| /* |
| * (C) Copyright 2004 |
| * Elmeg Communications Systems GmbH, Juergen Selent (j.selent@elmeg.de) |
| * |
| * Support for the Elmeg VoVPN Gateway Module |
| * |
| * This program is free software; you can redistribute it and/or |
| * modify it under the terms of the GNU General Public License as |
| * published by the Free Software Foundation; either version 2 of |
| * the License, or (at your option) any later version. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 59 Temple Place, Suite 330, Boston, |
| * MA 02111-1307 USA |
| */ |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| /* define cpu used */ |
| #define CONFIG_MPC8272 1 |
| |
| /* define busmode: 8260 */ |
| #undef CONFIG_BUSMODE_60x |
| |
| /* system clock rate (CLKIN) - equal to the 60x and local bus speed */ |
| #ifdef CONFIG_CLKIN_66MHz |
| #define CONFIG_8260_CLKIN 66666666 /* in Hz */ |
| #else |
| #define CONFIG_8260_CLKIN 100000000 /* in Hz */ |
| #endif |
| |
| /* call board_early_init_f */ |
| #define CONFIG_BOARD_EARLY_INIT_F 1 |
| |
| /* have misc_init_r() function */ |
| #define CONFIG_MISC_INIT_R 1 |
| |
| /* have reset_phy_r() function */ |
| #define CONFIG_RESET_PHY_R 1 |
| |
| /* have special reset function */ |
| #define CONFIG_HAVE_OWN_RESET 1 |
| |
| /* allow serial and ethaddr to be overwritten */ |
| #define CONFIG_ENV_OVERWRITE |
| |
| /* watchdog disabled */ |
| #undef CONFIG_WATCHDOG |
| |
| /* include support for bzip2 compressed images */ |
| #undef CONFIG_BZIP2 |
| |
| /* status led */ |
| #undef CONFIG_STATUS_LED /* XXX jse */ |
| |
| /* vendor parameter protection */ |
| #define CONFIG_ENV_OVERWRITE |
| |
| /* |
| * select serial console configuration |
| * |
| * if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then |
| * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4 |
| * for SCC). |
| */ |
| #define CONFIG_CONS_ON_SMC |
| #undef CONFIG_CONS_ON_SCC |
| #undef CONFIG_CONS_NONE |
| #define CONFIG_CONS_INDEX 1 |
| |
| /* serial port default baudrate */ |
| #define CONFIG_BAUDRATE 115200 |
| |
| /* echo on for serial download */ |
| #define CONFIG_LOADS_ECHO 1 |
| |
| /* don't allow baudrate change */ |
| #undef CONFIG_SYS_LOADS_BAUD_CHANGE |
| |
| /* supported baudrates */ |
| #define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } |
| |
| /* |
| * select ethernet configuration |
| * |
| * if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then |
| * CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3 |
| * for FCC) |
| * |
| * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be |
| * defined elsewhere (as for the console), or CONFIG_CMD_NET must be unset. |
| */ |
| #undef CONFIG_ETHER_ON_SCC |
| #define CONFIG_ETHER_ON_FCC |
| #undef CONFIG_ETHER_NONE |
| |
| #ifdef CONFIG_ETHER_ON_FCC |
| |
| /* which SCC/FCC channel for ethernet */ |
| #define CONFIG_ETHER_INDEX 1 |
| |
| /* Marvell Switch SMI base addr */ |
| #define CONFIG_SYS_PHY_ADDR 0x10 |
| |
| /* FCC1 RMII REFCLK is CLK10 */ |
| #define CONFIG_SYS_CMXFCR_VALUE CMXFCR_TF1CS_CLK10 |
| #define CONFIG_SYS_CMXFCR_MASK (CMXFCR_FC1|CMXFCR_TF1CS_MSK) |
| |
| /* BDs and buffers on 60x bus */ |
| #define CONFIG_SYS_CPMFCR_RAMTYPE 0 |
| |
| /* Local Protect, Full duplex, Flowcontrol, RMII */ |
| #define CONFIG_SYS_FCC_PSMR (FCC_PSMR_LPB|FCC_PSMR_FDE|\ |
| FCC_PSMR_FCE|FCC_PSMR_RMII) |
| |
| /* bit-bang MII PHY management */ |
| #define CONFIG_BITBANGMII |
| |
| #define MDIO_PORT 1 /* Port B */ |
| #define CONFIG_SYS_MDIO_PIN 0x00002000 /* PB18 */ |
| #define CONFIG_SYS_MDC_PIN 0x00001000 /* PB19 */ |
| #define MDIO_ACTIVE (iop->pdir |= CONFIG_SYS_MDIO_PIN) |
| #define MDIO_TRISTATE (iop->pdir &= ~CONFIG_SYS_MDIO_PIN) |
| #define MDIO_READ ((iop->pdat & CONFIG_SYS_MDIO_PIN) != 0) |
| #define MDIO(bit) if(bit) iop->pdat |= CONFIG_SYS_MDIO_PIN; \ |
| else iop->pdat &= ~CONFIG_SYS_MDIO_PIN |
| #define MDC(bit) if(bit) iop->pdat |= CONFIG_SYS_MDC_PIN; \ |
| else iop->pdat &= ~CONFIG_SYS_MDC_PIN |
| #define MIIDELAY udelay(1) |
| |
| #endif |
| |
| /* |
| * BOOTP options |
| */ |
| #define CONFIG_BOOTP_BOOTFILESIZE |
| #define CONFIG_BOOTP_BOOTPATH |
| #define CONFIG_BOOTP_GATEWAY |
| #define CONFIG_BOOTP_HOSTNAME |
| |
| |
| /* |
| * Command line configuration. |
| */ |
| |
| #define CONFIG_CMD_AUTOSCRIPT |
| #define CONFIG_CMD_BDI |
| #define CONFIG_CMD_CONSOLE |
| #define CONFIG_CMD_ECHO |
| #define CONFIG_CMD_SAVEENV |
| #define CONFIG_CMD_FLASH |
| #define CONFIG_CMD_IMI |
| #define CONFIG_CMD_IMLS |
| #define CONFIG_CMD_LOADB |
| #define CONFIG_CMD_MEMORY |
| #define CONFIG_CMD_MISC |
| #define CONFIG_CMD_NET |
| #define CONFIG_CMD_PING |
| #define CONFIG_CMD_RUN |
| |
| |
| /* |
| * boot options & environment |
| */ |
| #define CONFIG_BOOTDELAY 3 |
| #define CONFIG_BOOTCOMMAND "run flash_self" |
| #undef CONFIG_BOOTARGS |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| "clean_nv=erase fff20000 ffffffff\0" \ |
| "update_boss=tftp 100000 PPC/logic157.bin; protect off fff00000 ffffffff; erase fff00000 ffffffff; cp.b 100000 fff00000 ${filesize}; tftp 100000 PPC/bootmon157.bin; cp.b 100000 fff20000 ${filesize}\0" \ |
| "update_lx=tftp 100000 ${kernel}; erase ${kernel_addr} ffefffff; cp.b 100000 ${kernel_addr} ${filesize}\0" \ |
| "update_fs=tftp 100000 ${fs}.${fstype}; erase ff840000 ffdfffff; cp.b 100000 ff840000 ${filesize}\0" \ |
| "update_ub=tftp 100000 ${uboot}; protect off fff00000 fff1ffff; erase fff00000 fff1ffff; cp.b 100000 fff00000 ${filesize}; protect off ff820000 ff83ffff; erase ff820000 ff83ffff\0" \ |
| "flashargs=setenv bootargs root=${rootdev} rw rootfstype=${fstype}\0" \ |
| "nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath}\0" \ |
| "addip=setenv bootargs ${bootargs} ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}:${netdev}:off\0" \ |
| "addmisc=setenv bootargs ${bootargs} console=${console},${baudrate} ethaddr=${ethaddr} panic=1\0" \ |
| "net_nfs=tftpboot 400000 ${kernel}; run nfsargs addip addmisc; bootm\0" \ |
| "net_self=tftpboot 400000 ${kernel}; run flashargs addmisc; bootm\0" \ |
| "flash_self=run flashargs addmisc; bootm ${kernel_addr}\0" \ |
| "flash_nfs=run nfsargs addip addmisc; bootm ${kernel_addr}\0" \ |
| "fstype=cramfs\0" \ |
| "rootpath=/root_fs\0" \ |
| "uboot=PPC/u-boot.bin\0" \ |
| "kernel=PPC/uImage\0" \ |
| "kernel_addr=ffe00000\0" \ |
| "fs=PPC/root_fs\0" \ |
| "console=ttyS0\0" \ |
| "netdev=eth0\0" \ |
| "rootdev=31:3\0" \ |
| "ethaddr=00:09:4f:01:02:03\0" \ |
| "ipaddr=10.0.0.201\0" \ |
| "netmask=255.255.255.0\0" \ |
| "serverip=10.0.0.136\0" \ |
| "gatewayip=10.0.0.10\0" \ |
| "hostname=bastard\0" \ |
| "" |
| |
| |
| /* |
| * miscellaneous configurable options |
| */ |
| |
| /* undef to save memory */ |
| #define CONFIG_SYS_LONGHELP |
| |
| /* monitor command prompt */ |
| #define CONFIG_SYS_PROMPT "=> " |
| |
| /* console i/o buffer size */ |
| #if defined(CONFIG_CMD_KGDB) |
| #define CONFIG_SYS_CBSIZE 1024 |
| #else |
| #define CONFIG_SYS_CBSIZE 256 |
| #endif |
| |
| /* print buffer size */ |
| #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) |
| |
| /* max number of command args */ |
| #define CONFIG_SYS_MAXARGS 16 |
| |
| /* boot argument buffer size */ |
| #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE |
| |
| /* memtest works on */ |
| #define CONFIG_SYS_MEMTEST_START 0x00100000 |
| /* 1 ... 15 MB in DRAM */ |
| #define CONFIG_SYS_MEMTEST_END 0x00f00000 |
| /* full featured memtest */ |
| #define CONFIG_SYS_ALT_MEMTEST |
| |
| /* default load address */ |
| #define CONFIG_SYS_LOAD_ADDR 0x00100000 |
| |
| /* decrementer freq: 1 ms ticks */ |
| #define CONFIG_SYS_HZ 1000 |
| |
| /* configure flash */ |
| #define CONFIG_SYS_FLASH_BASE 0xff800000 |
| #define CONFIG_SYS_MAX_FLASH_BANKS 1 |
| #define CONFIG_SYS_MAX_FLASH_SECT 64 |
| #define CONFIG_SYS_FLASH_SIZE 8 |
| #undef CONFIG_SYS_FLASH_16BIT |
| #define CONFIG_SYS_FLASH_ERASE_TOUT 240000 |
| #define CONFIG_SYS_FLASH_WRITE_TOUT 500 |
| #define CONFIG_SYS_FLASH_LOCK_TOUT 500 |
| #define CONFIG_SYS_FLASH_UNLOCK_TOUT 10000 |
| #define CONFIG_SYS_FLASH_PROTECTION |
| |
| /* monitor in flash */ |
| #define CONFIG_SYS_MONITOR_OFFSET 0x00700000 |
| |
| /* environment in flash */ |
| #define CONFIG_ENV_IS_IN_FLASH 1 |
| #define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00020000) |
| #define CONFIG_ENV_SIZE 0x00020000 |
| #define CONFIG_ENV_SECT_SIZE 0x00020000 |
| |
| /* |
| * Initial memory map for linux |
| * For booting Linux, the board info and command line data |
| * have to be in the first 8 MB of memory, since this is |
| * the maximum mapped by the Linux kernel during initialization. |
| */ |
| #define CONFIG_SYS_BOOTMAPSZ (8 << 20) |
| |
| /* hard reset configuration words */ |
| #ifdef CONFIG_CLKIN_66MHz |
| #define CONFIG_SYS_HRCW_MASTER 0x04643050 |
| #else |
| #error NO HRCW FOR 100MHZ SPECIFIED !!! |
| #endif |
| #define CONFIG_SYS_HRCW_SLAVE1 0x00000000 |
| #define CONFIG_SYS_HRCW_SLAVE2 0x00000000 |
| #define CONFIG_SYS_HRCW_SLAVE3 0x00000000 |
| #define CONFIG_SYS_HRCW_SLAVE4 0x00000000 |
| #define CONFIG_SYS_HRCW_SLAVE5 0x00000000 |
| #define CONFIG_SYS_HRCW_SLAVE6 0x00000000 |
| #define CONFIG_SYS_HRCW_SLAVE7 0x00000000 |
| |
| /* internal memory mapped register */ |
| #define CONFIG_SYS_IMMR 0xF0000000 |
| |
| /* definitions for initial stack pointer and data area (in DPRAM) */ |
| #define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR |
| #define CONFIG_SYS_INIT_RAM_END 0x2000 |
| #define CONFIG_SYS_GBL_DATA_SIZE 128 |
| #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) |
| #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET |
| |
| /* |
| * Start addresses for the final memory configuration |
| * (Set up by the startup code) |
| * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 |
| */ |
| #define CONFIG_SYS_SDRAM_BASE 0x00000000 |
| #define CONFIG_SYS_SDRAM_SIZE (32*1024*1024) |
| #define CONFIG_SYS_MONITOR_BASE TEXT_BASE |
| #define CONFIG_SYS_MONITOR_FLASH (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_OFFSET) |
| #define CONFIG_SYS_MONITOR_LEN 0x00020000 |
| #define CONFIG_SYS_MALLOC_LEN 0x00020000 |
| |
| /* boot flags */ |
| #define BOOTFLAG_COLD 0x01 /* normal power-on */ |
| #define BOOTFLAG_WARM 0x02 /* software reboot */ |
| |
| /* cache configuration */ |
| #define CONFIG_SYS_CACHELINE_SIZE 32 /* for MPC8260 */ |
| #if defined(CONFIG_CMD_KGDB) |
| #define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of above */ |
| #endif |
| |
| /* |
| * HIDx - Hardware Implementation-dependent Registers |
| *----------------------------------------------------------------------- |
| * HID0 also contains cache control - initially enable both caches and |
| * invalidate contents, then the final state leaves only the instruction |
| * cache enabled. Note that Power-On and Hard reset invalidate the caches, |
| * but Soft reset does not. |
| * |
| * HID1 has only read-only information - nothing to set. |
| */ |
| #define CONFIG_SYS_HID0_INIT (HID0_ICE|HID0_DCE|\ |
| HID0_ICFI|HID0_DCI|HID0_IFEM|HID0_ABE) |
| #define CONFIG_SYS_HID0_FINAL (HID0_IFEM|HID0_ABE) |
| #define CONFIG_SYS_HID2 0 |
| |
| /* RMR - reset mode register - turn on checkstop reset enable */ |
| #define CONFIG_SYS_RMR RMR_CSRE |
| |
| /* BCR - bus configuration */ |
| #define CONFIG_SYS_BCR 0x00000000 |
| |
| /* SIUMCR - siu module configuration */ |
| #define CONFIG_SYS_SIUMCR 0x4905c000 |
| |
| /* SYPCR - system protection control */ |
| #if defined(CONFIG_WATCHDOG) |
| #define CONFIG_SYS_SYPCR 0xffffff87 |
| #else |
| #define CONFIG_SYS_SYPCR 0xffffff83 |
| #endif |
| |
| /* TMCNTSC - time counter status and control */ |
| /* clear interrupts XXX jse */ |
| /*#define CONFIG_SYS_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR) */ |
| #define CONFIG_SYS_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|\ |
| TMCNTSC_TCF|TMCNTSC_TCE) |
| |
| /* PISCR - periodic interrupt status and control */ |
| /* clear interrupts XXX jse */ |
| /*#define CONFIG_SYS_PISCR (PISCR_PS) */ |
| #define CONFIG_SYS_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE) |
| |
| /* SCCR - system clock control */ |
| #define CONFIG_SYS_SCCR 0x000001a9 |
| |
| /* RCCR - risc controller configuration */ |
| #define CONFIG_SYS_RCCR 0 |
| |
| /* |
| * MEMORY MAP |
| * ---------- |
| * CS0 - FLASH 8MB/8Bit base=0xff800000 (boot: 0xfe000000, 8x mirrored) |
| * CS1 - SDRAM 32MB/64Bit base=0x00000000 |
| * CS2 - DSP/SL1 1MB/16Bit base=0xf0100000 |
| * CS3 - DSP/SL2 1MB/16Bit base=0xf0200000 |
| * CS4 - DSP/SL3 1MB/16Bit base=0xf0300000 |
| * CS5 - DSP/SL4 1MB/16Bit base=0xf0400000 |
| * CS7 - DPRAM 1KB/8Bit base=0xf0500000, size=32KB (32x mirrored) |
| * x - IMMR 384KB base=0xf0000000 |
| */ |
| /* XXX jse 100MHz TODO */ |
| #define CONFIG_SYS_BR0_PRELIM 0xff800801 |
| #define CONFIG_SYS_OR0_PRELIM 0xff801e44 |
| #define CONFIG_SYS_BR1_PRELIM 0x00000041 |
| #define CONFIG_SYS_OR1_PRELIM 0xfe002ec0 |
| #if 1 |
| #define CONFIG_SYS_BR2_PRELIM 0xf0101001 |
| #define CONFIG_SYS_OR2_PRELIM 0xfff00ef4 |
| #define CONFIG_SYS_BR3_PRELIM 0xf0201001 |
| #define CONFIG_SYS_OR3_PRELIM 0xfff00ef4 |
| #define CONFIG_SYS_BR4_PRELIM 0xf0301001 |
| #define CONFIG_SYS_OR4_PRELIM 0xfff00ef4 |
| #define CONFIG_SYS_BR5_PRELIM 0xf0401001 |
| #define CONFIG_SYS_OR5_PRELIM 0xfff00ef4 |
| #else |
| #define CONFIG_SYS_BR2_PRELIM 0xf0101081 |
| #define CONFIG_SYS_OR2_PRELIM 0xfff00104 |
| #define CONFIG_SYS_BR3_PRELIM 0xf0201081 |
| #define CONFIG_SYS_OR3_PRELIM 0xfff00104 |
| #define CONFIG_SYS_BR4_PRELIM 0xf0301081 |
| #define CONFIG_SYS_OR4_PRELIM 0xfff00104 |
| #define CONFIG_SYS_BR5_PRELIM 0xf0401081 |
| #define CONFIG_SYS_OR5_PRELIM 0xfff00104 |
| #endif |
| #define CONFIG_SYS_BR7_PRELIM 0xf0500881 |
| #define CONFIG_SYS_OR7_PRELIM 0xffff8104 |
| #define CONFIG_SYS_MPTPR 0x2700 |
| #define CONFIG_SYS_PSDMR 0x822a2452 /* optimal */ |
| /*#define CONFIG_SYS_PSDMR 0x822a48a3 */ /* relaxed */ |
| #define CONFIG_SYS_PSRT 0x1a |
| |
| /* "bad" address */ |
| #define CONFIG_SYS_RESET_ADDRESS 0x40000000 |
| |
| #endif /* __CONFIG_H */ |