/* slot0->3(IDSEL)=12->15 */
 #endif

 #ifdef CONFIG_SCSI_AHCI
 #define CONFIG_SATA_ULI5288
 #define CONFIG_SYS_SCSI_MAX_SCSI_ID	4
 #define CONFIG_SYS_SCSI_MAX_LUN	1
 #define CONFIG_SYS_SCSI_MAX_DEVICE	(CONFIG_SYS_SCSI_MAX_SCSI_ID * CONFIG_SYS_SCSI_MAX_LUN)
 #define CONFIG_SYS_SCSI_MAXDEVICE	CONFIG_SYS_SCSI_MAX_DEVICE
 #endif

 #endif	/* CONFIG_PCI */

 /*
  * BAT0		2G	Cacheable, non-guarded
  * 0x0000_0000	2G	DDR
  */
 #define CONFIG_SYS_DBAT0L	(BATL_PP_RW)
 #define CONFIG_SYS_IBAT0L	(BATL_PP_RW)

 /*
  * BAT1		1G	Cache-inhibited, guarded
  * 0x8000_0000	256M	PCI-1 Memory
  * 0xa000_0000	256M	PCI-Express 1 Memory
  * 0x9000_0000	256M	PCI-Express 2 Memory
  */

 #define CONFIG_SYS_DBAT1L	(CONFIG_SYS_PCI1_MEM_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT \
 			| BATL_GUARDEDSTORAGE)
 #define CONFIG_SYS_DBAT1U	(CONFIG_SYS_PCI1_MEM_VIRT | BATU_BL_1G | BATU_VS | BATU_VP)
 #define CONFIG_SYS_IBAT1L	(CONFIG_SYS_PCI1_MEM_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT)
 #define CONFIG_SYS_IBAT1U	CONFIG_SYS_DBAT1U

 /*
  * BAT2		16M	Cache-inhibited, guarded
  * 0xe100_0000	1M	PCI-1 I/O
  */

 #define CONFIG_SYS_DBAT2L	(CONFIG_SYS_PCI1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT \
 			| BATL_GUARDEDSTORAGE)
 #define CONFIG_SYS_DBAT2U	(CONFIG_SYS_PCI1_IO_VIRT | BATU_BL_16M | BATU_VS | BATU_VP)
 #define CONFIG_SYS_IBAT2L	(CONFIG_SYS_PCI1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT)
 #define CONFIG_SYS_IBAT2U	CONFIG_SYS_DBAT2U

 /*
  * BAT3		4M	Cache-inhibited, guarded
  * 0xe000_0000	4M	CCSR
  */

 #define CONFIG_SYS_DBAT3L	(CONFIG_SYS_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT \
 			| BATL_GUARDEDSTORAGE)
 #define CONFIG_SYS_DBAT3U	(CONFIG_SYS_CCSRBAR | BATU_BL_1M | BATU_VS | BATU_VP)
 #define CONFIG_SYS_IBAT3L	(CONFIG_SYS_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT)
 #define CONFIG_SYS_IBAT3U	CONFIG_SYS_DBAT3U

 #if (CONFIG_SYS_CCSRBAR_DEFAULT != CONFIG_SYS_CCSRBAR)
 #define CONFIG_SYS_CCSR_DEFAULT_DBATL (CONFIG_SYS_CCSRBAR_DEFAULT \
 				       | BATL_PP_RW | BATL_CACHEINHIBIT \
 				       | BATL_GUARDEDSTORAGE)
 #define CONFIG_SYS_CCSR_DEFAULT_DBATU (CONFIG_SYS_CCSRBAR_DEFAULT \
 				       | BATU_BL_1M | BATU_VS | BATU_VP)
 #define CONFIG_SYS_CCSR_DEFAULT_IBATL (CONFIG_SYS_CCSRBAR_DEFAULT \
 				       | BATL_PP_RW | BATL_CACHEINHIBIT)
 #define CONFIG_SYS_CCSR_DEFAULT_IBATU CONFIG_SYS_CCSR_DEFAULT_DBATU
 #endif

 /*
  * BAT4		32M	Cache-inhibited, guarded
  * 0xe200_0000	1M	PCI-Express 2 I/O
  * 0xe300_0000	1M	PCI-Express 1 I/O
  */

 #define CONFIG_SYS_DBAT4L	(CONFIG_SYS_PCIE2_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT \
 			| BATL_GUARDEDSTORAGE)
 #define CONFIG_SYS_DBAT4U	(CONFIG_SYS_PCIE2_IO_PHYS | BATU_BL_32M | BATU_VS | BATU_VP)
 #define CONFIG_SYS_IBAT4L	(CONFIG_SYS_PCIE2_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT)
 #define CONFIG_SYS_IBAT4U	CONFIG_SYS_DBAT4U

 /*
  * BAT5		128K	Cacheable, non-guarded
  * 0xe400_0000	128K	Init RAM for stack in the CPU DCache (no backing memory)
  */
 #define CONFIG_SYS_DBAT5L	(CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE)
 #define CONFIG_SYS_DBAT5U	(CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
 #define CONFIG_SYS_IBAT5L	CONFIG_SYS_DBAT5L
 #define CONFIG_SYS_IBAT5U	CONFIG_SYS_DBAT5U

 /*
  * BAT6		256M	Cache-inhibited, guarded
  * 0xf000_0000	256M	FLASH
  */
 #define CONFIG_SYS_DBAT6L	(CONFIG_SYS_FLASH_BASE	 | BATL_PP_RW | BATL_CACHEINHIBIT \
 			| BATL_GUARDEDSTORAGE)
 #define CONFIG_SYS_DBAT6U	(CONFIG_SYS_FLASH_BASE	 | BATU_BL_256M | BATU_VS | BATU_VP)
 #define CONFIG_SYS_IBAT6L	(CONFIG_SYS_FLASH_BASE | BATL_PP_RW | BATL_MEMCOHERENCE)
 #define CONFIG_SYS_IBAT6U	CONFIG_SYS_DBAT6U

 /* Map the last 1M of flash where we're running from reset */
 #define CONFIG_SYS_DBAT6L_EARLY	(CONFIG_SYS_MONITOR_BASE_EARLY | BATL_PP_RW \
 				 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
 #define CONFIG_SYS_DBAT6U_EARLY	(CONFIG_SYS_TEXT_BASE | BATU_BL_1M | BATU_VS | BATU_VP)
 #define CONFIG_SYS_IBAT6L_EARLY	(CONFIG_SYS_MONITOR_BASE_EARLY | BATL_PP_RW \
 				 | BATL_MEMCOHERENCE)
 #define CONFIG_SYS_IBAT6U_EARLY	CONFIG_SYS_DBAT6U_EARLY

 /*
  * BAT7		4M	Cache-inhibited, guarded
  * 0xe800_0000	4M	PIXIS
  */
 #define CONFIG_SYS_DBAT7L	(PIXIS_BASE | BATL_PP_RW | BATL_CACHEINHIBIT \
 			| BATL_GUARDEDSTORAGE)
 #define CONFIG_SYS_DBAT7U	(PIXIS_BASE | BATU_BL_1M | BATU_VS | BATU_VP)
 #define CONFIG_SYS_IBAT7L	(PIXIS_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
 #define CONFIG_SYS_IBAT7U	CONFIG_SYS_DBAT7U

 /*
  * Environment
  */
 #ifndef CONFIG_SYS_RAMBOOT
 #define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
 #define CONFIG_ENV_SECT_SIZE	0x20000	/* 126k (one sector) for env */
 #define CONFIG_ENV_SIZE		0x2000
 #else
 #define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - 0x1000)
 #define CONFIG_ENV_SIZE		0x2000
 #endif

 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
 #define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change */

 /*
  * BOOTP options
  */
 #define CONFIG_BOOTP_BOOTFILESIZE

 /*
  * Command line configuration.
  */

 #define CONFIG_WATCHDOG			/* watchdog enabled */
 #define CONFIG_SYS_WATCHDOG_FREQ	5000	/* Feed interval, 5s */

 /*
  * Miscellaneous configurable options
  */
 #define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */

 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 8 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
 #define CONFIG_SYS_BOOTMAPSZ	(256 << 20)	/* Initial Memory map for Linux*/
 #define CONFIG_SYS_BOOTM_LEN	(256 << 20)	/* Increase max gunzip size */

 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
 #endif

 /*
  * Environment Configuration
  */
 #define CONFIG_IPADDR		192.168.1.100

 #define CONFIG_HOSTNAME		unknown
 #define CONFIG_ROOTPATH		"/opt/nfsroot"
 #define CONFIG_BOOTFILE		"uImage"
 #define CONFIG_UBOOTPATH	8610hpcd/u-boot.bin

 #define CONFIG_SERVERIP		192.168.1.1
 #define CONFIG_GATEWAYIP	192.168.1.1
 #define CONFIG_NETMASK		255.255.255.0

 /* default location for tftp and bootm */
 #define CONFIG_LOADADDR		0x10000000

 #if defined(CONFIG_PCI1)
 #define PCI_ENV \
  "pcireg=md ${a}000 3; echo o;md ${a}c00 25; echo i; md ${a}da0 15;" \
 	"echo e;md ${a}e00 9\0" \
  "pci1regs=setenv a e0008; run pcireg\0" \
  "pcierr=md ${a}e00 8; pci d.b $b.0 7 1; pci d.w $b.0 1e 1;" \
 	"pci d.w $b.0 56 1\0" \
  "pcierrc=mw ${a}e00 ffffffff; pci w.b $b.0 7 ff; pci w.w $b.0 1e ffff;" \
 	"pci w.w $b.0 56 ffff\0"	\
  "pci1err=setenv a e0008; run pcierr\0"	\
  "pci1errc=setenv a e0008; run pcierrc\0"
 #else
 #define	PCI_ENV ""
 #endif

 #if defined(CONFIG_PCIE1) || defined(CONFIG_PCIE2)
 #define PCIE_ENV \
  "pciereg=md ${a}000 6; md ${a}020 4; md ${a}bf8 2; echo o;md ${a}c00 25;" \
 	"echo i; md ${a}da0 15; echo e;md ${a}e00 e; echo d; md ${a}f00 c\0" \
  "pcie1regs=setenv a e000a; run pciereg\0"	\
  "pcie2regs=setenv a e0009; run pciereg\0"	\
  "pcieerr=md ${a}020 1; md ${a}e00; pci d.b $b.0 7 1; pci d.w $b.0 1e 1;"\
 	"pci d.w $b.0 56 1; pci d $b.0 104 1; pci d $b.0 110 1;"	\
 	"pci d $b.0 130 1\0" \
  "pcieerrc=mw ${a}020 ffffffff; mw ${a}e00 ffffffff; pci w.b $b.0 7 ff;"\
 	"pci w.w $b.0 1e ffff; pci w.w $b.0 56 ffff; pci w $b.0 104 ffffffff;" \
 	"pci w $b.0 110 ffffffff; pci w $b.0 130 ffffffff\0"		\
  "pciecfg=pci d $b.0 0 20; pci d $b.0 100 e; pci d $b.0 400 69\0"	\
  "pcie1err=setenv a e000a; run pcieerr\0"	\
  "pcie2err=setenv a e0009; run pcieerr\0"	\
  "pcie1errc=setenv a e000a; run pcieerrc\0"	\
  "pcie2errc=setenv a e0009; run pcieerrc\0"
 #else
 #define	PCIE_ENV ""
 #endif

 #define DMA_ENV \
  "dma0=mw ${d}104 ffffffff;mw ${d}110 50000;mw ${d}114 $sad0;mw ${d}118 50000;"\
 	"mw ${d}120 $bc0;mw ${d}100 f03c404; mw ${d}11c $dad0; md ${d}100 9\0" \
  "dma1=mw ${d}184 ffffffff;mw ${d}190 50000;mw ${d}194 $sad1;mw ${d}198 50000;"\
 	"mw ${d}1a0 $bc1;mw ${d}180 f03c404; mw ${d}19c $dad1; md ${d}180 9\0" \
  "dma2=mw ${d}204 ffffffff;mw ${d}210 50000;mw ${d}214 $sad2;mw ${d}218 50000;"\
 	"mw ${d}220 $bc2;mw ${d}200 f03c404; mw ${d}21c $dad2; md ${d}200 9\0" \
  "dma3=mw ${d}284 ffffffff;mw ${d}290 50000;mw ${d}294 $sad3;mw ${d}298 50000;"\
 	"mw ${d}2a0 $bc3;mw ${d}280 f03c404; mw ${d}29c $dad3; md ${d}280 9\0"

 #ifdef ENV_DEBUG
 #define	CONFIG_EXTRA_ENV_SETTINGS				\
 "netdev=eth0\0"							\
 "uboot=" __stringify(CONFIG_UBOOTPATH) "\0"			\
 "tftpflash=tftpboot $loadaddr $uboot; "				\
 	"protect off " __stringify(CONFIG_SYS_TEXT_BASE)	\
 		" +$filesize; "	\
 	"erase " __stringify(CONFIG_SYS_TEXT_BASE)		\
 		" +$filesize; "	\
 	"cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE)	\
 		" $filesize; "	\
 	"protect on " __stringify(CONFIG_SYS_TEXT_BASE)		\
 		" +$filesize; "	\
 	"cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE)	\
 		" $filesize\0"	\
 "consoledev=ttyS0\0"						\
 "ramdiskaddr=0x18000000\0"					\
 "ramdiskfile=8610hpcd/ramdisk.uboot\0"				\
 "fdtaddr=0x17c00000\0"						\
 "fdtfile=8610hpcd/mpc8610_hpcd.dtb\0"				\
 "bdev=sda3\0"					\
 "en-wd=mw.b f8100010 0x08; echo -expect:- 08; md.b f8100010 1\0" \
 "dis-wd=mw.b f8100010 0x00; echo -expect:- 00; md.b f8100010 1\0" \
 "maxcpus=1"	\
 "eoi=mw e00400b0 0\0"						\
 "iack=md e00400a0 1\0"						\
 "ddrreg=md ${a}000 8; md ${a}080 8;md ${a}100 d; md ${a}140 4;" \
 	"md ${a}bf0 4; md ${a}e00 3; md ${a}e20 3; md ${a}e40 7;" \
 	"md ${a}f00 5\0" \
 "ddr1regs=setenv a e0002; run ddrreg\0" \
 "gureg=md ${a}000 2c; md ${a}0b0 1; md ${a}0c0 1; md ${a}800 1;" \
 	"md ${a}900 6; md ${a}a00 1; md ${a}b20 3; md ${a}e00 1;" \
 	"md ${a}e60 1; md ${a}ef0 1d\0" \
 "guregs=setenv a e00e0; run gureg\0" \
 "mcmreg=md ${a}000 1b; md ${a}bf8 2; md ${a}e00 5\0" \
 "mcmregs=setenv a e0001; run mcmreg\0" \
 "diuregs=md e002c000 1d\0" \
 "dium=mw e002c01c\0" \
 "diuerr=md e002c014 1\0" \
 "pmregs=md e00e1000 2b\0" \
 "lawregs=md e0000c08 4b\0" \
 "lbcregs=md e0005000 36\0" \
 "dma0regs=md e0021100 12\0" \
 "dma1regs=md e0021180 12\0" \
 "dma2regs=md e0021200 12\0" \
 "dma3regs=md e0021280 12\0" \
  PCI_ENV \
  PCIE_ENV \
  DMA_ENV
 #else
 #define CONFIG_EXTRA_ENV_SETTINGS				\
 	"netdev=eth0\0"						\
 	"uboot=" __stringify(CONFIG_UBOOTPATH) "\0"		\
 	"consoledev=ttyS0\0"					\
 	"ramdiskaddr=0x18000000\0"				\
 	"ramdiskfile=8610hpcd/ramdisk.uboot\0"			\
 	"fdtaddr=0x17c00000\0"					\
 	"fdtfile=8610hpcd/mpc8610_hpcd.dtb\0"			\
 	"bdev=sda3\0"
 #endif

 #define CONFIG_NFSBOOTCOMMAND					\
  "setenv bootargs root=/dev/nfs rw "				\
 	"nfsroot=$serverip:$rootpath "				\
 	"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
 	"console=$consoledev,$baudrate $othbootargs;"		\
  "tftp $loadaddr $bootfile;"					\
  "tftp $fdtaddr $fdtfile;"					\
  "bootm $loadaddr - $fdtaddr"

 #define CONFIG_RAMBOOTCOMMAND \
  "setenv bootargs root=/dev/ram rw "				\
 	"console=$consoledev,$baudrate $othbootargs;"		\
  "tftp $ramdiskaddr $ramdiskfile;"				\
  "tftp $loadaddr $bootfile;"					\
  "tftp $fdtaddr $fdtfile;"					\
  "bootm $loadaddr $ramdiskaddr $fdtaddr"

 #define CONFIG_BOOTCOMMAND		\
  "setenv bootargs root=/dev/$bdev rw "	\
 	"console=$consoledev,$baudrate $othbootargs;"	\
  "tftp $loadaddr $bootfile;"		\
  "tftp $fdtaddr $fdtfile;"		\
  "bootm $loadaddr - $fdtaddr"

 #endif	/* __CONFIG_H */
	/*
	* Copyright 2007-2011 Freescale Semiconductor, Inc.
	*
	* SPDX-License-Identifier: GPL-2.0
	*/

	/*
	* MPC8610HPCD board configuration file
	*/

	#ifndef __CONFIG_H
	#define __CONFIG_H

	/* High Level Configuration Options */
	#define CONFIG_LINUX_RESET_VEC 0x100 /* Reset vector used by Linux */

	/* video */
	#define CONFIG_FSL_DIU_FB

	#ifdef CONFIG_FSL_DIU_FB
	#define CONFIG_SYS_DIU_ADDR (CONFIG_SYS_CCSRBAR + 0x2c000)
	#define CONFIG_VIDEO_LOGO
	#define CONFIG_VIDEO_BMP_LOGO
	#endif

	#ifdef RUN_DIAG
	#define CONFIG_SYS_DIAG_ADDR 0xff800000
	#endif

	/*
	* virtual address to be used for temporary mappings. There
	* should be 128k free at this VA.
	*/
	#define CONFIG_SYS_SCRATCH_VA 0xc0000000

	#define CONFIG_PCI1 1 /* PCI controller 1 */
	#define CONFIG_PCIE1 1 /* PCIe 1 connected to ULI bridge */
	#define CONFIG_PCIE2 1 /* PCIe 2 connected to slot */
	#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */
	#define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */
	#define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */

	#define CONFIG_ENV_OVERWRITE
	#define CONFIG_INTERRUPTS /* enable pci, srio, ddr interrupts */

	#define CONFIG_BAT_RW 1 /* Use common BAT rw code */
	#define CONFIG_HIGH_BATS 1 /* High BATs supported & enabled */
	#define CONFIG_ALTIVEC 1

	/*
	* L2CR setup -- make sure this is right for your board!
	*/
	#define CONFIG_SYS_L2
	#define L2_INIT 0
	#define L2_ENABLE (L2CR_L2E \|0x00100000 )

	#ifndef CONFIG_SYS_CLK_FREQ
	#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0)
	#endif

	#define CONFIG_MISC_INIT_R 1

	#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest region */
	#define CONFIG_SYS_MEMTEST_END 0x00400000

	/*
	* Base addresses -- Note these are effective addresses where the
	* actual resources get mapped (not physical addresses)
	*/
	#define CONFIG_SYS_CCSRBAR 0xe0000000 /* relocated CCSRBAR */
	#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */

	#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
	#define CONFIG_SYS_CCSRBAR_PHYS_HIGH 0x0
	#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR_PHYS_LOW

	/* DDR Setup */
	#undef CONFIG_FSL_DDR_INTERACTIVE
	#define CONFIG_SPD_EEPROM /* Use SPD for DDR */
	#define CONFIG_DDR_SPD

	#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */
	#define CONFIG_MEM_INIT_VALUE 0xDeadBeef

	#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/
	#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
	#define CONFIG_SYS_MAX_DDR_BAT_SIZE 0x80000000 /* BAT mapping size */
	#define CONFIG_VERY_BIG_RAM

	#define CONFIG_DIMM_SLOTS_PER_CTLR 1
	#define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR)

	#define SPD_EEPROM_ADDRESS 0x51 /* CTLR 0 DIMM 0 */

	/* These are used when DDR doesn't use SPD. */
	#define CONFIG_SYS_SDRAM_SIZE 256 /* DDR is 256MB */

	#if 0 /* TODO */
	#define CONFIG_SYS_DDR_CS0_BNDS 0x0000000F
	#define CONFIG_SYS_DDR_CS0_CONFIG 0x80010202 /* Enable, no interleaving */
	#define CONFIG_SYS_DDR_TIMING_3 0x00000000
	#define CONFIG_SYS_DDR_TIMING_0 0x00260802
	#define CONFIG_SYS_DDR_TIMING_1 0x3935d322
	#define CONFIG_SYS_DDR_TIMING_2 0x14904cc8
	#define CONFIG_SYS_DDR_MODE_1 0x00480432
	#define CONFIG_SYS_DDR_MODE_2 0x00000000
	#define CONFIG_SYS_DDR_INTERVAL 0x06180100
	#define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef
	#define CONFIG_SYS_DDR_CLK_CTRL 0x03800000
	#define CONFIG_SYS_DDR_OCD_CTRL 0x00000000
	#define CONFIG_SYS_DDR_OCD_STATUS 0x00000000
	#define CONFIG_SYS_DDR_CONTROL 0xe3008000 /* Type = DDR2 */
	#define CONFIG_SYS_DDR_CONTROL2 0x04400010

	#define CONFIG_SYS_DDR_ERR_INT_EN 0x00000000
	#define CONFIG_SYS_DDR_ERR_DIS 0x00000000
	#define CONFIG_SYS_DDR_SBE 0x000f0000

	#endif

	#define CONFIG_ID_EEPROM
	#define CONFIG_SYS_I2C_EEPROM_NXID
	#define CONFIG_ID_EEPROM
	#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
	#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1

	#define CONFIG_SYS_FLASH_BASE 0xf0000000 /* start of FLASH 128M */
	#define CONFIG_SYS_FLASH_BASE2 0xf8000000

	#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2}

	#define CONFIG_SYS_BR0_PRELIM 0xf8001001 /* port size 16bit */
	#define CONFIG_SYS_OR0_PRELIM 0xf8006e65 /* 128MB NOR Flash*/

	#define CONFIG_SYS_BR1_PRELIM 0xf0001001 /* port size 16bit */
	#define CONFIG_SYS_OR1_PRELIM 0xf8006e65 /* 128MB Promjet */
	#if 0 /* TODO */
	#define CONFIG_SYS_BR2_PRELIM 0xf0000000
	#define CONFIG_SYS_OR2_PRELIM 0xf0000000 /* 256MB NAND Flash - bank 1 */
	#endif
	#define CONFIG_SYS_BR3_PRELIM 0xe8000801 /* port size 8bit */
	#define CONFIG_SYS_OR3_PRELIM 0xfff06ff7 /* 1MB PIXIS area*/

	#define CONFIG_FSL_PIXIS 1 /* use common PIXIS code */
	#define PIXIS_BASE 0xe8000000 /* PIXIS registers */
	#define PIXIS_ID 0x0 /* Board ID at offset 0 */
	#define PIXIS_VER 0x1 /* Board version at offset 1 */
	#define PIXIS_PVER 0x2 /* PIXIS FPGA version at offset 2 */
	#define PIXIS_RST 0x4 /* PIXIS Reset Control register */
	#define PIXIS_AUX 0x6 /* PIXIS Auxiliary register; Scratch */
	#define PIXIS_SPD 0x7 /* Register for SYSCLK speed */
	#define PIXIS_BRDCFG0 0x8 /* PIXIS Board Configuration Register0*/
	#define PIXIS_VCTL 0x10 /* VELA Control Register */
	#define PIXIS_VCFGEN0 0x12 /* VELA Config Enable 0 */
	#define PIXIS_VCFGEN1 0x13 /* VELA Config Enable 1 */
	#define PIXIS_VBOOT 0x16 /* VELA VBOOT Register */
	#define PIXIS_VSPEED0 0x17 /* VELA VSpeed 0 */
	#define PIXIS_VSPEED1 0x18 /* VELA VSpeed 1 */
	#define PIXIS_VCLKH 0x19 /* VELA VCLKH register */
	#define PIXIS_VCLKL 0x1A /* VELA VCLKL register */
	#define CONFIG_SYS_PIXIS_VBOOT_MASK 0xC0 /* Reset altbank mask */

	#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */
	#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */

	#undef CONFIG_SYS_FLASH_CHECKSUM
	#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
	#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
	#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
	#define CONFIG_SYS_MONITOR_BASE_EARLY 0xfff00000 /* early monitor loc */

	#define CONFIG_FLASH_CFI_DRIVER
	#define CONFIG_SYS_FLASH_CFI
	#define CONFIG_SYS_FLASH_EMPTY_INFO

	#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
	#define CONFIG_SYS_RAMBOOT
	#else
	#undef CONFIG_SYS_RAMBOOT
	#endif

	#if defined(CONFIG_SYS_RAMBOOT)
	#undef CONFIG_SPD_EEPROM
	#define CONFIG_SYS_SDRAM_SIZE 256
	#endif

	#undef CONFIG_CLOCKS_IN_MHZ

	#define CONFIG_SYS_INIT_RAM_LOCK 1
	#ifndef CONFIG_SYS_INIT_RAM_LOCK
	#define CONFIG_SYS_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */
	#else
	#define CONFIG_SYS_INIT_RAM_ADDR 0xe4000000 /* Initial RAM address */
	#endif
	#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in RAM */

	#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
	#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET

	#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 KB for Mon */
	#define CONFIG_SYS_MALLOC_LEN (6 * 1024 * 1024) /* Reserved for malloc */

	/* Serial Port */
	#define CONFIG_CONS_INDEX 1
	#define CONFIG_SYS_NS16550_SERIAL
	#define CONFIG_SYS_NS16550_REG_SIZE 1
	#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)

	#define CONFIG_SYS_BAUDRATE_TABLE \
	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}

	#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
	#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)

	/* maximum size of the flat tree (8K) */
	#define OF_FLAT_TREE_MAX_SIZE 8192

	/*
	* I2C
	*/
	#define CONFIG_SYS_I2C
	#define CONFIG_SYS_I2C_FSL
	#define CONFIG_SYS_FSL_I2C_SPEED 400000
	#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
	#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
	#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} }

	/*
	* General PCI
	* Addresses are mapped 1-1.
	*/
	#define CONFIG_SYS_PCI1_MEM_BUS 0x80000000
	#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BUS
	#define CONFIG_SYS_PCI1_MEM_VIRT CONFIG_SYS_PCI1_MEM_BUS
	#define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */
	#define CONFIG_SYS_PCI1_IO_BUS 0x0000000
	#define CONFIG_SYS_PCI1_IO_PHYS 0xe1000000
	#define CONFIG_SYS_PCI1_IO_VIRT 0xe1000000
	#define CONFIG_SYS_PCI1_IO_SIZE 0x00100000 /* 1M */

	/* controller 1, Base address 0xa000 */
	#define CONFIG_SYS_PCIE1_NAME "ULI"
	#define CONFIG_SYS_PCIE1_MEM_BUS 0xa0000000
	#define CONFIG_SYS_PCIE1_MEM_PHYS CONFIG_SYS_PCIE1_MEM_BUS
	#define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000 /* 256M */
	#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
	#define CONFIG_SYS_PCIE1_IO_PHYS 0xe3000000
	#define CONFIG_SYS_PCIE1_IO_SIZE 0x00100000 /* 1M */

	/* controller 2, Base Address 0x9000 */
	#define CONFIG_SYS_PCIE2_NAME "Slot 1"
	#define CONFIG_SYS_PCIE2_MEM_BUS 0x90000000
	#define CONFIG_SYS_PCIE2_MEM_PHYS CONFIG_SYS_PCIE2_MEM_BUS
	#define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */
	#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 /* reuse mem LAW */
	#define CONFIG_SYS_PCIE2_IO_PHYS 0xe2000000
	#define CONFIG_SYS_PCIE2_IO_SIZE 0x00100000 /* 1M */

	#if defined(CONFIG_PCI)

	#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */

	#define CONFIG_ULI526X
	#ifdef CONFIG_ULI526X
	#endif

	/************************************************************
	* USB support
	************************************************************/
	#define CONFIG_PCI_OHCI 1
	#define CONFIG_USB_OHCI_NEW 1
	#define CONFIG_SYS_USB_OHCI_SLOT_NAME "ohci_pci"
	#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15
	#define CONFIG_SYS_OHCI_SWAP_REG_ACCESS 1

	#if !defined(CONFIG_PCI_PNP)
	#define PCI_ENET0_IOADDR 0xe0000000
	#define PCI_ENET0_MEMADDR 0xe0000000
	#define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */
	#endif

	#ifdef CONFIG_SCSI_AHCI
	#define CONFIG_SATA_ULI5288
	#define CONFIG_SYS_SCSI_MAX_SCSI_ID 4
	#define CONFIG_SYS_SCSI_MAX_LUN 1
	#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * CONFIG_SYS_SCSI_MAX_LUN)
	#define CONFIG_SYS_SCSI_MAXDEVICE CONFIG_SYS_SCSI_MAX_DEVICE
	#endif

	#endif /* CONFIG_PCI */

	/*
	* BAT0 2G Cacheable, non-guarded
	* 0x0000_0000 2G DDR
	*/
	#define CONFIG_SYS_DBAT0L (BATL_PP_RW)
	#define CONFIG_SYS_IBAT0L (BATL_PP_RW)

	/*
	* BAT1 1G Cache-inhibited, guarded
	* 0x8000_0000 256M PCI-1 Memory
	* 0xa000_0000 256M PCI-Express 1 Memory
	* 0x9000_0000 256M PCI-Express 2 Memory
	*/

	#define CONFIG_SYS_DBAT1L (CONFIG_SYS_PCI1_MEM_PHYS \| BATL_PP_RW \| BATL_CACHEINHIBIT \
	\| BATL_GUARDEDSTORAGE)
	#define CONFIG_SYS_DBAT1U (CONFIG_SYS_PCI1_MEM_VIRT \| BATU_BL_1G \| BATU_VS \| BATU_VP)
	#define CONFIG_SYS_IBAT1L (CONFIG_SYS_PCI1_MEM_PHYS \| BATL_PP_RW \| BATL_CACHEINHIBIT)
	#define CONFIG_SYS_IBAT1U CONFIG_SYS_DBAT1U

	/*
	* BAT2 16M Cache-inhibited, guarded
	* 0xe100_0000 1M PCI-1 I/O
	*/

	#define CONFIG_SYS_DBAT2L (CONFIG_SYS_PCI1_IO_PHYS \| BATL_PP_RW \| BATL_CACHEINHIBIT \
	\| BATL_GUARDEDSTORAGE)
	#define CONFIG_SYS_DBAT2U (CONFIG_SYS_PCI1_IO_VIRT \| BATU_BL_16M \| BATU_VS \| BATU_VP)
	#define CONFIG_SYS_IBAT2L (CONFIG_SYS_PCI1_IO_PHYS \| BATL_PP_RW \| BATL_CACHEINHIBIT)
	#define CONFIG_SYS_IBAT2U CONFIG_SYS_DBAT2U

	/*
	* BAT3 4M Cache-inhibited, guarded
	* 0xe000_0000 4M CCSR
	*/

	#define CONFIG_SYS_DBAT3L (CONFIG_SYS_CCSRBAR \| BATL_PP_RW \| BATL_CACHEINHIBIT \
	\| BATL_GUARDEDSTORAGE)
	#define CONFIG_SYS_DBAT3U (CONFIG_SYS_CCSRBAR \| BATU_BL_1M \| BATU_VS \| BATU_VP)
	#define CONFIG_SYS_IBAT3L (CONFIG_SYS_CCSRBAR \| BATL_PP_RW \| BATL_CACHEINHIBIT)
	#define CONFIG_SYS_IBAT3U CONFIG_SYS_DBAT3U

	#if (CONFIG_SYS_CCSRBAR_DEFAULT != CONFIG_SYS_CCSRBAR)
	#define CONFIG_SYS_CCSR_DEFAULT_DBATL (CONFIG_SYS_CCSRBAR_DEFAULT \
	\| BATL_PP_RW \| BATL_CACHEINHIBIT \
	\| BATL_GUARDEDSTORAGE)
	#define CONFIG_SYS_CCSR_DEFAULT_DBATU (CONFIG_SYS_CCSRBAR_DEFAULT \
	\| BATU_BL_1M \| BATU_VS \| BATU_VP)
	#define CONFIG_SYS_CCSR_DEFAULT_IBATL (CONFIG_SYS_CCSRBAR_DEFAULT \
	\| BATL_PP_RW \| BATL_CACHEINHIBIT)
	#define CONFIG_SYS_CCSR_DEFAULT_IBATU CONFIG_SYS_CCSR_DEFAULT_DBATU
	#endif

	/*
	* BAT4 32M Cache-inhibited, guarded
	* 0xe200_0000 1M PCI-Express 2 I/O
	* 0xe300_0000 1M PCI-Express 1 I/O
	*/

	#define CONFIG_SYS_DBAT4L (CONFIG_SYS_PCIE2_IO_PHYS \| BATL_PP_RW \| BATL_CACHEINHIBIT \
	\| BATL_GUARDEDSTORAGE)
	#define CONFIG_SYS_DBAT4U (CONFIG_SYS_PCIE2_IO_PHYS \| BATU_BL_32M \| BATU_VS \| BATU_VP)
	#define CONFIG_SYS_IBAT4L (CONFIG_SYS_PCIE2_IO_PHYS \| BATL_PP_RW \| BATL_CACHEINHIBIT)
	#define CONFIG_SYS_IBAT4U CONFIG_SYS_DBAT4U

	/*
	* BAT5 128K Cacheable, non-guarded
	* 0xe400_0000 128K Init RAM for stack in the CPU DCache (no backing memory)
	*/
	#define CONFIG_SYS_DBAT5L (CONFIG_SYS_INIT_RAM_ADDR \| BATL_PP_RW \| BATL_MEMCOHERENCE)
	#define CONFIG_SYS_DBAT5U (CONFIG_SYS_INIT_RAM_ADDR \| BATU_BL_128K \| BATU_VS \| BATU_VP)
	#define CONFIG_SYS_IBAT5L CONFIG_SYS_DBAT5L
	#define CONFIG_SYS_IBAT5U CONFIG_SYS_DBAT5U

	/*
	* BAT6 256M Cache-inhibited, guarded
	* 0xf000_0000 256M FLASH
	*/
	#define CONFIG_SYS_DBAT6L (CONFIG_SYS_FLASH_BASE \| BATL_PP_RW \| BATL_CACHEINHIBIT \
	\| BATL_GUARDEDSTORAGE)
	#define CONFIG_SYS_DBAT6U (CONFIG_SYS_FLASH_BASE \| BATU_BL_256M \| BATU_VS \| BATU_VP)
	#define CONFIG_SYS_IBAT6L (CONFIG_SYS_FLASH_BASE \| BATL_PP_RW \| BATL_MEMCOHERENCE)
	#define CONFIG_SYS_IBAT6U CONFIG_SYS_DBAT6U

	/* Map the last 1M of flash where we're running from reset */
	#define CONFIG_SYS_DBAT6L_EARLY (CONFIG_SYS_MONITOR_BASE_EARLY \| BATL_PP_RW \
	\| BATL_CACHEINHIBIT \| BATL_GUARDEDSTORAGE)
	#define CONFIG_SYS_DBAT6U_EARLY (CONFIG_SYS_TEXT_BASE \| BATU_BL_1M \| BATU_VS \| BATU_VP)
	#define CONFIG_SYS_IBAT6L_EARLY (CONFIG_SYS_MONITOR_BASE_EARLY \| BATL_PP_RW \
	\| BATL_MEMCOHERENCE)
	#define CONFIG_SYS_IBAT6U_EARLY CONFIG_SYS_DBAT6U_EARLY

	/*
	* BAT7 4M Cache-inhibited, guarded
	* 0xe800_0000 4M PIXIS
	*/
	#define CONFIG_SYS_DBAT7L (PIXIS_BASE \| BATL_PP_RW \| BATL_CACHEINHIBIT \
	\| BATL_GUARDEDSTORAGE)
	#define CONFIG_SYS_DBAT7U (PIXIS_BASE \| BATU_BL_1M \| BATU_VS \| BATU_VP)
	#define CONFIG_SYS_IBAT7L (PIXIS_BASE \| BATL_PP_RW \| BATL_CACHEINHIBIT)
	#define CONFIG_SYS_IBAT7U CONFIG_SYS_DBAT7U

	/*
	* Environment
	*/
	#ifndef CONFIG_SYS_RAMBOOT
	#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
	#define CONFIG_ENV_SECT_SIZE 0x20000 /* 126k (one sector) for env */
	#define CONFIG_ENV_SIZE 0x2000
	#else
	#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
	#define CONFIG_ENV_SIZE 0x2000
	#endif

	#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
	#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */

	/*
	* BOOTP options
	*/
	#define CONFIG_BOOTP_BOOTFILESIZE

	/*
	* Command line configuration.
	*/

	#define CONFIG_WATCHDOG /* watchdog enabled */
	#define CONFIG_SYS_WATCHDOG_FREQ 5000 /* Feed interval, 5s */

	/*
	* Miscellaneous configurable options
	*/
	#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */

	/*
	* For booting Linux, the board info and command line data
	* have to be in the first 8 MB of memory, since this is
	* the maximum mapped by the Linux kernel during initialization.
	*/
	#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux*/
	#define CONFIG_SYS_BOOTM_LEN (256 << 20) /* Increase max gunzip size */

	#if defined(CONFIG_CMD_KGDB)
	#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
	#endif

	/*
	* Environment Configuration
	*/
	#define CONFIG_IPADDR 192.168.1.100

	#define CONFIG_HOSTNAME unknown
	#define CONFIG_ROOTPATH "/opt/nfsroot"
	#define CONFIG_BOOTFILE "uImage"
	#define CONFIG_UBOOTPATH 8610hpcd/u-boot.bin

	#define CONFIG_SERVERIP 192.168.1.1
	#define CONFIG_GATEWAYIP 192.168.1.1
	#define CONFIG_NETMASK 255.255.255.0

	/* default location for tftp and bootm */
	#define CONFIG_LOADADDR 0x10000000

	#if defined(CONFIG_PCI1)
	#define PCI_ENV \
	"pcireg=md ${a}000 3; echo o;md ${a}c00 25; echo i; md ${a}da0 15;" \
	"echo e;md ${a}e00 9\0" \
	"pci1regs=setenv a e0008; run pcireg\0" \
	"pcierr=md ${a}e00 8; pci d.b $b.0 7 1; pci d.w $b.0 1e 1;" \
	"pci d.w $b.0 56 1\0" \
	"pcierrc=mw ${a}e00 ffffffff; pci w.b $b.0 7 ff; pci w.w $b.0 1e ffff;" \
	"pci w.w $b.0 56 ffff\0" \
	"pci1err=setenv a e0008; run pcierr\0" \
	"pci1errc=setenv a e0008; run pcierrc\0"
	#else
	#define PCI_ENV ""
	#endif

	#if defined(CONFIG_PCIE1) \|\| defined(CONFIG_PCIE2)
	#define PCIE_ENV \
	"pciereg=md ${a}000 6; md ${a}020 4; md ${a}bf8 2; echo o;md ${a}c00 25;" \
	"echo i; md ${a}da0 15; echo e;md ${a}e00 e; echo d; md ${a}f00 c\0" \
	"pcie1regs=setenv a e000a; run pciereg\0" \
	"pcie2regs=setenv a e0009; run pciereg\0" \
	"pcieerr=md ${a}020 1; md ${a}e00; pci d.b $b.0 7 1; pci d.w $b.0 1e 1;"\
	"pci d.w $b.0 56 1; pci d $b.0 104 1; pci d $b.0 110 1;" \
	"pci d $b.0 130 1\0" \
	"pcieerrc=mw ${a}020 ffffffff; mw ${a}e00 ffffffff; pci w.b $b.0 7 ff;"\
	"pci w.w $b.0 1e ffff; pci w.w $b.0 56 ffff; pci w $b.0 104 ffffffff;" \
	"pci w $b.0 110 ffffffff; pci w $b.0 130 ffffffff\0" \
	"pciecfg=pci d $b.0 0 20; pci d $b.0 100 e; pci d $b.0 400 69\0" \
	"pcie1err=setenv a e000a; run pcieerr\0" \
	"pcie2err=setenv a e0009; run pcieerr\0" \
	"pcie1errc=setenv a e000a; run pcieerrc\0" \
	"pcie2errc=setenv a e0009; run pcieerrc\0"
	#else
	#define PCIE_ENV ""
	#endif

	#define DMA_ENV \
	"dma0=mw ${d}104 ffffffff;mw ${d}110 50000;mw ${d}114 $sad0;mw ${d}118 50000;"\
	"mw ${d}120 $bc0;mw ${d}100 f03c404; mw ${d}11c $dad0; md ${d}100 9\0" \
	"dma1=mw ${d}184 ffffffff;mw ${d}190 50000;mw ${d}194 $sad1;mw ${d}198 50000;"\
	"mw ${d}1a0 $bc1;mw ${d}180 f03c404; mw ${d}19c $dad1; md ${d}180 9\0" \
	"dma2=mw ${d}204 ffffffff;mw ${d}210 50000;mw ${d}214 $sad2;mw ${d}218 50000;"\
	"mw ${d}220 $bc2;mw ${d}200 f03c404; mw ${d}21c $dad2; md ${d}200 9\0" \
	"dma3=mw ${d}284 ffffffff;mw ${d}290 50000;mw ${d}294 $sad3;mw ${d}298 50000;"\
	"mw ${d}2a0 $bc3;mw ${d}280 f03c404; mw ${d}29c $dad3; md ${d}280 9\0"

	#ifdef ENV_DEBUG
	#define CONFIG_EXTRA_ENV_SETTINGS \
	"netdev=eth0\0" \
	"uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \
	"tftpflash=tftpboot $loadaddr $uboot; " \
	"protect off " __stringify(CONFIG_SYS_TEXT_BASE) \
	" +$filesize; " \
	"erase " __stringify(CONFIG_SYS_TEXT_BASE) \
	" +$filesize; " \
	"cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \
	" $filesize; " \
	"protect on " __stringify(CONFIG_SYS_TEXT_BASE) \
	" +$filesize; " \
	"cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \
	" $filesize\0" \
	"consoledev=ttyS0\0" \
	"ramdiskaddr=0x18000000\0" \
	"ramdiskfile=8610hpcd/ramdisk.uboot\0" \
	"fdtaddr=0x17c00000\0" \
	"fdtfile=8610hpcd/mpc8610_hpcd.dtb\0" \
	"bdev=sda3\0" \
	"en-wd=mw.b f8100010 0x08; echo -expect:- 08; md.b f8100010 1\0" \
	"dis-wd=mw.b f8100010 0x00; echo -expect:- 00; md.b f8100010 1\0" \
	"maxcpus=1" \
	"eoi=mw e00400b0 0\0" \
	"iack=md e00400a0 1\0" \
	"ddrreg=md ${a}000 8; md ${a}080 8;md ${a}100 d; md ${a}140 4;" \
	"md ${a}bf0 4; md ${a}e00 3; md ${a}e20 3; md ${a}e40 7;" \
	"md ${a}f00 5\0" \
	"ddr1regs=setenv a e0002; run ddrreg\0" \
	"gureg=md ${a}000 2c; md ${a}0b0 1; md ${a}0c0 1; md ${a}800 1;" \
	"md ${a}900 6; md ${a}a00 1; md ${a}b20 3; md ${a}e00 1;" \
	"md ${a}e60 1; md ${a}ef0 1d\0" \
	"guregs=setenv a e00e0; run gureg\0" \
	"mcmreg=md ${a}000 1b; md ${a}bf8 2; md ${a}e00 5\0" \
	"mcmregs=setenv a e0001; run mcmreg\0" \
	"diuregs=md e002c000 1d\0" \
	"dium=mw e002c01c\0" \
	"diuerr=md e002c014 1\0" \
	"pmregs=md e00e1000 2b\0" \
	"lawregs=md e0000c08 4b\0" \
	"lbcregs=md e0005000 36\0" \
	"dma0regs=md e0021100 12\0" \
	"dma1regs=md e0021180 12\0" \
	"dma2regs=md e0021200 12\0" \
	"dma3regs=md e0021280 12\0" \
	PCI_ENV \
	PCIE_ENV \
	DMA_ENV
	#else
	#define CONFIG_EXTRA_ENV_SETTINGS \
	"netdev=eth0\0" \
	"uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \
	"consoledev=ttyS0\0" \
	"ramdiskaddr=0x18000000\0" \
	"ramdiskfile=8610hpcd/ramdisk.uboot\0" \
	"fdtaddr=0x17c00000\0" \
	"fdtfile=8610hpcd/mpc8610_hpcd.dtb\0" \
	"bdev=sda3\0"
	#endif

	#define CONFIG_NFSBOOTCOMMAND \
	"setenv bootargs root=/dev/nfs rw " \
	"nfsroot=$serverip:$rootpath " \
	"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
	"console=$consoledev,$baudrate $othbootargs;" \
	"tftp $loadaddr $bootfile;" \
	"tftp $fdtaddr $fdtfile;" \
	"bootm $loadaddr - $fdtaddr"

	#define CONFIG_RAMBOOTCOMMAND \
	"setenv bootargs root=/dev/ram rw " \
	"console=$consoledev,$baudrate $othbootargs;" \
	"tftp $ramdiskaddr $ramdiskfile;" \
	"tftp $loadaddr $bootfile;" \
	"tftp $fdtaddr $fdtfile;" \
	"bootm $loadaddr $ramdiskaddr $fdtaddr"

	#define CONFIG_BOOTCOMMAND \
	"setenv bootargs root=/dev/$bdev rw " \
	"console=$consoledev,$baudrate $othbootargs;" \
	"tftp $loadaddr $bootfile;" \
	"tftp $fdtaddr $fdtfile;" \
	"bootm $loadaddr - $fdtaddr"

	#endif /* __CONFIG_H */