arch/x86/cpu/qemu/pci.c

/*
 * Copyright (C) 2015, Bin Meng <bmeng.cn@gmail.com>
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#include <common.h>
#include <pci.h>
#include <pci_rom.h>
#include <asm/pci.h>
#include <asm/arch/device.h>
#include <asm/arch/qemu.h>

DECLARE_GLOBAL_DATA_PTR;

static bool i440fx;

void board_pci_setup_hose(struct pci_controller *hose)
{
	hose->first_busno = 0;
	hose->last_busno = 0;

	/* PCI memory space */
	pci_set_region(hose->regions + 0,
		       CONFIG_PCI_MEM_BUS,
		       CONFIG_PCI_MEM_PHYS,
		       CONFIG_PCI_MEM_SIZE,
		       PCI_REGION_MEM);

	/* PCI IO space */
	pci_set_region(hose->regions + 1,
		       CONFIG_PCI_IO_BUS,
		       CONFIG_PCI_IO_PHYS,
		       CONFIG_PCI_IO_SIZE,
		       PCI_REGION_IO);

	pci_set_region(hose->regions + 2,
		       CONFIG_PCI_PREF_BUS,
		       CONFIG_PCI_PREF_PHYS,
		       CONFIG_PCI_PREF_SIZE,
		       PCI_REGION_PREFETCH);

	pci_set_region(hose->regions + 3,
		       0,
		       0,
		       gd->ram_size,
		       PCI_REGION_MEM | PCI_REGION_SYS_MEMORY);

	hose->region_count = 4;
}

int board_pci_post_scan(struct pci_controller *hose)
{
	int ret = 0;
	u16 device, xbcs;
	int pam, i;
	pci_dev_t vga;
	ulong start;

	/*
	 * i440FX and Q35 chipset have different PAM register offset, but with
	 * the same bitfield layout. Here we determine the offset based on its
	 * PCI device ID.
	 */
	device = x86_pci_read_config16(PCI_BDF(0, 0, 0), PCI_DEVICE_ID);
	i440fx = (device == PCI_DEVICE_ID_INTEL_82441);
	pam = i440fx ? I440FX_PAM : Q35_PAM;

	/*
	 * Initialize Programmable Attribute Map (PAM) Registers
	 *
	 * Configure legacy segments C/D/E/F to system RAM
	 */
	for (i = 0; i < PAM_NUM; i++)
		x86_pci_write_config8(PCI_BDF(0, 0, 0), pam + i, PAM_RW);

	if (i440fx) {
		/*
		 * Enable legacy IDE I/O ports decode
		 *
		 * Note: QEMU always decode legacy IDE I/O port on PIIX chipset.
		 * However Linux ata_piix driver does sanity check on these two
		 * registers to see whether legacy ports decode is turned on.
		 * This is to make Linux ata_piix driver happy.
		 */
		x86_pci_write_config16(PIIX_IDE, IDE0_TIM, IDE_DECODE_EN);
		x86_pci_write_config16(PIIX_IDE, IDE1_TIM, IDE_DECODE_EN);

		/* Enable I/O APIC */
		xbcs = x86_pci_read_config16(PIIX_ISA, XBCS);
		xbcs |= APIC_EN;
		x86_pci_write_config16(PIIX_ISA, XBCS, xbcs);
	} else {
		/* Configure PCIe ECAM base address */
		x86_pci_write_config32(PCI_BDF(0, 0, 0), PCIEX_BAR,
				       CONFIG_PCIE_ECAM_BASE | BAR_EN);
	}

	/*
	 * QEMU emulated graphic card shows in the PCI configuration space with
	 * PCI vendor id and device id as an artificial pair 0x1234:0x1111.
	 * It is on PCI bus 0, function 0, but device number is not consistent
	 * for the two x86 targets it supports. For i440FX and PIIX chipset
	 * board, it shows as device 2, while for Q35 and ICH9 chipset board,
	 * it shows as device 1.
	 */
	vga = i440fx ? I440FX_VGA : Q35_VGA;
	start = get_timer(0);
	ret = pci_run_vga_bios(vga, NULL, PCI_ROM_USE_NATIVE);
	debug("BIOS ran in %lums\n", get_timer(start));

	return ret;
}

#ifdef CONFIG_GENERATE_MP_TABLE
int mp_determine_pci_dstirq(int bus, int dev, int func, int pirq)
{
	u8 irq;

	if (i440fx) {
		/*
		 * Not like most x86 platforms, the PIRQ[A-D] on PIIX3 are not
		 * connected to I/O APIC INTPIN#16-19. Instead they are routed
		 * to an irq number controled by the PIRQ routing register.
		 */
		irq = x86_pci_read_config8(PCI_BDF(bus, dev, func),
					   PCI_INTERRUPT_LINE);
	} else {
		/*
		 * ICH9's PIRQ[A-H] are not consecutive numbers from 0 to 7.
		 * PIRQ[A-D] still maps to [0-3] but PIRQ[E-H] maps to [8-11].
		 */
		irq = pirq < 8 ? pirq + 16 : pirq + 12;
	}

	return irq;
}
#endif