| /* |
| * Copyright (C) 2015, Bin Meng <bmeng.cn@gmail.com> |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| #include <common.h> |
| #include <mmc.h> |
| #include <netdev.h> |
| #include <phy.h> |
| #include <asm/io.h> |
| #include <asm/pci.h> |
| #include <asm/post.h> |
| #include <asm/processor.h> |
| #include <asm/arch/device.h> |
| #include <asm/arch/msg_port.h> |
| #include <asm/arch/quark.h> |
| |
| static struct pci_device_id mmc_supported[] = { |
| { PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_QRK_SDIO }, |
| }; |
| |
| /* |
| * TODO: |
| * |
| * This whole routine should be removed until we fully convert the ICH SPI |
| * driver to DM and make use of DT to pass the bios control register offset |
| */ |
| static void unprotect_spi_flash(void) |
| { |
| u32 bc; |
| |
| bc = pci_read_config32(QUARK_LEGACY_BRIDGE, 0xd8); |
| bc |= 0x1; /* unprotect the flash */ |
| pci_write_config32(QUARK_LEGACY_BRIDGE, 0xd8, bc); |
| } |
| |
| static void quark_setup_bars(void) |
| { |
| /* GPIO - D31:F0:R44h */ |
| pci_write_config_dword(QUARK_LEGACY_BRIDGE, LB_GBA, |
| CONFIG_GPIO_BASE | IO_BAR_EN); |
| |
| /* ACPI PM1 Block - D31:F0:R48h */ |
| pci_write_config_dword(QUARK_LEGACY_BRIDGE, LB_PM1BLK, |
| CONFIG_ACPI_PM1_BASE | IO_BAR_EN); |
| |
| /* GPE0 - D31:F0:R4Ch */ |
| pci_write_config_dword(QUARK_LEGACY_BRIDGE, LB_GPE0BLK, |
| CONFIG_ACPI_GPE0_BASE | IO_BAR_EN); |
| |
| /* WDT - D31:F0:R84h */ |
| pci_write_config_dword(QUARK_LEGACY_BRIDGE, LB_WDTBA, |
| CONFIG_WDT_BASE | IO_BAR_EN); |
| |
| /* RCBA - D31:F0:RF0h */ |
| pci_write_config_dword(QUARK_LEGACY_BRIDGE, LB_RCBA, |
| CONFIG_RCBA_BASE | MEM_BAR_EN); |
| |
| /* ACPI P Block - Msg Port 04:R70h */ |
| msg_port_write(MSG_PORT_RMU, PBLK_BA, |
| CONFIG_ACPI_PBLK_BASE | IO_BAR_EN); |
| |
| /* SPI DMA - Msg Port 04:R7Ah */ |
| msg_port_write(MSG_PORT_RMU, SPI_DMA_BA, |
| CONFIG_SPI_DMA_BASE | IO_BAR_EN); |
| |
| /* PCIe ECAM */ |
| msg_port_write(MSG_PORT_MEM_ARBITER, AEC_CTRL, |
| CONFIG_PCIE_ECAM_BASE | MEM_BAR_EN); |
| msg_port_write(MSG_PORT_HOST_BRIDGE, HEC_REG, |
| CONFIG_PCIE_ECAM_BASE | MEM_BAR_EN); |
| } |
| |
| int arch_cpu_init(void) |
| { |
| struct pci_controller *hose; |
| int ret; |
| |
| post_code(POST_CPU_INIT); |
| #ifdef CONFIG_SYS_X86_TSC_TIMER |
| timer_set_base(rdtsc()); |
| #endif |
| |
| ret = x86_cpu_init_f(); |
| if (ret) |
| return ret; |
| |
| ret = pci_early_init_hose(&hose); |
| if (ret) |
| return ret; |
| |
| /* |
| * Quark SoC has some non-standard BARs (excluding PCI standard BARs) |
| * which need be initialized with suggested values |
| */ |
| quark_setup_bars(); |
| |
| unprotect_spi_flash(); |
| |
| return 0; |
| } |
| |
| int print_cpuinfo(void) |
| { |
| post_code(POST_CPU_INFO); |
| return default_print_cpuinfo(); |
| } |
| |
| void reset_cpu(ulong addr) |
| { |
| /* cold reset */ |
| outb(0x08, PORT_RESET); |
| } |
| |
| int cpu_mmc_init(bd_t *bis) |
| { |
| return pci_mmc_init("Quark SDHCI", mmc_supported, |
| ARRAY_SIZE(mmc_supported)); |
| } |
| |
| int cpu_eth_init(bd_t *bis) |
| { |
| u32 base; |
| int ret0, ret1; |
| |
| pci_read_config_dword(QUARK_EMAC0, PCI_BASE_ADDRESS_0, &base); |
| ret0 = designware_initialize(base, PHY_INTERFACE_MODE_RMII); |
| |
| pci_read_config_dword(QUARK_EMAC1, PCI_BASE_ADDRESS_0, &base); |
| ret1 = designware_initialize(base, PHY_INTERFACE_MODE_RMII); |
| |
| if (ret0 < 0 && ret1 < 0) |
| return -1; |
| else |
| return 0; |
| } |