| /* |
| * Copyright (C) ST-Ericsson SA 2009 |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| #ifndef _U8500_I2C_H_ |
| #define _U8500_I2C_H_ |
| |
| #include <asm/types.h> |
| #include <asm/io.h> |
| #include <asm/errno.h> |
| #include <asm/arch/u8500.h> |
| |
| struct u8500_i2c_regs { |
| u32 cr; /* Control Register 0x00 */ |
| u32 scr; /* Slave Address Register 0x04 */ |
| u32 hsmcr; /* HS Master code Register 0x08 */ |
| u32 mcr; /* Master Control Register 0x0C */ |
| u32 tfr; /* Transmit Fifo Register 0x10 */ |
| u32 sr; /* Status Register 0x14 */ |
| u32 rfr; /* Receiver Fifo Register 0x18 */ |
| u32 tftr; /* Transmit Fifo Threshold Register 0x1C */ |
| u32 rftr; /* Receiver Fifo Threshold Register 0x20 */ |
| u32 dmar; /* DMA register 0x24 */ |
| u32 brcr; /* Baud Rate Counter Register 0x28 */ |
| u32 imscr; /* Interrupt Mask Set and Clear Register 0x2C */ |
| u32 risr; /* Raw interrupt status register 0x30 */ |
| u32 misr; /* Masked interrupt status register 0x34 */ |
| u32 icr; /* Interrupt Set and Clear Register 0x38 */ |
| u32 reserved_1[(0xFE0 - 0x3c) >> 2]; /* Reserved 0x03C to 0xFE0 */ |
| u32 periph_id_0; /* peripheral ID 0 0xFE0 */ |
| u32 periph_id_1; /* peripheral ID 1 0xFE4 */ |
| u32 periph_id_2; /* peripheral ID 2 0xFE8 */ |
| u32 periph_id_3; /* peripheral ID 3 0xFEC */ |
| u32 cell_id_0; /* I2C cell ID 0 0xFF0 */ |
| u32 cell_id_1; /* I2C cell ID 1 0xFF4 */ |
| u32 cell_id_2; /* I2C cell ID 2 0xFF8 */ |
| u32 cell_id_3; /* I2C cell ID 3 0xFFC */ |
| }; |
| |
| |
| /* Control Register */ |
| |
| /* Mask values for control register mask */ |
| #define U8500_I2C_CR_PE 0x0001 /* Peripheral enable */ |
| #define U8500_I2C_CR_OM 0x0006 /* Operation mode */ |
| #define U8500_I2C_CR_SAM 0x0008 /* Slave Addressing mode */ |
| #define U8500_I2C_CR_SM 0x0030 /* Speed mode */ |
| #define U8500_I2C_CR_SGCM 0x0040 /* Slave General call mode */ |
| #define U8500_I2C_CR_FTX 0x0080 /* Flush Transmit */ |
| #define U8500_I2C_CR_FRX 0x0100 /* Flush Receive */ |
| #define U8500_I2C_CR_DMA_TX_EN 0x0200 /* DMA TX Enable */ |
| #define U8500_I2C_CR_DMA_RX_EN 0x0400 /* DMA Rx Enable */ |
| #define U8500_I2C_CR_DMA_SLE 0x0800 /* DMA Synchronization Logic enable */ |
| #define U8500_I2C_CR_LM 0x1000 /* Loop back mode */ |
| #define U8500_I2C_CR_FON 0x6000 /* Filtering On */ |
| |
| /* shift valus for control register bit fields */ |
| #define U8500_I2C_CR_SHIFT_PE 0 /* Peripheral enable */ |
| #define U8500_I2C_CR_SHIFT_OM 1 /* Operation mode */ |
| #define U8500_I2C_CR_SHIFT_SAM 3 /* Slave Addressing mode */ |
| #define U8500_I2C_CR_SHIFT_SM 4 /* Speed mode */ |
| #define U8500_I2C_CR_SHIFT_SGCM 6 /* Slave General call mode */ |
| #define U8500_I2C_CR_SHIFT_FTX 7 /* Flush Transmit */ |
| #define U8500_I2C_CR_SHIFT_FRX 8 /* Flush Receive */ |
| #define U8500_I2C_CR_SHIFT_DMA_TX_EN 9 /* DMA TX Enable */ |
| #define U8500_I2C_CR_SHIFT_DMA_RX_EN 10 /* DMA Rx Enable */ |
| #define U8500_I2C_CR_SHIFT_DMA_SLE 11 /* DMA Synch Logic enable */ |
| #define U8500_I2C_CR_SHIFT_LM 12 /* Loop back mode */ |
| #define U8500_I2C_CR_SHIFT_FON 13 /* Filtering On */ |
| |
| /* bus operation modes */ |
| #define U8500_I2C_BUS_SLAVE_MODE 0 |
| #define U8500_I2C_BUS_MASTER_MODE 1 |
| #define U8500_I2C_BUS_MASTER_SLAVE_MODE 2 |
| |
| |
| /* Slave control register*/ |
| |
| /* Mask values slave control register */ |
| #define U8500_I2C_SCR_ADDR 0x3FF |
| #define U8500_I2C_SCR_DATA_SETUP_TIME 0xFFFF0000 |
| |
| /* Shift values for Slave control register */ |
| #define U8500_I2C_SCR_SHIFT_ADDR 0 |
| #define U8500_I2C_SCR_SHIFT_DATA_SETUP_TIME 16 |
| |
| |
| /* Master Control Register */ |
| |
| /* Mask values for Master control register */ |
| #define U8500_I2C_MCR_OP 0x00000001 /* Operation */ |
| #define U8500_I2C_MCR_A7 0x000000FE /* LSB bits of Address */ |
| #define U8500_I2C_MCR_EA10 0x00000700 /* Extended Address */ |
| #define U8500_I2C_MCR_SB 0x00000800 /* Start byte procedure */ |
| #define U8500_I2C_MCR_AM 0x00003000 /* Address type */ |
| #define U8500_I2C_MCR_STOP 0x00004000 /* stop condition */ |
| #define U8500_I2C_MCR_LENGTH 0x03FF8000 /* Frame length */ |
| #define U8500_I2C_MCR_A10 0x000007FE /* Enable 10 bit address */ |
| /* mask for length field,stop and operation */ |
| #define U8500_I2C_MCR_LENGTH_STOP_OP 0x3FFC001 |
| |
| /* Shift values for Master control values */ |
| #define U8500_I2C_MCR_SHIFT_OP 0 /* Operation */ |
| #define U8500_I2C_MCR_SHIFT_A7 1 /* LSB bits of Address */ |
| #define U8500_I2C_MCR_SHIFT_EA10 8 /* Extended Address */ |
| #define U8500_I2C_MCR_SHIFT_SB 11 /* Start byte procedure */ |
| #define U8500_I2C_MCR_SHIFT_AM 12 /* Address type */ |
| #define U8500_I2C_MCR_SHIFT_STOP 14 /* stop condition */ |
| #define U8500_I2C_MCR_SHIFT_LENGTH 15 /* Frame length */ |
| #define U8500_I2C_MCR_SHIFT_A10 1 /* Enable 10 bit address */ |
| |
| #define U8500_I2C_MCR_SHIFT_LENGTH_STOP_OP 0 |
| |
| |
| /* Status Register */ |
| |
| /* Mask values for Status register */ |
| #define U8500_I2C_SR_OP 0x00000003 /* Operation */ |
| #define U8500_I2C_SR_STATUS 0x0000000C /* Controller Status */ |
| #define U8500_I2C_SR_CAUSE 0x00000070 /* Abort Cause */ |
| #define U8500_I2C_SR_TYPE 0x00000180 /* Receive Type */ |
| #define U8500_I2C_SR_LENGTH 0x000FF700 /* Transfer length */ |
| |
| /* Shift values for Status register */ |
| #define U8500_I2C_SR_SHIFT_OP 0 /* Operation */ |
| #define U8500_I2C_SR_SHIFT_STATUS 2 /* Controller Status */ |
| #define U8500_I2C_SR_SHIFT_CAUSE 4 /* Abort Cause */ |
| #define U8500_I2C_SR_SHIFT_TYPE 7 /* Receive Type */ |
| #define U8500_I2C_SR_SHIFT_LENGTH 9 /* Transfer length */ |
| |
| /* abort cause */ |
| #define U8500_I2C_NACK_ADDR 0 |
| #define U8500_I2C_NACK_DATA 1 |
| #define U8500_I2C_ACK_MCODE 2 |
| #define U8500_I2C_ARB_LOST 3 |
| #define U8500_I2C_BERR_START 4 |
| #define U8500_I2C_BERR_STOP 5 |
| #define U8500_I2C_OVFL 6 |
| |
| |
| /* Baud rate counter registers */ |
| |
| /* Mask values for Baud rate counter register */ |
| #define U8500_I2C_BRCR_BRCNT2 0xFFFF /* Baud Rate Cntr BRCR for HS */ |
| #define U8500_I2C_BRCR_BRCNT1 0xFFFF0000 /* BRCR for Standard and Fast */ |
| |
| /* Shift values for the Baud rate counter register */ |
| #define U8500_I2C_BRCR_SHIFT_BRCNT2 0 |
| #define U8500_I2C_BRCR_SHIFT_BRCNT1 16 |
| |
| |
| /* Interrupt Register */ |
| |
| /* Mask values for Interrupt registers */ |
| #define U8500_I2C_INT_TXFE 0x00000001 /* Tx fifo empty */ |
| #define U8500_I2C_INT_TXFNE 0x00000002 /* Tx Fifo nearly empty */ |
| #define U8500_I2C_INT_TXFF 0x00000004 /* Tx Fifo Full */ |
| #define U8500_I2C_INT_TXFOVR 0x00000008 /* Tx Fifo over run */ |
| #define U8500_I2C_INT_RXFE 0x00000010 /* Rx Fifo Empty */ |
| #define U8500_I2C_INT_RXFNF 0x00000020 /* Rx Fifo nearly empty */ |
| #define U8500_I2C_INT_RXFF 0x00000040 /* Rx Fifo Full */ |
| #define U8500_I2C_INT_RFSR 0x00010000 /* Read From slave request */ |
| #define U8500_I2C_INT_RFSE 0x00020000 /* Read from slave empty */ |
| #define U8500_I2C_INT_WTSR 0x00040000 /* Write to Slave request */ |
| #define U8500_I2C_INT_MTD 0x00080000 /* Master Transcation Done*/ |
| #define U8500_I2C_INT_STD 0x00100000 /* Slave Transaction Done */ |
| #define U8500_I2C_INT_MAL 0x01000000 /* Master Arbitation Lost */ |
| #define U8500_I2C_INT_BERR 0x02000000 /* Bus Error */ |
| #define U8500_I2C_INT_MTDWS 0x10000000 /* Master Tran Done wo/ Stop */ |
| |
| /* Max clocks (Hz) */ |
| #define U8500_I2C_MAX_STANDARD_SCL 100000 |
| #define U8500_I2C_MAX_FAST_SCL 400000 |
| #define U8500_I2C_MAX_HIGH_SPEED_SCL 3400000 |
| |
| #endif /* _U8500_I2C_H_ */ |