include/configs/omap3_evm_common.h - github/trini/u-boot - Gitiles

 /*
  * Common configuration settings for the TI OMAP3 EVM board.
  *
  * Copyright (C) 2006-2011 Texas Instruments Incorporated - http://www.ti.com/
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */

 #ifndef __OMAP3_EVM_COMMON_H
 #define __OMAP3_EVM_COMMON_H

 /*
  * High level configuration options
  */
 #define CONFIG_OMAP			/* This is TI OMAP core */
 #define CONFIG_OMAP34XX			/* belonging to 34XX family */
 #define CONFIG_OMAP_GPIO

 #define CONFIG_SDRC			/* The chip has SDRC controller */

 #define CONFIG_OMAP3_EVM		/* This is a OMAP3 EVM */
 #define CONFIG_TWL4030_POWER		/* with TWL4030 PMIC */

 /*
  * Clock related definitions
  */
 #define V_OSCK			26000000	/* Clock output from T2 */
 #define V_SCLK			(V_OSCK >> 1)

 /*
  * OMAP3 has 12 GP timers, they can be driven by the system clock
  * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK).
  * This rate is divided by a local divisor.
  */
 #define CONFIG_SYS_TIMERBASE		OMAP34XX_GPT2
 #define CONFIG_SYS_PTV			2	/* Divisor: 2^(PTV+1) => 8 */
 #define CONFIG_SYS_HZ			1000

 /* Size of environment - 128KB */
 #define CONFIG_ENV_SIZE			(128 << 10)

 /* Size of malloc pool */
 #define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + (128 << 10))

 /*
  * Physical Memory Map
  * Note 1: CS1 may or may not be populated
  * Note 2: SDRAM size is expected to be at least 32MB
  */
 #define CONFIG_NR_DRAM_BANKS		2
 #define PHYS_SDRAM_1			OMAP34XX_SDRC_CS0
 #define PHYS_SDRAM_2			OMAP34XX_SDRC_CS1

 /* Limits for memtest */
 #define CONFIG_SYS_MEMTEST_START	(OMAP34XX_SDRC_CS0)
 #define CONFIG_SYS_MEMTEST_END		(OMAP34XX_SDRC_CS0 + \
 						0x01F00000) /* 31MB */

 /* Default load address */
 #define CONFIG_SYS_LOAD_ADDR		(OMAP34XX_SDRC_CS0)

 /* -----------------------------------------------------------------------------
  * Hardware drivers
  * -----------------------------------------------------------------------------
  */

 /*
  * NS16550 Configuration
  */
 #define V_NS16550_CLK			48000000	/* 48MHz (APLL96/2) */

 #define CONFIG_SYS_NS16550
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE	(-4)
 #define CONFIG_SYS_NS16550_CLK		V_NS16550_CLK

 /*
  * select serial console configuration
  */
 #define CONFIG_CONS_INDEX		1
 #define CONFIG_SERIAL1			1	/* UART1 on OMAP3 EVM */
 #define CONFIG_SYS_NS16550_COM1		OMAP34XX_UART1
 #define CONFIG_BAUDRATE			115200
 #define CONFIG_SYS_BAUDRATE_TABLE	{4800, 9600, 19200, 38400, 57600,\
 					115200}

 /*
  * I2C
  */
 #define CONFIG_HARD_I2C
 #define CONFIG_DRIVER_OMAP34XX_I2C

 #define CONFIG_SYS_I2C_SPEED		100000
 #define CONFIG_SYS_I2C_SLAVE		1

 /*
  * PISMO support
  */
 #define PISMO1_NAND_SIZE		GPMC_SIZE_128M
 #define PISMO1_ONEN_SIZE		GPMC_SIZE_128M

 /* Monitor at start of flash - Reserve 2 sectors */
 #define CONFIG_SYS_MONITOR_BASE		CONFIG_SYS_FLASH_BASE

 #define CONFIG_SYS_MONITOR_LEN		(256 << 10)

 /* Start location & size of environment */
 #define ONENAND_ENV_OFFSET		0x260000
 #define SMNAND_ENV_OFFSET		0x260000

 #define CONFIG_SYS_ENV_SECT_SIZE	(128 << 10)	/* 128 KiB */

 /*
  * NAND
  */
 /* Physical address to access NAND */
 #define CONFIG_SYS_NAND_ADDR		NAND_BASE

 /* Physical address to access NAND at CS0 */
 #define CONFIG_SYS_NAND_BASE		NAND_BASE

 /* Max number of NAND devices */
 #define CONFIG_SYS_MAX_NAND_DEVICE	1

 /* Timeout values (in ticks) */
 #define CONFIG_SYS_FLASH_ERASE_TOUT	(100 * CONFIG_SYS_HZ)
 #define CONFIG_SYS_FLASH_WRITE_TOUT	(100 * CONFIG_SYS_HZ)

 /* Flash banks JFFS2 should use */
 #define CONFIG_SYS_MAX_MTD_BANKS	(CONFIG_SYS_MAX_FLASH_BANKS + \
 						CONFIG_SYS_MAX_NAND_DEVICE)

 #define CONFIG_SYS_JFFS2_MEM_NAND
 #define CONFIG_SYS_JFFS2_FIRST_BANK	CONFIG_SYS_MAX_FLASH_BANKS
 #define CONFIG_SYS_JFFS2_NUM_BANKS	1

 #define CONFIG_JFFS2_NAND
 /* nand device jffs2 lives on */
 #define CONFIG_JFFS2_DEV		"nand0"
 /* Start of jffs2 partition */
 #define CONFIG_JFFS2_PART_OFFSET	0x680000
 /* Size of jffs2 partition */
 #define CONFIG_JFFS2_PART_SIZE		0xf980000

 /*
  * USB
  */
 #ifdef CONFIG_USB_OMAP3

 #ifdef CONFIG_MUSB_HCD
 #define CONFIG_CMD_USB

 #define CONFIG_USB_STORAGE
 #define CONGIG_CMD_STORAGE
 #define CONFIG_CMD_FAT

 #ifdef CONFIG_USB_KEYBOARD
 #define CONFIG_SYS_USB_EVENT_POLL
 #define CONFIG_PREBOOT			"usb start"
 #endif /* CONFIG_USB_KEYBOARD */

 #endif /* CONFIG_MUSB_HCD */

 #ifdef CONFIG_MUSB_UDC
 /* USB device configuration */
 #define CONFIG_USB_DEVICE
 #define CONFIG_USB_TTY
 #define CONFIG_SYS_CONSOLE_IS_IN_ENV

 /* Change these to suit your needs */
 #define CONFIG_USBD_VENDORID		0x0451
 #define CONFIG_USBD_PRODUCTID		0x5678
 #define CONFIG_USBD_MANUFACTURER	"Texas Instruments"
 #define CONFIG_USBD_PRODUCT_NAME	"EVM"
 #endif /* CONFIG_MUSB_UDC */

 #endif /* CONFIG_USB_OMAP3 */

 /* ----------------------------------------------------------------------------
  * U-boot features
  * ----------------------------------------------------------------------------
  */
 #define CONFIG_SYS_PROMPT		"OMAP3_EVM # "
 #define CONFIG_SYS_MAXARGS		16	/* max args for a command */

 #define CONFIG_MISC_INIT_R

 #define CONFIG_CMDLINE_TAG			/* enable passing of ATAGs */
 #define CONFIG_SETUP_MEMORY_TAGS
 #define CONFIG_INITRD_TAG
 #define CONFIG_REVISION_TAG

 /* Size of Console IO buffer */
 #define CONFIG_SYS_CBSIZE		512

 /* Size of print buffer */
 #define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + \
 						sizeof(CONFIG_SYS_PROMPT) + 16)

 /* Size of bootarg buffer */
 #define CONFIG_SYS_BARGSIZE		(CONFIG_SYS_CBSIZE)

 #define CONFIG_BOOTFILE			"uImage"

 /*
  * NAND / OneNAND
  */
 #if defined(CONFIG_CMD_NAND)
 #define CONFIG_SYS_FLASH_BASE		PISMO1_NAND_BASE

 #define CONFIG_NAND_OMAP_GPMC
 #define GPMC_NAND_ECC_LP_x16_LAYOUT
 #define CONFIG_ENV_OFFSET		SMNAND_ENV_OFFSET
 #elif defined(CONFIG_CMD_ONENAND)
 #define CONFIG_SYS_FLASH_BASE		PISMO1_ONEN_BASE
 #define CONFIG_SYS_ONENAND_BASE		ONENAND_MAP
 #endif

 #if !defined(CONFIG_ENV_IS_NOWHERE)
 #if defined(CONFIG_CMD_NAND)
 #define CONFIG_ENV_IS_IN_NAND
 #elif defined(CONFIG_CMD_ONENAND)
 #define CONFIG_ENV_IS_IN_ONENAND
 #define CONFIG_ENV_OFFSET		ONENAND_ENV_OFFSET
 #endif
 #endif /* CONFIG_ENV_IS_NOWHERE */

 #define CONFIG_ENV_ADDR			CONFIG_ENV_OFFSET

 #if defined(CONFIG_CMD_NET)

 /* Ethernet (SMSC9115 from SMSC9118 family) */
 #define CONFIG_SMC911X
 #define CONFIG_SMC911X_32_BIT
 #define CONFIG_SMC911X_BASE		0x2C000000

 /* BOOTP fields */
 #define CONFIG_BOOTP_SUBNETMASK		0x00000001
 #define CONFIG_BOOTP_GATEWAY		0x00000002
 #define CONFIG_BOOTP_HOSTNAME		0x00000004
 #define CONFIG_BOOTP_BOOTPATH		0x00000010

 #endif /* CONFIG_CMD_NET */

 /* Support for relocation */
 #define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_1
 #define CONFIG_SYS_INIT_RAM_ADDR	0x4020f800
 #define CONFIG_SYS_INIT_RAM_SIZE	0x800
 #define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_INIT_RAM_ADDR + \
 					 CONFIG_SYS_INIT_RAM_SIZE - \
 					 GENERATED_GBL_DATA_SIZE)

 /* -----------------------------------------------------------------------------
  * Board specific
  * -----------------------------------------------------------------------------
  */
 #define CONFIG_SYS_NO_FLASH

 /* Uncomment to define the board revision statically */
 /* #define CONFIG_STATIC_BOARD_REV	OMAP3EVM_BOARD_GEN_2 */

 #define CONFIG_SYS_CACHELINE_SIZE	64

 /* Defines for SPL */
 #define CONFIG_SPL
 #define CONFIG_SPL_FRAMEWORK
 #define CONFIG_SPL_TEXT_BASE		0x40200800
 #define CONFIG_SPL_MAX_SIZE		(54 * 1024)	/* 8 KB for stack */
 #define CONFIG_SPL_STACK		LOW_LEVEL_SRAM_STACK

 #define CONFIG_SPL_BSS_START_ADDR	0x80000000
 #define CONFIG_SPL_BSS_MAX_SIZE		0x80000		/* 512 KB */

 #define CONFIG_SPL_BOARD_INIT
 #define CONFIG_SPL_LIBCOMMON_SUPPORT
 #define CONFIG_SPL_LIBDISK_SUPPORT
 #define CONFIG_SPL_I2C_SUPPORT
 #define CONFIG_SPL_LIBGENERIC_SUPPORT
 #define CONFIG_SPL_SERIAL_SUPPORT
 #define CONFIG_SPL_POWER_SUPPORT
 #define CONFIG_SPL_OMAP3_ID_NAND
 #define CONFIG_SPL_LDSCRIPT		"$(CPUDIR)/omap-common/u-boot-spl.lds"

 /*
  * 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM
  * 64 bytes before this address should be set aside for u-boot.img's
  * header. That is 0x800FFFC0--0x80100000 should not be used for any
  * other needs.
  */
 #define CONFIG_SYS_TEXT_BASE		0x80100000
 #define CONFIG_SYS_SPL_MALLOC_START	0x80208000
 #define CONFIG_SYS_SPL_MALLOC_SIZE	0x100000

 #endif /* __OMAP3_EVM_COMMON_H */
	/*
	* Common configuration settings for the TI OMAP3 EVM board.
	*
	* Copyright (C) 2006-2011 Texas Instruments Incorporated - http://www.ti.com/
	*
	* SPDX-License-Identifier: GPL-2.0+
	*/

	#ifndef __OMAP3_EVM_COMMON_H
	#define __OMAP3_EVM_COMMON_H

	/*
	* High level configuration options
	*/
	#define CONFIG_OMAP /* This is TI OMAP core */
	#define CONFIG_OMAP34XX /* belonging to 34XX family */
	#define CONFIG_OMAP_GPIO

	#define CONFIG_SDRC /* The chip has SDRC controller */

	#define CONFIG_OMAP3_EVM /* This is a OMAP3 EVM */
	#define CONFIG_TWL4030_POWER /* with TWL4030 PMIC */

	/*
	* Clock related definitions
	*/
	#define V_OSCK 26000000 /* Clock output from T2 */
	#define V_SCLK (V_OSCK >> 1)

	/*
	* OMAP3 has 12 GP timers, they can be driven by the system clock
	* (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK).
	* This rate is divided by a local divisor.
	*/
	#define CONFIG_SYS_TIMERBASE OMAP34XX_GPT2
	#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */
	#define CONFIG_SYS_HZ 1000

	/* Size of environment - 128KB */
	#define CONFIG_ENV_SIZE (128 << 10)

	/* Size of malloc pool */
	#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128 << 10))

	/*
	* Physical Memory Map
	* Note 1: CS1 may or may not be populated
	* Note 2: SDRAM size is expected to be at least 32MB
	*/
	#define CONFIG_NR_DRAM_BANKS 2
	#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
	#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1

	/* Limits for memtest */
	#define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0)
	#define CONFIG_SYS_MEMTEST_END (OMAP34XX_SDRC_CS0 + \
	0x01F00000) /* 31MB */

	/* Default load address */
	#define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0)

	/* -----------------------------------------------------------------------------
	* Hardware drivers
	* -----------------------------------------------------------------------------
	*/

	/*
	* NS16550 Configuration
	*/
	#define V_NS16550_CLK 48000000 /* 48MHz (APLL96/2) */

	#define CONFIG_SYS_NS16550
	#define CONFIG_SYS_NS16550_SERIAL
	#define CONFIG_SYS_NS16550_REG_SIZE (-4)
	#define CONFIG_SYS_NS16550_CLK V_NS16550_CLK

	/*
	* select serial console configuration
	*/
	#define CONFIG_CONS_INDEX 1
	#define CONFIG_SERIAL1 1 /* UART1 on OMAP3 EVM */
	#define CONFIG_SYS_NS16550_COM1 OMAP34XX_UART1
	#define CONFIG_BAUDRATE 115200
	#define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600,\
	115200}

	/*
	* I2C
	*/
	#define CONFIG_HARD_I2C
	#define CONFIG_DRIVER_OMAP34XX_I2C

	#define CONFIG_SYS_I2C_SPEED 100000
	#define CONFIG_SYS_I2C_SLAVE 1

	/*
	* PISMO support
	*/
	#define PISMO1_NAND_SIZE GPMC_SIZE_128M
	#define PISMO1_ONEN_SIZE GPMC_SIZE_128M

	/* Monitor at start of flash - Reserve 2 sectors */
	#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE

	#define CONFIG_SYS_MONITOR_LEN (256 << 10)

	/* Start location & size of environment */
	#define ONENAND_ENV_OFFSET 0x260000
	#define SMNAND_ENV_OFFSET 0x260000

	#define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */

	/*
	* NAND
	*/
	/* Physical address to access NAND */
	#define CONFIG_SYS_NAND_ADDR NAND_BASE

	/* Physical address to access NAND at CS0 */
	#define CONFIG_SYS_NAND_BASE NAND_BASE

	/* Max number of NAND devices */
	#define CONFIG_SYS_MAX_NAND_DEVICE 1

	/* Timeout values (in ticks) */
	#define CONFIG_SYS_FLASH_ERASE_TOUT (100 * CONFIG_SYS_HZ)
	#define CONFIG_SYS_FLASH_WRITE_TOUT (100 * CONFIG_SYS_HZ)

	/* Flash banks JFFS2 should use */
	#define CONFIG_SYS_MAX_MTD_BANKS (CONFIG_SYS_MAX_FLASH_BANKS + \
	CONFIG_SYS_MAX_NAND_DEVICE)

	#define CONFIG_SYS_JFFS2_MEM_NAND
	#define CONFIG_SYS_JFFS2_FIRST_BANK CONFIG_SYS_MAX_FLASH_BANKS
	#define CONFIG_SYS_JFFS2_NUM_BANKS 1

	#define CONFIG_JFFS2_NAND
	/* nand device jffs2 lives on */
	#define CONFIG_JFFS2_DEV "nand0"
	/* Start of jffs2 partition */
	#define CONFIG_JFFS2_PART_OFFSET 0x680000
	/* Size of jffs2 partition */
	#define CONFIG_JFFS2_PART_SIZE 0xf980000

	/*
	* USB
	*/
	#ifdef CONFIG_USB_OMAP3

	#ifdef CONFIG_MUSB_HCD
	#define CONFIG_CMD_USB

	#define CONFIG_USB_STORAGE
	#define CONGIG_CMD_STORAGE
	#define CONFIG_CMD_FAT

	#ifdef CONFIG_USB_KEYBOARD
	#define CONFIG_SYS_USB_EVENT_POLL
	#define CONFIG_PREBOOT "usb start"
	#endif /* CONFIG_USB_KEYBOARD */

	#endif /* CONFIG_MUSB_HCD */

	#ifdef CONFIG_MUSB_UDC
	/* USB device configuration */
	#define CONFIG_USB_DEVICE
	#define CONFIG_USB_TTY
	#define CONFIG_SYS_CONSOLE_IS_IN_ENV

	/* Change these to suit your needs */
	#define CONFIG_USBD_VENDORID 0x0451
	#define CONFIG_USBD_PRODUCTID 0x5678
	#define CONFIG_USBD_MANUFACTURER "Texas Instruments"
	#define CONFIG_USBD_PRODUCT_NAME "EVM"
	#endif /* CONFIG_MUSB_UDC */

	#endif /* CONFIG_USB_OMAP3 */

	/* ----------------------------------------------------------------------------
	* U-boot features
	* ----------------------------------------------------------------------------
	*/
	#define CONFIG_SYS_PROMPT "OMAP3_EVM # "
	#define CONFIG_SYS_MAXARGS 16 /* max args for a command */

	#define CONFIG_MISC_INIT_R

	#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
	#define CONFIG_SETUP_MEMORY_TAGS
	#define CONFIG_INITRD_TAG
	#define CONFIG_REVISION_TAG

	/* Size of Console IO buffer */
	#define CONFIG_SYS_CBSIZE 512

	/* Size of print buffer */
	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
	sizeof(CONFIG_SYS_PROMPT) + 16)

	/* Size of bootarg buffer */
	#define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE)

	#define CONFIG_BOOTFILE "uImage"

	/*
	* NAND / OneNAND
	*/
	#if defined(CONFIG_CMD_NAND)
	#define CONFIG_SYS_FLASH_BASE PISMO1_NAND_BASE

	#define CONFIG_NAND_OMAP_GPMC
	#define GPMC_NAND_ECC_LP_x16_LAYOUT
	#define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET
	#elif defined(CONFIG_CMD_ONENAND)
	#define CONFIG_SYS_FLASH_BASE PISMO1_ONEN_BASE
	#define CONFIG_SYS_ONENAND_BASE ONENAND_MAP
	#endif

	#if !defined(CONFIG_ENV_IS_NOWHERE)
	#if defined(CONFIG_CMD_NAND)
	#define CONFIG_ENV_IS_IN_NAND
	#elif defined(CONFIG_CMD_ONENAND)
	#define CONFIG_ENV_IS_IN_ONENAND
	#define CONFIG_ENV_OFFSET ONENAND_ENV_OFFSET
	#endif
	#endif /* CONFIG_ENV_IS_NOWHERE */

	#define CONFIG_ENV_ADDR CONFIG_ENV_OFFSET

	#if defined(CONFIG_CMD_NET)

	/* Ethernet (SMSC9115 from SMSC9118 family) */
	#define CONFIG_SMC911X
	#define CONFIG_SMC911X_32_BIT
	#define CONFIG_SMC911X_BASE 0x2C000000

	/* BOOTP fields */
	#define CONFIG_BOOTP_SUBNETMASK 0x00000001
	#define CONFIG_BOOTP_GATEWAY 0x00000002
	#define CONFIG_BOOTP_HOSTNAME 0x00000004
	#define CONFIG_BOOTP_BOOTPATH 0x00000010

	#endif /* CONFIG_CMD_NET */

	/* Support for relocation */
	#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
	#define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800
	#define CONFIG_SYS_INIT_RAM_SIZE 0x800
	#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \
	CONFIG_SYS_INIT_RAM_SIZE - \
	GENERATED_GBL_DATA_SIZE)

	/* -----------------------------------------------------------------------------
	* Board specific
	* -----------------------------------------------------------------------------
	*/
	#define CONFIG_SYS_NO_FLASH

	/* Uncomment to define the board revision statically */
	/* #define CONFIG_STATIC_BOARD_REV OMAP3EVM_BOARD_GEN_2 */

	#define CONFIG_SYS_CACHELINE_SIZE 64

	/* Defines for SPL */
	#define CONFIG_SPL
	#define CONFIG_SPL_FRAMEWORK
	#define CONFIG_SPL_TEXT_BASE 0x40200800
	#define CONFIG_SPL_MAX_SIZE (54 * 1024) /* 8 KB for stack */
	#define CONFIG_SPL_STACK LOW_LEVEL_SRAM_STACK

	#define CONFIG_SPL_BSS_START_ADDR 0x80000000
	#define CONFIG_SPL_BSS_MAX_SIZE 0x80000 /* 512 KB */

	#define CONFIG_SPL_BOARD_INIT
	#define CONFIG_SPL_LIBCOMMON_SUPPORT
	#define CONFIG_SPL_LIBDISK_SUPPORT
	#define CONFIG_SPL_I2C_SUPPORT
	#define CONFIG_SPL_LIBGENERIC_SUPPORT
	#define CONFIG_SPL_SERIAL_SUPPORT
	#define CONFIG_SPL_POWER_SUPPORT
	#define CONFIG_SPL_OMAP3_ID_NAND
	#define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/omap-common/u-boot-spl.lds"

	/*
	* 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM
	* 64 bytes before this address should be set aside for u-boot.img's
	* header. That is 0x800FFFC0--0x80100000 should not be used for any
	* other needs.
	*/
	#define CONFIG_SYS_TEXT_BASE 0x80100000
	#define CONFIG_SYS_SPL_MALLOC_START 0x80208000
	#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000

	#endif /* __OMAP3_EVM_COMMON_H */