| /* |
| * Pinmux configuration for Compulab CM-T54 board |
| * |
| * Copyright (C) 2014, Compulab Ltd - http://compulab.co.il/ |
| * |
| * Author: Dmitry Lifshitz <lifshitz@compulab.co.il> |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| #ifndef _CM_T54_MUX_DATA_H |
| #define _CM_T54_MUX_DATA_H |
| |
| #include <asm/arch/mux_omap5.h> |
| #include <asm/arch/sys_proto.h> |
| |
| const struct pad_conf_entry core_padconf_array_essential[] = { |
| /* MMC1 - SD CARD */ |
| {SDCARD_CLK, (PTU | IEN | M0)}, /* SDCARD_CLK */ |
| {SDCARD_CMD, (PTU | IEN | M0)}, /* SDCARD_CMD */ |
| {SDCARD_DATA0, (PTU | IEN | M0)}, /* SDCARD_DATA0 */ |
| {SDCARD_DATA1, (PTU | IEN | M0)}, /* SDCARD_DATA1 */ |
| {SDCARD_DATA2, (PTU | IEN | M0)}, /* SDCARD_DATA2 */ |
| {SDCARD_DATA3, (PTU | IEN | M0)}, /* SDCARD_DATA3 */ |
| |
| /* SD CARD CD and WP GPIOs*/ |
| {TIMER5_PWM_EVT, (PTU | IEN | M6)}, /* GPIO8_228 */ |
| {TIMER6_PWM_EVT, (PTU | IEN | M6)}, /* GPIO8_229 */ |
| |
| /* MMC2 - eMMC */ |
| {EMMC_CLK, (PTU | IEN | M0)}, /* EMMC_CLK */ |
| {EMMC_CMD, (PTU | IEN | M0)}, /* EMMC_CMD */ |
| {EMMC_DATA0, (PTU | IEN | M0)}, /* EMMC_DATA0 */ |
| {EMMC_DATA1, (PTU | IEN | M0)}, /* EMMC_DATA1 */ |
| {EMMC_DATA2, (PTU | IEN | M0)}, /* EMMC_DATA2 */ |
| {EMMC_DATA3, (PTU | IEN | M0)}, /* EMMC_DATA3 */ |
| {EMMC_DATA4, (PTU | IEN | M0)}, /* EMMC_DATA4 */ |
| {EMMC_DATA5, (PTU | IEN | M0)}, /* EMMC_DATA5 */ |
| {EMMC_DATA6, (PTU | IEN | M0)}, /* EMMC_DATA6 */ |
| {EMMC_DATA7, (PTU | IEN | M0)}, /* EMMC_DATA7 */ |
| |
| /* UART4 */ |
| {I2C5_SCL, (PTU | IEN | M2)}, /* UART4_RX */ |
| {I2C5_SDA, (M2)}, /* UART4_TX */ |
| |
| /* Led */ |
| {HSI2_CAFLAG, (PTU | M6)}, /* GPIO3_80 */ |
| |
| /* I2C1 */ |
| {I2C1_PMIC_SCL, (PTU | IEN | M0)}, /* I2C1_PMIC_SCL */ |
| {I2C1_PMIC_SDA, (PTU | IEN | M0)}, /* I2C1_PMIC_SDA */ |
| |
| /* USBB2, USBB3 */ |
| {USBB2_HSIC_STROBE, (PTU | IEN | M0)}, /* USBB2_HSIC_STROBE */ |
| {USBB2_HSIC_DATA, (PTU | IEN | M0)}, /* USBB2_HSIC_DATA */ |
| {USBB3_HSIC_STROBE, (PTU | IEN | M0)}, /* USBB3_HSIC_STROBE */ |
| {USBB3_HSIC_DATA, (PTU | IEN | M0)}, /* USBB3_HSIC_DATA */ |
| |
| /* USB Hub and USB Eth reset GPIOs */ |
| {HSI2_CAREADY, (PTD | M6)}, /* GPIO3_76 */ |
| {HSI2_ACDATA, (PTD | M6)}, /* GPIO3_83 */ |
| |
| /* I2C4 */ |
| {I2C4_SCL, (PTU | IEN | M0)}, /* I2C4_SCL */ |
| {I2C4_SDA, (PTU | IEN | M0)}, /* I2C4_SDA */ |
| }; |
| |
| const struct pad_conf_entry wkup_padconf_array_essential[] = { |
| {SR_PMIC_SCL, (PTU | IEN | M0)}, /* SR_PMIC_SCL */ |
| {SR_PMIC_SDA, (PTU | IEN | M0)}, /* SR_PMIC_SDA */ |
| {SYS_32K, (IEN | M0)}, /* SYS_32K */ |
| |
| /* USB Hub clock */ |
| {FREF_CLK1_OUT, (PTD | IEN | M0)}, /* FREF_CLK1_OUT */ |
| }; |
| |
| /* |
| * Routine: set_muxconf_regs |
| * Description: setup board pinmux configuration. |
| */ |
| void set_muxconf_regs(void) |
| { |
| do_set_mux((*ctrl)->control_padconf_core_base, |
| core_padconf_array_essential, |
| sizeof(core_padconf_array_essential) / |
| sizeof(struct pad_conf_entry)); |
| |
| do_set_mux((*ctrl)->control_padconf_wkup_base, |
| wkup_padconf_array_essential, |
| sizeof(wkup_padconf_array_essential) / |
| sizeof(struct pad_conf_entry)); |
| } |
| |
| #endif /* _CM_T54_MUX_DATA_H */ |