| /* |
| * Copyright (C) 2006 Freescale Semiconductor, Inc. |
| * |
| * Dave Liu <daveliu@freescale.com> |
| * |
| * This program is free software; you can redistribute it and/or |
| * modify it under the terms of the GNU General Public License as |
| * published by the Free Software Foundation; either version 2 of |
| * the License, or (at your option) any later version. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 59 Temple Place, Suite 330, Boston, |
| * MA 02111-1307 USA |
| */ |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| /* |
| * High Level Configuration Options |
| */ |
| #define CONFIG_E300 1 /* E300 family */ |
| #define CONFIG_QE 1 /* Has QE */ |
| #define CONFIG_MPC83XX 1 /* MPC83XX family */ |
| #define CONFIG_MPC8360 1 /* MPC8360 CPU specific */ |
| #define CONFIG_MPC8360EMDS 1 /* MPC8360EMDS board specific */ |
| #undef CONFIG_PQ_MDS_PIB /* POWERQUICC MDS Platform IO Board */ |
| #undef CONFIG_PQ_MDS_PIB_ATM /* QOC3 ATM card */ |
| |
| /* |
| * System Clock Setup |
| */ |
| #ifdef CONFIG_PCISLAVE |
| #define CONFIG_83XX_PCICLK 66000000 /* in HZ */ |
| #else |
| #define CONFIG_83XX_CLKIN 66000000 /* in Hz */ |
| #endif |
| |
| #ifndef CONFIG_SYS_CLK_FREQ |
| #define CONFIG_SYS_CLK_FREQ 66000000 |
| #endif |
| |
| /* |
| * Hardware Reset Configuration Word |
| */ |
| #define CONFIG_SYS_HRCW_LOW (\ |
| HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ |
| HRCWL_DDR_TO_SCB_CLK_1X1 |\ |
| HRCWL_CSB_TO_CLKIN_4X1 |\ |
| HRCWL_VCO_1X2 |\ |
| HRCWL_CE_PLL_VCO_DIV_4 |\ |
| HRCWL_CE_PLL_DIV_1X1 |\ |
| HRCWL_CE_TO_PLL_1X6 |\ |
| HRCWL_CORE_TO_CSB_2X1) |
| |
| #ifdef CONFIG_PCISLAVE |
| #define CONFIG_SYS_HRCW_HIGH (\ |
| HRCWH_PCI_AGENT |\ |
| HRCWH_PCI1_ARBITER_DISABLE |\ |
| HRCWH_PCICKDRV_DISABLE |\ |
| HRCWH_CORE_ENABLE |\ |
| HRCWH_FROM_0XFFF00100 |\ |
| HRCWH_BOOTSEQ_DISABLE |\ |
| HRCWH_SW_WATCHDOG_DISABLE |\ |
| HRCWH_ROM_LOC_LOCAL_16BIT) |
| #else |
| #define CONFIG_SYS_HRCW_HIGH (\ |
| HRCWH_PCI_HOST |\ |
| HRCWH_PCI1_ARBITER_ENABLE |\ |
| HRCWH_PCICKDRV_ENABLE |\ |
| HRCWH_CORE_ENABLE |\ |
| HRCWH_FROM_0X00000100 |\ |
| HRCWH_BOOTSEQ_DISABLE |\ |
| HRCWH_SW_WATCHDOG_DISABLE |\ |
| HRCWH_ROM_LOC_LOCAL_16BIT) |
| #endif |
| |
| /* |
| * System IO Config |
| */ |
| #define CONFIG_SYS_SICRH 0x00000000 |
| #define CONFIG_SYS_SICRL 0x40000000 |
| |
| #define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */ |
| #define CONFIG_BOARD_EARLY_INIT_R |
| |
| /* |
| * IMMR new address |
| */ |
| #define CONFIG_SYS_IMMR 0xE0000000 |
| |
| /* |
| * DDR Setup |
| */ |
| #define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */ |
| #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE |
| #define CONFIG_SYS_SDRAM_BASE2 (CONFIG_SYS_SDRAM_BASE + 0x10000000) /* + 256M */ |
| #define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE |
| #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN | \ |
| DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05) |
| |
| #define CONFIG_SYS_83XX_DDR_USES_CS0 |
| |
| #define CONFIG_DDR_ECC /* support DDR ECC function */ |
| #define CONFIG_DDR_ECC_CMD /* Use DDR ECC user commands */ |
| |
| /* |
| * DDRCDR - DDR Control Driver Register |
| */ |
| #define CONFIG_SYS_DDRCDR_VALUE 0x80080001 |
| |
| #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ |
| #if defined(CONFIG_SPD_EEPROM) |
| /* |
| * Determine DDR configuration from I2C interface. |
| */ |
| #define SPD_EEPROM_ADDRESS 0x52 /* DDR SODIMM */ |
| #else |
| /* |
| * Manually set up DDR parameters |
| */ |
| #define CONFIG_SYS_DDR_SIZE 256 /* MB */ |
| #if defined(CONFIG_DDR_II) |
| #define CONFIG_SYS_DDRCDR 0x80080001 |
| #define CONFIG_SYS_DDR_CS0_BNDS 0x0000000f |
| #define CONFIG_SYS_DDR_CS0_CONFIG 0x80330102 |
| #define CONFIG_SYS_DDR_TIMING_0 0x00220802 |
| #define CONFIG_SYS_DDR_TIMING_1 0x38357322 |
| #define CONFIG_SYS_DDR_TIMING_2 0x2f9048c8 |
| #define CONFIG_SYS_DDR_TIMING_3 0x00000000 |
| #define CONFIG_SYS_DDR_CLK_CNTL 0x02000000 |
| #define CONFIG_SYS_DDR_MODE 0x47d00432 |
| #define CONFIG_SYS_DDR_MODE2 0x8000c000 |
| #define CONFIG_SYS_DDR_INTERVAL 0x03cf0080 |
| #define CONFIG_SYS_DDR_SDRAM_CFG 0x43000000 |
| #define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 |
| #else |
| #define CONFIG_SYS_DDR_CONFIG (CSCONFIG_EN | CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_9) |
| #define CONFIG_SYS_DDR_TIMING_1 0x37344321 /* tCL-tRCD-tRP-tRAS=2.5-3-3-7 */ |
| #define CONFIG_SYS_DDR_TIMING_2 0x00000800 /* may need tuning */ |
| #define CONFIG_SYS_DDR_CONTROL 0x42008000 /* Self refresh,2T timing */ |
| #define CONFIG_SYS_DDR_MODE 0x20000162 /* DLL,normal,seq,4/2.5 */ |
| #define CONFIG_SYS_DDR_INTERVAL 0x045b0100 /* page mode */ |
| #endif |
| #endif |
| |
| /* |
| * Memory test |
| */ |
| #undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */ |
| #define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest region */ |
| #define CONFIG_SYS_MEMTEST_END 0x00100000 |
| |
| /* |
| * The reserved memory |
| */ |
| |
| #define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */ |
| |
| #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) |
| #define CONFIG_SYS_RAMBOOT |
| #else |
| #undef CONFIG_SYS_RAMBOOT |
| #endif |
| |
| /* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */ |
| #define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ |
| #define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ |
| |
| /* |
| * Initial RAM Base Address Setup |
| */ |
| #define CONFIG_SYS_INIT_RAM_LOCK 1 |
| #define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ |
| #define CONFIG_SYS_INIT_RAM_END 0x1000 /* End of used area in RAM */ |
| #define CONFIG_SYS_GBL_DATA_SIZE 0x100 /* num bytes initial data */ |
| #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) |
| |
| /* |
| * Local Bus Configuration & Clock Setup |
| */ |
| #define CONFIG_SYS_LCRR (LCRR_DBYP | LCRR_CLKDIV_4) |
| #define CONFIG_SYS_LBC_LBCR 0x00000000 |
| |
| /* |
| * FLASH on the Local Bus |
| */ |
| #define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */ |
| #define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */ |
| #define CONFIG_SYS_FLASH_BASE 0xFE000000 /* FLASH base address */ |
| #define CONFIG_SYS_FLASH_SIZE 32 /* max FLASH size is 32M */ |
| #define CONFIG_SYS_FLASH_PROTECTION 1 /* Use h/w Flash protection. */ |
| #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ |
| |
| #define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE /* Window base at flash base */ |
| #define CONFIG_SYS_LBLAWAR0_PRELIM 0x80000018 /* 32MB window size */ |
| |
| #define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | /* Flash Base address */ \ |
| (2 << BR_PS_SHIFT) | /* 16 bit port size */ \ |
| BR_V) /* valid */ |
| #define CONFIG_SYS_OR0_PRELIM ((~(CONFIG_SYS_FLASH_SIZE - 1) << 20) | OR_UPM_XAM | \ |
| OR_GPCM_CSNT | OR_GPCM_ACS_DIV2 | OR_GPCM_XACS | OR_GPCM_SCY_15 | \ |
| OR_GPCM_TRLX | OR_GPCM_EHTR | OR_GPCM_EAD) |
| |
| #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ |
| #define CONFIG_SYS_MAX_FLASH_SECT 256 /* max sectors per device */ |
| |
| #undef CONFIG_SYS_FLASH_CHECKSUM |
| |
| /* |
| * BCSR on the Local Bus |
| */ |
| #define CONFIG_SYS_BCSR 0xF8000000 |
| #define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_BCSR /* Access window base at BCSR base */ |
| #define CONFIG_SYS_LBLAWAR1_PRELIM 0x8000000F /* Access window size 64K */ |
| |
| #define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_BCSR|0x00000801) /* Port size=8bit, MSEL=GPCM */ |
| #define CONFIG_SYS_OR1_PRELIM 0xFFFFE9f7 /* length 32K */ |
| |
| /* |
| * SDRAM on the Local Bus |
| */ |
| #define CONFIG_SYS_LBC_SDRAM_BASE 0xF0000000 /* SDRAM base address */ |
| #define CONFIG_SYS_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */ |
| |
| #define CONFIG_SYS_LB_SDRAM /* if board has SRDAM on local bus */ |
| |
| #ifdef CONFIG_SYS_LB_SDRAM |
| #define CONFIG_SYS_LBLAWBAR2 0 |
| #define CONFIG_SYS_LBLAWAR2 0x80000019 /* 64MB */ |
| |
| /*local bus BR2, OR2 definition for SDRAM if soldered on the EPB board */ |
| /* |
| * Base Register 2 and Option Register 2 configure SDRAM. |
| * |
| * For BR2, need: |
| * Base address = BR[0:16] = dynamic |
| * port size = 32-bits = BR2[19:20] = 11 |
| * no parity checking = BR2[21:22] = 00 |
| * SDRAM for MSEL = BR2[24:26] = 011 |
| * Valid = BR[31] = 1 |
| * |
| * 0 4 8 12 16 20 24 28 |
| * xxxx xxxx xxxx xxxx x001 1000 0110 0001 = 00001861 |
| */ |
| |
| #define CONFIG_SYS_BR2 0x00001861 /*Port size=32bit, MSEL=SDRAM */ |
| |
| /* |
| * The SDRAM size in MB, CONFIG_SYS_LBC_SDRAM_SIZE, is 64. |
| * |
| * For OR2, need: |
| * 64MB mask for AM, OR2[0:7] = 1111 1100 |
| * XAM, OR2[17:18] = 11 |
| * 9 columns OR2[19-21] = 010 |
| * 13 rows OR2[23-25] = 100 |
| * EAD set for extra time OR[31] = 1 |
| * |
| * 0 4 8 12 16 20 24 28 |
| * 1111 1100 0000 0000 0110 1001 0000 0001 = fc006901 |
| */ |
| |
| #define CONFIG_SYS_OR2 0xfc006901 |
| |
| #define CONFIG_SYS_LBC_LSRT 0x32000000 /* LB sdram refresh timer, about 6us */ |
| #define CONFIG_SYS_LBC_MRTPR 0x20000000 /* LB refresh timer prescal, 266MHz/32 */ |
| |
| /* |
| * LSDMR masks |
| */ |
| #define CONFIG_SYS_LBC_LSDMR_OP_NORMAL (0 << (31 - 4)) |
| #define CONFIG_SYS_LBC_LSDMR_OP_ARFRSH (1 << (31 - 4)) |
| #define CONFIG_SYS_LBC_LSDMR_OP_SRFRSH (2 << (31 - 4)) |
| #define CONFIG_SYS_LBC_LSDMR_OP_MRW (3 << (31 - 4)) |
| #define CONFIG_SYS_LBC_LSDMR_OP_PRECH (4 << (31 - 4)) |
| #define CONFIG_SYS_LBC_LSDMR_OP_PCHALL (5 << (31 - 4)) |
| #define CONFIG_SYS_LBC_LSDMR_OP_ACTBNK (6 << (31 - 4)) |
| #define CONFIG_SYS_LBC_LSDMR_OP_RWINV (7 << (31 - 4)) |
| |
| #define CONFIG_SYS_LBC_LSDMR_COMMON 0x0063b723 |
| |
| /* |
| * SDRAM Controller configuration sequence. |
| */ |
| #define CONFIG_SYS_LBC_LSDMR_1 ( CONFIG_SYS_LBC_LSDMR_COMMON \ |
| | CONFIG_SYS_LBC_LSDMR_OP_PCHALL) |
| #define CONFIG_SYS_LBC_LSDMR_2 ( CONFIG_SYS_LBC_LSDMR_COMMON \ |
| | CONFIG_SYS_LBC_LSDMR_OP_ARFRSH) |
| #define CONFIG_SYS_LBC_LSDMR_3 ( CONFIG_SYS_LBC_LSDMR_COMMON \ |
| | CONFIG_SYS_LBC_LSDMR_OP_ARFRSH) |
| #define CONFIG_SYS_LBC_LSDMR_4 ( CONFIG_SYS_LBC_LSDMR_COMMON \ |
| | CONFIG_SYS_LBC_LSDMR_OP_MRW) |
| #define CONFIG_SYS_LBC_LSDMR_5 ( CONFIG_SYS_LBC_LSDMR_COMMON \ |
| | CONFIG_SYS_LBC_LSDMR_OP_NORMAL) |
| |
| #endif |
| |
| /* |
| * Windows to access PIB via local bus |
| */ |
| #define CONFIG_SYS_LBLAWBAR3_PRELIM 0xf8010000 /* windows base 0xf8010000 */ |
| #define CONFIG_SYS_LBLAWAR3_PRELIM 0x8000000e /* windows size 32KB */ |
| |
| /* |
| * CS4 on Local Bus, to PIB |
| */ |
| #define CONFIG_SYS_BR4_PRELIM 0xf8010801 /* CS4 base address at 0xf8010000 */ |
| #define CONFIG_SYS_OR4_PRELIM 0xffffe9f7 /* size 32KB, port size 8bit, GPCM */ |
| |
| /* |
| * CS5 on Local Bus, to PIB |
| */ |
| #define CONFIG_SYS_BR5_PRELIM 0xf8008801 /* CS5 base address at 0xf8008000 */ |
| #define CONFIG_SYS_OR5_PRELIM 0xffffe9f7 /* size 32KB, port size 8bit, GPCM */ |
| |
| /* |
| * Serial Port |
| */ |
| #define CONFIG_CONS_INDEX 1 |
| #undef CONFIG_SERIAL_SOFTWARE_FIFO |
| #define CONFIG_SYS_NS16550 |
| #define CONFIG_SYS_NS16550_SERIAL |
| #define CONFIG_SYS_NS16550_REG_SIZE 1 |
| #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) |
| |
| #define CONFIG_SYS_BAUDRATE_TABLE \ |
| {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} |
| |
| #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500) |
| #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600) |
| |
| #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ |
| /* Use the HUSH parser */ |
| #define CONFIG_SYS_HUSH_PARSER |
| #ifdef CONFIG_SYS_HUSH_PARSER |
| #define CONFIG_SYS_PROMPT_HUSH_PS2 "> " |
| #endif |
| |
| /* pass open firmware flat tree */ |
| #define CONFIG_OF_LIBFDT 1 |
| #define CONFIG_OF_BOARD_SETUP 1 |
| #define CONFIG_OF_STDOUT_VIA_ALIAS 1 |
| |
| /* I2C */ |
| #define CONFIG_HARD_I2C /* I2C with hardware support */ |
| #undef CONFIG_SOFT_I2C /* I2C bit-banged */ |
| #define CONFIG_FSL_I2C |
| #define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ |
| #define CONFIG_SYS_I2C_SLAVE 0x7F |
| #define CONFIG_SYS_I2C_NOPROBES {0x52} /* Don't probe these addrs */ |
| #define CONFIG_SYS_I2C_OFFSET 0x3000 |
| #define CONFIG_SYS_I2C2_OFFSET 0x3100 |
| |
| /* |
| * Config on-board RTC |
| */ |
| #define CONFIG_RTC_DS1374 /* use ds1374 rtc via i2c */ |
| #define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */ |
| |
| /* |
| * General PCI |
| * Addresses are mapped 1-1. |
| */ |
| #define CONFIG_SYS_PCI_MEM_BASE 0x80000000 |
| #define CONFIG_SYS_PCI_MEM_PHYS CONFIG_SYS_PCI_MEM_BASE |
| #define CONFIG_SYS_PCI_MEM_SIZE 0x10000000 /* 256M */ |
| #define CONFIG_SYS_PCI_MMIO_BASE 0x90000000 |
| #define CONFIG_SYS_PCI_MMIO_PHYS CONFIG_SYS_PCI_MMIO_BASE |
| #define CONFIG_SYS_PCI_MMIO_SIZE 0x10000000 /* 256M */ |
| #define CONFIG_SYS_PCI_IO_BASE 0x00000000 |
| #define CONFIG_SYS_PCI_IO_PHYS 0xE0300000 |
| #define CONFIG_SYS_PCI_IO_SIZE 0x100000 /* 1M */ |
| |
| #define CONFIG_SYS_PCI_SLV_MEM_LOCAL CONFIG_SYS_SDRAM_BASE |
| #define CONFIG_SYS_PCI_SLV_MEM_BUS 0x00000000 |
| #define CONFIG_SYS_PCI_SLV_MEM_SIZE 0x80000000 |
| |
| |
| #ifdef CONFIG_PCI |
| |
| #define CONFIG_NET_MULTI |
| #define CONFIG_PCI_PNP /* do pci plug-and-play */ |
| |
| #undef CONFIG_EEPRO100 |
| #undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ |
| #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ |
| |
| #endif /* CONFIG_PCI */ |
| |
| |
| #ifndef CONFIG_NET_MULTI |
| #define CONFIG_NET_MULTI 1 |
| #endif |
| |
| /* |
| * QE UEC ethernet configuration |
| */ |
| #define CONFIG_UEC_ETH |
| #define CONFIG_ETHPRIME "FSL UEC0" |
| #define CONFIG_PHY_MODE_NEED_CHANGE |
| |
| #define CONFIG_UEC_ETH1 /* GETH1 */ |
| |
| #ifdef CONFIG_UEC_ETH1 |
| #define CONFIG_SYS_UEC1_UCC_NUM 0 /* UCC1 */ |
| #define CONFIG_SYS_UEC1_RX_CLK QE_CLK_NONE |
| #define CONFIG_SYS_UEC1_TX_CLK QE_CLK9 |
| #define CONFIG_SYS_UEC1_ETH_TYPE GIGA_ETH |
| #define CONFIG_SYS_UEC1_PHY_ADDR 0 |
| #define CONFIG_SYS_UEC1_INTERFACE_MODE ENET_1000_GMII |
| #endif |
| |
| #define CONFIG_UEC_ETH2 /* GETH2 */ |
| |
| #ifdef CONFIG_UEC_ETH2 |
| #define CONFIG_SYS_UEC2_UCC_NUM 1 /* UCC2 */ |
| #define CONFIG_SYS_UEC2_RX_CLK QE_CLK_NONE |
| #define CONFIG_SYS_UEC2_TX_CLK QE_CLK4 |
| #define CONFIG_SYS_UEC2_ETH_TYPE GIGA_ETH |
| #define CONFIG_SYS_UEC2_PHY_ADDR 1 |
| #define CONFIG_SYS_UEC2_INTERFACE_MODE ENET_1000_GMII |
| #endif |
| |
| /* |
| * Environment |
| */ |
| |
| #ifndef CONFIG_SYS_RAMBOOT |
| #define CONFIG_ENV_IS_IN_FLASH 1 |
| #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) |
| #define CONFIG_ENV_SECT_SIZE 0x20000 |
| #define CONFIG_ENV_SIZE 0x2000 |
| #else |
| #define CONFIG_SYS_NO_FLASH 1 /* Flash is not usable now */ |
| #define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ |
| #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) |
| #define CONFIG_ENV_SIZE 0x2000 |
| #endif |
| |
| #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ |
| #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ |
| |
| /* |
| * BOOTP options |
| */ |
| #define CONFIG_BOOTP_BOOTFILESIZE |
| #define CONFIG_BOOTP_BOOTPATH |
| #define CONFIG_BOOTP_GATEWAY |
| #define CONFIG_BOOTP_HOSTNAME |
| |
| |
| /* |
| * Command line configuration. |
| */ |
| #include <config_cmd_default.h> |
| |
| #define CONFIG_CMD_PING |
| #define CONFIG_CMD_I2C |
| #define CONFIG_CMD_ASKENV |
| #define CONFIG_CMD_SDRAM |
| |
| #if defined(CONFIG_PCI) |
| #define CONFIG_CMD_PCI |
| #endif |
| |
| #if defined(CONFIG_SYS_RAMBOOT) |
| #undef CONFIG_CMD_SAVEENV |
| #undef CONFIG_CMD_LOADS |
| #endif |
| |
| |
| #undef CONFIG_WATCHDOG /* watchdog disabled */ |
| |
| /* |
| * Miscellaneous configurable options |
| */ |
| #define CONFIG_SYS_LONGHELP /* undef to save memory */ |
| #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ |
| #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ |
| |
| #if defined(CONFIG_CMD_KGDB) |
| #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ |
| #else |
| #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ |
| #endif |
| |
| #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ |
| #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ |
| #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ |
| #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ |
| |
| /* |
| * For booting Linux, the board info and command line data |
| * have to be in the first 8 MB of memory, since this is |
| * the maximum mapped by the Linux kernel during initialization. |
| */ |
| #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ |
| |
| /* |
| * Core HID Setup |
| */ |
| #define CONFIG_SYS_HID0_INIT 0x000000000 |
| #define CONFIG_SYS_HID0_FINAL HID0_ENABLE_MACHINE_CHECK |
| #define CONFIG_SYS_HID2 HID2_HBE |
| |
| /* |
| * MMU Setup |
| */ |
| |
| #define CONFIG_HIGH_BATS 1 /* High BATs supported */ |
| |
| /* DDR/LBC SDRAM: cacheable */ |
| #define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) |
| #define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) |
| #define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L |
| #define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U |
| |
| /* IMMRBAR & PCI IO: cache-inhibit and guarded */ |
| #define CONFIG_SYS_IBAT1L (CONFIG_SYS_IMMR | BATL_PP_10 | \ |
| BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) |
| #define CONFIG_SYS_IBAT1U (CONFIG_SYS_IMMR | BATU_BL_4M | BATU_VS | BATU_VP) |
| #define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L |
| #define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U |
| |
| /* BCSR: cache-inhibit and guarded */ |
| #define CONFIG_SYS_IBAT2L (CONFIG_SYS_BCSR | BATL_PP_10 | \ |
| BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) |
| #define CONFIG_SYS_IBAT2U (CONFIG_SYS_BCSR | BATU_BL_128K | BATU_VS | BATU_VP) |
| #define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L |
| #define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U |
| |
| /* FLASH: icache cacheable, but dcache-inhibit and guarded */ |
| #define CONFIG_SYS_IBAT3L (CONFIG_SYS_FLASH_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) |
| #define CONFIG_SYS_IBAT3U (CONFIG_SYS_FLASH_BASE | BATU_BL_32M | BATU_VS | BATU_VP) |
| #define CONFIG_SYS_DBAT3L (CONFIG_SYS_FLASH_BASE | BATL_PP_10 | \ |
| BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) |
| #define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U |
| |
| /* DDR/LBC SDRAM next 256M: cacheable */ |
| #define CONFIG_SYS_IBAT4L (CONFIG_SYS_SDRAM_BASE2 | BATL_PP_10 | BATL_MEMCOHERENCE) |
| #define CONFIG_SYS_IBAT4U (CONFIG_SYS_SDRAM_BASE2 | BATU_BL_256M | BATU_VS | BATU_VP) |
| #define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L |
| #define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U |
| |
| /* Stack in dcache: cacheable, no memory coherence */ |
| #define CONFIG_SYS_IBAT5L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_10) |
| #define CONFIG_SYS_IBAT5U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP) |
| #define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L |
| #define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U |
| |
| #ifdef CONFIG_PCI |
| /* PCI MEM space: cacheable */ |
| #define CONFIG_SYS_IBAT6L (CONFIG_SYS_PCI_MEM_PHYS | BATL_PP_10 | BATL_MEMCOHERENCE) |
| #define CONFIG_SYS_IBAT6U (CONFIG_SYS_PCI_MEM_PHYS | BATU_BL_256M | BATU_VS | BATU_VP) |
| #define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L |
| #define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U |
| /* PCI MMIO space: cache-inhibit and guarded */ |
| #define CONFIG_SYS_IBAT7L (CONFIG_SYS_PCI_MMIO_PHYS | BATL_PP_10 | \ |
| BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) |
| #define CONFIG_SYS_IBAT7U (CONFIG_SYS_PCI_MMIO_PHYS | BATU_BL_256M | BATU_VS | BATU_VP) |
| #define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L |
| #define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U |
| #else |
| #define CONFIG_SYS_IBAT6L (0) |
| #define CONFIG_SYS_IBAT6U (0) |
| #define CONFIG_SYS_IBAT7L (0) |
| #define CONFIG_SYS_IBAT7U (0) |
| #define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L |
| #define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U |
| #define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L |
| #define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U |
| #endif |
| |
| /* |
| * Internal Definitions |
| * |
| * Boot Flags |
| */ |
| #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ |
| #define BOOTFLAG_WARM 0x02 /* Software reboot */ |
| |
| #if defined(CONFIG_CMD_KGDB) |
| #define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */ |
| #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ |
| #endif |
| |
| /* |
| * Environment Configuration |
| */ |
| |
| #define CONFIG_ENV_OVERWRITE |
| |
| #if defined(CONFIG_UEC_ETH) |
| #define CONFIG_HAS_ETH0 |
| #define CONFIG_ETHADDR 00:04:9f:ef:01:01 |
| #define CONFIG_HAS_ETH1 |
| #define CONFIG_ETH1ADDR 00:04:9f:ef:01:02 |
| #endif |
| |
| #define CONFIG_BAUDRATE 115200 |
| |
| #define CONFIG_LOADADDR 500000 /* default location for tftp and bootm */ |
| |
| #define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */ |
| #undef CONFIG_BOOTARGS /* the boot command will set bootargs */ |
| |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| "netdev=eth0\0" \ |
| "consoledev=ttyS0\0" \ |
| "ramdiskaddr=1000000\0" \ |
| "ramdiskfile=ramfs.83xx\0" \ |
| "fdtaddr=400000\0" \ |
| "fdtfile=mpc836x_mds.dtb\0" \ |
| "" |
| |
| #define CONFIG_NFSBOOTCOMMAND \ |
| "setenv bootargs root=/dev/nfs rw " \ |
| "nfsroot=$serverip:$rootpath " \ |
| "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ |
| "console=$consoledev,$baudrate $othbootargs;" \ |
| "tftp $loadaddr $bootfile;" \ |
| "tftp $fdtaddr $fdtfile;" \ |
| "bootm $loadaddr - $fdtaddr" |
| |
| #define CONFIG_RAMBOOTCOMMAND \ |
| "setenv bootargs root=/dev/ram rw " \ |
| "console=$consoledev,$baudrate $othbootargs;" \ |
| "tftp $ramdiskaddr $ramdiskfile;" \ |
| "tftp $loadaddr $bootfile;" \ |
| "tftp $fdtaddr $fdtfile;" \ |
| "bootm $loadaddr $ramdiskaddr $fdtaddr" |
| |
| |
| #define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND |
| |
| #endif /* __CONFIG_H */ |