| /* |
| * Copyright 2008 Freescale Semiconductor, Inc. |
| * |
| * This program is free software; you can redistribute it and/or |
| * modify it under the terms of the GNU General Public License |
| * Version 2 as published by the Free Software Foundation. |
| */ |
| |
| #ifndef _DDR_SPD_H_ |
| #define _DDR_SPD_H_ |
| |
| /* |
| * Format from "JEDEC Standard No. 21-C, |
| * Appendix D: Rev 1.0: SPD's for DDR SDRAM |
| */ |
| typedef struct ddr1_spd_eeprom_s { |
| unsigned char info_size; /* 0 # bytes written into serial memory */ |
| unsigned char chip_size; /* 1 Total # bytes of SPD memory device */ |
| unsigned char mem_type; /* 2 Fundamental memory type */ |
| unsigned char nrow_addr; /* 3 # of Row Addresses on this assembly */ |
| unsigned char ncol_addr; /* 4 # of Column Addrs on this assembly */ |
| unsigned char nrows; /* 5 Number of DIMM Banks */ |
| unsigned char dataw_lsb; /* 6 Data Width of this assembly */ |
| unsigned char dataw_msb; /* 7 ... Data Width continuation */ |
| unsigned char voltage; /* 8 Voltage intf std of this assembly */ |
| unsigned char clk_cycle; /* 9 SDRAM Cycle time @ CL=X */ |
| unsigned char clk_access; /* 10 SDRAM Access from Clk @ CL=X (tAC) */ |
| unsigned char config; /* 11 DIMM Configuration type */ |
| unsigned char refresh; /* 12 Refresh Rate/Type */ |
| unsigned char primw; /* 13 Primary SDRAM Width */ |
| unsigned char ecw; /* 14 Error Checking SDRAM width */ |
| unsigned char min_delay; /* 15 for Back to Back Random Address */ |
| unsigned char burstl; /* 16 Burst Lengths Supported */ |
| unsigned char nbanks; /* 17 # of Banks on SDRAM Device */ |
| unsigned char cas_lat; /* 18 CAS# Latencies Supported */ |
| unsigned char cs_lat; /* 19 CS# Latency */ |
| unsigned char write_lat; /* 20 Write Latency (aka Write Recovery) */ |
| unsigned char mod_attr; /* 21 SDRAM Module Attributes */ |
| unsigned char dev_attr; /* 22 SDRAM Device Attributes */ |
| unsigned char clk_cycle2; /* 23 Min SDRAM Cycle time @ CL=X-0.5 */ |
| unsigned char clk_access2; /* 24 SDRAM Access from |
| Clk @ CL=X-0.5 (tAC) */ |
| unsigned char clk_cycle3; /* 25 Min SDRAM Cycle time @ CL=X-1 */ |
| unsigned char clk_access3; /* 26 Max Access from Clk @ CL=X-1 (tAC) */ |
| unsigned char trp; /* 27 Min Row Precharge Time (tRP)*/ |
| unsigned char trrd; /* 28 Min Row Active to Row Active (tRRD) */ |
| unsigned char trcd; /* 29 Min RAS to CAS Delay (tRCD) */ |
| unsigned char tras; /* 30 Minimum RAS Pulse Width (tRAS) */ |
| unsigned char bank_dens; /* 31 Density of each bank on module */ |
| unsigned char ca_setup; /* 32 Addr + Cmd Setup Time Before Clk */ |
| unsigned char ca_hold; /* 33 Addr + Cmd Hold Time After Clk */ |
| unsigned char data_setup; /* 34 Data Input Setup Time Before Strobe */ |
| unsigned char data_hold; /* 35 Data Input Hold Time After Strobe */ |
| unsigned char res_36_40[5];/* 36-40 reserved for VCSDRAM */ |
| unsigned char trc; /* 41 Min Active to Auto refresh time tRC */ |
| unsigned char trfc; /* 42 Min Auto to Active period tRFC */ |
| unsigned char tckmax; /* 43 Max device cycle time tCKmax */ |
| unsigned char tdqsq; /* 44 Max DQS to DQ skew (tDQSQ max) */ |
| unsigned char tqhs; /* 45 Max Read DataHold skew (tQHS) */ |
| unsigned char res_46; /* 46 Reserved */ |
| unsigned char dimm_height; /* 47 DDR SDRAM DIMM Height */ |
| unsigned char res_48_61[14]; /* 48-61 Reserved */ |
| unsigned char spd_rev; /* 62 SPD Data Revision Code */ |
| unsigned char cksum; /* 63 Checksum for bytes 0-62 */ |
| unsigned char mid[8]; /* 64-71 Mfr's JEDEC ID code per JEP-106 */ |
| unsigned char mloc; /* 72 Manufacturing Location */ |
| unsigned char mpart[18]; /* 73 Manufacturer's Part Number */ |
| unsigned char rev[2]; /* 91 Revision Code */ |
| unsigned char mdate[2]; /* 93 Manufacturing Date */ |
| unsigned char sernum[4]; /* 95 Assembly Serial Number */ |
| unsigned char mspec[27]; /* 99-127 Manufacturer Specific Data */ |
| |
| } ddr1_spd_eeprom_t; |
| |
| /* |
| * Format from "JEDEC Appendix X: Serial Presence Detects for DDR2 SDRAM", |
| * SPD Revision 1.2 |
| */ |
| typedef struct ddr2_spd_eeprom_s { |
| unsigned char info_size; /* 0 # bytes written into serial memory */ |
| unsigned char chip_size; /* 1 Total # bytes of SPD memory device */ |
| unsigned char mem_type; /* 2 Fundamental memory type */ |
| unsigned char nrow_addr; /* 3 # of Row Addresses on this assembly */ |
| unsigned char ncol_addr; /* 4 # of Column Addrs on this assembly */ |
| unsigned char mod_ranks; /* 5 Number of DIMM Ranks */ |
| unsigned char dataw; /* 6 Module Data Width */ |
| unsigned char res_7; /* 7 Reserved */ |
| unsigned char voltage; /* 8 Voltage intf std of this assembly */ |
| unsigned char clk_cycle; /* 9 SDRAM Cycle time @ CL=X */ |
| unsigned char clk_access; /* 10 SDRAM Access from Clk @ CL=X (tAC) */ |
| unsigned char config; /* 11 DIMM Configuration type */ |
| unsigned char refresh; /* 12 Refresh Rate/Type */ |
| unsigned char primw; /* 13 Primary SDRAM Width */ |
| unsigned char ecw; /* 14 Error Checking SDRAM width */ |
| unsigned char res_15; /* 15 Reserved */ |
| unsigned char burstl; /* 16 Burst Lengths Supported */ |
| unsigned char nbanks; /* 17 # of Banks on Each SDRAM Device */ |
| unsigned char cas_lat; /* 18 CAS# Latencies Supported */ |
| unsigned char mech_char; /* 19 DIMM Mechanical Characteristics */ |
| unsigned char dimm_type; /* 20 DIMM type information */ |
| unsigned char mod_attr; /* 21 SDRAM Module Attributes */ |
| unsigned char dev_attr; /* 22 SDRAM Device Attributes */ |
| unsigned char clk_cycle2; /* 23 Min SDRAM Cycle time @ CL=X-1 */ |
| unsigned char clk_access2; /* 24 SDRAM Access from Clk @ CL=X-1 (tAC) */ |
| unsigned char clk_cycle3; /* 25 Min SDRAM Cycle time @ CL=X-2 */ |
| unsigned char clk_access3; /* 26 Max Access from Clk @ CL=X-2 (tAC) */ |
| unsigned char trp; /* 27 Min Row Precharge Time (tRP)*/ |
| unsigned char trrd; /* 28 Min Row Active to Row Active (tRRD) */ |
| unsigned char trcd; /* 29 Min RAS to CAS Delay (tRCD) */ |
| unsigned char tras; /* 30 Minimum RAS Pulse Width (tRAS) */ |
| unsigned char rank_dens; /* 31 Density of each rank on module */ |
| unsigned char ca_setup; /* 32 Addr+Cmd Setup Time Before Clk (tIS) */ |
| unsigned char ca_hold; /* 33 Addr+Cmd Hold Time After Clk (tIH) */ |
| unsigned char data_setup; /* 34 Data Input Setup Time |
| Before Strobe (tDS) */ |
| unsigned char data_hold; /* 35 Data Input Hold Time |
| After Strobe (tDH) */ |
| unsigned char twr; /* 36 Write Recovery time tWR */ |
| unsigned char twtr; /* 37 Int write to read delay tWTR */ |
| unsigned char trtp; /* 38 Int read to precharge delay tRTP */ |
| unsigned char mem_probe; /* 39 Mem analysis probe characteristics */ |
| unsigned char trctrfc_ext; /* 40 Extensions to trc and trfc */ |
| unsigned char trc; /* 41 Min Active to Auto refresh time tRC */ |
| unsigned char trfc; /* 42 Min Auto to Active period tRFC */ |
| unsigned char tckmax; /* 43 Max device cycle time tCKmax */ |
| unsigned char tdqsq; /* 44 Max DQS to DQ skew (tDQSQ max) */ |
| unsigned char tqhs; /* 45 Max Read DataHold skew (tQHS) */ |
| unsigned char pll_relock; /* 46 PLL Relock time */ |
| unsigned char Tcasemax; /* 47 Tcasemax */ |
| unsigned char psiTAdram; /* 48 Thermal Resistance of DRAM Package from |
| Top (Case) to Ambient (Psi T-A DRAM) */ |
| unsigned char dt0_mode; /* 49 DRAM Case Temperature Rise from Ambient |
| due to Activate-Precharge/Mode Bits |
| (DT0/Mode Bits) */ |
| unsigned char dt2n_dt2q; /* 50 DRAM Case Temperature Rise from Ambient |
| due to Precharge/Quiet Standby |
| (DT2N/DT2Q) */ |
| unsigned char dt2p; /* 51 DRAM Case Temperature Rise from Ambient |
| due to Precharge Power-Down (DT2P) */ |
| unsigned char dt3n; /* 52 DRAM Case Temperature Rise from Ambient |
| due to Active Standby (DT3N) */ |
| unsigned char dt3pfast; /* 53 DRAM Case Temperature Rise from Ambient |
| due to Active Power-Down with |
| Fast PDN Exit (DT3Pfast) */ |
| unsigned char dt3pslow; /* 54 DRAM Case Temperature Rise from Ambient |
| due to Active Power-Down with Slow |
| PDN Exit (DT3Pslow) */ |
| unsigned char dt4r_dt4r4w; /* 55 DRAM Case Temperature Rise from Ambient |
| due to Page Open Burst Read/DT4R4W |
| Mode Bit (DT4R/DT4R4W Mode Bit) */ |
| unsigned char dt5b; /* 56 DRAM Case Temperature Rise from Ambient |
| due to Burst Refresh (DT5B) */ |
| unsigned char dt7; /* 57 DRAM Case Temperature Rise from Ambient |
| due to Bank Interleave Reads with |
| Auto-Precharge (DT7) */ |
| unsigned char psiTApll; /* 58 Thermal Resistance of PLL Package form |
| Top (Case) to Ambient (Psi T-A PLL) */ |
| unsigned char psiTAreg; /* 59 Thermal Reisitance of Register Package |
| from Top (Case) to Ambient |
| (Psi T-A Register) */ |
| unsigned char dtpllactive; /* 60 PLL Case Temperature Rise from Ambient |
| due to PLL Active (DT PLL Active) */ |
| unsigned char dtregact; /* 61 Register Case Temperature Rise from |
| Ambient due to Register Active/Mode Bit |
| (DT Register Active/Mode Bit) */ |
| unsigned char spd_rev; /* 62 SPD Data Revision Code */ |
| unsigned char cksum; /* 63 Checksum for bytes 0-62 */ |
| unsigned char mid[8]; /* 64 Mfr's JEDEC ID code per JEP-106 */ |
| unsigned char mloc; /* 72 Manufacturing Location */ |
| unsigned char mpart[18]; /* 73 Manufacturer's Part Number */ |
| unsigned char rev[2]; /* 91 Revision Code */ |
| unsigned char mdate[2]; /* 93 Manufacturing Date */ |
| unsigned char sernum[4]; /* 95 Assembly Serial Number */ |
| unsigned char mspec[27]; /* 99-127 Manufacturer Specific Data */ |
| |
| } ddr2_spd_eeprom_t; |
| |
| typedef struct ddr3_spd_eeprom_s { |
| /* General Section: Bytes 0-59 */ |
| unsigned char info_size_crc; /* 0 # bytes written into serial memory, |
| CRC coverage */ |
| unsigned char spd_rev; /* 1 Total # bytes of SPD mem device */ |
| unsigned char mem_type; /* 2 Key Byte / Fundamental mem type */ |
| unsigned char module_type; /* 3 Key Byte / Module Type */ |
| unsigned char density_banks; /* 4 SDRAM Density and Banks */ |
| unsigned char addressing; /* 5 SDRAM Addressing */ |
| unsigned char module_vdd; /* 6 Module nominal voltage, VDD */ |
| unsigned char organization; /* 7 Module Organization */ |
| unsigned char bus_width; /* 8 Module Memory Bus Width */ |
| unsigned char ftb_div; /* 9 Fine Timebase (FTB) |
| Dividend / Divisor */ |
| unsigned char mtb_dividend; /* 10 Medium Timebase (MTB) Dividend */ |
| unsigned char mtb_divisor; /* 11 Medium Timebase (MTB) Divisor */ |
| unsigned char tCK_min; /* 12 SDRAM Minimum Cycle Time */ |
| unsigned char res_13; /* 13 Reserved */ |
| unsigned char caslat_lsb; /* 14 CAS Latencies Supported, |
| Least Significant Byte */ |
| unsigned char caslat_msb; /* 15 CAS Latencies Supported, |
| Most Significant Byte */ |
| unsigned char tAA_min; /* 16 Min CAS Latency Time */ |
| unsigned char tWR_min; /* 17 Min Write REcovery Time */ |
| unsigned char tRCD_min; /* 18 Min RAS# to CAS# Delay Time */ |
| unsigned char tRRD_min; /* 19 Min Row Active to |
| Row Active Delay Time */ |
| unsigned char tRP_min; /* 20 Min Row Precharge Delay Time */ |
| unsigned char tRAS_tRC_ext; /* 21 Upper Nibbles for tRAS and tRC */ |
| unsigned char tRAS_min_lsb; /* 22 Min Active to Precharge |
| Delay Time */ |
| unsigned char tRC_min_lsb; /* 23 Min Active to Active/Refresh |
| Delay Time, LSB */ |
| unsigned char tRFC_min_lsb; /* 24 Min Refresh Recovery Delay Time */ |
| unsigned char tRFC_min_msb; /* 25 Min Refresh Recovery Delay Time */ |
| unsigned char tWTR_min; /* 26 Min Internal Write to |
| Read Command Delay Time */ |
| unsigned char tRTP_min; /* 27 Min Internal Read to Precharge |
| Command Delay Time */ |
| unsigned char tFAW_msb; /* 28 Upper Nibble for tFAW */ |
| unsigned char tFAW_min; /* 29 Min Four Activate Window |
| Delay Time*/ |
| unsigned char opt_features; /* 30 SDRAM Optional Features */ |
| unsigned char therm_ref_opt; /* 31 SDRAM Thermal and Refresh Opts */ |
| unsigned char therm_sensor; /* 32 Module Thermal Sensor */ |
| unsigned char device_type; /* 33 SDRAM device type */ |
| unsigned char res_34_59[26]; /* 34-59 Reserved, General Section */ |
| |
| /* Module-Specific Section: Bytes 60-116 */ |
| union { |
| struct { |
| /* 60 (Unbuffered) Module Nominal Height */ |
| unsigned char mod_height; |
| /* 61 (Unbuffered) Module Maximum Thickness */ |
| unsigned char mod_thickness; |
| /* 62 (Unbuffered) Reference Raw Card Used */ |
| unsigned char ref_raw_card; |
| /* 63 (Unbuffered) Address Mapping from |
| Edge Connector to DRAM */ |
| unsigned char addr_mapping; |
| /* 64-116 (Unbuffered) Reserved */ |
| unsigned char res_64_116[53]; |
| } unbuffered; |
| struct { |
| /* 60 (Registered) Module Nominal Height */ |
| unsigned char mod_height; |
| /* 61 (Registered) Module Maximum Thickness */ |
| unsigned char mod_thickness; |
| /* 62 (Registered) Reference Raw Card Used */ |
| unsigned char ref_raw_card; |
| /* 63 DIMM Module Attributes */ |
| unsigned char modu_attr; |
| /* 64 RDIMM Thermal Heat Spreader Solution */ |
| unsigned char thermal; |
| /* 65 Register Manufacturer ID Code, Least Significant Byte */ |
| unsigned char reg_id_lo; |
| /* 66 Register Manufacturer ID Code, Most Significant Byte */ |
| unsigned char reg_id_hi; |
| /* 67 Register Revision Number */ |
| unsigned char reg_rev; |
| /* 68 Register Type */ |
| unsigned char reg_type; |
| /* 69-76 RC1,3,5...15 (MS Nibble) / RC0,2,4...14 (LS Nibble) */ |
| unsigned char rcw[8]; |
| } registered; |
| unsigned char uc[57]; /* 60-116 Module-Specific Section */ |
| } mod_section; |
| |
| /* Unique Module ID: Bytes 117-125 */ |
| unsigned char mmid_lsb; /* 117 Module MfgID Code LSB - JEP-106 */ |
| unsigned char mmid_msb; /* 118 Module MfgID Code MSB - JEP-106 */ |
| unsigned char mloc; /* 119 Mfg Location */ |
| unsigned char mdate[2]; /* 120-121 Mfg Date */ |
| unsigned char sernum[4]; /* 122-125 Module Serial Number */ |
| |
| /* CRC: Bytes 126-127 */ |
| unsigned char crc[2]; /* 126-127 SPD CRC */ |
| |
| /* Other Manufacturer Fields and User Space: Bytes 128-255 */ |
| unsigned char mpart[18]; /* 128-145 Mfg's Module Part Number */ |
| unsigned char mrev[2]; /* 146-147 Module Revision Code */ |
| |
| unsigned char dmid_lsb; /* 148 DRAM MfgID Code LSB - JEP-106 */ |
| unsigned char dmid_msb; /* 149 DRAM MfgID Code MSB - JEP-106 */ |
| |
| unsigned char msd[26]; /* 150-175 Mfg's Specific Data */ |
| unsigned char cust[80]; /* 176-255 Open for Customer Use */ |
| |
| } ddr3_spd_eeprom_t; |
| |
| extern unsigned int ddr1_spd_check(const ddr1_spd_eeprom_t *spd); |
| extern void ddr1_spd_dump(const ddr1_spd_eeprom_t *spd); |
| extern unsigned int ddr2_spd_check(const ddr2_spd_eeprom_t *spd); |
| extern void ddr2_spd_dump(const ddr2_spd_eeprom_t *spd); |
| extern unsigned int ddr3_spd_check(const ddr3_spd_eeprom_t *spd); |
| |
| /* |
| * Byte 2 Fundamental Memory Types. |
| */ |
| #define SPD_MEMTYPE_FPM (0x01) |
| #define SPD_MEMTYPE_EDO (0x02) |
| #define SPD_MEMTYPE_PIPE_NIBBLE (0x03) |
| #define SPD_MEMTYPE_SDRAM (0x04) |
| #define SPD_MEMTYPE_ROM (0x05) |
| #define SPD_MEMTYPE_SGRAM (0x06) |
| #define SPD_MEMTYPE_DDR (0x07) |
| #define SPD_MEMTYPE_DDR2 (0x08) |
| #define SPD_MEMTYPE_DDR2_FBDIMM (0x09) |
| #define SPD_MEMTYPE_DDR2_FBDIMM_PROBE (0x0A) |
| #define SPD_MEMTYPE_DDR3 (0x0B) |
| |
| /* DIMM Type for DDR2 SPD (according to v1.3) */ |
| #define DDR2_SPD_DIMMTYPE_UNDEFINED (0x00) |
| #define DDR2_SPD_DIMMTYPE_RDIMM (0x01) |
| #define DDR2_SPD_DIMMTYPE_UDIMM (0x02) |
| #define DDR2_SPD_DIMMTYPE_SO_DIMM (0x04) |
| #define DDR2_SPD_DIMMTYPE_72B_SO_CDIMM (0x06) |
| #define DDR2_SPD_DIMMTYPE_72B_SO_RDIMM (0x07) |
| #define DDR2_SPD_DIMMTYPE_MICRO_DIMM (0x08) |
| #define DDR2_SPD_DIMMTYPE_MINI_RDIMM (0x10) |
| #define DDR2_SPD_DIMMTYPE_MINI_UDIMM (0x20) |
| |
| /* Byte 3 Key Byte / Module Type for DDR3 SPD */ |
| #define DDR3_SPD_MODULETYPE_MASK (0x0f) |
| #define DDR3_SPD_MODULETYPE_RDIMM (0x01) |
| #define DDR3_SPD_MODULETYPE_UDIMM (0x02) |
| #define DDR3_SPD_MODULETYPE_SO_DIMM (0x03) |
| #define DDR3_SPD_MODULETYPE_MICRO_DIMM (0x04) |
| #define DDR3_SPD_MODULETYPE_MINI_RDIMM (0x05) |
| #define DDR3_SPD_MODULETYPE_MINI_UDIMM (0x06) |
| |
| #endif /* _DDR_SPD_H_ */ |