blob: c9cbf8f5e37247367203953f13e3ceca5039638b [file] [log] [blame]
/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright (C) 2012 Altera Corporation <www.altera.com>
*/
#ifndef __CONFIG_SOCFPGA_COMMON_H__
#define __CONFIG_SOCFPGA_COMMON_H__
/*
* High level configuration
*/
#define CONFIG_CLOCKS
#define CONFIG_SYS_BOOTMAPSZ (64 * 1024 * 1024)
#define CONFIG_TIMESTAMP /* Print image info with timestamp */
/*
* Memory configurations
*/
#define PHYS_SDRAM_1 0x0
#define CONFIG_SYS_MALLOC_LEN (64 * 1024 * 1024)
#define CONFIG_SYS_MEMTEST_START PHYS_SDRAM_1
#define CONFIG_SYS_MEMTEST_END PHYS_SDRAM_1_SIZE
#if defined(CONFIG_TARGET_SOCFPGA_GEN5)
#define CONFIG_SYS_INIT_RAM_ADDR 0xFFFF0000
#define CONFIG_SYS_INIT_RAM_SIZE 0x10000
#elif defined(CONFIG_TARGET_SOCFPGA_ARRIA10)
#define CONFIG_SYS_INIT_RAM_ADDR 0xFFE00000
#define CONFIG_SYS_INIT_RAM_SIZE 0x40000 /* 256KB */
#endif
/*
* Some boards (e.g. socfpga_sr1500) use 8 bytes at the end of the internal
* SRAM as bootcounter storage. Make sure to not put the stack directly
* at this address to not overwrite the bootcounter by checking, if the
* bootcounter address is located in the internal SRAM.
*/
#if ((CONFIG_SYS_BOOTCOUNT_ADDR > CONFIG_SYS_INIT_RAM_ADDR) && \
(CONFIG_SYS_BOOTCOUNT_ADDR < (CONFIG_SYS_INIT_RAM_ADDR + \
CONFIG_SYS_INIT_RAM_SIZE)))
#define CONFIG_SYS_INIT_SP_ADDR CONFIG_SYS_BOOTCOUNT_ADDR
#else
#define CONFIG_SYS_INIT_SP_ADDR \
(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_RAM_SIZE)
#endif
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
/*
* U-Boot general configurations
*/
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O buffer size */
/* Print buffer size */
#define CONFIG_SYS_MAXARGS 32 /* Max number of command args */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
/* Boot argument buffer size */
#ifndef CONFIG_SYS_HOSTNAME
#define CONFIG_SYS_HOSTNAME CONFIG_SYS_BOARD
#endif
/*
* Cache
*/
#define CONFIG_SYS_L2_PL310
#define CONFIG_SYS_PL310_BASE SOCFPGA_MPUL2_ADDRESS
/*
* EPCS/EPCQx1 Serial Flash Controller
*/
#ifdef CONFIG_ALTERA_SPI
#define CONFIG_SF_DEFAULT_SPEED 30000000
/*
* The base address is configurable in QSys, each board must specify the
* base address based on it's particular FPGA configuration. Please note
* that the address here is incremented by 0x400 from the Base address
* selected in QSys, since the SPI registers are at offset +0x400.
* #define CONFIG_SYS_SPI_BASE 0xff240400
*/
#endif
/*
* Ethernet on SoC (EMAC)
*/
#ifdef CONFIG_CMD_NET
#define CONFIG_DW_ALTDESCRIPTOR
#endif
/*
* FPGA Driver
*/
#ifdef CONFIG_CMD_FPGA
#define CONFIG_FPGA_COUNT 1
#endif
/*
* L4 OSC1 Timer 0
*/
#ifndef CONFIG_TIMER
/* This timer uses eosc1, whose clock frequency is fixed at any condition. */
#define CONFIG_SYS_TIMERBASE SOCFPGA_OSC1TIMER0_ADDRESS
#define CONFIG_SYS_TIMER_COUNTS_DOWN
#define CONFIG_SYS_TIMER_COUNTER (CONFIG_SYS_TIMERBASE + 0x4)
#define CONFIG_SYS_TIMER_RATE 25000000
#endif
/*
* L4 Watchdog
*/
#ifdef CONFIG_HW_WATCHDOG
#define CONFIG_DESIGNWARE_WATCHDOG
#define CONFIG_DW_WDT_BASE SOCFPGA_L4WD0_ADDRESS
#define CONFIG_DW_WDT_CLOCK_KHZ 25000
#define CONFIG_WATCHDOG_TIMEOUT_MSECS 30000
#endif
/*
* MMC Driver
*/
#ifdef CONFIG_CMD_MMC
/* FIXME */
/* using smaller max blk cnt to avoid flooding the limited stack we have */
#define CONFIG_SYS_MMC_MAX_BLK_COUNT 256 /* FIXME -- SPL only? */
#endif
/*
* NAND Support
*/
#ifdef CONFIG_NAND_DENALI
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_SYS_NAND_ONFI_DETECTION
#define CONFIG_SYS_NAND_REGS_BASE SOCFPGA_NANDREGS_ADDRESS
#define CONFIG_SYS_NAND_DATA_BASE SOCFPGA_NANDDATA_ADDRESS
#endif
/*
* I2C support
*/
#ifndef CONFIG_DM_I2C
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_BASE SOCFPGA_I2C0_ADDRESS
#define CONFIG_SYS_I2C_BASE1 SOCFPGA_I2C1_ADDRESS
#define CONFIG_SYS_I2C_BASE2 SOCFPGA_I2C2_ADDRESS
#define CONFIG_SYS_I2C_BASE3 SOCFPGA_I2C3_ADDRESS
/* Using standard mode which the speed up to 100Kb/s */
#define CONFIG_SYS_I2C_SPEED 100000
#define CONFIG_SYS_I2C_SPEED1 100000
#define CONFIG_SYS_I2C_SPEED2 100000
#define CONFIG_SYS_I2C_SPEED3 100000
/* Address of device when used as slave */
#define CONFIG_SYS_I2C_SLAVE 0x02
#define CONFIG_SYS_I2C_SLAVE1 0x02
#define CONFIG_SYS_I2C_SLAVE2 0x02
#define CONFIG_SYS_I2C_SLAVE3 0x02
#ifndef __ASSEMBLY__
/* Clock supplied to I2C controller in unit of MHz */
unsigned int cm_get_l4_sp_clk_hz(void);
#define IC_CLK (cm_get_l4_sp_clk_hz() / 1000000)
#endif
#endif /* CONFIG_DM_I2C */
/*
* QSPI support
*/
/* Enable multiple SPI NOR flash manufacturers */
#ifndef CONFIG_SPL_BUILD
#define CONFIG_SPI_FLASH_MTD
#endif
/* QSPI reference clock */
#ifndef __ASSEMBLY__
unsigned int cm_get_qspi_controller_clk_hz(void);
#define CONFIG_CQSPI_REF_CLK cm_get_qspi_controller_clk_hz()
#endif
/*
* Designware SPI support
*/
/*
* Serial Driver
*/
#define CONFIG_SYS_NS16550_SERIAL
/*
* USB
*/
/*
* USB Gadget (DFU, UMS)
*/
#if defined(CONFIG_CMD_DFU) || defined(CONFIG_CMD_USB_MASS_STORAGE)
#define CONFIG_SYS_DFU_DATA_BUF_SIZE (16 * 1024 * 1024)
#define DFU_DEFAULT_POLL_TIMEOUT 300
/* USB IDs */
#define CONFIG_G_DNL_UMS_VENDOR_NUM 0x0525
#define CONFIG_G_DNL_UMS_PRODUCT_NUM 0xA4A5
#endif
/*
* U-Boot environment
*/
#if !defined(CONFIG_ENV_SIZE)
#define CONFIG_ENV_SIZE (8 * 1024)
#endif
/* Environment for SDMMC boot */
#if defined(CONFIG_ENV_IS_IN_MMC) && !defined(CONFIG_ENV_OFFSET)
#define CONFIG_SYS_MMC_ENV_DEV 0 /* device 0 */
#define CONFIG_ENV_OFFSET (34 * 512) /* just after the GPT */
#endif
/* Environment for QSPI boot */
#if defined(CONFIG_ENV_IS_IN_SPI_FLASH) && !defined(CONFIG_ENV_OFFSET)
#define CONFIG_ENV_OFFSET 0x00100000
#define CONFIG_ENV_SECT_SIZE (64 * 1024)
#endif
/*
* mtd partitioning for serial NOR flash
*
* device nor0 <ff705000.spi.0>, # parts = 6
* #: name size offset mask_flags
* 0: u-boot 0x00100000 0x00000000 0
* 1: env1 0x00040000 0x00100000 0
* 2: env2 0x00040000 0x00140000 0
* 3: UBI 0x03e80000 0x00180000 0
* 4: boot 0x00e80000 0x00180000 0
* 5: rootfs 0x01000000 0x01000000 0
*
*/
/*
* SPL
*
* SRAM Memory layout for gen 5:
*
* 0xFFFF_0000 ...... Start of SRAM
* 0xFFFF_xxxx ...... Top of stack (grows down)
* 0xFFFF_yyyy ...... Malloc area
* 0xFFFF_zzzz ...... Global Data
* 0xFFFF_FF00 ...... End of SRAM
*
* SRAM Memory layout for Arria 10:
* 0xFFE0_0000 ...... Start of SRAM (bottom)
* 0xFFEx_xxxx ...... Top of stack (grows down to bottom)
* 0xFFEy_yyyy ...... Global Data
* 0xFFEz_zzzz ...... Malloc area (grows up to top)
* 0xFFE3_FFFF ...... End of SRAM (top)
*/
#define CONFIG_SPL_TEXT_BASE CONFIG_SYS_INIT_RAM_ADDR
#define CONFIG_SPL_MAX_SIZE CONFIG_SYS_INIT_RAM_SIZE
#if defined(CONFIG_TARGET_SOCFPGA_ARRIA10)
/* SPL memory allocation configuration, this is for FAT implementation */
#ifndef CONFIG_SYS_SPL_MALLOC_START
#define CONFIG_SYS_SPL_MALLOC_SIZE 0x00010000
#define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SYS_INIT_RAM_SIZE - \
CONFIG_SYS_SPL_MALLOC_SIZE + \
CONFIG_SYS_INIT_RAM_ADDR)
#endif
#endif
/* SPL SDMMC boot support */
#ifdef CONFIG_SPL_MMC_SUPPORT
#if defined(CONFIG_SPL_FS_FAT) || defined(CONFIG_SPL_FS_EXT4)
#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot-dtb.img"
#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
#endif
#else
#ifndef CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION
#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION 1
#endif
#endif
/* SPL QSPI boot support */
#ifdef CONFIG_SPL_SPI_SUPPORT
#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x40000
#endif
/* SPL NAND boot support */
#ifdef CONFIG_SPL_NAND_SUPPORT
#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0
#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x40000
#endif
/*
* Stack setup
*/
#if defined(CONFIG_TARGET_SOCFPGA_GEN5)
#define CONFIG_SPL_STACK CONFIG_SYS_INIT_SP_ADDR
#elif defined(CONFIG_TARGET_SOCFPGA_ARRIA10)
#define CONFIG_SPL_STACK CONFIG_SYS_SPL_MALLOC_START
#endif
/* Extra Environment */
#ifndef CONFIG_SPL_BUILD
#ifdef CONFIG_CMD_DHCP
#define BOOT_TARGET_DEVICES_DHCP(func) func(DHCP, dhcp, na)
#else
#define BOOT_TARGET_DEVICES_DHCP(func)
#endif
#if defined(CONFIG_CMD_PXE) && defined(CONFIG_CMD_DHCP)
#define BOOT_TARGET_DEVICES_PXE(func) func(PXE, pxe, na)
#else
#define BOOT_TARGET_DEVICES_PXE(func)
#endif
#ifdef CONFIG_CMD_MMC
#define BOOT_TARGET_DEVICES_MMC(func) func(MMC, mmc, 0)
#else
#define BOOT_TARGET_DEVICES_MMC(func)
#endif
#define BOOT_TARGET_DEVICES(func) \
BOOT_TARGET_DEVICES_MMC(func) \
BOOT_TARGET_DEVICES_PXE(func) \
BOOT_TARGET_DEVICES_DHCP(func)
#include <config_distro_bootcmd.h>
#ifndef CONFIG_EXTRA_ENV_SETTINGS
#define CONFIG_EXTRA_ENV_SETTINGS \
"fdtfile=" CONFIG_DEFAULT_FDT_FILE "\0" \
"bootm_size=0xa000000\0" \
"kernel_addr_r="__stringify(CONFIG_SYS_LOAD_ADDR)"\0" \
"fdt_addr_r=0x02000000\0" \
"scriptaddr=0x02100000\0" \
"pxefile_addr_r=0x02200000\0" \
"ramdisk_addr_r=0x02300000\0" \
BOOTENV
#endif
#endif
#endif /* __CONFIG_SOCFPGA_COMMON_H__ */