| Freescale MPC7448hpc2 (Taiga) board |
| =================================== |
| |
| Created 08/11/2006 Roy Zang |
| -------------------------- |
| MPC7448hpc2 (Taiga) board is a high-performance PowerPC server reference |
| design, which is optimized for high speed throughput between the processor and |
| the memory, disk drive and Ethernet port subsystems. |
| |
| MPC7448hpc2(Taiga) is designed to the micro-ATX chassis, allowing it to be |
| used in 1U or 2U rack-mount chassis¡¯, as well as in standard ATX/Micro-ATX |
| chassis. |
| |
| Building U-Boot |
| ------------------ |
| The mpc7448hpc2 code base is known to compile using: |
| Binutils 2.15, Gcc 3.4.3, Glibc 2.3.3 |
| |
| $ make mpc7448hpc2_config |
| Configuring for mpc7448hpc2 board... |
| |
| $ make |
| |
| Memory Map |
| ---------- |
| |
| The memory map is setup for Linux to operate properly. |
| |
| The mapping is: |
| |
| Range Start Range End Definition Size |
| |
| 0x0000_0000 0x7fff_ffff DDR 2G |
| 0xe000_0000 0xe7ff_ffff PCI Memory 128M |
| 0xfa00_0000 0xfaff_ffff PCI IO 16M |
| 0xfb00_0000 0xfbff_ffff PCI Config 16M |
| 0xfc00_0000 0xfc0f_ffff NVRAM/CADMUS 1M |
| 0xfe00_0000 0xfeff_ffff PromJet 16M |
| 0xff00_0000 0xff80_0000 FLASH (boot flash) 8M |
| 0xff80_0000 0xffff_ffff FLASH (second half flash) 8M |
| |
| Using Flash |
| ----------- |
| |
| The MPC7448hpc2 board has two "banks" of flash, each 8MB in size |
| (2^23 = 0x00800000). |
| |
| Note: the "bank" here refers to half of the flash. In fact, there is only one |
| bank of flash, which is divided into low and high half. Each is controlled by |
| the most significant bit of the address bus. The so called "bank" is only for |
| convenience. |
| |
| There is a switch which allows the "bank" to be selected. The switch |
| settings for updating flash are given below. |
| |
| The u-boot commands for copying the boot-bank into the secondary bank are |
| as follows: |
| |
| erase ff800000 ff880000 |
| cp.b ff000000 ff800000 80000 |
| |
| U-boot commands for downloading an image via tftp and flashing |
| it into the secondary bank: |
| |
| tftp 10000 <u-boot.bin.image> |
| erase ff000000 ff080000 |
| cp.b 10000 ff000000 80000 |
| |
| After copying the image into the second bank of flash, be sure to toggle |
| SW3[4] on board before resetting the board in order to set the |
| secondary bank as the boot-bank. |
| |
| Board Switches |
| ---------------------- |
| |
| Most switches on the board should not be changed. The most frequent |
| user-settable switches on the board are used to configure |
| the flash banks and determining the PCI frequency. |
| |
| SW1[1-5]: Processor core voltage |
| |
| 12345 Core Voltage |
| ----- |
| SW1=01111 1.000V. |
| SW1=01101 1.100V. |
| SW1=01011 1.200V. |
| SW1=01001 1.300V only for MPC7447A. |
| |
| |
| SW2[1-6]: CPU core frequency |
| |
| CPU Core Frequency (MHz) |
| Bus Frequency |
| 123456 100 133 167 200 Ratio |
| |
| ------ |
| SW2=101100 500 667 833 1000 5x |
| SW2=100100 550 733 917 1100 5.5x |
| SW2=110100 600 800 1000 1200 6x |
| SW2=010100 650 866 1083 1300 6.5x |
| SW2=001000 700 930 1167 1400 7x |
| SW2=000100 750 1000 1250 1500 7.5x |
| SW2=110000 800 1066 1333 1600 8x |
| SW2=011000 850 1333 1417 1700 8.5x only for MPC7447A |
| SW2=011110 900 1200 1500 1800 9x |
| |
| This table shows only a subset of available frequency options; see the CPU |
| hardware specifications for more information. |
| |
| SW2[7-8]: Bus Protocol and CPU Reset Option |
| |
| 7 |
| - |
| SW2=0 System bus uses MPX bus protocol |
| SW2=1 System bus uses 60x bus protocol |
| |
| 8 |
| - |
| SW2=0 TSI108 can cause CPU reset |
| SW2=1 TSI108 can not cause CPU reset |
| |
| SW3[1-8] system options |
| |
| 123 |
| --- |
| SW3=xxx Connected to GPIO[0:2] on TSI108 |
| |
| 4 |
| - |
| SW3=0 CPU boots from low half of flash |
| SW3=1 CPU boots from high half of flash |
| |
| 5 |
| - |
| SW3=0 SATA and slot2 connected to PCI bus |
| SW3=1 Only slot1 connected to PCI bus |
| |
| 6 |
| - |
| SW3=0 USB connected to PCI bus |
| SW3=1 USB disconnected from PCI bus |
| |
| 7 |
| - |
| SW3=0 Flash is write protected |
| SW3=1 Flash is NOT write protected |
| |
| 8 |
| - |
| SW3=0 CPU will boot from flash |
| SW3=1 CPU will boot from PromJet |
| |
| SW4[1-3]: System bus frequency |
| |
| Bus Frequency (MHz) |
| --- |
| SW4=010 183 |
| SW4=011 100 |
| SW4=100 133 |
| SW4=101 166 only for MPC7447A |
| SW4=110 200 only for MPC7448 |
| others reserved |
| |
| SW4[4-6]: DDR2 SDRAM frequency |
| |
| Bus Frequency (MHz) |
| --- |
| SW4=000 external clock |
| SW4=011 system clock |
| SW4=100 133 |
| SW4=101 166 |
| SW4=110 200 |
| others reserved |
| |
| SW4[7-8]: PCI/PCI-X frequency control |
| 7 |
| - |
| SW4=0 PCI/PCI-X bus operates normally |
| SW4=1 PCI bus forced to PCI-33 mode |
| |
| 8 |
| - |
| SW4=0 PCI-X mode at 133 MHz allowed |
| SW4=1 PCI-X mode limited to 100 MHz |