blob: 7d51821497b46987ad4dca3b53705d81b68b4229 [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0+
/*
* Driver for the Atmel USBA high speed USB device controller
* [Original from Linux kernel: drivers/usb/gadget/atmel_usba_udc.c]
*
* Copyright (C) 2005-2013 Atmel Corporation
* Bo Shen <voice.shen@atmel.com>
*/
#include <common.h>
#include <linux/bitops.h>
#include <linux/errno.h>
#include <asm/gpio.h>
#include <asm/hardware.h>
#include <linux/list.h>
#include <linux/usb/ch9.h>
#include <linux/usb/gadget.h>
#include <linux/usb/atmel_usba_udc.h>
#include <malloc.h>
#include "atmel_usba_udc.h"
static int vbus_is_present(struct usba_udc *udc)
{
/* No Vbus detection: Assume always present */
return 1;
}
static void next_fifo_transaction(struct usba_ep *ep, struct usba_request *req)
{
unsigned int transaction_len;
transaction_len = req->req.length - req->req.actual;
req->last_transaction = 1;
if (transaction_len > ep->ep.maxpacket) {
transaction_len = ep->ep.maxpacket;
req->last_transaction = 0;
} else if (transaction_len == ep->ep.maxpacket && req->req.zero) {
req->last_transaction = 0;
}
DBG(DBG_QUEUE, "%s: submit_transaction, req %p (length %d)%s\n",
ep->ep.name, req, transaction_len,
req->last_transaction ? ", done" : "");
memcpy(ep->fifo, req->req.buf + req->req.actual, transaction_len);
usba_ep_writel(ep, SET_STA, USBA_TX_PK_RDY);
req->req.actual += transaction_len;
}
static void submit_request(struct usba_ep *ep, struct usba_request *req)
{
DBG(DBG_QUEUE, "%s: submit_request: req %p (length %d), dma: %d\n",
ep->ep.name, req, req->req.length, req->using_dma);
req->req.actual = 0;
req->submitted = 1;
next_fifo_transaction(ep, req);
if (req->last_transaction) {
usba_ep_writel(ep, CTL_DIS, USBA_TX_PK_RDY);
usba_ep_writel(ep, CTL_ENB, USBA_TX_COMPLETE);
} else {
usba_ep_writel(ep, CTL_DIS, USBA_TX_COMPLETE);
usba_ep_writel(ep, CTL_ENB, USBA_TX_PK_RDY);
}
}
static void submit_next_request(struct usba_ep *ep)
{
struct usba_request *req;
if (list_empty(&ep->queue)) {
usba_ep_writel(ep, CTL_DIS, USBA_TX_PK_RDY | USBA_RX_BK_RDY);
return;
}
req = list_entry(ep->queue.next, struct usba_request, queue);
if (!req->submitted)
submit_request(ep, req);
}
static void send_status(struct usba_udc *udc, struct usba_ep *ep)
{
ep->state = STATUS_STAGE_IN;
usba_ep_writel(ep, SET_STA, USBA_TX_PK_RDY);
usba_ep_writel(ep, CTL_ENB, USBA_TX_COMPLETE);
}
static void receive_data(struct usba_ep *ep)
{
struct usba_udc *udc = ep->udc;
struct usba_request *req;
unsigned long status;
unsigned int bytecount, nr_busy;
int is_complete = 0;
status = usba_ep_readl(ep, STA);
nr_busy = USBA_BFEXT(BUSY_BANKS, status);
DBG(DBG_QUEUE, "receive data: nr_busy=%u\n", nr_busy);
while (nr_busy > 0) {
if (list_empty(&ep->queue)) {
usba_ep_writel(ep, CTL_DIS, USBA_RX_BK_RDY);
break;
}
req = list_entry(ep->queue.next,
struct usba_request, queue);
bytecount = USBA_BFEXT(BYTE_COUNT, status);
if (status & USBA_SHORT_PACKET)
is_complete = 1;
if (req->req.actual + bytecount >= req->req.length) {
is_complete = 1;
bytecount = req->req.length - req->req.actual;
}
memcpy(req->req.buf + req->req.actual, ep->fifo, bytecount);
req->req.actual += bytecount;
usba_ep_writel(ep, CLR_STA, USBA_RX_BK_RDY);
if (is_complete) {
DBG(DBG_QUEUE, "%s: request done\n", ep->ep.name);
req->req.status = 0;
list_del_init(&req->queue);
usba_ep_writel(ep, CTL_DIS, USBA_RX_BK_RDY);
spin_lock(&udc->lock);
req->req.complete(&ep->ep, &req->req);
spin_unlock(&udc->lock);
}
status = usba_ep_readl(ep, STA);
nr_busy = USBA_BFEXT(BUSY_BANKS, status);
if (is_complete && ep_is_control(ep)) {
send_status(udc, ep);
break;
}
}
}
static void
request_complete(struct usba_ep *ep, struct usba_request *req, int status)
{
if (req->req.status == -EINPROGRESS)
req->req.status = status;
DBG(DBG_GADGET | DBG_REQ, "%s: req %p complete: status %d, actual %u\n",
ep->ep.name, req, req->req.status, req->req.actual);
req->req.complete(&ep->ep, &req->req);
}
static void
request_complete_list(struct usba_ep *ep, struct list_head *list, int status)
{
struct usba_request *req, *tmp_req;
list_for_each_entry_safe(req, tmp_req, list, queue) {
list_del_init(&req->queue);
request_complete(ep, req, status);
}
}
static int
usba_ep_enable(struct usb_ep *_ep, const struct usb_endpoint_descriptor *desc)
{
struct usba_ep *ep = to_usba_ep(_ep);
struct usba_udc *udc = ep->udc;
unsigned long flags = 0, ept_cfg, maxpacket;
unsigned int nr_trans;
DBG(DBG_GADGET, "%s: ep_enable: desc=%p\n", ep->ep.name, desc);
maxpacket = usb_endpoint_maxp(desc) & 0x7ff;
if (((desc->bEndpointAddress & USB_ENDPOINT_NUMBER_MASK)
!= ep->index) ||
ep->index == 0 ||
desc->bDescriptorType != USB_DT_ENDPOINT ||
maxpacket == 0 ||
maxpacket > ep->fifo_size) {
DBG(DBG_ERR, "ep_enable: Invalid argument");
return -EINVAL;
}
ep->is_isoc = 0;
ep->is_in = 0;
if (maxpacket <= 8)
ept_cfg = USBA_BF(EPT_SIZE, USBA_EPT_SIZE_8);
else
/* LSB is bit 1, not 0 */
ept_cfg = USBA_BF(EPT_SIZE, fls(maxpacket - 1) - 3);
DBG(DBG_HW, "%s: EPT_SIZE = %lu (maxpacket = %lu)\n",
ep->ep.name, ept_cfg, maxpacket);
if (usb_endpoint_dir_in(desc)) {
ep->is_in = 1;
ept_cfg |= USBA_EPT_DIR_IN;
}
switch (usb_endpoint_type(desc)) {
case USB_ENDPOINT_XFER_CONTROL:
ept_cfg |= USBA_BF(EPT_TYPE, USBA_EPT_TYPE_CONTROL);
ept_cfg |= USBA_BF(BK_NUMBER, USBA_BK_NUMBER_ONE);
break;
case USB_ENDPOINT_XFER_ISOC:
if (!ep->can_isoc) {
DBG(DBG_ERR, "ep_enable: %s is not isoc capable\n",
ep->ep.name);
return -EINVAL;
}
/*
* Bits 11:12 specify number of _additional_
* transactions per microframe.
*/
nr_trans = ((usb_endpoint_maxp(desc) >> 11) & 3) + 1;
if (nr_trans > 3)
return -EINVAL;
ep->is_isoc = 1;
ept_cfg |= USBA_BF(EPT_TYPE, USBA_EPT_TYPE_ISO);
/*
* Do triple-buffering on high-bandwidth iso endpoints.
*/
if (nr_trans > 1 && ep->nr_banks == 3)
ept_cfg |= USBA_BF(BK_NUMBER, USBA_BK_NUMBER_TRIPLE);
else
ept_cfg |= USBA_BF(BK_NUMBER, USBA_BK_NUMBER_DOUBLE);
ept_cfg |= USBA_BF(NB_TRANS, nr_trans);
break;
case USB_ENDPOINT_XFER_BULK:
ept_cfg |= USBA_BF(EPT_TYPE, USBA_EPT_TYPE_BULK);
ept_cfg |= USBA_BF(BK_NUMBER, USBA_BK_NUMBER_ONE);
break;
case USB_ENDPOINT_XFER_INT:
ept_cfg |= USBA_BF(EPT_TYPE, USBA_EPT_TYPE_INT);
ept_cfg |= USBA_BF(BK_NUMBER, USBA_BK_NUMBER_ONE);
break;
}
spin_lock_irqsave(&ep->udc->lock, flags);
ep->desc = desc;
ep->ep.maxpacket = maxpacket;
usba_ep_writel(ep, CFG, ept_cfg);
usba_ep_writel(ep, CTL_ENB, USBA_EPT_ENABLE);
usba_writel(udc, INT_ENB,
(usba_readl(udc, INT_ENB)
| USBA_BF(EPT_INT, 1 << ep->index)));
spin_unlock_irqrestore(&udc->lock, flags);
DBG(DBG_HW, "EPT_CFG%d after init: %#08lx\n", ep->index,
(unsigned long)usba_ep_readl(ep, CFG));
DBG(DBG_HW, "INT_ENB after init: %#08lx\n",
(unsigned long)usba_readl(udc, INT_ENB));
return 0;
}
static int usba_ep_disable(struct usb_ep *_ep)
{
struct usba_ep *ep = to_usba_ep(_ep);
struct usba_udc *udc = ep->udc;
LIST_HEAD(req_list);
unsigned long flags = 0;
DBG(DBG_GADGET, "ep_disable: %s\n", ep->ep.name);
spin_lock_irqsave(&udc->lock, flags);
if (!ep->desc) {
spin_unlock_irqrestore(&udc->lock, flags);
/* REVISIT because this driver disables endpoints in
* reset_all_endpoints() before calling disconnect(),
* most gadget drivers would trigger this non-error ...
*/
if (udc->gadget.speed != USB_SPEED_UNKNOWN)
DBG(DBG_ERR, "ep_disable: %s not enabled\n",
ep->ep.name);
return -EINVAL;
}
ep->desc = NULL;
list_splice_init(&ep->queue, &req_list);
usba_ep_writel(ep, CFG, 0);
usba_ep_writel(ep, CTL_DIS, USBA_EPT_ENABLE);
usba_writel(udc, INT_ENB,
usba_readl(udc, INT_ENB) &
~USBA_BF(EPT_INT, 1 << ep->index));
request_complete_list(ep, &req_list, -ESHUTDOWN);
spin_unlock_irqrestore(&udc->lock, flags);
return 0;
}
static struct usb_request *
usba_ep_alloc_request(struct usb_ep *_ep, gfp_t gfp_flags)
{
struct usba_request *req;
DBG(DBG_GADGET, "ep_alloc_request: %p, 0x%x\n", _ep, gfp_flags);
req = calloc(1, sizeof(struct usba_request));
if (!req)
return NULL;
INIT_LIST_HEAD(&req->queue);
return &req->req;
}
static void
usba_ep_free_request(struct usb_ep *_ep, struct usb_request *_req)
{
struct usba_request *req = to_usba_req(_req);
DBG(DBG_GADGET, "ep_free_request: %p, %p\n", _ep, _req);
free(req);
}
static int
usba_ep_queue(struct usb_ep *_ep, struct usb_request *_req, gfp_t gfp_flags)
{
struct usba_request *req = to_usba_req(_req);
struct usba_ep *ep = to_usba_ep(_ep);
struct usba_udc *udc = ep->udc;
unsigned long flags = 0;
int ret;
DBG(DBG_GADGET | DBG_QUEUE | DBG_REQ, "%s: queue req %p, len %u\n",
ep->ep.name, req, _req->length);
if (!udc->driver || udc->gadget.speed == USB_SPEED_UNKNOWN ||
!ep->desc)
return -ESHUTDOWN;
req->submitted = 0;
req->using_dma = 0;
req->last_transaction = 0;
_req->status = -EINPROGRESS;
_req->actual = 0;
/* May have received a reset since last time we checked */
ret = -ESHUTDOWN;
spin_lock_irqsave(&udc->lock, flags);
if (ep->desc) {
list_add_tail(&req->queue, &ep->queue);
if ((!ep_is_control(ep) && ep->is_in) ||
(ep_is_control(ep) && (ep->state == DATA_STAGE_IN ||
ep->state == STATUS_STAGE_IN)))
usba_ep_writel(ep, CTL_ENB, USBA_TX_PK_RDY);
else
usba_ep_writel(ep, CTL_ENB, USBA_RX_BK_RDY);
ret = 0;
}
spin_unlock_irqrestore(&udc->lock, flags);
return ret;
}
static int usba_ep_dequeue(struct usb_ep *_ep, struct usb_request *_req)
{
struct usba_ep *ep = to_usba_ep(_ep);
struct usba_request *req = to_usba_req(_req);
DBG(DBG_GADGET | DBG_QUEUE, "ep_dequeue: %s, req %p\n",
ep->ep.name, req);
/*
* Errors should stop the queue from advancing until the
* completion function returns.
*/
list_del_init(&req->queue);
request_complete(ep, req, -ECONNRESET);
/* Process the next request if any */
submit_next_request(ep);
return 0;
}
static int usba_ep_set_halt(struct usb_ep *_ep, int value)
{
struct usba_ep *ep = to_usba_ep(_ep);
unsigned long flags = 0;
int ret = 0;
DBG(DBG_GADGET, "endpoint %s: %s HALT\n", ep->ep.name,
value ? "set" : "clear");
if (!ep->desc) {
DBG(DBG_ERR, "Attempted to halt uninitialized ep %s\n",
ep->ep.name);
return -ENODEV;
}
if (ep->is_isoc) {
DBG(DBG_ERR, "Attempted to halt isochronous ep %s\n",
ep->ep.name);
return -ENOTTY;
}
spin_lock_irqsave(&udc->lock, flags);
/*
* We can't halt IN endpoints while there are still data to be
* transferred
*/
if (!list_empty(&ep->queue) ||
((value && ep->is_in && (usba_ep_readl(ep, STA) &
USBA_BF(BUSY_BANKS, -1L))))) {
ret = -EAGAIN;
} else {
if (value)
usba_ep_writel(ep, SET_STA, USBA_FORCE_STALL);
else
usba_ep_writel(ep, CLR_STA,
USBA_FORCE_STALL | USBA_TOGGLE_CLR);
usba_ep_readl(ep, STA);
}
spin_unlock_irqrestore(&udc->lock, flags);
return ret;
}
static int usba_ep_fifo_status(struct usb_ep *_ep)
{
struct usba_ep *ep = to_usba_ep(_ep);
return USBA_BFEXT(BYTE_COUNT, usba_ep_readl(ep, STA));
}
static void usba_ep_fifo_flush(struct usb_ep *_ep)
{
struct usba_ep *ep = to_usba_ep(_ep);
struct usba_udc *udc = ep->udc;
usba_writel(udc, EPT_RST, 1 << ep->index);
}
static const struct usb_ep_ops usba_ep_ops = {
.enable = usba_ep_enable,
.disable = usba_ep_disable,
.alloc_request = usba_ep_alloc_request,
.free_request = usba_ep_free_request,
.queue = usba_ep_queue,
.dequeue = usba_ep_dequeue,
.set_halt = usba_ep_set_halt,
.fifo_status = usba_ep_fifo_status,
.fifo_flush = usba_ep_fifo_flush,
};
static int usba_udc_get_frame(struct usb_gadget *gadget)
{
struct usba_udc *udc = to_usba_udc(gadget);
return USBA_BFEXT(FRAME_NUMBER, usba_readl(udc, FNUM));
}
static int usba_udc_wakeup(struct usb_gadget *gadget)
{
struct usba_udc *udc = to_usba_udc(gadget);
unsigned long flags = 0;
u32 ctrl;
int ret = -EINVAL;
spin_lock_irqsave(&udc->lock, flags);
if (udc->devstatus & (1 << USB_DEVICE_REMOTE_WAKEUP)) {
ctrl = usba_readl(udc, CTRL);
usba_writel(udc, CTRL, ctrl | USBA_REMOTE_WAKE_UP);
ret = 0;
}
spin_unlock_irqrestore(&udc->lock, flags);
return ret;
}
static int
usba_udc_set_selfpowered(struct usb_gadget *gadget, int is_selfpowered)
{
struct usba_udc *udc = to_usba_udc(gadget);
unsigned long flags = 0;
spin_lock_irqsave(&udc->lock, flags);
if (is_selfpowered)
udc->devstatus |= 1 << USB_DEVICE_SELF_POWERED;
else
udc->devstatus &= ~(1 << USB_DEVICE_SELF_POWERED);
spin_unlock_irqrestore(&udc->lock, flags);
return 0;
}
static const struct usb_gadget_ops usba_udc_ops = {
.get_frame = usba_udc_get_frame,
.wakeup = usba_udc_wakeup,
.set_selfpowered = usba_udc_set_selfpowered,
};
static struct usb_endpoint_descriptor usba_ep0_desc = {
.bLength = USB_DT_ENDPOINT_SIZE,
.bDescriptorType = USB_DT_ENDPOINT,
.bEndpointAddress = 0,
.bmAttributes = USB_ENDPOINT_XFER_CONTROL,
.wMaxPacketSize = cpu_to_le16(64),
/* FIXME: I have no idea what to put here */
.bInterval = 1,
};
/*
* Called with interrupts disabled and udc->lock held.
*/
static void reset_all_endpoints(struct usba_udc *udc)
{
struct usba_ep *ep;
struct usba_request *req, *tmp_req;
usba_writel(udc, EPT_RST, ~0UL);
ep = to_usba_ep(udc->gadget.ep0);
list_for_each_entry_safe(req, tmp_req, &ep->queue, queue) {
list_del_init(&req->queue);
request_complete(ep, req, -ECONNRESET);
}
/* NOTE: normally, the next call to the gadget driver is in
* charge of disabling endpoints... usually disconnect().
* The exception would be entering a high speed test mode.
*
* FIXME remove this code ... and retest thoroughly.
*/
list_for_each_entry(ep, &udc->gadget.ep_list, ep.ep_list) {
if (ep->desc) {
spin_unlock(&udc->lock);
usba_ep_disable(&ep->ep);
spin_lock(&udc->lock);
}
}
}
static struct usba_ep *get_ep_by_addr(struct usba_udc *udc, u16 wIndex)
{
struct usba_ep *ep;
if ((wIndex & USB_ENDPOINT_NUMBER_MASK) == 0)
return to_usba_ep(udc->gadget.ep0);
list_for_each_entry(ep, &udc->gadget.ep_list, ep.ep_list) {
u8 bEndpointAddress;
if (!ep->desc)
continue;
bEndpointAddress = ep->desc->bEndpointAddress;
if ((wIndex ^ bEndpointAddress) & USB_DIR_IN)
continue;
if ((bEndpointAddress & USB_ENDPOINT_NUMBER_MASK)
== (wIndex & USB_ENDPOINT_NUMBER_MASK))
return ep;
}
return NULL;
}
/* Called with interrupts disabled and udc->lock held */
static inline void set_protocol_stall(struct usba_udc *udc, struct usba_ep *ep)
{
usba_ep_writel(ep, SET_STA, USBA_FORCE_STALL);
ep->state = WAIT_FOR_SETUP;
}
static inline int is_stalled(struct usba_udc *udc, struct usba_ep *ep)
{
if (usba_ep_readl(ep, STA) & USBA_FORCE_STALL)
return 1;
return 0;
}
static inline void set_address(struct usba_udc *udc, unsigned int addr)
{
u32 regval;
DBG(DBG_BUS, "setting address %u...\n", addr);
regval = usba_readl(udc, CTRL);
regval = USBA_BFINS(DEV_ADDR, addr, regval);
usba_writel(udc, CTRL, regval);
}
static int do_test_mode(struct usba_udc *udc)
{
static const char test_packet_buffer[] = {
/* JKJKJKJK * 9 */
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
/* JJKKJJKK * 8 */
0xAA, 0xAA, 0xAA, 0xAA, 0xAA, 0xAA, 0xAA, 0xAA,
/* JJKKJJKK * 8 */
0xEE, 0xEE, 0xEE, 0xEE, 0xEE, 0xEE, 0xEE, 0xEE,
/* JJJJJJJKKKKKKK * 8 */
0xFE, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
/* JJJJJJJK * 8 */
0x7F, 0xBF, 0xDF, 0xEF, 0xF7, 0xFB, 0xFD,
/* {JKKKKKKK * 10}, JK */
0xFC, 0x7E, 0xBF, 0xDF, 0xEF, 0xF7, 0xFB, 0xFD, 0x7E
};
struct usba_ep *ep;
int test_mode;
test_mode = udc->test_mode;
/* Start from a clean slate */
reset_all_endpoints(udc);
switch (test_mode) {
case 0x0100:
/* Test_J */
usba_writel(udc, TST, USBA_TST_J_MODE);
DBG(DBG_ALL, "Entering Test_J mode...\n");
break;
case 0x0200:
/* Test_K */
usba_writel(udc, TST, USBA_TST_K_MODE);
DBG(DBG_ALL, "Entering Test_K mode...\n");
break;
case 0x0300:
/*
* Test_SE0_NAK: Force high-speed mode and set up ep0
* for Bulk IN transfers
*/
ep = &udc->usba_ep[0];
usba_writel(udc, TST,
USBA_BF(SPEED_CFG, USBA_SPEED_CFG_FORCE_HIGH));
usba_ep_writel(ep, CFG,
USBA_BF(EPT_SIZE, USBA_EPT_SIZE_64)
| USBA_EPT_DIR_IN
| USBA_BF(EPT_TYPE, USBA_EPT_TYPE_BULK)
| USBA_BF(BK_NUMBER, 1));
if (!(usba_ep_readl(ep, CFG) & USBA_EPT_MAPPED)) {
set_protocol_stall(udc, ep);
DBG(DBG_ALL, "Test_SE0_NAK: ep0 not mapped\n");
} else {
usba_ep_writel(ep, CTL_ENB, USBA_EPT_ENABLE);
DBG(DBG_ALL, "Entering Test_SE0_NAK mode...\n");
}
break;
case 0x0400:
/* Test_Packet */
ep = &udc->usba_ep[0];
usba_ep_writel(ep, CFG,
USBA_BF(EPT_SIZE, USBA_EPT_SIZE_64)
| USBA_EPT_DIR_IN
| USBA_BF(EPT_TYPE, USBA_EPT_TYPE_BULK)
| USBA_BF(BK_NUMBER, 1));
if (!(usba_ep_readl(ep, CFG) & USBA_EPT_MAPPED)) {
set_protocol_stall(udc, ep);
DBG(DBG_ALL, "Test_Packet: ep0 not mapped\n");
} else {
usba_ep_writel(ep, CTL_ENB, USBA_EPT_ENABLE);
usba_writel(udc, TST, USBA_TST_PKT_MODE);
memcpy(ep->fifo, test_packet_buffer,
sizeof(test_packet_buffer));
usba_ep_writel(ep, SET_STA, USBA_TX_PK_RDY);
DBG(DBG_ALL, "Entering Test_Packet mode...\n");
}
break;
default:
DBG(DBG_ERR, "Invalid test mode: 0x%04x\n", test_mode);
return -EINVAL;
}
return 0;
}
/* Avoid overly long expressions */
static inline bool feature_is_dev_remote_wakeup(struct usb_ctrlrequest *crq)
{
if (crq->wValue == cpu_to_le16(USB_DEVICE_REMOTE_WAKEUP))
return true;
return false;
}
static inline bool feature_is_dev_test_mode(struct usb_ctrlrequest *crq)
{
if (crq->wValue == cpu_to_le16(USB_DEVICE_TEST_MODE))
return true;
return false;
}
static inline bool feature_is_ep_halt(struct usb_ctrlrequest *crq)
{
if (crq->wValue == cpu_to_le16(USB_ENDPOINT_HALT))
return true;
return false;
}
static int handle_ep0_setup(struct usba_udc *udc, struct usba_ep *ep,
struct usb_ctrlrequest *crq)
{
int retval = 0;
switch (crq->bRequest) {
case USB_REQ_GET_STATUS: {
u16 status;
if (crq->bRequestType == (USB_DIR_IN | USB_RECIP_DEVICE)) {
status = cpu_to_le16(udc->devstatus);
} else if (crq->bRequestType
== (USB_DIR_IN | USB_RECIP_INTERFACE)) {
status = cpu_to_le16(0);
} else if (crq->bRequestType
== (USB_DIR_IN | USB_RECIP_ENDPOINT)) {
struct usba_ep *target;
target = get_ep_by_addr(udc, le16_to_cpu(crq->wIndex));
if (!target)
goto stall;
status = 0;
if (is_stalled(udc, target))
status |= cpu_to_le16(1);
} else {
goto delegate;
}
/* Write directly to the FIFO. No queueing is done. */
if (crq->wLength != cpu_to_le16(sizeof(status)))
goto stall;
ep->state = DATA_STAGE_IN;
__raw_writew(status, ep->fifo);
usba_ep_writel(ep, SET_STA, USBA_TX_PK_RDY);
break;
}
case USB_REQ_CLEAR_FEATURE: {
if (crq->bRequestType == USB_RECIP_DEVICE) {
if (feature_is_dev_remote_wakeup(crq))
udc->devstatus
&= ~(1 << USB_DEVICE_REMOTE_WAKEUP);
else
/* Can't CLEAR_FEATURE TEST_MODE */
goto stall;
} else if (crq->bRequestType == USB_RECIP_ENDPOINT) {
struct usba_ep *target;
if (crq->wLength != cpu_to_le16(0) ||
!feature_is_ep_halt(crq))
goto stall;
target = get_ep_by_addr(udc, le16_to_cpu(crq->wIndex));
if (!target)
goto stall;
usba_ep_writel(target, CLR_STA, USBA_FORCE_STALL);
if (target->index != 0)
usba_ep_writel(target, CLR_STA,
USBA_TOGGLE_CLR);
} else {
goto delegate;
}
send_status(udc, ep);
break;
}
case USB_REQ_SET_FEATURE: {
if (crq->bRequestType == USB_RECIP_DEVICE) {
if (feature_is_dev_test_mode(crq)) {
send_status(udc, ep);
ep->state = STATUS_STAGE_TEST;
udc->test_mode = le16_to_cpu(crq->wIndex);
return 0;
} else if (feature_is_dev_remote_wakeup(crq)) {
udc->devstatus |= 1 << USB_DEVICE_REMOTE_WAKEUP;
} else {
goto stall;
}
} else if (crq->bRequestType == USB_RECIP_ENDPOINT) {
struct usba_ep *target;
if (crq->wLength != cpu_to_le16(0) ||
!feature_is_ep_halt(crq))
goto stall;
target = get_ep_by_addr(udc, le16_to_cpu(crq->wIndex));
if (!target)
goto stall;
usba_ep_writel(target, SET_STA, USBA_FORCE_STALL);
} else {
goto delegate;
}
send_status(udc, ep);
break;
}
case USB_REQ_SET_ADDRESS:
if (crq->bRequestType != (USB_DIR_OUT | USB_RECIP_DEVICE))
goto delegate;
set_address(udc, le16_to_cpu(crq->wValue));
send_status(udc, ep);
ep->state = STATUS_STAGE_ADDR;
break;
default:
delegate:
spin_unlock(&udc->lock);
retval = udc->driver->setup(&udc->gadget, crq);
spin_lock(&udc->lock);
}
return retval;
stall:
DBG(DBG_ALL, "%s: Invalid setup request: %02x.%02x v%04x i%04x l%d\n",
ep->ep.name, crq->bRequestType, crq->bRequest,
le16_to_cpu(crq->wValue), le16_to_cpu(crq->wIndex),
le16_to_cpu(crq->wLength));
set_protocol_stall(udc, ep);
return -1;
}
static void usba_control_irq(struct usba_udc *udc, struct usba_ep *ep)
{
struct usba_request *req;
u32 epstatus;
u32 epctrl;
restart:
epstatus = usba_ep_readl(ep, STA);
epctrl = usba_ep_readl(ep, CTL);
DBG(DBG_INT, "%s [%d]: s/%08x c/%08x\n",
ep->ep.name, ep->state, epstatus, epctrl);
req = NULL;
if (!list_empty(&ep->queue))
req = list_entry(ep->queue.next,
struct usba_request, queue);
if ((epctrl & USBA_TX_PK_RDY) && !(epstatus & USBA_TX_PK_RDY)) {
if (req->submitted)
next_fifo_transaction(ep, req);
else
submit_request(ep, req);
if (req->last_transaction) {
usba_ep_writel(ep, CTL_DIS, USBA_TX_PK_RDY);
usba_ep_writel(ep, CTL_ENB, USBA_TX_COMPLETE);
}
goto restart;
}
if ((epstatus & epctrl) & USBA_TX_COMPLETE) {
usba_ep_writel(ep, CLR_STA, USBA_TX_COMPLETE);
switch (ep->state) {
case DATA_STAGE_IN:
usba_ep_writel(ep, CTL_ENB, USBA_RX_BK_RDY);
usba_ep_writel(ep, CTL_DIS, USBA_TX_COMPLETE);
ep->state = STATUS_STAGE_OUT;
break;
case STATUS_STAGE_ADDR:
/* Activate our new address */
usba_writel(udc, CTRL, (usba_readl(udc, CTRL)
| USBA_FADDR_EN));
usba_ep_writel(ep, CTL_DIS, USBA_TX_COMPLETE);
ep->state = WAIT_FOR_SETUP;
break;
case STATUS_STAGE_IN:
if (req) {
list_del_init(&req->queue);
request_complete(ep, req, 0);
submit_next_request(ep);
}
usba_ep_writel(ep, CTL_DIS, USBA_TX_COMPLETE);
ep->state = WAIT_FOR_SETUP;
break;
case STATUS_STAGE_TEST:
usba_ep_writel(ep, CTL_DIS, USBA_TX_COMPLETE);
ep->state = WAIT_FOR_SETUP;
if (do_test_mode(udc))
set_protocol_stall(udc, ep);
break;
default:
DBG(DBG_ALL, "%s: TXCOMP: Invalid endpoint state %d\n",
ep->ep.name, ep->state);
set_protocol_stall(udc, ep);
break;
}
goto restart;
}
if ((epstatus & epctrl) & USBA_RX_BK_RDY) {
switch (ep->state) {
case STATUS_STAGE_OUT:
usba_ep_writel(ep, CLR_STA, USBA_RX_BK_RDY);
usba_ep_writel(ep, CTL_DIS, USBA_RX_BK_RDY);
if (req) {
list_del_init(&req->queue);
request_complete(ep, req, 0);
}
ep->state = WAIT_FOR_SETUP;
break;
case DATA_STAGE_OUT:
receive_data(ep);
break;
default:
usba_ep_writel(ep, CLR_STA, USBA_RX_BK_RDY);
usba_ep_writel(ep, CTL_DIS, USBA_RX_BK_RDY);
DBG(DBG_ALL, "%s: RXRDY: Invalid endpoint state %d\n",
ep->ep.name, ep->state);
set_protocol_stall(udc, ep);
break;
}
goto restart;
}
if (epstatus & USBA_RX_SETUP) {
union {
struct usb_ctrlrequest crq;
unsigned long data[2];
} crq;
unsigned int pkt_len;
int ret;
if (ep->state != WAIT_FOR_SETUP) {
/*
* Didn't expect a SETUP packet at this
* point. Clean up any pending requests (which
* may be successful).
*/
int status = -EPROTO;
/*
* RXRDY and TXCOMP are dropped when SETUP
* packets arrive. Just pretend we received
* the status packet.
*/
if (ep->state == STATUS_STAGE_OUT ||
ep->state == STATUS_STAGE_IN) {
usba_ep_writel(ep, CTL_DIS, USBA_RX_BK_RDY);
status = 0;
}
if (req) {
list_del_init(&req->queue);
request_complete(ep, req, status);
}
}
pkt_len = USBA_BFEXT(BYTE_COUNT, usba_ep_readl(ep, STA));
DBG(DBG_HW, "Packet length: %u\n", pkt_len);
if (pkt_len != sizeof(crq)) {
DBG(DBG_ALL, "udc: Invalid length %u (expected %zu)\n",
pkt_len, sizeof(crq));
set_protocol_stall(udc, ep);
return;
}
DBG(DBG_FIFO, "Copying ctrl request from 0x%p:\n", ep->fifo);
memcpy(crq.data, ep->fifo, sizeof(crq));
/* Free up one bank in the FIFO so that we can
* generate or receive a reply right away. */
usba_ep_writel(ep, CLR_STA, USBA_RX_SETUP);
if (crq.crq.bRequestType & USB_DIR_IN) {
/*
* The USB 2.0 spec states that "if wLength is
* zero, there is no data transfer phase."
* However, testusb #14 seems to actually
* expect a data phase even if wLength = 0...
*/
ep->state = DATA_STAGE_IN;
} else {
if (crq.crq.wLength != cpu_to_le16(0))
ep->state = DATA_STAGE_OUT;
else
ep->state = STATUS_STAGE_IN;
}
ret = -1;
if (ep->index == 0) {
ret = handle_ep0_setup(udc, ep, &crq.crq);
} else {
spin_unlock(&udc->lock);
ret = udc->driver->setup(&udc->gadget, &crq.crq);
spin_lock(&udc->lock);
}
DBG(DBG_BUS, "req %02x.%02x, length %d, state %d, ret %d\n",
crq.crq.bRequestType, crq.crq.bRequest,
le16_to_cpu(crq.crq.wLength), ep->state, ret);
if (ret < 0) {
/* Let the host know that we failed */
set_protocol_stall(udc, ep);
}
}
}
static void usba_ep_irq(struct usba_udc *udc, struct usba_ep *ep)
{
struct usba_request *req;
u32 epstatus;
u32 epctrl;
epstatus = usba_ep_readl(ep, STA);
epctrl = usba_ep_readl(ep, CTL);
DBG(DBG_INT, "%s: interrupt, status: 0x%08x\n", ep->ep.name, epstatus);
while ((epctrl & USBA_TX_PK_RDY) && !(epstatus & USBA_TX_PK_RDY)) {
DBG(DBG_BUS, "%s: TX PK ready\n", ep->ep.name);
if (list_empty(&ep->queue)) {
DBG(DBG_INT, "ep_irq: queue empty\n");
usba_ep_writel(ep, CTL_DIS, USBA_TX_PK_RDY);
return;
}
req = list_entry(ep->queue.next, struct usba_request, queue);
if (req->submitted)
next_fifo_transaction(ep, req);
else
submit_request(ep, req);
if (req->last_transaction) {
list_del_init(&req->queue);
submit_next_request(ep);
request_complete(ep, req, 0);
}
epstatus = usba_ep_readl(ep, STA);
epctrl = usba_ep_readl(ep, CTL);
}
if ((epstatus & epctrl) & USBA_RX_BK_RDY) {
DBG(DBG_BUS, "%s: RX data ready\n", ep->ep.name);
receive_data(ep);
}
}
static int usba_udc_irq(struct usba_udc *udc)
{
u32 status, ep_status;
spin_lock(&udc->lock);
status = usba_readl(udc, INT_STA);
DBG(DBG_INT, "irq, status=%#08x\n", status);
if (status & USBA_DET_SUSPEND) {
usba_writel(udc, INT_CLR, USBA_DET_SUSPEND);
DBG(DBG_BUS, "Suspend detected\n");
if (udc->gadget.speed != USB_SPEED_UNKNOWN &&
udc->driver && udc->driver->suspend) {
spin_unlock(&udc->lock);
udc->driver->suspend(&udc->gadget);
spin_lock(&udc->lock);
}
}
if (status & USBA_WAKE_UP) {
usba_writel(udc, INT_CLR, USBA_WAKE_UP);
DBG(DBG_BUS, "Wake Up CPU detected\n");
}
if (status & USBA_END_OF_RESUME) {
usba_writel(udc, INT_CLR, USBA_END_OF_RESUME);
DBG(DBG_BUS, "Resume detected\n");
if (udc->gadget.speed != USB_SPEED_UNKNOWN &&
udc->driver && udc->driver->resume) {
spin_unlock(&udc->lock);
udc->driver->resume(&udc->gadget);
spin_lock(&udc->lock);
}
}
ep_status = USBA_BFEXT(EPT_INT, status);
if (ep_status) {
int i;
for (i = 0; i < USBA_NR_ENDPOINTS; i++)
if (ep_status & (1 << i)) {
if (ep_is_control(&udc->usba_ep[i]))
usba_control_irq(udc, &udc->usba_ep[i]);
else
usba_ep_irq(udc, &udc->usba_ep[i]);
}
}
if (status & USBA_END_OF_RESET) {
struct usba_ep *ep0;
usba_writel(udc, INT_CLR, USBA_END_OF_RESET);
reset_all_endpoints(udc);
if (udc->gadget.speed != USB_SPEED_UNKNOWN &&
udc->driver->disconnect) {
udc->gadget.speed = USB_SPEED_UNKNOWN;
spin_unlock(&udc->lock);
udc->driver->disconnect(&udc->gadget);
spin_lock(&udc->lock);
}
if (status & USBA_HIGH_SPEED)
udc->gadget.speed = USB_SPEED_HIGH;
else
udc->gadget.speed = USB_SPEED_FULL;
ep0 = &udc->usba_ep[0];
ep0->desc = &usba_ep0_desc;
ep0->state = WAIT_FOR_SETUP;
usba_ep_writel(ep0, CFG,
(USBA_BF(EPT_SIZE, EP0_EPT_SIZE)
| USBA_BF(EPT_TYPE, USBA_EPT_TYPE_CONTROL)
| USBA_BF(BK_NUMBER, USBA_BK_NUMBER_ONE)));
usba_ep_writel(ep0, CTL_ENB,
USBA_EPT_ENABLE | USBA_RX_SETUP);
usba_writel(udc, INT_ENB,
(usba_readl(udc, INT_ENB)
| USBA_BF(EPT_INT, 1)
| USBA_DET_SUSPEND
| USBA_END_OF_RESUME));
/*
* Unclear why we hit this irregularly, e.g. in usbtest,
* but it's clearly harmless...
*/
if (!(usba_ep_readl(ep0, CFG) & USBA_EPT_MAPPED))
DBG(DBG_ALL, "ODD: EP0 configuration is invalid!\n");
}
spin_unlock(&udc->lock);
return 0;
}
static int atmel_usba_start(struct usba_udc *udc)
{
udc->devstatus = 1 << USB_DEVICE_SELF_POWERED;
udc->vbus_prev = 0;
/* If Vbus is present, enable the controller and wait for reset */
if (vbus_is_present(udc) && udc->vbus_prev == 0) {
usba_writel(udc, CTRL, USBA_ENABLE_MASK);
usba_writel(udc, INT_ENB, USBA_END_OF_RESET);
}
return 0;
}
static int atmel_usba_stop(struct usba_udc *udc)
{
udc->gadget.speed = USB_SPEED_UNKNOWN;
reset_all_endpoints(udc);
/* This will also disable the DP pullup */
usba_writel(udc, CTRL, USBA_DISABLE_MASK);
return 0;
}
static struct usba_udc controller = {
.regs = (unsigned *)ATMEL_BASE_UDPHS,
.fifo = (unsigned *)ATMEL_BASE_UDPHS_FIFO,
.gadget = {
.ops = &usba_udc_ops,
.ep_list = LIST_HEAD_INIT(controller.gadget.ep_list),
.speed = USB_SPEED_HIGH,
.is_dualspeed = 1,
.name = "atmel_usba_udc",
},
};
int usb_gadget_handle_interrupts(int index)
{
struct usba_udc *udc = &controller;
return usba_udc_irq(udc);
}
int usb_gadget_register_driver(struct usb_gadget_driver *driver)
{
struct usba_udc *udc = &controller;
int ret;
if (!driver || !driver->bind || !driver->setup) {
printf("bad paramter\n");
return -EINVAL;
}
if (udc->driver) {
printf("UDC already has a gadget driver\n");
return -EBUSY;
}
atmel_usba_start(udc);
udc->driver = driver;
ret = driver->bind(&udc->gadget);
if (ret) {
pr_err("driver->bind() returned %d\n", ret);
udc->driver = NULL;
}
return ret;
}
int usb_gadget_unregister_driver(struct usb_gadget_driver *driver)
{
struct usba_udc *udc = &controller;
if (!driver || !driver->unbind || !driver->disconnect) {
pr_err("bad paramter\n");
return -EINVAL;
}
driver->disconnect(&udc->gadget);
driver->unbind(&udc->gadget);
udc->driver = NULL;
atmel_usba_stop(udc);
return 0;
}
static struct usba_ep *usba_udc_pdata(struct usba_platform_data *pdata,
struct usba_udc *udc)
{
struct usba_ep *eps;
int i;
eps = malloc(sizeof(struct usba_ep) * pdata->num_ep);
if (!eps) {
pr_err("failed to alloc eps\n");
return NULL;
}
udc->gadget.ep0 = &eps[0].ep;
INIT_LIST_HEAD(&udc->gadget.ep_list);
INIT_LIST_HEAD(&eps[0].ep.ep_list);
for (i = 0; i < pdata->num_ep; i++) {
struct usba_ep *ep = &eps[i];
ep->ep_regs = udc->regs + USBA_EPT_BASE(i);
ep->dma_regs = udc->regs + USBA_DMA_BASE(i);
ep->fifo = udc->fifo + USBA_FIFO_BASE(i);
ep->ep.ops = &usba_ep_ops;
ep->ep.name = pdata->ep[i].name;
ep->ep.maxpacket = pdata->ep[i].fifo_size;
ep->fifo_size = ep->ep.maxpacket;
ep->udc = udc;
INIT_LIST_HEAD(&ep->queue);
ep->nr_banks = pdata->ep[i].nr_banks;
ep->index = pdata->ep[i].index;
ep->can_dma = pdata->ep[i].can_dma;
ep->can_isoc = pdata->ep[i].can_isoc;
if (i)
list_add_tail(&ep->ep.ep_list, &udc->gadget.ep_list);
};
return eps;
}
int usba_udc_probe(struct usba_platform_data *pdata)
{
struct usba_udc *udc;
udc = &controller;
udc->usba_ep = usba_udc_pdata(pdata, udc);
return 0;
}