blob: 45aaf906f71018a0c8cae4936528fc9921895d4a [file] [log] [blame]
/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
#ifndef __CONFIG_H
#define __CONFIG_H
/*
* T104x RDB board configuration file
*/
#include <asm/config_mpc85xx.h>
#ifdef CONFIG_RAMBOOT_PBL
#ifndef CONFIG_SECURE_BOOT
#define CONFIG_SYS_FSL_PBL_PBI $(SRCTREE)/board/freescale/t104xrdb/t104x_pbi.cfg
#else
#define CONFIG_SYS_FSL_PBL_PBI \
$(SRCTREE)/board/freescale/t104xrdb/t104x_pbi_sb.cfg
#endif
#define CONFIG_SPL_FLUSH_IMAGE
#define CONFIG_SPL_TARGET "u-boot-with-spl.bin"
#define CONFIG_SYS_TEXT_BASE 0x30001000
#define CONFIG_SPL_TEXT_BASE 0xFFFD8000
#define CONFIG_SPL_PAD_TO 0x40000
#define CONFIG_SPL_MAX_SIZE 0x28000
#ifdef CONFIG_SPL_BUILD
#define CONFIG_SPL_SKIP_RELOCATE
#define CONFIG_SPL_COMMON_INIT_DDR
#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
#define CONFIG_SYS_NO_FLASH
#endif
#define RESET_VECTOR_OFFSET 0x27FFC
#define BOOT_PAGE_OFFSET 0x27000
#ifdef CONFIG_NAND
#ifdef CONFIG_SECURE_BOOT
#define CONFIG_U_BOOT_HDR_SIZE (16 << 10)
/*
* HDR would be appended at end of image and copied to DDR along
* with U-Boot image.
*/
#define CONFIG_SYS_NAND_U_BOOT_SIZE ((768 << 10) + \
CONFIG_U_BOOT_HDR_SIZE)
#else
#define CONFIG_SYS_NAND_U_BOOT_SIZE (768 << 10)
#endif
#define CONFIG_SYS_NAND_U_BOOT_DST 0x30000000
#define CONFIG_SYS_NAND_U_BOOT_START 0x30000000
#define CONFIG_SYS_NAND_U_BOOT_OFFS (256 << 10)
#define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot-nand.lds"
#ifdef CONFIG_TARGET_T1040RDB
#define CONFIG_SYS_FSL_PBL_RCW \
$(SRCTREE)/board/freescale/t104xrdb/t1040_nand_rcw.cfg
#endif
#ifdef CONFIG_TARGET_T1042RDB_PI
#define CONFIG_SYS_FSL_PBL_RCW \
$(SRCTREE)/board/freescale/t104xrdb/t1042_pi_nand_rcw.cfg
#endif
#ifdef CONFIG_TARGET_T1042RDB
#define CONFIG_SYS_FSL_PBL_RCW \
$(SRCTREE)/board/freescale/t104xrdb/t1042_nand_rcw.cfg
#endif
#ifdef CONFIG_TARGET_T1040D4RDB
#define CONFIG_SYS_FSL_PBL_RCW \
$(SRCTREE)/board/freescale/t104xrdb/t1040d4_nand_rcw.cfg
#endif
#ifdef CONFIG_TARGET_T1042D4RDB
#define CONFIG_SYS_FSL_PBL_RCW \
$(SRCTREE)/board/freescale/t104xrdb/t1042d4_nand_rcw.cfg
#endif
#define CONFIG_SPL_NAND_BOOT
#endif
#ifdef CONFIG_SPIFLASH
#define CONFIG_RESET_VECTOR_ADDRESS 0x30000FFC
#define CONFIG_SPL_SPI_FLASH_MINIMAL
#define CONFIG_SYS_SPI_FLASH_U_BOOT_SIZE (768 << 10)
#define CONFIG_SYS_SPI_FLASH_U_BOOT_DST (0x30000000)
#define CONFIG_SYS_SPI_FLASH_U_BOOT_START (0x30000000)
#define CONFIG_SYS_SPI_FLASH_U_BOOT_OFFS (256 << 10)
#define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot.lds"
#ifndef CONFIG_SPL_BUILD
#define CONFIG_SYS_MPC85XX_NO_RESETVEC
#endif
#ifdef CONFIG_TARGET_T1040RDB
#define CONFIG_SYS_FSL_PBL_RCW \
$(SRCTREE)/board/freescale/t104xrdb/t1040_spi_rcw.cfg
#endif
#ifdef CONFIG_TARGET_T1042RDB_PI
#define CONFIG_SYS_FSL_PBL_RCW \
$(SRCTREE)/board/freescale/t104xrdb/t1042_pi_spi_rcw.cfg
#endif
#ifdef CONFIG_TARGET_T1042RDB
#define CONFIG_SYS_FSL_PBL_RCW \
$(SRCTREE)/board/freescale/t104xrdb/t1042_spi_rcw.cfg
#endif
#ifdef CONFIG_TARGET_T1040D4RDB
#define CONFIG_SYS_FSL_PBL_RCW \
$(SRCTREE)/board/freescale/t104xrdb/t1040d4_spi_rcw.cfg
#endif
#ifdef CONFIG_TARGET_T1042D4RDB
#define CONFIG_SYS_FSL_PBL_RCW \
$(SRCTREE)/board/freescale/t104xrdb/t1042d4_spi_rcw.cfg
#endif
#define CONFIG_SPL_SPI_BOOT
#endif
#ifdef CONFIG_SDCARD
#define CONFIG_RESET_VECTOR_ADDRESS 0x30000FFC
#define CONFIG_SPL_MMC_MINIMAL
#define CONFIG_SYS_MMC_U_BOOT_SIZE (768 << 10)
#define CONFIG_SYS_MMC_U_BOOT_DST (0x30000000)
#define CONFIG_SYS_MMC_U_BOOT_START (0x30000000)
#define CONFIG_SYS_MMC_U_BOOT_OFFS (260 << 10)
#define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot.lds"
#ifndef CONFIG_SPL_BUILD
#define CONFIG_SYS_MPC85XX_NO_RESETVEC
#endif
#ifdef CONFIG_TARGET_T1040RDB
#define CONFIG_SYS_FSL_PBL_RCW \
$(SRCTREE)/board/freescale/t104xrdb/t1040_sd_rcw.cfg
#endif
#ifdef CONFIG_TARGET_T1042RDB_PI
#define CONFIG_SYS_FSL_PBL_RCW \
$(SRCTREE)/board/freescale/t104xrdb/t1042_pi_sd_rcw.cfg
#endif
#ifdef CONFIG_TARGET_T1042RDB
#define CONFIG_SYS_FSL_PBL_RCW \
$(SRCTREE)/board/freescale/t104xrdb/t1042_sd_rcw.cfg
#endif
#ifdef CONFIG_TARGET_T1040D4RDB
#define CONFIG_SYS_FSL_PBL_RCW \
$(SRCTREE)/board/freescale/t104xrdb/t1040d4_sd_rcw.cfg
#endif
#ifdef CONFIG_TARGET_T1042D4RDB
#define CONFIG_SYS_FSL_PBL_RCW \
$(SRCTREE)/board/freescale/t104xrdb/t1042d4_sd_rcw.cfg
#endif
#define CONFIG_SPL_MMC_BOOT
#endif
#endif
/* High Level Configuration Options */
#define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */
#define CONFIG_MP /* support multiple processors */
/* support deep sleep */
#define CONFIG_DEEP_SLEEP
#ifndef CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_TEXT_BASE 0xeff40000
#endif
#ifndef CONFIG_RESET_VECTOR_ADDRESS
#define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc
#endif
#define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */
#define CONFIG_SYS_NUM_CPC CONFIG_SYS_NUM_DDR_CTLRS
#define CONFIG_FSL_IFC /* Enable IFC Support */
#define CONFIG_FSL_CAAM /* Enable SEC/CAAM */
#define CONFIG_PCI_INDIRECT_BRIDGE
#define CONFIG_PCIE1 /* PCIE controller 1 */
#define CONFIG_PCIE2 /* PCIE controller 2 */
#define CONFIG_PCIE3 /* PCIE controller 3 */
#define CONFIG_PCIE4 /* PCIE controller 4 */
#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */
#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */
#define CONFIG_ENV_OVERWRITE
#ifndef CONFIG_SYS_NO_FLASH
#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
#endif
#if defined(CONFIG_SPIFLASH)
#define CONFIG_SYS_EXTRA_ENV_RELOC
#define CONFIG_ENV_IS_IN_SPI_FLASH
#define CONFIG_ENV_SIZE 0x2000 /* 8KB */
#define CONFIG_ENV_OFFSET 0x100000 /* 1MB */
#define CONFIG_ENV_SECT_SIZE 0x10000
#elif defined(CONFIG_SDCARD)
#define CONFIG_SYS_EXTRA_ENV_RELOC
#define CONFIG_ENV_IS_IN_MMC
#define CONFIG_SYS_MMC_ENV_DEV 0
#define CONFIG_ENV_SIZE 0x2000
#define CONFIG_ENV_OFFSET (512 * 0x800)
#elif defined(CONFIG_NAND)
#ifdef CONFIG_SECURE_BOOT
#define CONFIG_RAMBOOT_NAND
#define CONFIG_BOOTSCRIPT_COPY_RAM
#endif
#define CONFIG_SYS_EXTRA_ENV_RELOC
#define CONFIG_ENV_IS_IN_NAND
#define CONFIG_ENV_SIZE 0x2000
#define CONFIG_ENV_OFFSET (3 * CONFIG_SYS_NAND_BLOCK_SIZE)
#else
#define CONFIG_ENV_IS_IN_FLASH
#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE 0x2000
#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */
#endif
#define CONFIG_SYS_CLK_FREQ 100000000
#define CONFIG_DDR_CLK_FREQ 66666666
/*
* These can be toggled for performance analysis, otherwise use default.
*/
#define CONFIG_SYS_CACHE_STASHING
#define CONFIG_BACKSIDE_L2_CACHE
#define CONFIG_SYS_INIT_L2CSR0 L2CSR0_L2E
#define CONFIG_BTB /* toggle branch predition */
#define CONFIG_DDR_ECC
#ifdef CONFIG_DDR_ECC
#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
#endif
#define CONFIG_ENABLE_36BIT_PHYS
#define CONFIG_ADDR_MAP
#define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */
#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x00400000
#define CONFIG_SYS_ALT_MEMTEST
#define CONFIG_PANIC_HANG /* do not reset board on panic */
/*
* Config the L3 Cache as L3 SRAM
*/
#define CONFIG_SYS_INIT_L3_ADDR 0xFFFC0000
/*
* For Secure Boot CONFIG_SYS_INIT_L3_ADDR will be redefined and hence
* Physical address (CONFIG_SYS_INIT_L3_ADDR) and virtual address
* (CONFIG_SYS_INIT_L3_VADDR) will be different.
*/
#define CONFIG_SYS_INIT_L3_VADDR 0xFFFC0000
#define CONFIG_SYS_L3_SIZE 256 << 10
#define CONFIG_SPL_GD_ADDR (CONFIG_SYS_INIT_L3_VADDR + 32 * 1024)
#ifdef CONFIG_RAMBOOT_PBL
#define CONFIG_ENV_ADDR (CONFIG_SPL_GD_ADDR + 4 * 1024)
#endif
#define CONFIG_SPL_RELOC_MALLOC_ADDR (CONFIG_SPL_GD_ADDR + 12 * 1024)
#define CONFIG_SPL_RELOC_MALLOC_SIZE (30 << 10)
#define CONFIG_SPL_RELOC_STACK (CONFIG_SPL_GD_ADDR + 64 * 1024)
#define CONFIG_SPL_RELOC_STACK_SIZE (22 << 10)
#define CONFIG_SYS_DCSRBAR 0xf0000000
#define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull
/*
* DDR Setup
*/
#define CONFIG_VERY_BIG_RAM
#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
#define CONFIG_DIMM_SLOTS_PER_CTLR 1
#define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR)
#define CONFIG_DDR_SPD
#define CONFIG_SYS_SPD_BUS_NUM 0
#define SPD_EEPROM_ADDRESS 0x51
#define CONFIG_SYS_SDRAM_SIZE 4096 /* for fixed parameter use */
/*
* IFC Definitions
*/
#define CONFIG_SYS_FLASH_BASE 0xe8000000
#define CONFIG_SYS_FLASH_BASE_PHYS (0xf00000000ull | CONFIG_SYS_FLASH_BASE)
#define CONFIG_SYS_NOR_CSPR_EXT (0xf)
#define CONFIG_SYS_NOR_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE) | \
CSPR_PORT_SIZE_16 | \
CSPR_MSEL_NOR | \
CSPR_V)
#define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024)
/*
* TDM Definition
*/
#define T1040_TDM_QUIRK_CCSR_BASE 0xfe000000
/* NOR Flash Timing Params */
#define CONFIG_SYS_NOR_CSOR CSOR_NAND_TRHZ_80
#define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \
FTIM0_NOR_TEADC(0x5) | \
FTIM0_NOR_TEAHC(0x5))
#define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \
FTIM1_NOR_TRAD_NOR(0x1A) |\
FTIM1_NOR_TSEQRAD_NOR(0x13))
#define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \
FTIM2_NOR_TCH(0x4) | \
FTIM2_NOR_TWPH(0x0E) | \
FTIM2_NOR_TWP(0x1c))
#define CONFIG_SYS_NOR_FTIM3 0x0
#define CONFIG_SYS_FLASH_QUIET_TEST
#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */
#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
#define CONFIG_SYS_FLASH_EMPTY_INFO
#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS}
/* CPLD on IFC */
#define CPLD_LBMAP_MASK 0x3F
#define CPLD_BANK_SEL_MASK 0x07
#define CPLD_BANK_OVERRIDE 0x40
#define CPLD_LBMAP_ALTBANK 0x44 /* BANK OR | BANK 4 */
#define CPLD_LBMAP_DFLTBANK 0x40 /* BANK OR | BANK0 */
#define CPLD_LBMAP_RESET 0xFF
#define CPLD_LBMAP_SHIFT 0x03
#if defined(CONFIG_TARGET_T1042RDB_PI)
#define CPLD_DIU_SEL_DFP 0x80
#elif defined(CONFIG_TARGET_T1042D4RDB)
#define CPLD_DIU_SEL_DFP 0xc0
#endif
#if defined(CONFIG_TARGET_T1040D4RDB)
#define CPLD_INT_MASK_ALL 0xFF
#define CPLD_INT_MASK_THERM 0x80
#define CPLD_INT_MASK_DVI_DFP 0x40
#define CPLD_INT_MASK_QSGMII1 0x20
#define CPLD_INT_MASK_QSGMII2 0x10
#define CPLD_INT_MASK_SGMI1 0x08
#define CPLD_INT_MASK_SGMI2 0x04
#define CPLD_INT_MASK_TDMR1 0x02
#define CPLD_INT_MASK_TDMR2 0x01
#endif
#define CONFIG_SYS_CPLD_BASE 0xffdf0000
#define CONFIG_SYS_CPLD_BASE_PHYS (0xf00000000ull | CONFIG_SYS_CPLD_BASE)
#define CONFIG_SYS_CSPR2_EXT (0xf)
#define CONFIG_SYS_CSPR2 (CSPR_PHYS_ADDR(CONFIG_SYS_CPLD_BASE_PHYS) \
| CSPR_PORT_SIZE_8 \
| CSPR_MSEL_GPCM \
| CSPR_V)
#define CONFIG_SYS_AMASK2 IFC_AMASK(64*1024)
#define CONFIG_SYS_CSOR2 0x0
/* CPLD Timing parameters for IFC CS2 */
#define CONFIG_SYS_CS2_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \
FTIM0_GPCM_TEADC(0x0e) | \
FTIM0_GPCM_TEAHC(0x0e))
#define CONFIG_SYS_CS2_FTIM1 (FTIM1_GPCM_TACO(0x0e) | \
FTIM1_GPCM_TRAD(0x1f))
#define CONFIG_SYS_CS2_FTIM2 (FTIM2_GPCM_TCS(0x0e) | \
FTIM2_GPCM_TCH(0x8) | \
FTIM2_GPCM_TWP(0x1f))
#define CONFIG_SYS_CS2_FTIM3 0x0
/* NAND Flash on IFC */
#define CONFIG_NAND_FSL_IFC
#define CONFIG_SYS_NAND_BASE 0xff800000
#define CONFIG_SYS_NAND_BASE_PHYS (0xf00000000ull | CONFIG_SYS_NAND_BASE)
#define CONFIG_SYS_NAND_CSPR_EXT (0xf)
#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
| CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
| CSPR_MSEL_NAND /* MSEL = NAND */ \
| CSPR_V)
#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024)
#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \
| CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \
| CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \
| CSOR_NAND_RAL_3 /* RAL = 3Byes */ \
| CSOR_NAND_PGS_4K /* Page Size = 4K */ \
| CSOR_NAND_SPRZ_224/* Spare size = 224 */ \
| CSOR_NAND_PB(64)) /*Pages Per Block = 64*/
#define CONFIG_SYS_NAND_ONFI_DETECTION
/* ONFI NAND Flash mode0 Timing Params */
#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \
FTIM0_NAND_TWP(0x18) | \
FTIM0_NAND_TWCHT(0x07) | \
FTIM0_NAND_TWH(0x0a))
#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \
FTIM1_NAND_TWBE(0x39) | \
FTIM1_NAND_TRR(0x0e) | \
FTIM1_NAND_TRP(0x18))
#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \
FTIM2_NAND_TREH(0x0a) | \
FTIM2_NAND_TWHRE(0x1e))
#define CONFIG_SYS_NAND_FTIM3 0x0
#define CONFIG_SYS_NAND_DDR_LAW 11
#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_CMD_NAND
#define CONFIG_SYS_NAND_BLOCK_SIZE (512 * 1024)
#if defined(CONFIG_NAND)
#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT
#define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR
#define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK
#define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR
#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0
#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1
#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2
#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3
#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR_CSPR_EXT
#define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR_CSPR
#define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK
#define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR
#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0
#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1
#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2
#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3
#else
#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR_CSPR_EXT
#define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR_CSPR
#define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK
#define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR
#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0
#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1
#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2
#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3
#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NAND_CSPR_EXT
#define CONFIG_SYS_CSPR1 CONFIG_SYS_NAND_CSPR
#define CONFIG_SYS_AMASK1 CONFIG_SYS_NAND_AMASK
#define CONFIG_SYS_CSOR1 CONFIG_SYS_NAND_CSOR
#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NAND_FTIM0
#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NAND_FTIM1
#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NAND_FTIM2
#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NAND_FTIM3
#endif
#ifdef CONFIG_SPL_BUILD
#define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE
#else
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
#endif
#if defined(CONFIG_RAMBOOT_PBL)
#define CONFIG_SYS_RAMBOOT
#endif
#ifdef CONFIG_SYS_FSL_ERRATUM_A008044
#if defined(CONFIG_NAND)
#define CONFIG_A008044_WORKAROUND
#endif
#endif
#define CONFIG_BOARD_EARLY_INIT_R
#define CONFIG_MISC_INIT_R
#define CONFIG_HWCONFIG
/* define to use L1 as initial stack */
#define CONFIG_L1_INIT_RAM
#define CONFIG_SYS_INIT_RAM_LOCK
#define CONFIG_SYS_INIT_RAM_ADDR 0xfdd00000 /* Initial L1 address */
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW 0xfe03c000
/* The assembler doesn't like typecast */
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
#define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024)
/* Serial Port - controlled on board with jumper J8
* open - index 2
* shorted - index 1
*/
#define CONFIG_CONS_INDEX 1
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2)
#define CONFIG_SYS_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500)
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600)
#define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500)
#define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600)
#if defined(CONFIG_TARGET_T1042RDB_PI) || defined(CONFIG_TARGET_T1042D4RDB)
/* Video */
#define CONFIG_FSL_DIU_FB
#ifdef CONFIG_FSL_DIU_FB
#define CONFIG_FSL_DIU_CH7301
#define CONFIG_SYS_DIU_ADDR (CONFIG_SYS_CCSRBAR + 0x180000)
#define CONFIG_CMD_BMP
#define CONFIG_VIDEO_LOGO
#define CONFIG_VIDEO_BMP_LOGO
#endif
#endif
/* I2C */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_FSL /* Use FSL common I2C driver */
#define CONFIG_SYS_FSL_I2C_SPEED 400000 /* I2C speed in Hz */
#define CONFIG_SYS_FSL_I2C2_SPEED 400000
#define CONFIG_SYS_FSL_I2C3_SPEED 400000
#define CONFIG_SYS_FSL_I2C4_SPEED 400000
#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
#define CONFIG_SYS_FSL_I2C3_SLAVE 0x7F
#define CONFIG_SYS_FSL_I2C4_SLAVE 0x7F
#define CONFIG_SYS_FSL_I2C_OFFSET 0x118000
#define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100
#define CONFIG_SYS_FSL_I2C3_OFFSET 0x119000
#define CONFIG_SYS_FSL_I2C4_OFFSET 0x119100
/* I2C bus multiplexer */
#define I2C_MUX_PCA_ADDR 0x70
#define I2C_MUX_CH_DEFAULT 0x8
#if defined(CONFIG_TARGET_T1042RDB_PI) || \
defined(CONFIG_TARGET_T1040D4RDB) || \
defined(CONFIG_TARGET_T1042D4RDB)
/* LDI/DVI Encoder for display */
#define CONFIG_SYS_I2C_LDI_ADDR 0x38
#define CONFIG_SYS_I2C_DVI_ADDR 0x75
/*
* RTC configuration
*/
#define RTC
#define CONFIG_RTC_DS1337 1
#define CONFIG_SYS_I2C_RTC_ADDR 0x68
/*DVI encoder*/
#define CONFIG_HDMI_ENCODER_I2C_ADDR 0x75
#endif
/*
* eSPI - Enhanced SPI
*/
#define CONFIG_SPI_FLASH_BAR
#define CONFIG_SF_DEFAULT_SPEED 10000000
#define CONFIG_SF_DEFAULT_MODE 0
#define CONFIG_ENV_SPI_BUS 0
#define CONFIG_ENV_SPI_CS 0
#define CONFIG_ENV_SPI_MAX_HZ 10000000
#define CONFIG_ENV_SPI_MODE 0
/*
* General PCI
* Memory space is mapped 1-1, but I/O space must start from 0.
*/
#ifdef CONFIG_PCI
/* controller 1, direct to uli, tgtid 3, Base address 20000 */
#ifdef CONFIG_PCIE1
#define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000
#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000
#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull
#define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000 /* 256M */
#define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000
#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
#define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull
#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
#endif
/* controller 2, Slot 2, tgtid 2, Base address 201000 */
#ifdef CONFIG_PCIE2
#define CONFIG_SYS_PCIE2_MEM_VIRT 0x90000000
#define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000
#define CONFIG_SYS_PCIE2_MEM_PHYS 0xc10000000ull
#define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */
#define CONFIG_SYS_PCIE2_IO_VIRT 0xf8010000
#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000
#define CONFIG_SYS_PCIE2_IO_PHYS 0xff8010000ull
#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */
#endif
/* controller 3, Slot 1, tgtid 1, Base address 202000 */
#ifdef CONFIG_PCIE3
#define CONFIG_SYS_PCIE3_MEM_VIRT 0xa0000000
#define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000
#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc20000000ull
#define CONFIG_SYS_PCIE3_MEM_SIZE 0x10000000 /* 256M */
#define CONFIG_SYS_PCIE3_IO_VIRT 0xf8020000
#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000
#define CONFIG_SYS_PCIE3_IO_PHYS 0xff8020000ull
#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */
#endif
/* controller 4, Base address 203000 */
#ifdef CONFIG_PCIE4
#define CONFIG_SYS_PCIE4_MEM_VIRT 0xb0000000
#define CONFIG_SYS_PCIE4_MEM_BUS 0xe0000000
#define CONFIG_SYS_PCIE4_MEM_PHYS 0xc30000000ull
#define CONFIG_SYS_PCIE4_MEM_SIZE 0x10000000 /* 256M */
#define CONFIG_SYS_PCIE4_IO_VIRT 0xf8030000
#define CONFIG_SYS_PCIE4_IO_BUS 0x00000000
#define CONFIG_SYS_PCIE4_IO_PHYS 0xff8030000ull
#define CONFIG_SYS_PCIE4_IO_SIZE 0x00010000 /* 64k */
#endif
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
#endif /* CONFIG_PCI */
/* SATA */
#define CONFIG_FSL_SATA_V2
#ifdef CONFIG_FSL_SATA_V2
#define CONFIG_LIBATA
#define CONFIG_FSL_SATA
#define CONFIG_SYS_SATA_MAX_DEVICE 1
#define CONFIG_SATA1
#define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR
#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA
#define CONFIG_LBA48
#define CONFIG_CMD_SATA
#endif
/*
* USB
*/
#define CONFIG_HAS_FSL_DR_USB
#ifdef CONFIG_HAS_FSL_DR_USB
#define CONFIG_USB_EHCI
#ifdef CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_FSL
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#endif
#endif
#ifdef CONFIG_MMC
#define CONFIG_FSL_ESDHC
#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR
#define CONFIG_GENERIC_MMC
#endif
/* Qman/Bman */
#ifndef CONFIG_NOBQFMAN
#define CONFIG_SYS_DPAA_QBMAN /* Support Q/Bman */
#define CONFIG_SYS_BMAN_NUM_PORTALS 10
#define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000
#define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull
#define CONFIG_SYS_BMAN_MEM_SIZE 0x02000000
#define CONFIG_SYS_BMAN_SP_CENA_SIZE 0x4000
#define CONFIG_SYS_BMAN_SP_CINH_SIZE 0x1000
#define CONFIG_SYS_BMAN_CENA_BASE CONFIG_SYS_BMAN_MEM_BASE
#define CONFIG_SYS_BMAN_CENA_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
#define CONFIG_SYS_BMAN_CINH_BASE (CONFIG_SYS_BMAN_MEM_BASE + \
CONFIG_SYS_BMAN_CENA_SIZE)
#define CONFIG_SYS_BMAN_CINH_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
#define CONFIG_SYS_BMAN_SWP_ISDR_REG 0xE08
#define CONFIG_SYS_QMAN_NUM_PORTALS 10
#define CONFIG_SYS_QMAN_MEM_BASE 0xf6000000
#define CONFIG_SYS_QMAN_MEM_PHYS 0xff6000000ull
#define CONFIG_SYS_QMAN_MEM_SIZE 0x02000000
#define CONFIG_SYS_QMAN_SP_CENA_SIZE 0x4000
#define CONFIG_SYS_QMAN_SP_CINH_SIZE 0x1000
#define CONFIG_SYS_QMAN_CENA_BASE CONFIG_SYS_QMAN_MEM_BASE
#define CONFIG_SYS_QMAN_CENA_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
#define CONFIG_SYS_QMAN_CINH_BASE (CONFIG_SYS_QMAN_MEM_BASE + \
CONFIG_SYS_QMAN_CENA_SIZE)
#define CONFIG_SYS_QMAN_CINH_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
#define CONFIG_SYS_QMAN_SWP_ISDR_REG 0xE08
#define CONFIG_SYS_DPAA_FMAN
#define CONFIG_SYS_DPAA_PME
#define CONFIG_QE
#define CONFIG_U_QE
/* Default address of microcode for the Linux Fman driver */
#if defined(CONFIG_SPIFLASH)
/*
* env is stored at 0x100000, sector size is 0x10000, ucode is stored after
* env, so we got 0x110000.
*/
#define CONFIG_SYS_QE_FW_IN_SPIFLASH
#define CONFIG_SYS_FMAN_FW_ADDR 0x110000
#elif defined(CONFIG_SDCARD)
/*
* PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
* about 1MB (2048 blocks), Env is stored after the image, and the env size is
* 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 2080.
*/
#define CONFIG_SYS_QE_FMAN_FW_IN_MMC
#define CONFIG_SYS_FMAN_FW_ADDR (512 * 0x820)
#elif defined(CONFIG_NAND)
#define CONFIG_SYS_QE_FMAN_FW_IN_NAND
#define CONFIG_SYS_FMAN_FW_ADDR (5 * CONFIG_SYS_NAND_BLOCK_SIZE)
#else
#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
#define CONFIG_SYS_FMAN_FW_ADDR 0xEFF00000
#endif
#if defined(CONFIG_SPIFLASH)
#define CONFIG_SYS_QE_FW_ADDR 0x130000
#elif defined(CONFIG_SDCARD)
#define CONFIG_SYS_QE_FW_ADDR (512 * 0x920)
#elif defined(CONFIG_NAND)
#define CONFIG_SYS_QE_FW_ADDR (7 * CONFIG_SYS_NAND_BLOCK_SIZE)
#else
#define CONFIG_SYS_QE_FW_ADDR 0xEFF10000
#endif
#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000
#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
#endif /* CONFIG_NOBQFMAN */
#ifdef CONFIG_SYS_DPAA_FMAN
#define CONFIG_FMAN_ENET
#define CONFIG_PHY_VITESSE
#define CONFIG_PHY_REALTEK
#endif
#ifdef CONFIG_FMAN_ENET
#if defined(CONFIG_TARGET_T1040RDB) || defined(CONFIG_TARGET_T1042RDB)
#define CONFIG_SYS_SGMII1_PHY_ADDR 0x03
#elif defined(CONFIG_TARGET_T1040D4RDB)
#define CONFIG_SYS_SGMII1_PHY_ADDR 0x01
#elif defined(CONFIG_TARGET_T1042D4RDB)
#define CONFIG_SYS_SGMII1_PHY_ADDR 0x02
#define CONFIG_SYS_SGMII2_PHY_ADDR 0x03
#define CONFIG_SYS_SGMII3_PHY_ADDR 0x01
#endif
#if defined(CONFIG_TARGET_T1040D4RDB) || defined(CONFIG_TARGET_T1042D4RDB)
#define CONFIG_SYS_RGMII1_PHY_ADDR 0x04
#define CONFIG_SYS_RGMII2_PHY_ADDR 0x05
#else
#define CONFIG_SYS_RGMII1_PHY_ADDR 0x01
#define CONFIG_SYS_RGMII2_PHY_ADDR 0x02
#endif
/* Enable VSC9953 L2 Switch driver on T1040 SoC */
#if defined(CONFIG_TARGET_T1040RDB) || defined(CONFIG_TARGET_T1040D4RDB)
#define CONFIG_VSC9953
#define CONFIG_CMD_ETHSW
#ifdef CONFIG_TARGET_T1040RDB
#define CONFIG_SYS_FM1_QSGMII11_PHY_ADDR 0x04
#define CONFIG_SYS_FM1_QSGMII21_PHY_ADDR 0x08
#else
#define CONFIG_SYS_FM1_QSGMII11_PHY_ADDR 0x08
#define CONFIG_SYS_FM1_QSGMII21_PHY_ADDR 0x0c
#endif
#endif
#define CONFIG_MII /* MII PHY management */
#define CONFIG_ETHPRIME "FM1@DTSEC4"
#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */
#endif
/*
* Environment
*/
#define CONFIG_LOADS_ECHO /* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
/*
* Command line configuration.
*/
#ifdef CONFIG_TARGET_T1042RDB_PI
#define CONFIG_CMD_DATE
#endif
#define CONFIG_CMD_ERRATA
#define CONFIG_CMD_IRQ
#define CONFIG_CMD_REGINFO
#ifdef CONFIG_PCI
#define CONFIG_CMD_PCI
#endif
/* Hash command with SHA acceleration supported in hardware */
#ifdef CONFIG_FSL_CAAM
#define CONFIG_CMD_HASH
#define CONFIG_SHA_HW_ACCEL
#endif
/*
* Miscellaneous configurable options
*/
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_CMDLINE_EDITING /* Command-line editing */
#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
#ifdef CONFIG_CMD_KGDB
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */
/*
* For booting Linux, the board info and command line data
* have to be in the first 64 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial map for Linux*/
#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
#ifdef CONFIG_CMD_KGDB
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
#endif
/*
* Dynamic MTD Partition support with mtdparts
*/
#ifndef CONFIG_SYS_NO_FLASH
#define CONFIG_MTD_DEVICE
#define CONFIG_MTD_PARTITIONS
#define CONFIG_CMD_MTDPARTS
#define CONFIG_FLASH_CFI_MTD
#define MTDIDS_DEFAULT "nor0=fe8000000.nor,nand0=fff800000.flash," \
"spi0=spife110000.0"
#define MTDPARTS_DEFAULT "mtdparts=fe8000000.nor:1m(uboot),5m(kernel)," \
"128k(dtb),96m(fs),-(user);"\
"fff800000.flash:2m(uboot),9m(kernel),"\
"128k(dtb),96m(fs),-(user);spife110000.0:" \
"2m(uboot),9m(kernel),128k(dtb),-(user)"
#endif
/*
* Environment Configuration
*/
#define CONFIG_ROOTPATH "/opt/nfsroot"
#define CONFIG_BOOTFILE "uImage"
#define CONFIG_UBOOTPATH "u-boot.bin" /* U-Boot image on TFTP server*/
/* default location for tftp and bootm */
#define CONFIG_LOADADDR 1000000
#define CONFIG_BAUDRATE 115200
#define __USB_PHY_TYPE utmi
#define RAMDISKFILE "t104xrdb/ramdisk.uboot"
#ifdef CONFIG_TARGET_T1040RDB
#define FDTFILE "t1040rdb/t1040rdb.dtb"
#elif defined(CONFIG_TARGET_T1042RDB_PI)
#define FDTFILE "t1042rdb_pi/t1042rdb_pi.dtb"
#elif defined(CONFIG_TARGET_T1042RDB)
#define FDTFILE "t1042rdb/t1042rdb.dtb"
#elif defined(CONFIG_TARGET_T1040D4RDB)
#define FDTFILE "t1042rdb/t1040d4rdb.dtb"
#elif defined(CONFIG_TARGET_T1042D4RDB)
#define FDTFILE "t1042rdb/t1042d4rdb.dtb"
#endif
#ifdef CONFIG_FSL_DIU_FB
#define DIU_ENVIRONMENT "video-mode=fslfb:1024x768-32@60,monitor=dvi"
#else
#define DIU_ENVIRONMENT
#endif
#define CONFIG_EXTRA_ENV_SETTINGS \
"hwconfig=fsl_ddr:bank_intlv=cs0_cs1;" \
"usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) ";"\
"usb2:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
"netdev=eth0\0" \
"video-mode=" __stringify(DIU_ENVIRONMENT) "\0" \
"uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \
"ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \
"tftpflash=tftpboot $loadaddr $uboot && " \
"protect off $ubootaddr +$filesize && " \
"erase $ubootaddr +$filesize && " \
"cp.b $loadaddr $ubootaddr $filesize && " \
"protect on $ubootaddr +$filesize && " \
"cmp.b $loadaddr $ubootaddr $filesize\0" \
"consoledev=ttyS0\0" \
"ramdiskaddr=2000000\0" \
"ramdiskfile=" __stringify(RAMDISKFILE) "\0" \
"fdtaddr=1e00000\0" \
"fdtfile=" __stringify(FDTFILE) "\0" \
"bdev=sda3\0"
#define CONFIG_LINUX \
"setenv bootargs root=/dev/ram rw " \
"console=$consoledev,$baudrate $othbootargs;" \
"setenv ramdiskaddr 0x02000000;" \
"setenv fdtaddr 0x00c00000;" \
"setenv loadaddr 0x1000000;" \
"bootm $loadaddr $ramdiskaddr $fdtaddr"
#define CONFIG_HDBOOT \
"setenv bootargs root=/dev/$bdev rw " \
"console=$consoledev,$baudrate $othbootargs;" \
"tftp $loadaddr $bootfile;" \
"tftp $fdtaddr $fdtfile;" \
"bootm $loadaddr - $fdtaddr"
#define CONFIG_NFSBOOTCOMMAND \
"setenv bootargs root=/dev/nfs rw " \
"nfsroot=$serverip:$rootpath " \
"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
"console=$consoledev,$baudrate $othbootargs;" \
"tftp $loadaddr $bootfile;" \
"tftp $fdtaddr $fdtfile;" \
"bootm $loadaddr - $fdtaddr"
#define CONFIG_RAMBOOTCOMMAND \
"setenv bootargs root=/dev/ram rw " \
"console=$consoledev,$baudrate $othbootargs;" \
"tftp $ramdiskaddr $ramdiskfile;" \
"tftp $loadaddr $bootfile;" \
"tftp $fdtaddr $fdtfile;" \
"bootm $loadaddr $ramdiskaddr $fdtaddr"
#define CONFIG_BOOTCOMMAND CONFIG_LINUX
#include <asm/fsl_secure_boot.h>
#endif /* __CONFIG_H */