| /* |
| * (C) Copyright 2006-2008 |
| * Texas Instruments. |
| * Richard Woodruff <r-woodruff2@ti.com> |
| * Syed Mohammed Khasim <x0khasim@ti.com> |
| * |
| * (C) Copyright 2009 |
| * Frederik Kriewitz <frederik@kriewitz.eu> |
| * |
| * Configuration settings for the DevKit8000 board. |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| /* High Level Configuration Options */ |
| #define CONFIG_OMAP 1 /* in a TI OMAP core */ |
| #define CONFIG_OMAP3_DEVKIT8000 1 /* working with DevKit8000 */ |
| #define CONFIG_MACH_TYPE MACH_TYPE_DEVKIT8000 |
| #define CONFIG_OMAP_GPIO |
| #define CONFIG_OMAP_COMMON |
| |
| /* |
| * 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM |
| * 64 bytes before this address should be set aside for u-boot.img's |
| * header. That is 0x800FFFC0--0x80100000 should not be used for any |
| * other needs. |
| */ |
| #define CONFIG_SYS_TEXT_BASE 0x80100000 |
| |
| #define CONFIG_SDRC /* The chip has SDRC controller */ |
| |
| #include <asm/arch/cpu.h> /* get chip and board defs */ |
| #include <asm/arch/omap3.h> |
| |
| /* Display CPU and Board information */ |
| #define CONFIG_DISPLAY_CPUINFO 1 |
| #define CONFIG_DISPLAY_BOARDINFO 1 |
| |
| /* Clock Defines */ |
| #define V_OSCK 26000000 /* Clock output from T2 */ |
| #define V_SCLK (V_OSCK >> 1) |
| |
| #define CONFIG_MISC_INIT_R |
| |
| #define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ |
| #define CONFIG_SETUP_MEMORY_TAGS 1 |
| #define CONFIG_INITRD_TAG 1 |
| #define CONFIG_REVISION_TAG 1 |
| |
| #define CONFIG_OF_LIBFDT 1 |
| |
| /* Size of malloc() pool */ |
| #define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB */ |
| /* Sector */ |
| #define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128 << 10)) |
| |
| /* Hardware drivers */ |
| /* DM9000 */ |
| #define CONFIG_NET_RETRY_COUNT 20 |
| #define CONFIG_DRIVER_DM9000 1 |
| #define CONFIG_DM9000_BASE 0x2c000000 |
| #define DM9000_IO CONFIG_DM9000_BASE |
| #define DM9000_DATA (CONFIG_DM9000_BASE + 0x400) |
| #define CONFIG_DM9000_USE_16BIT 1 |
| #define CONFIG_DM9000_NO_SROM 1 |
| #undef CONFIG_DM9000_DEBUG |
| |
| /* NS16550 Configuration */ |
| #define CONFIG_SYS_NS16550 |
| #define CONFIG_SYS_NS16550_SERIAL |
| #define CONFIG_SYS_NS16550_REG_SIZE (-4) |
| #define CONFIG_SYS_NS16550_CLK 48000000 /* 48MHz (APLL96/2) */ |
| |
| /* select serial console configuration */ |
| #define CONFIG_CONS_INDEX 3 |
| #define CONFIG_SYS_NS16550_COM3 OMAP34XX_UART3 |
| #define CONFIG_SERIAL3 3 |
| #define CONFIG_BAUDRATE 115200 |
| #define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600,\ |
| 115200} |
| |
| /* MMC */ |
| #define CONFIG_GENERIC_MMC 1 |
| #define CONFIG_MMC 1 |
| #define CONFIG_OMAP_HSMMC 1 |
| #define CONFIG_DOS_PARTITION 1 |
| |
| /* I2C */ |
| #define CONFIG_SYS_I2C |
| #define CONFIG_SYS_OMAP24_I2C_SPEED 100000 |
| #define CONFIG_SYS_OMAP24_I2C_SLAVE 1 |
| #define CONFIG_SYS_I2C_OMAP34XX |
| |
| /* TWL4030 */ |
| #define CONFIG_TWL4030_POWER 1 |
| #define CONFIG_TWL4030_LED 1 |
| |
| /* Board NAND Info */ |
| #define CONFIG_SYS_NO_FLASH /* no NOR flash */ |
| #define CONFIG_MTD_DEVICE /* needed for mtdparts commands */ |
| #define MTDIDS_DEFAULT "nand0=nand" |
| #define MTDPARTS_DEFAULT "mtdparts=nand:" \ |
| "512k(x-loader)," \ |
| "1920k(u-boot)," \ |
| "128k(u-boot-env)," \ |
| "4m(kernel)," \ |
| "-(fs)" |
| |
| #define CONFIG_NAND_OMAP_GPMC |
| #define CONFIG_SYS_NAND_ADDR NAND_BASE /* physical address */ |
| /* to access nand */ |
| #define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */ |
| /* to access nand at */ |
| /* CS0 */ |
| #define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */ |
| /* devices */ |
| #define CONFIG_JFFS2_NAND |
| /* nand device jffs2 lives on */ |
| #define CONFIG_JFFS2_DEV "nand0" |
| /* start of jffs2 partition */ |
| #define CONFIG_JFFS2_PART_OFFSET 0x680000 |
| #define CONFIG_JFFS2_PART_SIZE 0xf980000 /* size of jffs2 */ |
| /* partition */ |
| |
| /* commands to include */ |
| #include <config_cmd_default.h> |
| |
| #define CONFIG_CMD_DHCP /* DHCP support */ |
| #define CONFIG_CMD_EXT2 /* EXT2 Support */ |
| #define CONFIG_CMD_FAT /* FAT support */ |
| #define CONFIG_CMD_I2C /* I2C serial bus support */ |
| #define CONFIG_CMD_JFFS2 /* JFFS2 Support */ |
| #define CONFIG_CMD_MMC /* MMC support */ |
| #define CONFIG_CMD_MTDPARTS /* Enable MTD parts commands */ |
| #define CONFIG_CMD_NAND /* NAND support */ |
| #define CONFIG_CMD_NAND_LOCK_UNLOCK /* nand (un)lock commands */ |
| |
| #undef CONFIG_CMD_FPGA /* FPGA configuration Support */ |
| #undef CONFIG_CMD_IMI /* iminfo */ |
| |
| /* BOOTP/DHCP options */ |
| #define CONFIG_BOOTP_SUBNETMASK |
| #define CONFIG_BOOTP_GATEWAY |
| #define CONFIG_BOOTP_HOSTNAME |
| #define CONFIG_BOOTP_NISDOMAIN |
| #define CONFIG_BOOTP_BOOTPATH |
| #define CONFIG_BOOTP_BOOTFILESIZE |
| #define CONFIG_BOOTP_DNS |
| #define CONFIG_BOOTP_DNS2 |
| #define CONFIG_BOOTP_SEND_HOSTNAME |
| #define CONFIG_BOOTP_NTPSERVER |
| #define CONFIG_BOOTP_TIMEOFFSET |
| #undef CONFIG_BOOTP_VENDOREX |
| |
| /* Environment information */ |
| #define CONFIG_ENV_OVERWRITE /* allow to overwrite serial and ethaddr */ |
| |
| #define CONFIG_BOOTDELAY 3 |
| |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| "loadaddr=0x82000000\0" \ |
| "console=ttyO2,115200n8\0" \ |
| "mmcdev=0\0" \ |
| "vram=12M\0" \ |
| "dvimode=1024x768MR-16@60\0" \ |
| "defaultdisplay=dvi\0" \ |
| "nfsopts=hard,tcp,rsize=65536,wsize=65536\0" \ |
| "kernelopts=rw\0" \ |
| "commonargs=" \ |
| "setenv bootargs console=${console} " \ |
| "vram=${vram} " \ |
| "omapfb.mode=dvi:${dvimode} " \ |
| "omapdss.def_disp=${defaultdisplay}\0" \ |
| "mmcargs=" \ |
| "run commonargs; " \ |
| "setenv bootargs ${bootargs} " \ |
| "root=/dev/mmcblk0p2 " \ |
| "rootwait " \ |
| "${kernelopts}\0" \ |
| "nandargs=" \ |
| "run commonargs; " \ |
| "setenv bootargs ${bootargs} " \ |
| "omapfb.mode=dvi:${dvimode} " \ |
| "omapdss.def_disp=${defaultdisplay} " \ |
| "root=/dev/mtdblock4 " \ |
| "rootfstype=jffs2 " \ |
| "${kernelopts}\0" \ |
| "netargs=" \ |
| "run commonargs; " \ |
| "setenv bootargs ${bootargs} " \ |
| "root=/dev/nfs " \ |
| "nfsroot=${serverip}:${rootpath},${nfsopts} " \ |
| "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off " \ |
| "${kernelopts} " \ |
| "dnsip1=${dnsip} " \ |
| "dnsip2=${dnsip2}\0" \ |
| "loadbootscript=fatload mmc ${mmcdev} ${loadaddr} boot.scr\0" \ |
| "bootscript=echo Running bootscript from mmc ...; " \ |
| "source ${loadaddr}\0" \ |
| "loaduimage=fatload mmc ${mmcdev} ${loadaddr} uImage\0" \ |
| "eraseenv=nand unlock 0x260000 0x20000; nand erase 0x260000 0x20000\0" \ |
| "mmcboot=echo Booting from mmc ...; " \ |
| "run mmcargs; " \ |
| "bootm ${loadaddr}\0" \ |
| "nandboot=echo Booting from nand ...; " \ |
| "run nandargs; " \ |
| "nand read ${loadaddr} 280000 400000; " \ |
| "bootm ${loadaddr}\0" \ |
| "netboot=echo Booting from network ...; " \ |
| "dhcp ${loadaddr}; " \ |
| "run netargs; " \ |
| "bootm ${loadaddr}\0" \ |
| "autoboot=mmc dev ${mmcdev}; if mmc rescan; then " \ |
| "if run loadbootscript; then " \ |
| "run bootscript; " \ |
| "else " \ |
| "if run loaduimage; then " \ |
| "run mmcboot; " \ |
| "else run nandboot; " \ |
| "fi; " \ |
| "fi; " \ |
| "else run nandboot; fi\0" |
| |
| |
| #define CONFIG_BOOTCOMMAND "run autoboot" |
| |
| /* Miscellaneous configurable options */ |
| #define CONFIG_SYS_LONGHELP /* undef to save memory */ |
| #define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */ |
| #define CONFIG_AUTO_COMPLETE 1 |
| #define CONFIG_SYS_PROMPT "OMAP3 DevKit8000 # " |
| #define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */ |
| /* Print Buffer Size */ |
| #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ |
| sizeof(CONFIG_SYS_PROMPT) + 16) |
| #define CONFIG_SYS_MAXARGS 128 /* max number of command args */ |
| |
| /* Boot Argument Buffer Size */ |
| #define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE) |
| |
| #define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0 + 0x07000000) |
| #define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + \ |
| 0x01000000) /* 16MB */ |
| |
| #define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0 + 0x02000000) |
| |
| /* |
| * OMAP3 has 12 GP timers, they can be driven by the system clock |
| * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK). |
| * This rate is divided by a local divisor. |
| */ |
| #define CONFIG_SYS_TIMERBASE (OMAP34XX_GPT2) |
| #define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */ |
| |
| /* Physical Memory Map */ |
| #define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */ |
| #define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0 |
| #define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1 |
| |
| /* NAND and environment organization */ |
| #define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 2 sectors */ |
| |
| #define CONFIG_ENV_IS_IN_NAND 1 |
| #define SMNAND_ENV_OFFSET 0x260000 /* environment starts here */ |
| |
| #define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET |
| |
| #define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 |
| #define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800 |
| #define CONFIG_SYS_INIT_RAM_SIZE 0x800 |
| #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \ |
| CONFIG_SYS_INIT_RAM_SIZE - \ |
| GENERATED_GBL_DATA_SIZE) |
| |
| /* SRAM config */ |
| #define CONFIG_SYS_SRAM_START 0x40200000 |
| #define CONFIG_SYS_SRAM_SIZE 0x10000 |
| |
| /* Defines for SPL */ |
| #define CONFIG_SPL_FRAMEWORK |
| #define CONFIG_SPL_NAND_SIMPLE |
| |
| #define CONFIG_SPL_LIBCOMMON_SUPPORT |
| #define CONFIG_SPL_LIBDISK_SUPPORT |
| #define CONFIG_SPL_BOARD_INIT |
| #define CONFIG_SPL_I2C_SUPPORT |
| #define CONFIG_SPL_LIBGENERIC_SUPPORT |
| #define CONFIG_SPL_SERIAL_SUPPORT |
| #define CONFIG_SPL_GPIO_SUPPORT |
| #define CONFIG_SPL_POWER_SUPPORT |
| #define CONFIG_SPL_NAND_SUPPORT |
| #define CONFIG_SPL_NAND_BASE |
| #define CONFIG_SPL_NAND_DRIVERS |
| #define CONFIG_SPL_NAND_ECC |
| #define CONFIG_SPL_MMC_SUPPORT |
| #define CONFIG_SPL_FAT_SUPPORT |
| #define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/omap-common/u-boot-spl.lds" |
| #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img" |
| #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1 |
| #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /* address 0x60000 */ |
| |
| #define CONFIG_SPL_TEXT_BASE 0x40200000 /*CONFIG_SYS_SRAM_START*/ |
| #define CONFIG_SPL_MAX_SIZE (54 * 1024) /* 8 KB for stack */ |
| #define CONFIG_SPL_STACK LOW_LEVEL_SRAM_STACK |
| |
| #define CONFIG_SPL_BSS_START_ADDR 0x80000500 /* leave space for bootargs*/ |
| #define CONFIG_SPL_BSS_MAX_SIZE 0x80000 |
| |
| /* NAND boot config */ |
| #define CONFIG_SYS_NAND_BUSWIDTH_16BIT 16 |
| #define CONFIG_SYS_NAND_5_ADDR_CYCLE |
| #define CONFIG_SYS_NAND_PAGE_COUNT 64 |
| #define CONFIG_SYS_NAND_PAGE_SIZE 2048 |
| #define CONFIG_SYS_NAND_OOBSIZE 64 |
| #define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024) |
| #define CONFIG_SYS_NAND_BAD_BLOCK_POS 0 |
| #define CONFIG_SYS_NAND_ECCPOS {2, 3, 4, 5, 6, 7, 8, 9,\ |
| 10, 11, 12, 13} |
| |
| #define CONFIG_SYS_NAND_ECCSIZE 512 |
| #define CONFIG_SYS_NAND_ECCBYTES 3 |
| #define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_HAM1_CODE_HW |
| |
| #define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE |
| |
| #define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000 |
| #define CONFIG_SYS_NAND_U_BOOT_SIZE 0x200000 |
| |
| #define CONFIG_SYS_SPL_MALLOC_START 0x80208000 |
| #define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000 /* 1 MB */ |
| |
| /* SPL OS boot options */ |
| #define CONFIG_SPL_OS_BOOT |
| |
| #define CONFIG_CMD_SPL |
| #define CONFIG_CMD_SPL_WRITE_SIZE 0x400 /* 1024 byte */ |
| #define CONFIG_CMD_SPL_NAND_OFS (CONFIG_SYS_NAND_SPL_KERNEL_OFFS+\ |
| 0x400000) |
| #define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x280000 |
| |
| #define CONFIG_SPL_FS_LOAD_KERNEL_NAME "uImage" |
| #define CONFIG_SPL_FS_LOAD_ARGS_NAME "args" |
| |
| #define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0x500 /* address 0xa0000 */ |
| #define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR 0x8 /* address 0x1000 */ |
| #define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS 8 /* 4KB */ |
| |
| #define CONFIG_SYS_SPL_ARGS_ADDR (PHYS_SDRAM_1 + 0x100) |
| |
| #endif /* __CONFIG_H */ |