include/configs/qong.h - github/trini/u-boot - Gitiles

 /*
  * Copyright (C) 2009, Ilya Yanok, Emcraft Systems, <yanok@emcraft.com>
  *
  * Configuration settings for the Dave/DENX QongEVB-LITE board.
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */

 #ifndef __CONFIG_H
 #define __CONFIG_H

 #include <asm/arch/imx-regs.h>

 /* High Level Configuration Options */
 #define CONFIG_MX31			/* This is a mx31 */
 #define CONFIG_QONG

 #define CONFIG_DISPLAY_CPUINFO
 #define CONFIG_DISPLAY_BOARDINFO

 #define CONFIG_SYS_TEXT_BASE 0xa0000000

 #define CONFIG_CMDLINE_TAG			/* enable passing of ATAGs */
 #define CONFIG_SETUP_MEMORY_TAGS
 #define CONFIG_INITRD_TAG

 /*
  * Size of malloc() pool
  */
 #define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + 1536 * 1024)

 /*
  * Hardware drivers
  */

 #define CONFIG_MXC_UART
 #define CONFIG_MXC_UART_BASE	UART1_BASE

 #define CONFIG_MXC_GPIO
 #define CONFIG_HW_WATCHDOG
 #define CONFIG_IMX_WATCHDOG

 #define CONFIG_MXC_SPI
 #define CONFIG_DEFAULT_SPI_BUS	1
 #define CONFIG_DEFAULT_SPI_MODE	(SPI_MODE_0 | SPI_CS_HIGH)
 #define CONFIG_RTC_MC13XXX

 #define CONFIG_POWER
 #define CONFIG_POWER_SPI
 #define CONFIG_POWER_FSL
 #define CONFIG_FSL_PMIC_BUS	1
 #define CONFIG_FSL_PMIC_CS	0
 #define CONFIG_FSL_PMIC_CLK	100000
 #define CONFIG_FSL_PMIC_MODE	(SPI_MODE_0 | SPI_CS_HIGH)
 #define CONFIG_FSL_PMIC_BITLEN	32

 /* FPGA */
 #define CONFIG_FPGA
 #define CONFIG_QONG_FPGA
 #define CONFIG_FPGA_BASE	(CS1_BASE)
 #define CONFIG_FPGA_LATTICE
 #define CONFIG_FPGA_COUNT	1

 #ifdef CONFIG_QONG_FPGA
 /* Ethernet */
 #define CONFIG_DNET
 #define CONFIG_DNET_BASE	(CS1_BASE + QONG_FPGA_PERIPH_SIZE)

 /* Framebuffer and LCD */
 #define CONFIG_VIDEO
 #define CONFIG_CFB_CONSOLE
 #define CONFIG_VIDEO_MX3
 #define CONFIG_VIDEO_LOGO
 #define CONFIG_VIDEO_SW_CURSOR
 #define CONFIG_VGA_AS_SINGLE_DEVICE
 #define CONFIG_SYS_CONSOLE_IS_IN_ENV
 #define CONFIG_SPLASH_SCREEN
 #define CONFIG_CMD_BMP
 #define CONFIG_BMP_16BPP
 #define CONFIG_VIDEO_BMP_GZIP
 #define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE	(512 << 10)

 /* USB */
 #define CONFIG_CMD_USB
 #ifdef CONFIG_CMD_USB
 #define CONFIG_USB_EHCI			/* Enable EHCI USB support */
 #define CONFIG_USB_EHCI_MXC
 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 #define CONFIG_MXC_USB_PORT	2
 #define CONFIG_MXC_USB_PORTSC	(MXC_EHCI_MODE_ULPI | MXC_EHCI_UTMI_8BIT)
 #define CONFIG_MXC_USB_FLAGS	MXC_EHCI_POWER_PINS_ENABLED
 #define CONFIG_EHCI_IS_TDI
 #define CONFIG_USB_STORAGE
 #define CONFIG_DOS_PARTITION
 #define CONFIG_SUPPORT_VFAT
 #define CONFIG_CMD_EXT2
 #define CONFIG_CMD_FAT
 #endif /* CONFIG_CMD_USB */

 /*
  * Reducing the ARP timeout from default 5 seconds to 200ms we speed up the
  * initial TFTP transfer, should the user wish one, significantly.
  */
 #define CONFIG_ARP_TIMEOUT	200UL

 #endif /* CONFIG_QONG_FPGA */

 #define CONFIG_CONS_INDEX	1
 #define CONFIG_BAUDRATE		115200

 /***********************************************************
  * Command definition
  ***********************************************************/

 #include <config_cmd_default.h>

 #define CONFIG_CMD_CACHE
 #define CONFIG_CMD_DATE
 #define CONFIG_CMD_DHCP
 #define CONFIG_CMD_MII
 #define CONFIG_CMD_NAND
 #define CONFIG_CMD_NET
 #define CONFIG_CMD_PING
 #define CONFIG_CMD_SETEXPR
 #define CONFIG_CMD_SPI
 #define CONFIG_CMD_UNZIP

 #define CONFIG_BOARD_LATE_INIT

 #define CONFIG_BOOTDELAY	5

 #define CONFIG_LOADADDR		0x80800000	/* loadaddr env var */

 #define	CONFIG_EXTRA_ENV_SETTINGS					\
 	"netdev=eth0\0"							\
 	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
 		"nfsroot=${serverip}:${rootpath}\0"			\
 	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
 	"addip=setenv bootargs ${bootargs} "				\
 		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
 		":${hostname}:${netdev}:off panic=1\0"			\
 	"addtty=setenv bootargs ${bootargs}"				\
 		" console=ttymxc0,${baudrate}\0"			\
 	"addmtd=setenv bootargs ${bootargs} ${mtdparts}\0"		\
 	"addmisc=setenv bootargs ${bootargs}\0"				\
 	"uboot_addr=A0000000\0"						\
 	"kernel_addr=A00C0000\0"					\
 	"ramdisk_addr=A0300000\0"					\
 	"u-boot=qong/u-boot.bin\0"					\
 	"kernel_addr_r=80800000\0"					\
 	"hostname=qong\0"						\
 	"bootfile=qong/uImage\0"					\
 	"rootpath=/opt/eldk-4.2-arm/armVFP\0"				\
 	"flash_self=run ramargs addip addtty addmtd addmisc;"		\
 		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
 	"flash_nfs=run nfsargs addip addtty addmtd addmisc;"		\
 		"bootm ${kernel_addr}\0"				\
 	"net_nfs=tftp ${kernel_addr_r} ${bootfile};"			\
 		"run nfsargs addip addtty addmtd addmisc;"		\
 		"bootm\0"						\
 	"bootcmd=run flash_self\0"					\
 	"load=tftp ${loadaddr} ${u-boot}\0"				\
 	"update=protect off " __stringify(CONFIG_SYS_MONITOR_BASE)	\
 		" +${filesize};era " __stringify(CONFIG_SYS_MONITOR_BASE)\
 		" +${filesize};cp.b ${fileaddr} "			\
 		__stringify(CONFIG_SYS_MONITOR_BASE) " ${filesize}\0"	\
 	"upd=run load update\0"						\
 	"videomode=video=ctfb:x:640,y:480,depth:16,mode:0,pclk:40000,"	\
 		"le:120,ri:40,up:35,lo:10,hs:30,vs:3,sync:100663296,"	\
 		"vmode:0\0"						\

 /*
  * Miscellaneous configurable options
  */
 #define CONFIG_SYS_LONGHELP		/* undef to save memory */
 #define CONFIG_SYS_CBSIZE		512	/* Console I/O Buffer Size */
 /* Print Buffer Size */
 #define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + \
 		sizeof(CONFIG_SYS_PROMPT) + 16)
 #define CONFIG_SYS_MAXARGS		32	/* max number of command args */
 /* Boot Argument Buffer Size */
 #define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE

 /* memtest works on first 255MB of RAM */
 #define CONFIG_SYS_MEMTEST_START	PHYS_SDRAM_1
 #define CONFIG_SYS_MEMTEST_END		(PHYS_SDRAM_1 + 0xff000000)

 #define CONFIG_SYS_LOAD_ADDR		CONFIG_LOADADDR

 #define CONFIG_CMDLINE_EDITING
 #define CONFIG_SYS_HUSH_PARSER			/* Use the HUSH parser */

 #define CONFIG_MISC_INIT_R

 /*-----------------------------------------------------------------------
  * Physical Memory Map
  */
 #define CONFIG_NR_DRAM_BANKS	1
 #define PHYS_SDRAM_1		CSD0_BASE
 #define PHYS_SDRAM_1_SIZE	0x10000000	/* 256 MB */

 /*
  * NAND driver
  */

 #ifndef __ASSEMBLY__
 extern void qong_nand_plat_init(void *chip);
 extern int qong_nand_rdy(void *chip);
 #endif
 #define CONFIG_NAND_PLAT
 #define CONFIG_SYS_MAX_NAND_DEVICE     1
 #define CONFIG_SYS_NAND_BASE	CS3_BASE
 #define NAND_PLAT_INIT() qong_nand_plat_init(nand)

 #define QONG_NAND_CLE(chip) ((unsigned long)(chip)->IO_ADDR_W | (1 << 24))
 #define QONG_NAND_ALE(chip) ((unsigned long)(chip)->IO_ADDR_W | (1 << 23))
 #define QONG_NAND_WRITE(addr, cmd) \
 	do { \
 		__REG8(addr) = cmd; \
 	} while (0)

 #define NAND_PLAT_WRITE_CMD(chip, cmd) QONG_NAND_WRITE(QONG_NAND_CLE(chip), cmd)
 #define NAND_PLAT_WRITE_ADR(chip, cmd) QONG_NAND_WRITE(QONG_NAND_ALE(chip), cmd)
 #define NAND_PLAT_DEV_READY(chip)      (qong_nand_rdy(chip))

 /*-----------------------------------------------------------------------
  * FLASH and environment organization
  */
 #define CONFIG_SYS_FLASH_BASE		CS0_BASE
 #define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks */
 /* max number of sectors on one chip */
 #define CONFIG_SYS_MAX_FLASH_SECT	1024
 /* Monitor at beginning of flash */
 #define CONFIG_SYS_MONITOR_BASE		CONFIG_SYS_FLASH_BASE
 #define CONFIG_SYS_MONITOR_LEN		0x40000		/* Reserve 256KiB */

 #define	CONFIG_ENV_IS_IN_FLASH
 #define CONFIG_ENV_SECT_SIZE	0x20000
 #define CONFIG_ENV_SIZE		CONFIG_ENV_SECT_SIZE
 #define CONFIG_ENV_ADDR		(CONFIG_SYS_FLASH_BASE + 0x80000)

 /* Address and size of Redundant Environment Sector	*/
 #define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
 #define CONFIG_ENV_SIZE_REDUND	CONFIG_ENV_SIZE

 /*-----------------------------------------------------------------------
  * CFI FLASH driver setup
  */
 /* Flash memory is CFI compliant */
 #define CONFIG_SYS_FLASH_CFI
 /* Use drivers/cfi_flash.c */
 #define CONFIG_FLASH_CFI_DRIVER
 /* Use buffered writes (~10x faster) */
 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
 /* Use hardware sector protection */
 #define CONFIG_SYS_FLASH_PROTECTION

 /*
  * Filesystem
  */
 #define CONFIG_CMD_JFFS2
 #define CONFIG_CMD_UBI
 #define CONFIG_CMD_UBIFS
 #define CONFIG_RBTREE
 #define CONFIG_MTD_PARTITIONS
 #define CONFIG_CMD_MTDPARTS
 #define CONFIG_LZO
 #define CONFIG_MTD_DEVICE		/* needed for mtdparts commands */
 #define CONFIG_FLASH_CFI_MTD
 #define MTDIDS_DEFAULT		"nor0=physmap-flash.0,"		\
 				"nand0=gen_nand"
 #define MTDPARTS_DEFAULT	\
 	"mtdparts=physmap-flash.0:"				\
 			"512k(U-Boot),128k(env1),128k(env2),"	\
 			"2304k(kernel),13m(ramdisk),-(user);"	\
 		"gen_nand:"					\
 			"128m(nand)"

 /* additions for new relocation code, must be added to all boards */
 #define CONFIG_SYS_SDRAM_BASE		0x80000000
 #define CONFIG_SYS_INIT_RAM_ADDR	IRAM_BASE_ADDR
 #define CONFIG_SYS_INIT_RAM_SIZE		IRAM_SIZE
 #define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_GBL_DATA_OFFSET)

 #define CONFIG_BOARD_EARLY_INIT_F

 #endif /* __CONFIG_H */
	/*
	* Copyright (C) 2009, Ilya Yanok, Emcraft Systems, <yanok@emcraft.com>
	*
	* Configuration settings for the Dave/DENX QongEVB-LITE board.
	*
	* SPDX-License-Identifier: GPL-2.0+
	*/

	#ifndef __CONFIG_H
	#define __CONFIG_H

	#include <asm/arch/imx-regs.h>

	/* High Level Configuration Options */
	#define CONFIG_MX31 /* This is a mx31 */
	#define CONFIG_QONG

	#define CONFIG_DISPLAY_CPUINFO
	#define CONFIG_DISPLAY_BOARDINFO

	#define CONFIG_SYS_TEXT_BASE 0xa0000000

	#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
	#define CONFIG_SETUP_MEMORY_TAGS
	#define CONFIG_INITRD_TAG

	/*
	* Size of malloc() pool
	*/
	#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 1536 * 1024)

	/*
	* Hardware drivers
	*/

	#define CONFIG_MXC_UART
	#define CONFIG_MXC_UART_BASE UART1_BASE

	#define CONFIG_MXC_GPIO
	#define CONFIG_HW_WATCHDOG
	#define CONFIG_IMX_WATCHDOG

	#define CONFIG_MXC_SPI
	#define CONFIG_DEFAULT_SPI_BUS 1
	#define CONFIG_DEFAULT_SPI_MODE (SPI_MODE_0 \| SPI_CS_HIGH)
	#define CONFIG_RTC_MC13XXX

	#define CONFIG_POWER
	#define CONFIG_POWER_SPI
	#define CONFIG_POWER_FSL
	#define CONFIG_FSL_PMIC_BUS 1
	#define CONFIG_FSL_PMIC_CS 0
	#define CONFIG_FSL_PMIC_CLK 100000
	#define CONFIG_FSL_PMIC_MODE (SPI_MODE_0 \| SPI_CS_HIGH)
	#define CONFIG_FSL_PMIC_BITLEN 32

	/* FPGA */
	#define CONFIG_FPGA
	#define CONFIG_QONG_FPGA
	#define CONFIG_FPGA_BASE (CS1_BASE)
	#define CONFIG_FPGA_LATTICE
	#define CONFIG_FPGA_COUNT 1

	#ifdef CONFIG_QONG_FPGA
	/* Ethernet */
	#define CONFIG_DNET
	#define CONFIG_DNET_BASE (CS1_BASE + QONG_FPGA_PERIPH_SIZE)

	/* Framebuffer and LCD */
	#define CONFIG_VIDEO
	#define CONFIG_CFB_CONSOLE
	#define CONFIG_VIDEO_MX3
	#define CONFIG_VIDEO_LOGO
	#define CONFIG_VIDEO_SW_CURSOR
	#define CONFIG_VGA_AS_SINGLE_DEVICE
	#define CONFIG_SYS_CONSOLE_IS_IN_ENV
	#define CONFIG_SPLASH_SCREEN
	#define CONFIG_CMD_BMP
	#define CONFIG_BMP_16BPP
	#define CONFIG_VIDEO_BMP_GZIP
	#define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE (512 << 10)

	/* USB */
	#define CONFIG_CMD_USB
	#ifdef CONFIG_CMD_USB
	#define CONFIG_USB_EHCI /* Enable EHCI USB support */
	#define CONFIG_USB_EHCI_MXC
	#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
	#define CONFIG_MXC_USB_PORT 2
	#define CONFIG_MXC_USB_PORTSC (MXC_EHCI_MODE_ULPI \| MXC_EHCI_UTMI_8BIT)
	#define CONFIG_MXC_USB_FLAGS MXC_EHCI_POWER_PINS_ENABLED
	#define CONFIG_EHCI_IS_TDI
	#define CONFIG_USB_STORAGE
	#define CONFIG_DOS_PARTITION
	#define CONFIG_SUPPORT_VFAT
	#define CONFIG_CMD_EXT2
	#define CONFIG_CMD_FAT
	#endif /* CONFIG_CMD_USB */

	/*
	* Reducing the ARP timeout from default 5 seconds to 200ms we speed up the
	* initial TFTP transfer, should the user wish one, significantly.
	*/
	#define CONFIG_ARP_TIMEOUT 200UL

	#endif /* CONFIG_QONG_FPGA */

	#define CONFIG_CONS_INDEX 1
	#define CONFIG_BAUDRATE 115200

	/***********************************************************
	* Command definition
	***********************************************************/

	#include <config_cmd_default.h>

	#define CONFIG_CMD_CACHE
	#define CONFIG_CMD_DATE
	#define CONFIG_CMD_DHCP
	#define CONFIG_CMD_MII
	#define CONFIG_CMD_NAND
	#define CONFIG_CMD_NET
	#define CONFIG_CMD_PING
	#define CONFIG_CMD_SETEXPR
	#define CONFIG_CMD_SPI
	#define CONFIG_CMD_UNZIP

	#define CONFIG_BOARD_LATE_INIT

	#define CONFIG_BOOTDELAY 5

	#define CONFIG_LOADADDR 0x80800000 /* loadaddr env var */

	#define CONFIG_EXTRA_ENV_SETTINGS \
	"netdev=eth0\0" \
	"nfsargs=setenv bootargs root=/dev/nfs rw " \
	"nfsroot=${serverip}:${rootpath}\0" \
	"ramargs=setenv bootargs root=/dev/ram rw\0" \
	"addip=setenv bootargs ${bootargs} " \
	"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
	":${hostname}:${netdev}:off panic=1\0" \
	"addtty=setenv bootargs ${bootargs}" \
	" console=ttymxc0,${baudrate}\0" \
	"addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \
	"addmisc=setenv bootargs ${bootargs}\0" \
	"uboot_addr=A0000000\0" \
	"kernel_addr=A00C0000\0" \
	"ramdisk_addr=A0300000\0" \
	"u-boot=qong/u-boot.bin\0" \
	"kernel_addr_r=80800000\0" \
	"hostname=qong\0" \
	"bootfile=qong/uImage\0" \
	"rootpath=/opt/eldk-4.2-arm/armVFP\0" \
	"flash_self=run ramargs addip addtty addmtd addmisc;" \
	"bootm ${kernel_addr} ${ramdisk_addr}\0" \
	"flash_nfs=run nfsargs addip addtty addmtd addmisc;" \
	"bootm ${kernel_addr}\0" \
	"net_nfs=tftp ${kernel_addr_r} ${bootfile};" \
	"run nfsargs addip addtty addmtd addmisc;" \
	"bootm\0" \
	"bootcmd=run flash_self\0" \
	"load=tftp ${loadaddr} ${u-boot}\0" \
	"update=protect off " __stringify(CONFIG_SYS_MONITOR_BASE) \
	" +${filesize};era " __stringify(CONFIG_SYS_MONITOR_BASE)\
	" +${filesize};cp.b ${fileaddr} " \
	__stringify(CONFIG_SYS_MONITOR_BASE) " ${filesize}\0" \
	"upd=run load update\0" \
	"videomode=video=ctfb:x:640,y:480,depth:16,mode:0,pclk:40000," \
	"le:120,ri:40,up:35,lo:10,hs:30,vs:3,sync:100663296," \
	"vmode:0\0" \

	/*
	* Miscellaneous configurable options
	*/
	#define CONFIG_SYS_LONGHELP /* undef to save memory */
	#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
	/* Print Buffer Size */
	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
	sizeof(CONFIG_SYS_PROMPT) + 16)
	#define CONFIG_SYS_MAXARGS 32 /* max number of command args */
	/* Boot Argument Buffer Size */
	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE

	/* memtest works on first 255MB of RAM */
	#define CONFIG_SYS_MEMTEST_START PHYS_SDRAM_1
	#define CONFIG_SYS_MEMTEST_END (PHYS_SDRAM_1 + 0xff000000)

	#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR

	#define CONFIG_CMDLINE_EDITING
	#define CONFIG_SYS_HUSH_PARSER /* Use the HUSH parser */

	#define CONFIG_MISC_INIT_R

	/*-----------------------------------------------------------------------
	* Physical Memory Map
	*/
	#define CONFIG_NR_DRAM_BANKS 1
	#define PHYS_SDRAM_1 CSD0_BASE
	#define PHYS_SDRAM_1_SIZE 0x10000000 /* 256 MB */

	/*
	* NAND driver
	*/

	#ifndef __ASSEMBLY__
	extern void qong_nand_plat_init(void *chip);
	extern int qong_nand_rdy(void *chip);
	#endif
	#define CONFIG_NAND_PLAT
	#define CONFIG_SYS_MAX_NAND_DEVICE 1
	#define CONFIG_SYS_NAND_BASE CS3_BASE
	#define NAND_PLAT_INIT() qong_nand_plat_init(nand)

	#define QONG_NAND_CLE(chip) ((unsigned long)(chip)->IO_ADDR_W \| (1 << 24))
	#define QONG_NAND_ALE(chip) ((unsigned long)(chip)->IO_ADDR_W \| (1 << 23))
	#define QONG_NAND_WRITE(addr, cmd) \
	do { \
	__REG8(addr) = cmd; \
	} while (0)

	#define NAND_PLAT_WRITE_CMD(chip, cmd) QONG_NAND_WRITE(QONG_NAND_CLE(chip), cmd)
	#define NAND_PLAT_WRITE_ADR(chip, cmd) QONG_NAND_WRITE(QONG_NAND_ALE(chip), cmd)
	#define NAND_PLAT_DEV_READY(chip) (qong_nand_rdy(chip))

	/*-----------------------------------------------------------------------
	* FLASH and environment organization
	*/
	#define CONFIG_SYS_FLASH_BASE CS0_BASE
	#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
	/* max number of sectors on one chip */
	#define CONFIG_SYS_MAX_FLASH_SECT 1024
	/* Monitor at beginning of flash */
	#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
	#define CONFIG_SYS_MONITOR_LEN 0x40000 /* Reserve 256KiB */

	#define CONFIG_ENV_IS_IN_FLASH
	#define CONFIG_ENV_SECT_SIZE 0x20000
	#define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE
	#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x80000)

	/* Address and size of Redundant Environment Sector */
	#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
	#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE

	/*-----------------------------------------------------------------------
	* CFI FLASH driver setup
	*/
	/* Flash memory is CFI compliant */
	#define CONFIG_SYS_FLASH_CFI
	/* Use drivers/cfi_flash.c */
	#define CONFIG_FLASH_CFI_DRIVER
	/* Use buffered writes (~10x faster) */
	#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
	/* Use hardware sector protection */
	#define CONFIG_SYS_FLASH_PROTECTION

	/*
	* Filesystem
	*/
	#define CONFIG_CMD_JFFS2
	#define CONFIG_CMD_UBI
	#define CONFIG_CMD_UBIFS
	#define CONFIG_RBTREE
	#define CONFIG_MTD_PARTITIONS
	#define CONFIG_CMD_MTDPARTS
	#define CONFIG_LZO
	#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
	#define CONFIG_FLASH_CFI_MTD
	#define MTDIDS_DEFAULT "nor0=physmap-flash.0," \
	"nand0=gen_nand"
	#define MTDPARTS_DEFAULT \
	"mtdparts=physmap-flash.0:" \
	"512k(U-Boot),128k(env1),128k(env2)," \
	"2304k(kernel),13m(ramdisk),-(user);" \
	"gen_nand:" \
	"128m(nand)"

	/* additions for new relocation code, must be added to all boards */
	#define CONFIG_SYS_SDRAM_BASE 0x80000000
	#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
	#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
	#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
	#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_GBL_DATA_OFFSET)

	#define CONFIG_BOARD_EARLY_INIT_F

	#endif /* __CONFIG_H */