include/configs/SIMPC8313.h - github/trini/u-boot - Gitiles

 /*
  * Copyright (C) Sheldon Instruments, Inc. 2008
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */
 /*
  * simpc8313 board configuration file
  */

 #ifndef __CONFIG_H
 #define __CONFIG_H

 /*
  * High Level Configuration Options
  */
 #define CONFIG_NAND_U_BOOT

 #define CONFIG_E300			1
 #define CONFIG_MPC83xx			1
 #define CONFIG_MPC831x			1
 #define CONFIG_MPC8313			1

 #define CONFIG_SYS_NAND_U_BOOT_SIZE	(512 << 10)
 #define CONFIG_SYS_NAND_U_BOOT_DST	0x00100000
 #define CONFIG_SYS_NAND_U_BOOT_START	0x00100100
 #define CONFIG_SYS_NAND_U_BOOT_RELOC	0x00010000
 #define CONFIG_SYS_NAND_U_BOOT_RELOC_SP (CONFIG_SYS_NAND_U_BOOT_RELOC + 0x10000)

 #define CONFIG_SYS_TEXT_BASE	0x00100000 /* CONFIG_SYS_NAND_U_BOOT_DST */
 #define CONFIG_SYS_TEXT_BASE_SPL 0xfff00000

 #ifdef CONFIG_NAND_SPL
 #define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE_SPL /* start of monitor */
 #else
 #define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor */
 #endif

 #define CONFIG_PCI
 #define CONFIG_PCI_INDIRECT_BRIDGE
 #define CONFIG_FSL_ELBC			1

 #define CONFIG_MISC_INIT_R

 /*
  * On-board devices
  *
  * TSEC1 is Marvell PHY 88E1118
  */

 #define CONFIG_SYS_33MHZ

 #define CONFIG_83XX_CLKIN		33333333	/* in Hz */

 #define CONFIG_SYS_CLK_FREQ		CONFIG_83XX_CLKIN

 #define CONFIG_SYS_IMMR			0xE0000000

 #if defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
 #define CONFIG_DEFAULT_IMMR		CONFIG_SYS_IMMR
 #endif

 #define CONFIG_SYS_MEMTEST_START	0x00001000
 #define CONFIG_SYS_MEMTEST_END		0x07f00000

 #define CONFIG_SYS_ACR_PIPE_DEP	3	/* Arbiter pipeline depth (0-3) */
 #define CONFIG_SYS_ACR_RPTCNT	3	/* Arbiter repeat count (0-7) */

 /*
  * Device configurations
  */
 #define CONFIG_TSEC1

 /*
  * DDR Setup
  */
 					/* DDR is system memory*/
 #define CONFIG_SYS_DDR_BASE		0x00000000
 #define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_BASE
 #define CONFIG_SYS_DDR_SDRAM_BASE	CONFIG_SYS_DDR_BASE

 #define CONFIG_VERY_BIG_RAM
 #define CONFIG_MAX_MEM_MAPPED		(512 << 20)

 #define CONFIG_SYS_DDRCDR		(DDRCDR_EN \
 					| DDRCDR_PZ_NOMZ \
 					| DDRCDR_NZ_NOMZ \
 					| DDRCDR_M_ODR)
 					/* 0x73000002 TODO ODR & DRN ? */

 /*
  * FLASH on the Local Bus
  */
 #define CONFIG_SYS_NO_FLASH

 #if !defined(CONFIG_NAND_SPL)
 #define CONFIG_SYS_RAMBOOT
 #endif

 #define CONFIG_SYS_INIT_RAM_LOCK	1
 #define CONFIG_SYS_INIT_RAM_ADDR	0xFD000000 /* Initial RAM address */
 #define CONFIG_SYS_INIT_RAM_SIZE	0x1000 /* Size of used area in RAM*/

 #define CONFIG_SYS_GBL_DATA_OFFSET	\
 			(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET

 /* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */
 #define CONFIG_SYS_MONITOR_LEN	(256 * 1024)	/* Reserve 256 kB for Mon */
 #define CONFIG_SYS_MALLOC_LEN	(512 * 1024)	/* Reserved for malloc */

 /*
  * Local Bus LCRR and LBCR regs
  */
 #define CONFIG_SYS_LCRR_DBYP	LCRR_DBYP
 #define CONFIG_SYS_LCRR_EADC	LCRR_EADC_1
 #define CONFIG_SYS_LCRR_CLKDIV	LCRR_CLKDIV_2
 #define CONFIG_SYS_LBC_LBCR	(0x00040000 /* TODO */ \
 				| (0xFF << LBCR_BMT_SHIFT) \
 				| 0xF)	/* 0x0004ff0f */

 				/* LB refresh timer prescal, 266MHz/32 */
 #define CONFIG_SYS_LBC_MRTPR	0x20000000

 /* drivers/mtd/nand/nand.c */
 #ifdef CONFIG_NAND_SPL
 #define CONFIG_SYS_NAND_BASE		0xFFF00000
 #else
 #define CONFIG_SYS_NAND_BASE		0xE2800000
 #endif
 #define CONFIG_SYS_FPGA_BASE		0xFF000000

 #define CONFIG_CMD_NAND
 #define CONFIG_SYS_MAX_NAND_DEVICE	1
 #define CONFIG_MTD_NAND_VERIFY_WRITE
 #define CONFIG_NAND_FSL_ELBC		1

 #define CONFIG_SYS_NAND_BR_PRELIM	(CONFIG_SYS_NAND_BASE \
 				| BR_DECC_CHK_GEN	/* Use HW ECC */ \
 				| BR_PS_8		/* 8 bit Port */ \
 				| BR_MS_FCM		/* MSEL = FCM */ \
 				| BR_V)			/* valid */

 #ifdef CONFIG_NAND_SP
 #define CONFIG_SYS_NAND_OR_PRELIM	(OR_AM_32KB \
 					| OR_FCM_CSCT \
 					| OR_FCM_CST \
 					| OR_FCM_CHT \
 					| OR_FCM_SCY_1 \
 					| OR_FCM_TRLX \
 					| OR_FCM_EHTR)
 #define CONFIG_SYS_LBLAWAR0_PRELIM	(LBLAWAR_EN | LBLAWAR_32KB)
 #define CONFIG_SYS_NAND_PAGE_SIZE	512	/* NAND chip page size */
 					/* NAND chip block size */
 #define CONFIG_SYS_NAND_BLOCK_SIZE	(16 << 10)
 #define NAND_CACHE_PAGES		32
 #elif defined(CONFIG_NAND_LP)
 #define CONFIG_SYS_NAND_OR_PRELIM	(OR_AM_256KB \
 					| OR_FCM_PGS \
 					| OR_FCM_CSCT \
 					| OR_FCM_CST \
 					| OR_FCM_CHT \
 					| OR_FCM_SCY_1 \
 					| OR_FCM_TRLX \
 					| OR_FCM_EHTR)
 #define CONFIG_SYS_LBLAWAR0_PRELIM	(LBLAWAR_EN | LBLAWAR_256KB)
 #define CONFIG_SYS_NAND_PAGE_SIZE	2048	/* NAND chip page size */
 					/* NAND chip block size */
 #define CONFIG_SYS_NAND_BLOCK_SIZE	(128 << 10)
 #define NAND_CACHE_PAGES		64
 #else
 #error Page size of NAND not defined.
 #endif /* CONFIG_NAND_SP */

 #define CONFIG_SYS_NAND_U_BOOT_OFFS	CONFIG_SYS_NAND_BLOCK_SIZE

 #define CONFIG_SYS_BR0_PRELIM		CONFIG_SYS_NAND_BR_PRELIM
 #define CONFIG_SYS_OR0_PRELIM		CONFIG_SYS_NAND_OR_PRELIM

 #define CONFIG_SYS_LBLAWBAR0_PRELIM	CONFIG_SYS_NAND_BASE

 #define CONFIG_SYS_NAND_LBLAWBAR_PRELIM	CONFIG_SYS_LBLAWBAR0_PRELIM
 #define CONFIG_SYS_NAND_LBLAWAR_PRELIM	CONFIG_SYS_LBLAWAR0_PRELIM

 #define CONFIG_SYS_BR1_PRELIM		(CONFIG_SYS_FPGA_BASE \
 					| BR_PS_16 \
 					| BR_MS_UPMA \
 					| BR_V)
 #define CONFIG_SYS_OR1_PRELIM		(OR_AM_2MB \
 					| OR_UPM_BCTLD)

 #define CONFIG_SYS_LBLAWBAR1_PRELIM	CONFIG_SYS_FPGA_BASE
 #define CONFIG_SYS_LBLAWAR1_PRELIM	(LBLAWAR_EN | LBLAWAR_2MB)

 /*
  * JFFS2 configuration
  */
 #define CONFIG_JFFS2_NAND
 #define CONFIG_JFFS2_DEV	"nand0"

 /* mtdparts command line support */
 #define CONFIG_CMD_MTDPARTS
 #define CONFIG_MTD_DEVICE	/* needed for mtdparts commands */
 #define MTDIDS_DEFAULT		"nand0=nand0"
 #define MTDPARTS_DEFAULT	"mtdparts=nand0:2M(u-boot),6M(kernel),-(jffs2)"

 /* pass open firmware flat tree */
 #define CONFIG_OF_LIBFDT		1
 #define CONFIG_OF_BOARD_SETUP		1
 #define CONFIG_OF_STDOUT_VIA_ALIAS	1

 /*
  * Serial Port
  */
 #define CONFIG_CONS_INDEX		1
 #define CONFIG_SYS_NS16550
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE	1
 #ifdef CONFIG_NAND_SPL
 #define CONFIG_NS16550_MIN_FUNCTIONS
 #endif

 #define CONFIG_SYS_BAUDRATE_TABLE	\
 		{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}

 #define CONFIG_SYS_NS16550_COM1		(CONFIG_SYS_IMMR+0x4500)
 #define CONFIG_SYS_NS16550_COM2		(CONFIG_SYS_IMMR+0x4600)

 /* Use the HUSH parser */
 #define CONFIG_SYS_HUSH_PARSER

 /* I2C */
 #define CONFIG_HARD_I2C		/* I2C with hardware support*/
 #define CONFIG_FSL_I2C
 #define CONFIG_I2C_MULTI_BUS
 #define CONFIG_SYS_I2C_SPEED	400000	/* I2C speed and slave address */
 #define CONFIG_SYS_I2C_SLAVE	0x7F
 #define CONFIG_SYS_I2C_NOPROBES	{ {0, 0x69} } /* Don't probe these addrs */
 #define CONFIG_SYS_I2C_OFFSET	0x3000
 #define CONFIG_SYS_I2C2_OFFSET	0x3100

 /*
  * General PCI
  * Addresses are mapped 1-1.
  */
 #define CONFIG_SYS_PCI1_MEM_BASE	0x80000000
 #define CONFIG_SYS_PCI1_MEM_PHYS	CONFIG_SYS_PCI1_MEM_BASE
 #define CONFIG_SYS_PCI1_MEM_SIZE	0x10000000	/* 256M */
 #define CONFIG_SYS_PCI1_MMIO_BASE	0x90000000
 #define CONFIG_SYS_PCI1_MMIO_PHYS	CONFIG_SYS_PCI1_MMIO_BASE
 #define CONFIG_SYS_PCI1_MMIO_SIZE	0x10000000	/* 256M */
 #define CONFIG_SYS_PCI1_IO_BASE		0x00000000
 #define CONFIG_SYS_PCI1_IO_PHYS		0xE2000000
 #define CONFIG_SYS_PCI1_IO_SIZE		0x00100000	/* 1M */

 #define CONFIG_PCI_PNP			/* do pci plug-and-play */
 #define CONFIG_SYS_PCI_SUBSYS_VENDORID	0x1057	/* Motorola */

 /*
  * TSEC
  */
 #define CONFIG_TSEC_ENET		/* TSEC ethernet support */

 #define CONFIG_GMII			/* MII PHY management */

 #ifdef CONFIG_TSEC1
 #define CONFIG_HAS_ETH0
 #define CONFIG_TSEC1_NAME		"TSEC0"
 #define CONFIG_SYS_TSEC1_OFFSET		0x24000
 #define TSEC1_PHY_ADDR			0x0
 #define TSEC1_FLAGS			TSEC_GIGABIT
 #define TSEC1_PHYIDX			0
 #endif

 #ifdef CONFIG_TSEC2
 #define CONFIG_HAS_ETH1
 #define CONFIG_TSEC2_NAME		"TSEC1"
 #define CONFIG_SYS_TSEC2_OFFSET		0x25000
 #define TSEC2_PHY_ADDR			4
 #define TSEC2_FLAGS			TSEC_GIGABIT
 #define TSEC2_PHYIDX			0
 #endif


 /* Options are: TSEC[0-1] */
 #define CONFIG_ETHPRIME			"TSEC1"

 /*
  * Configure on-board RTC
  */
 #define CONFIG_RTC_DS1337
 #define CONFIG_SYS_I2C_RTC_ADDR		0x68

 /*
  * Environment
  */
 #if defined(CONFIG_NAND_U_BOOT)
 	#define CONFIG_ENV_IS_IN_NAND	1
 	#define CONFIG_ENV_OFFSET	(768 * 1024)
 	#define CONFIG_ENV_SECT_SIZE	CONFIG_SYS_NAND_BLOCK_SIZE
 	#define CONFIG_ENV_SIZE		CONFIG_ENV_SECT_SIZE
 	#define CONFIG_ENV_SIZE_REDUND	CONFIG_ENV_SIZE
 	#define CONFIG_ENV_RANGE	(CONFIG_ENV_SECT_SIZE * 4)
 	#define CONFIG_ENV_OFFSET_REDUND	\
 					(CONFIG_ENV_OFFSET + CONFIG_ENV_RANGE)
 #elif !defined(CONFIG_SYS_RAMBOOT)
 	#define CONFIG_ENV_IS_IN_FLASH	1
 	#define CONFIG_ENV_ADDR		\
 			(CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
 	#define CONFIG_ENV_SECT_SIZE	0x10000	/* 64K(one sector) for env */
 	#define CONFIG_ENV_SIZE		0x2000

 /* Address and size of Redundant Environment Sector */
 #else
 	#define CONFIG_ENV_IS_NOWHERE	1	/* Store ENV in memory only */
 	#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - 0x1000)
 	#define CONFIG_ENV_SIZE		0x2000
 #endif

 #define CONFIG_LOADS_ECHO		1 /* echo on for serial download */
 #define CONFIG_SYS_LOADS_BAUD_CHANGE	1 /* allow baudrate change */

 /*
  * BOOTP options
  */
 #define CONFIG_BOOTP_BOOTFILESIZE
 #define CONFIG_BOOTP_BOOTPATH
 #define CONFIG_BOOTP_GATEWAY
 #define CONFIG_BOOTP_HOSTNAME


 /*
  * Command line configuration.
  */
 #include <config_cmd_default.h>
 #undef CONFIG_CMD_IMLS
 #undef CONFIG_CMD_FLASH

 #define CONFIG_CMD_PING
 #define CONFIG_CMD_DHCP
 #define CONFIG_CMD_I2C
 #define CONFIG_CMD_MII
 #define CONFIG_CMD_DATE
 #define CONFIG_CMD_PCI
 #define CONFIG_CMD_JFFS2

 #if defined(CONFIG_SYS_RAMBOOT) && !defined(CONFIG_NAND_U_BOOT)
 	#undef CONFIG_CMD_SAVEENV
 	#undef CONFIG_CMD_LOADS
 #endif

 #define CONFIG_CMDLINE_EDITING	1
 #define CONFIG_AUTO_COMPLETE	/* add autocompletion support   */

 /*
  * Miscellaneous configurable options
  */
 #define CONFIG_SYS_LONGHELP			/* undef to save memory */
 #define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */
 #define CONFIG_SYS_PROMPT	"=> "		/* Monitor Command Prompt */
 #define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size */

 #define CONFIG_SYS_PBSIZE	(CONFIG_SYS_CBSIZE		\
 				+ sizeof(CONFIG_SYS_PROMPT)	\
 				+ 16)	/* Print Buffer Size */
 #define CONFIG_SYS_MAXARGS	16	/* max number of command args */
 				/* Boot Argument Buffer Size */
 #define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE
 #define CONFIG_SYS_HZ		1000	/* decrementer freq: 1ms ticks */

 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 256 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
 				/* Initial Memory map for Linux*/
 #define CONFIG_SYS_BOOTMAPSZ	(256 << 20)

 #define CONFIG_SYS_RCWH_PCIHOST	0x80000000	/* PCIHOST */

 #define CONFIG_SYS_HRCW_LOW	(HRCWL_LCL_BUS_TO_SCB_CLK_1X1	\
 				| 0x20000000 /* reserved */	\
 				| HRCWL_DDR_TO_SCB_CLK_2X1	\
 				| HRCWL_CSB_TO_CLKIN_4X1	\
 				| HRCWL_CORE_TO_CSB_2_5X1)

 #define CONFIG_SYS_NS16550_CLK	(CONFIG_83XX_CLKIN * 4)

 #define CONFIG_SYS_HRCW_HIGH_BASE	(HRCWH_PCI_HOST	\
 				| HRCWH_PCI1_ARBITER_ENABLE	\
 				| HRCWH_CORE_ENABLE		\
 				| HRCWH_BOOTSEQ_DISABLE		\
 				| HRCWH_SW_WATCHDOG_DISABLE	\
 				| HRCWH_TSEC1M_IN_RGMII		\
 				| HRCWH_TSEC2M_IN_RGMII		\
 				| HRCWH_BIG_ENDIAN		\
 				| HRCWH_LALE_NORMAL)

 #ifdef CONFIG_NAND_LP
 #define CONFIG_SYS_HRCW_HIGH	(CONFIG_SYS_HRCW_HIGH_BASE	\
 				| HRCWH_FROM_0XFFF00100		\
 				| HRCWH_ROM_LOC_NAND_LP_8BIT	\
 				| HRCWH_RL_EXT_NAND)
 #else
 #define CONFIG_SYS_HRCW_HIGH	(CONFIG_SYS_HRCW_HIGH_BASE	\
 				| HRCWH_FROM_0XFFF00100		\
 				| HRCWH_ROM_LOC_NAND_SP_8BIT	\
 				| HRCWH_RL_EXT_NAND)
 #endif

 /* System IO Config */
 #define CONFIG_SYS_SICRH	(SICRH_ETSEC2_B	\
 				| SICRH_ETSEC2_C	\
 				| SICRH_ETSEC2_D	\
 				| SICRH_ETSEC2_E	\
 				| SICRH_ETSEC2_F	\
 				| SICRH_ETSEC2_G	\
 				| SICRH_TSOBI1		\
 				| SICRH_TSOBI2)
 #define CONFIG_SYS_SICRL	(SICRL_LBC		\
 				| SICRL_USBDR_10	\
 				| SICRL_ETSEC2_A)

 #define CONFIG_SYS_HID0_INIT	0x000000000
 #define CONFIG_SYS_HID0_FINAL	(HID0_ENABLE_MACHINE_CHECK \
 				| HID0_ENABLE_INSTRUCTION_CACHE \
 				| HID0_ENABLE_DYNAMIC_POWER_MANAGMENT)

 #define CONFIG_SYS_HID2		HID2_HBE

 #define CONFIG_HIGH_BATS	1	/* High BATs supported */

 /* DDR @ 0x00000000 */
 #define CONFIG_SYS_IBAT0L	(CONFIG_SYS_SDRAM_BASE | BATL_PP_RW)
 #define CONFIG_SYS_IBAT0U	(CONFIG_SYS_SDRAM_BASE \
 				| BATU_BL_256M \
 				| BATU_VS \
 				| BATU_VP)
 #define CONFIG_SYS_IBAT1L	((CONFIG_SYS_SDRAM_BASE + 0x10000000) \
 				| BATL_PP_RW)
 #define CONFIG_SYS_IBAT1U	((CONFIG_SYS_SDRAM_BASE + 0x10000000) \
 				| BATU_BL_256M \
 				| BATU_VS \
 				| BATU_VP)

 /* PCI @ 0x80000000 */
 #define CONFIG_SYS_IBAT2L	(CONFIG_SYS_PCI1_MEM_BASE | BATL_PP_RW)
 #define CONFIG_SYS_IBAT2U	(CONFIG_SYS_PCI1_MEM_BASE \
 				| BATU_BL_256M \
 				| BATU_VS \
 				| BATU_VP)
 #define CONFIG_SYS_IBAT3L	(CONFIG_SYS_PCI1_MMIO_BASE \
 				| BATL_PP_RW \
 				| BATL_CACHEINHIBIT \
 				| BATL_GUARDEDSTORAGE)
 #define CONFIG_SYS_IBAT3U	(CONFIG_SYS_PCI1_MMIO_BASE \
 				| BATU_BL_256M \
 				| BATU_VS \
 				| BATU_VP)

 /* PCI2 not supported on 8313 */
 #define CONFIG_SYS_IBAT4L	(0)
 #define CONFIG_SYS_IBAT4U	(0)

 /* IMMRBAR @ 0xE0000000, PCI IO @ 0xE2000000 */
 #define CONFIG_SYS_IBAT5L	(CONFIG_SYS_IMMR \
 				| BATL_PP_RW \
 				| BATL_CACHEINHIBIT \
 				| BATL_GUARDEDSTORAGE)
 #define CONFIG_SYS_IBAT5U	(CONFIG_SYS_IMMR \
 				| BATU_BL_256M \
 				| BATU_VS \
 				| BATU_VP)

 /* SDRAM @ 0xF0000000, stack in DCACHE 0xFDF00000 & FLASH @ 0xFE000000 */
 #define CONFIG_SYS_IBAT6L	(0xF0000000 \
 				| BATL_PP_RW \
 				| BATL_GUARDEDSTORAGE)
 #define CONFIG_SYS_IBAT6U	(0xF0000000 \
 				| BATU_BL_256M \
 				| BATU_VS \
 				| BATU_VP)

 #define CONFIG_SYS_IBAT7L	(0)
 #define CONFIG_SYS_IBAT7U	(0)

 #define CONFIG_SYS_DBAT0L	CONFIG_SYS_IBAT0L
 #define CONFIG_SYS_DBAT0U	CONFIG_SYS_IBAT0U
 #define CONFIG_SYS_DBAT1L	CONFIG_SYS_IBAT1L
 #define CONFIG_SYS_DBAT1U	CONFIG_SYS_IBAT1U
 #define CONFIG_SYS_DBAT2L	CONFIG_SYS_IBAT2L
 #define CONFIG_SYS_DBAT2U	CONFIG_SYS_IBAT2U
 #define CONFIG_SYS_DBAT3L	CONFIG_SYS_IBAT3L
 #define CONFIG_SYS_DBAT3U	CONFIG_SYS_IBAT3U
 #define CONFIG_SYS_DBAT4L	CONFIG_SYS_IBAT4L
 #define CONFIG_SYS_DBAT4U	CONFIG_SYS_IBAT4U
 #define CONFIG_SYS_DBAT5L	CONFIG_SYS_IBAT5L
 #define CONFIG_SYS_DBAT5U	CONFIG_SYS_IBAT5U
 #define CONFIG_SYS_DBAT6L	CONFIG_SYS_IBAT6L
 #define CONFIG_SYS_DBAT6U	CONFIG_SYS_IBAT6U
 #define CONFIG_SYS_DBAT7L	CONFIG_SYS_IBAT7L
 #define CONFIG_SYS_DBAT7U	CONFIG_SYS_IBAT7U

 /*
  * Environment Configuration
  */
 #define CONFIG_ENV_OVERWRITE

 #define CONFIG_NETDEV		"eth1"

 #define CONFIG_HOSTNAME		simpc8313
 #define CONFIG_ROOTPATH		"/tftpboot/"
 #define CONFIG_BOOTFILE		"/tftpboot/uImage"
 				/* U-Boot image on TFTP server */
 #define CONFIG_UBOOTPATH	"u-boot-nand.bin"
 #define CONFIG_FDTFILE		"simpc8313.dtb"

 				/* default location for tftp and bootm */
 #define CONFIG_LOADADDR		500000
 #define CONFIG_BOOTDELAY	5	/* 5 second delay */
 #define CONFIG_BAUDRATE		115200

 #define CONFIG_BOOTCOMMAND	"nand read $loadaddr kernel 600000;" \
 					"bootm $loadaddr - $fdtaddr"

 #define CONFIG_EXTRA_ENV_SETTINGS \
 	"netdev=" CONFIG_NETDEV "\0"					\
 	"ethprime=TSEC1\0"						\
 	"uboot=" CONFIG_UBOOTPATH "\0"					\
 	"tftpflash=tftpboot $loadaddr $uboot; "				\
 		"protect off " __stringify(CONFIG_SYS_TEXT_BASE)	\
 			" +$filesize; "	\
 		"erase " __stringify(CONFIG_SYS_TEXT_BASE)		\
 			" +$filesize; "	\
 		"cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE)	\
 			" $filesize; "	\
 		"protect on " __stringify(CONFIG_SYS_TEXT_BASE)		\
 			" +$filesize; "	\
 		"cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE)	\
 			" $filesize\0"	\
 	"fdtaddr=ae0000\0"						\
 	"fdtfile=" CONFIG_FDTFILE "\0"					\
 	"console=ttyS0\0"						\
 	"setbootargs=setenv bootargs "					\
 		"root=$rootdev rw console=$console,$baudrate $othbootargs\0" \
 	"setipargs=setenv bootargs nfsroot=$serverip:$rootpath "	\
 		"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:"	\
 							"$netdev:off "	\
 		"root=$rootdev rw console=$console,$baudrate $othbootargs\0" \
 	"load_uboot=tftp 100000 u-boot-nand.bin\0"			\
 	"burn_uboot=nand erase u-boot 80000; "				\
 		"nand write 100000 u-boot $filesize\0"			\
 	"update_uboot=run load_uboot;run burn_uboot\0"			\
 	"mtdids=nand0=nand0\0"						\
 	"mtdparts=mtdparts=nand0:2M(u-boot),6M(kernel),-(jffs2)\0"	\
 	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
 		"nfsroot=${serverip}:${rootpath}\0"			\
 	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
 	"addip=setenv bootargs ${bootargs} "				\
 		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
 		":${hostname}:${netdev}:off panic=1\0"			\
 	"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0" \
 	"bootargs=root=/dev/mtdblock2 rootfstype=jffs2 rw "		\
 		"console=ttyS0,115200\0"				\
 	""

 #define CONFIG_NFSBOOTCOMMAND						\
 	"setenv rootdev /dev/nfs;"					\
 	"run setbootargs;"						\
 	"run setipargs;"						\
 	"tftp $loadaddr $bootfile;"					\
 	"tftp $fdtaddr $fdtfile;"					\
 	"bootm $loadaddr - $fdtaddr"

 #define CONFIG_RAMBOOTCOMMAND						\
 	"setenv rootdev /dev/ram;"					\
 	"run setbootargs;"						\
 	"tftp $ramdiskaddr $ramdiskfile;"				\
 	"tftp $loadaddr $bootfile;"					\
 	"tftp $fdtaddr $fdtfile;"					\
 	"bootm $loadaddr $ramdiskaddr $fdtaddr"

 #endif	/* __CONFIG_H */
	/*
	* Copyright (C) Sheldon Instruments, Inc. 2008
	*
	* SPDX-License-Identifier: GPL-2.0+
	*/
	/*
	* simpc8313 board configuration file
	*/

	#ifndef __CONFIG_H
	#define __CONFIG_H

	/*
	* High Level Configuration Options
	*/
	#define CONFIG_NAND_U_BOOT

	#define CONFIG_E300 1
	#define CONFIG_MPC83xx 1
	#define CONFIG_MPC831x 1
	#define CONFIG_MPC8313 1

	#define CONFIG_SYS_NAND_U_BOOT_SIZE (512 << 10)
	#define CONFIG_SYS_NAND_U_BOOT_DST 0x00100000
	#define CONFIG_SYS_NAND_U_BOOT_START 0x00100100
	#define CONFIG_SYS_NAND_U_BOOT_RELOC 0x00010000
	#define CONFIG_SYS_NAND_U_BOOT_RELOC_SP (CONFIG_SYS_NAND_U_BOOT_RELOC + 0x10000)

	#define CONFIG_SYS_TEXT_BASE 0x00100000 /* CONFIG_SYS_NAND_U_BOOT_DST */
	#define CONFIG_SYS_TEXT_BASE_SPL 0xfff00000

	#ifdef CONFIG_NAND_SPL
	#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE_SPL /* start of monitor */
	#else
	#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
	#endif

	#define CONFIG_PCI
	#define CONFIG_PCI_INDIRECT_BRIDGE
	#define CONFIG_FSL_ELBC 1

	#define CONFIG_MISC_INIT_R

	/*
	* On-board devices
	*
	* TSEC1 is Marvell PHY 88E1118
	*/

	#define CONFIG_SYS_33MHZ

	#define CONFIG_83XX_CLKIN 33333333 /* in Hz */

	#define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN

	#define CONFIG_SYS_IMMR 0xE0000000

	#if defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
	#define CONFIG_DEFAULT_IMMR CONFIG_SYS_IMMR
	#endif

	#define CONFIG_SYS_MEMTEST_START 0x00001000
	#define CONFIG_SYS_MEMTEST_END 0x07f00000

	#define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth (0-3) */
	#define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count (0-7) */

	/*
	* Device configurations
	*/
	#define CONFIG_TSEC1

	/*
	* DDR Setup
	*/
	/* DDR is system memory*/
	#define CONFIG_SYS_DDR_BASE 0x00000000
	#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE
	#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE

	#define CONFIG_VERY_BIG_RAM
	#define CONFIG_MAX_MEM_MAPPED (512 << 20)

	#define CONFIG_SYS_DDRCDR (DDRCDR_EN \
	\| DDRCDR_PZ_NOMZ \
	\| DDRCDR_NZ_NOMZ \
	\| DDRCDR_M_ODR)
	/* 0x73000002 TODO ODR & DRN ? */

	/*
	* FLASH on the Local Bus
	*/
	#define CONFIG_SYS_NO_FLASH

	#if !defined(CONFIG_NAND_SPL)
	#define CONFIG_SYS_RAMBOOT
	#endif

	#define CONFIG_SYS_INIT_RAM_LOCK 1
	#define CONFIG_SYS_INIT_RAM_ADDR 0xFD000000 /* Initial RAM address */
	#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM*/

	#define CONFIG_SYS_GBL_DATA_OFFSET \
	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
	#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET

	/* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */
	#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
	#define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */

	/*
	* Local Bus LCRR and LBCR regs
	*/
	#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
	#define CONFIG_SYS_LCRR_EADC LCRR_EADC_1
	#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2
	#define CONFIG_SYS_LBC_LBCR (0x00040000 /* TODO */ \
	\| (0xFF << LBCR_BMT_SHIFT) \
	\| 0xF) /* 0x0004ff0f */

	/* LB refresh timer prescal, 266MHz/32 */
	#define CONFIG_SYS_LBC_MRTPR 0x20000000

	/* drivers/mtd/nand/nand.c */
	#ifdef CONFIG_NAND_SPL
	#define CONFIG_SYS_NAND_BASE 0xFFF00000
	#else
	#define CONFIG_SYS_NAND_BASE 0xE2800000
	#endif
	#define CONFIG_SYS_FPGA_BASE 0xFF000000

	#define CONFIG_CMD_NAND
	#define CONFIG_SYS_MAX_NAND_DEVICE 1
	#define CONFIG_MTD_NAND_VERIFY_WRITE
	#define CONFIG_NAND_FSL_ELBC 1

	#define CONFIG_SYS_NAND_BR_PRELIM (CONFIG_SYS_NAND_BASE \
	\| BR_DECC_CHK_GEN /* Use HW ECC */ \
	\| BR_PS_8 /* 8 bit Port */ \
	\| BR_MS_FCM /* MSEL = FCM */ \
	\| BR_V) /* valid */

	#ifdef CONFIG_NAND_SP
	#define CONFIG_SYS_NAND_OR_PRELIM (OR_AM_32KB \
	\| OR_FCM_CSCT \
	\| OR_FCM_CST \
	\| OR_FCM_CHT \
	\| OR_FCM_SCY_1 \
	\| OR_FCM_TRLX \
	\| OR_FCM_EHTR)
	#define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN \| LBLAWAR_32KB)
	#define CONFIG_SYS_NAND_PAGE_SIZE 512 /* NAND chip page size */
	/* NAND chip block size */
	#define CONFIG_SYS_NAND_BLOCK_SIZE (16 << 10)
	#define NAND_CACHE_PAGES 32
	#elif defined(CONFIG_NAND_LP)
	#define CONFIG_SYS_NAND_OR_PRELIM (OR_AM_256KB \
	\| OR_FCM_PGS \
	\| OR_FCM_CSCT \
	\| OR_FCM_CST \
	\| OR_FCM_CHT \
	\| OR_FCM_SCY_1 \
	\| OR_FCM_TRLX \
	\| OR_FCM_EHTR)
	#define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN \| LBLAWAR_256KB)
	#define CONFIG_SYS_NAND_PAGE_SIZE 2048 /* NAND chip page size */
	/* NAND chip block size */
	#define CONFIG_SYS_NAND_BLOCK_SIZE (128 << 10)
	#define NAND_CACHE_PAGES 64
	#else
	#error Page size of NAND not defined.
	#endif /* CONFIG_NAND_SP */

	#define CONFIG_SYS_NAND_U_BOOT_OFFS CONFIG_SYS_NAND_BLOCK_SIZE

	#define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NAND_BR_PRELIM
	#define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NAND_OR_PRELIM

	#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_NAND_BASE

	#define CONFIG_SYS_NAND_LBLAWBAR_PRELIM CONFIG_SYS_LBLAWBAR0_PRELIM
	#define CONFIG_SYS_NAND_LBLAWAR_PRELIM CONFIG_SYS_LBLAWAR0_PRELIM

	#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_FPGA_BASE \
	\| BR_PS_16 \
	\| BR_MS_UPMA \
	\| BR_V)
	#define CONFIG_SYS_OR1_PRELIM (OR_AM_2MB \
	\| OR_UPM_BCTLD)

	#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_FPGA_BASE
	#define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN \| LBLAWAR_2MB)

	/*
	* JFFS2 configuration
	*/
	#define CONFIG_JFFS2_NAND
	#define CONFIG_JFFS2_DEV "nand0"

	/* mtdparts command line support */
	#define CONFIG_CMD_MTDPARTS
	#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
	#define MTDIDS_DEFAULT "nand0=nand0"
	#define MTDPARTS_DEFAULT "mtdparts=nand0:2M(u-boot),6M(kernel),-(jffs2)"

	/* pass open firmware flat tree */
	#define CONFIG_OF_LIBFDT 1
	#define CONFIG_OF_BOARD_SETUP 1
	#define CONFIG_OF_STDOUT_VIA_ALIAS 1

	/*
	* Serial Port
	*/
	#define CONFIG_CONS_INDEX 1
	#define CONFIG_SYS_NS16550
	#define CONFIG_SYS_NS16550_SERIAL
	#define CONFIG_SYS_NS16550_REG_SIZE 1
	#ifdef CONFIG_NAND_SPL
	#define CONFIG_NS16550_MIN_FUNCTIONS
	#endif

	#define CONFIG_SYS_BAUDRATE_TABLE \
	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}

	#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
	#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)

	/* Use the HUSH parser */
	#define CONFIG_SYS_HUSH_PARSER

	/* I2C */
	#define CONFIG_HARD_I2C /* I2C with hardware support*/
	#define CONFIG_FSL_I2C
	#define CONFIG_I2C_MULTI_BUS
	#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
	#define CONFIG_SYS_I2C_SLAVE 0x7F
	#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } /* Don't probe these addrs */
	#define CONFIG_SYS_I2C_OFFSET 0x3000
	#define CONFIG_SYS_I2C2_OFFSET 0x3100

	/*
	* General PCI
	* Addresses are mapped 1-1.
	*/
	#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000
	#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE
	#define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */
	#define CONFIG_SYS_PCI1_MMIO_BASE 0x90000000
	#define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE
	#define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000 /* 256M */
	#define CONFIG_SYS_PCI1_IO_BASE 0x00000000
	#define CONFIG_SYS_PCI1_IO_PHYS 0xE2000000
	#define CONFIG_SYS_PCI1_IO_SIZE 0x00100000 /* 1M */

	#define CONFIG_PCI_PNP /* do pci plug-and-play */
	#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */

	/*
	* TSEC
	*/
	#define CONFIG_TSEC_ENET /* TSEC ethernet support */

	#define CONFIG_GMII /* MII PHY management */

	#ifdef CONFIG_TSEC1
	#define CONFIG_HAS_ETH0
	#define CONFIG_TSEC1_NAME "TSEC0"
	#define CONFIG_SYS_TSEC1_OFFSET 0x24000
	#define TSEC1_PHY_ADDR 0x0
	#define TSEC1_FLAGS TSEC_GIGABIT
	#define TSEC1_PHYIDX 0
	#endif

	#ifdef CONFIG_TSEC2
	#define CONFIG_HAS_ETH1
	#define CONFIG_TSEC2_NAME "TSEC1"
	#define CONFIG_SYS_TSEC2_OFFSET 0x25000
	#define TSEC2_PHY_ADDR 4
	#define TSEC2_FLAGS TSEC_GIGABIT
	#define TSEC2_PHYIDX 0
	#endif


	/* Options are: TSEC[0-1] */
	#define CONFIG_ETHPRIME "TSEC1"

	/*
	* Configure on-board RTC
	*/
	#define CONFIG_RTC_DS1337
	#define CONFIG_SYS_I2C_RTC_ADDR 0x68

	/*
	* Environment
	*/
	#if defined(CONFIG_NAND_U_BOOT)
	#define CONFIG_ENV_IS_IN_NAND 1
	#define CONFIG_ENV_OFFSET (768 * 1024)
	#define CONFIG_ENV_SECT_SIZE CONFIG_SYS_NAND_BLOCK_SIZE
	#define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE
	#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
	#define CONFIG_ENV_RANGE (CONFIG_ENV_SECT_SIZE * 4)
	#define CONFIG_ENV_OFFSET_REDUND \
	(CONFIG_ENV_OFFSET + CONFIG_ENV_RANGE)
	#elif !defined(CONFIG_SYS_RAMBOOT)
	#define CONFIG_ENV_IS_IN_FLASH 1
	#define CONFIG_ENV_ADDR \
	(CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
	#define CONFIG_ENV_SECT_SIZE 0x10000 /* 64K(one sector) for env */
	#define CONFIG_ENV_SIZE 0x2000

	/* Address and size of Redundant Environment Sector */
	#else
	#define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
	#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
	#define CONFIG_ENV_SIZE 0x2000
	#endif

	#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
	#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */

	/*
	* BOOTP options
	*/
	#define CONFIG_BOOTP_BOOTFILESIZE
	#define CONFIG_BOOTP_BOOTPATH
	#define CONFIG_BOOTP_GATEWAY
	#define CONFIG_BOOTP_HOSTNAME


	/*
	* Command line configuration.
	*/
	#include <config_cmd_default.h>
	#undef CONFIG_CMD_IMLS
	#undef CONFIG_CMD_FLASH

	#define CONFIG_CMD_PING
	#define CONFIG_CMD_DHCP
	#define CONFIG_CMD_I2C
	#define CONFIG_CMD_MII
	#define CONFIG_CMD_DATE
	#define CONFIG_CMD_PCI
	#define CONFIG_CMD_JFFS2

	#if defined(CONFIG_SYS_RAMBOOT) && !defined(CONFIG_NAND_U_BOOT)
	#undef CONFIG_CMD_SAVEENV
	#undef CONFIG_CMD_LOADS
	#endif

	#define CONFIG_CMDLINE_EDITING 1
	#define CONFIG_AUTO_COMPLETE /* add autocompletion support */

	/*
	* Miscellaneous configurable options
	*/
	#define CONFIG_SYS_LONGHELP /* undef to save memory */
	#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
	#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
	#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */

	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \
	+ sizeof(CONFIG_SYS_PROMPT) \
	+ 16) /* Print Buffer Size */
	#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
	/* Boot Argument Buffer Size */
	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
	#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */

	/*
	* For booting Linux, the board info and command line data
	* have to be in the first 256 MB of memory, since this is
	* the maximum mapped by the Linux kernel during initialization.
	*/
	/* Initial Memory map for Linux*/
	#define CONFIG_SYS_BOOTMAPSZ (256 << 20)

	#define CONFIG_SYS_RCWH_PCIHOST 0x80000000 /* PCIHOST */

	#define CONFIG_SYS_HRCW_LOW (HRCWL_LCL_BUS_TO_SCB_CLK_1X1 \
	\| 0x20000000 /* reserved */ \
	\| HRCWL_DDR_TO_SCB_CLK_2X1 \
	\| HRCWL_CSB_TO_CLKIN_4X1 \
	\| HRCWL_CORE_TO_CSB_2_5X1)

	#define CONFIG_SYS_NS16550_CLK (CONFIG_83XX_CLKIN * 4)

	#define CONFIG_SYS_HRCW_HIGH_BASE (HRCWH_PCI_HOST \
	\| HRCWH_PCI1_ARBITER_ENABLE \
	\| HRCWH_CORE_ENABLE \
	\| HRCWH_BOOTSEQ_DISABLE \
	\| HRCWH_SW_WATCHDOG_DISABLE \
	\| HRCWH_TSEC1M_IN_RGMII \
	\| HRCWH_TSEC2M_IN_RGMII \
	\| HRCWH_BIG_ENDIAN \
	\| HRCWH_LALE_NORMAL)

	#ifdef CONFIG_NAND_LP
	#define CONFIG_SYS_HRCW_HIGH (CONFIG_SYS_HRCW_HIGH_BASE \
	\| HRCWH_FROM_0XFFF00100 \
	\| HRCWH_ROM_LOC_NAND_LP_8BIT \
	\| HRCWH_RL_EXT_NAND)
	#else
	#define CONFIG_SYS_HRCW_HIGH (CONFIG_SYS_HRCW_HIGH_BASE \
	\| HRCWH_FROM_0XFFF00100 \
	\| HRCWH_ROM_LOC_NAND_SP_8BIT \
	\| HRCWH_RL_EXT_NAND)
	#endif

	/* System IO Config */
	#define CONFIG_SYS_SICRH (SICRH_ETSEC2_B \
	\| SICRH_ETSEC2_C \
	\| SICRH_ETSEC2_D \
	\| SICRH_ETSEC2_E \
	\| SICRH_ETSEC2_F \
	\| SICRH_ETSEC2_G \
	\| SICRH_TSOBI1 \
	\| SICRH_TSOBI2)
	#define CONFIG_SYS_SICRL (SICRL_LBC \
	\| SICRL_USBDR_10 \
	\| SICRL_ETSEC2_A)

	#define CONFIG_SYS_HID0_INIT 0x000000000
	#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK \
	\| HID0_ENABLE_INSTRUCTION_CACHE \
	\| HID0_ENABLE_DYNAMIC_POWER_MANAGMENT)

	#define CONFIG_SYS_HID2 HID2_HBE

	#define CONFIG_HIGH_BATS 1 /* High BATs supported */

	/* DDR @ 0x00000000 */
	#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE \| BATL_PP_RW)
	#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE \
	\| BATU_BL_256M \
	\| BATU_VS \
	\| BATU_VP)
	#define CONFIG_SYS_IBAT1L ((CONFIG_SYS_SDRAM_BASE + 0x10000000) \
	\| BATL_PP_RW)
	#define CONFIG_SYS_IBAT1U ((CONFIG_SYS_SDRAM_BASE + 0x10000000) \
	\| BATU_BL_256M \
	\| BATU_VS \
	\| BATU_VP)

	/* PCI @ 0x80000000 */
	#define CONFIG_SYS_IBAT2L (CONFIG_SYS_PCI1_MEM_BASE \| BATL_PP_RW)
	#define CONFIG_SYS_IBAT2U (CONFIG_SYS_PCI1_MEM_BASE \
	\| BATU_BL_256M \
	\| BATU_VS \
	\| BATU_VP)
	#define CONFIG_SYS_IBAT3L (CONFIG_SYS_PCI1_MMIO_BASE \
	\| BATL_PP_RW \
	\| BATL_CACHEINHIBIT \
	\| BATL_GUARDEDSTORAGE)
	#define CONFIG_SYS_IBAT3U (CONFIG_SYS_PCI1_MMIO_BASE \
	\| BATU_BL_256M \
	\| BATU_VS \
	\| BATU_VP)

	/* PCI2 not supported on 8313 */
	#define CONFIG_SYS_IBAT4L (0)
	#define CONFIG_SYS_IBAT4U (0)

	/* IMMRBAR @ 0xE0000000, PCI IO @ 0xE2000000 */
	#define CONFIG_SYS_IBAT5L (CONFIG_SYS_IMMR \
	\| BATL_PP_RW \
	\| BATL_CACHEINHIBIT \
	\| BATL_GUARDEDSTORAGE)
	#define CONFIG_SYS_IBAT5U (CONFIG_SYS_IMMR \
	\| BATU_BL_256M \
	\| BATU_VS \
	\| BATU_VP)

	/* SDRAM @ 0xF0000000, stack in DCACHE 0xFDF00000 & FLASH @ 0xFE000000 */
	#define CONFIG_SYS_IBAT6L (0xF0000000 \
	\| BATL_PP_RW \
	\| BATL_GUARDEDSTORAGE)
	#define CONFIG_SYS_IBAT6U (0xF0000000 \
	\| BATU_BL_256M \
	\| BATU_VS \
	\| BATU_VP)

	#define CONFIG_SYS_IBAT7L (0)
	#define CONFIG_SYS_IBAT7U (0)

	#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
	#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
	#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
	#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
	#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L
	#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
	#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L
	#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
	#define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L
	#define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U
	#define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L
	#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U
	#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L
	#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U
	#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L
	#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U

	/*
	* Environment Configuration
	*/
	#define CONFIG_ENV_OVERWRITE

	#define CONFIG_NETDEV "eth1"

	#define CONFIG_HOSTNAME simpc8313
	#define CONFIG_ROOTPATH "/tftpboot/"
	#define CONFIG_BOOTFILE "/tftpboot/uImage"
	/* U-Boot image on TFTP server */
	#define CONFIG_UBOOTPATH "u-boot-nand.bin"
	#define CONFIG_FDTFILE "simpc8313.dtb"

	/* default location for tftp and bootm */
	#define CONFIG_LOADADDR 500000
	#define CONFIG_BOOTDELAY 5 /* 5 second delay */
	#define CONFIG_BAUDRATE 115200

	#define CONFIG_BOOTCOMMAND "nand read $loadaddr kernel 600000;" \
	"bootm $loadaddr - $fdtaddr"

	#define CONFIG_EXTRA_ENV_SETTINGS \
	"netdev=" CONFIG_NETDEV "\0" \
	"ethprime=TSEC1\0" \
	"uboot=" CONFIG_UBOOTPATH "\0" \
	"tftpflash=tftpboot $loadaddr $uboot; " \
	"protect off " __stringify(CONFIG_SYS_TEXT_BASE) \
	" +$filesize; " \
	"erase " __stringify(CONFIG_SYS_TEXT_BASE) \
	" +$filesize; " \
	"cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \
	" $filesize; " \
	"protect on " __stringify(CONFIG_SYS_TEXT_BASE) \
	" +$filesize; " \
	"cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \
	" $filesize\0" \
	"fdtaddr=ae0000\0" \
	"fdtfile=" CONFIG_FDTFILE "\0" \
	"console=ttyS0\0" \
	"setbootargs=setenv bootargs " \
	"root=$rootdev rw console=$console,$baudrate $othbootargs\0" \
	"setipargs=setenv bootargs nfsroot=$serverip:$rootpath " \
	"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:" \
	"$netdev:off " \
	"root=$rootdev rw console=$console,$baudrate $othbootargs\0" \
	"load_uboot=tftp 100000 u-boot-nand.bin\0" \
	"burn_uboot=nand erase u-boot 80000; " \
	"nand write 100000 u-boot $filesize\0" \
	"update_uboot=run load_uboot;run burn_uboot\0" \
	"mtdids=nand0=nand0\0" \
	"mtdparts=mtdparts=nand0:2M(u-boot),6M(kernel),-(jffs2)\0" \
	"nfsargs=setenv bootargs root=/dev/nfs rw " \
	"nfsroot=${serverip}:${rootpath}\0" \
	"ramargs=setenv bootargs root=/dev/ram rw\0" \
	"addip=setenv bootargs ${bootargs} " \
	"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
	":${hostname}:${netdev}:off panic=1\0" \
	"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0" \
	"bootargs=root=/dev/mtdblock2 rootfstype=jffs2 rw " \
	"console=ttyS0,115200\0" \
	""

	#define CONFIG_NFSBOOTCOMMAND \
	"setenv rootdev /dev/nfs;" \
	"run setbootargs;" \
	"run setipargs;" \
	"tftp $loadaddr $bootfile;" \
	"tftp $fdtaddr $fdtfile;" \
	"bootm $loadaddr - $fdtaddr"

	#define CONFIG_RAMBOOTCOMMAND \
	"setenv rootdev /dev/ram;" \
	"run setbootargs;" \
	"tftp $ramdiskaddr $ramdiskfile;" \
	"tftp $loadaddr $bootfile;" \
	"tftp $fdtaddr $fdtfile;" \
	"bootm $loadaddr $ramdiskaddr $fdtaddr"

	#endif /* __CONFIG_H */