| /* |
| * Copyright 2008 Extreme Engineering Solutions, Inc. |
| * Copyright 2008 Freescale Semiconductor, Inc. |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| #include <common.h> |
| #include <i2c.h> |
| |
| #include <fsl_ddr_sdram.h> |
| #include <fsl_ddr_dimm_params.h> |
| |
| void get_spd(ddr2_spd_eeprom_t *spd, u8 i2c_address) |
| { |
| i2c_read(i2c_address, SPD_EEPROM_OFFSET, 2, (uchar *)spd, |
| sizeof(ddr2_spd_eeprom_t)); |
| } |
| |
| /* |
| * There are four board-specific SDRAM timing parameters which must be |
| * calculated based on the particular PCB artwork. These are: |
| * 1.) CPO (Read Capture Delay) |
| * - TIMING_CFG_2 register |
| * Source: Calculation based on board trace lengths and |
| * chip-specific internal delays. |
| * 2.) WR_DATA_DELAY (Write Command to Data Strobe Delay) |
| * - TIMING_CFG_2 register |
| * Source: Calculation based on board trace lengths. |
| * Unless clock and DQ lanes are very different |
| * lengths (>2"), this should be set to the nominal value |
| * of 1/2 clock delay. |
| * 3.) CLK_ADJUST (Clock and Addr/Cmd alignment control) |
| * - DDR_SDRAM_CLK_CNTL register |
| * Source: Signal Integrity Simulations |
| * 4.) 2T Timing on Addr/Ctl |
| * - TIMING_CFG_2 register |
| * Source: Signal Integrity Simulations |
| * Usually only needed with heavy load/very high speed (>DDR2-800) |
| * |
| * ====== XPedite5370 DDR2-600 read delay calculations ====== |
| * |
| * See Freescale's App Note AN2583 as refrence. This document also |
| * contains the chip-specific delays for 8548E, 8572, etc. |
| * |
| * For MPC8572E |
| * Minimum chip delay (Ch 0): 1.372ns |
| * Maximum chip delay (Ch 0): 2.914ns |
| * Minimum chip delay (Ch 1): 1.220ns |
| * Maximum chip delay (Ch 1): 2.595ns |
| * |
| * CLK adjust = 5 (from simulations) = 5/8* 3.33ns = 2080ps |
| * |
| * Minimum delay calc (Ch 0): |
| * clock prop - dram skew + min dqs prop delay + clk_adjust + min chip dly |
| * 2.3" * 180 - 400ps + 1.9" * 180 + 2080ps + 1372ps |
| * = 3808ps |
| * = 3.808ns |
| * |
| * Maximum delay calc (Ch 0): |
| * clock prop + dram skew + max dqs prop delay + clk_adjust + max chip dly |
| * 2.3" * 180 + 400ps + 2.4" * 180 + 2080ps + 2914ps |
| * = 6240ps |
| * = 6.240ns |
| * |
| * Minimum delay calc (Ch 1): |
| * clock prop - dram skew + min dqs prop delay + clk_adjust + min chip dly |
| * 1.46" * 180- 400ps + 0.7" * 180 + 2080ps + 1220ps |
| * = 3288ps |
| * = 3.288ns |
| * |
| * Maximum delay calc (Ch 1): |
| * clock prop + dram skew + max dqs prop delay + clk_adjust + min chip dly |
| * 1.46" * 180+ 400ps + 1.1" * 180 + 2080ps + 2595ps |
| * = 5536ps |
| * = 5.536ns |
| * |
| * Ch.0: 3.808ns to 6.240ns additional delay needed (pick 5ns as target) |
| * This is 1.5 clock cycles, pick CPO = READ_LAT + 3/2 (0x8) |
| * Ch.1: 3.288ns to 5.536ns additional delay needed (pick 4.4ns as target) |
| * This is 1.32 clock cycles, pick CPO = READ_LAT + 5/4 (0x7) |
| * |
| * |
| * ====== XPedite5370 DDR2-800 read delay calculations ====== |
| * |
| * See Freescale's App Note AN2583 as refrence. This document also |
| * contains the chip-specific delays for 8548E, 8572, etc. |
| * |
| * For MPC8572E |
| * Minimum chip delay (Ch 0): 1.372ns |
| * Maximum chip delay (Ch 0): 2.914ns |
| * Minimum chip delay (Ch 1): 1.220ns |
| * Maximum chip delay (Ch 1): 2.595ns |
| * |
| * CLK adjust = 5 (from simulations) = 5/8* 2.5ns = 1563ps |
| * |
| * Minimum delay calc (Ch 0): |
| * clock prop - dram skew + min dqs prop delay + clk_adjust + min chip dly |
| * 2.3" * 180 - 350ps + 1.9" * 180 + 1563ps + 1372ps |
| * = 3341ps |
| * = 3.341ns |
| * |
| * Maximum delay calc (Ch 0): |
| * clock prop + dram skew + max dqs prop delay + clk_adjust + max chip dly |
| * 2.3" * 180 + 350ps + 2.4" * 180 + 1563ps + 2914ps |
| * = 5673ps |
| * = 5.673ns |
| * |
| * Minimum delay calc (Ch 1): |
| * clock prop - dram skew + min dqs prop delay + clk_adjust + min chip dly |
| * 1.46" * 180- 350ps + 0.7" * 180 + 1563ps + 1220ps |
| * = 2822ps |
| * = 2.822ns |
| * |
| * Maximum delay calc (Ch 1): |
| * clock prop + dram skew + max dqs prop delay + clk_adjust + min chip dly |
| * 1.46" * 180+ 350ps + 1.1" * 180 + 1563ps + 2595ps |
| * = 4968ps |
| * = 4.968ns |
| * |
| * Ch.0: 3.341ns to 5.673ns additional delay needed (pick 4.5ns as target) |
| * This is 1.8 clock cycles, pick CPO = READ_LAT + 7/4 (0x9) |
| * Ch.1: 2.822ns to 4.968ns additional delay needed (pick 3.9ns as target) |
| * This is 1.56 clock cycles, pick CPO = READ_LAT + 3/2 (0x8) |
| * |
| * Write latency (WR_DATA_DELAY) is calculated by doing the following: |
| * |
| * The DDR SDRAM specification requires DQS be received no sooner than |
| * 75% of an SDRAM clock period—and no later than 125% of a clock |
| * period—from the capturing clock edge of the command/address at the |
| * SDRAM. |
| * |
| * Based on the above tracelengths, the following are calculated: |
| * Ch. 0 8572 to DRAM propagation (DQ lanes) : 1.9" * 180 = 0.342ns |
| * Ch. 0 8572 to DRAM propagation (CLKs) : 2.3" * 180 = 0.414ns |
| * Ch. 1 8572 to DRAM propagation (DQ lanes) : 0.7" * 180 = 0.126ns |
| * Ch. 1 8572 to DRAM propagation (CLKs ) : 1.47" * 180 = 0.264ns |
| * |
| * Difference in arrival time CLK vs. DQS: |
| * Ch. 0 0.072ns |
| * Ch. 1 0.138ns |
| * |
| * Both of these values are much less than 25% of the clock |
| * period at DDR2-600 or DDR2-800, so no additional delay is needed over |
| * the 1/2 cycle which normally aligns the first DQS transition |
| * exactly WL (CAS latency minus one cycle) after the CAS strobe. |
| * See Figure 9-53 in MPC8572E manual: "1/2 delay" in Freescale's |
| * terminology corresponds to exactly one clock period delay after |
| * the CAS strobe. (due to the fact that the "delay" is referenced |
| * from the *falling* edge of the CLK, just after the rising edge |
| * which the CAS strobe is latched on. |
| */ |
| |
| typedef struct board_memctl_options { |
| uint16_t datarate_mhz_low; |
| uint16_t datarate_mhz_high; |
| uint8_t clk_adjust; |
| uint8_t cpo_override; |
| uint8_t write_data_delay; |
| } board_memctl_options_t; |
| |
| static struct board_memctl_options bopts_ctrl[][2] = { |
| { |
| /* Controller 0 */ |
| { |
| /* DDR2 600/667 */ |
| .datarate_mhz_low = 500, |
| .datarate_mhz_high = 750, |
| .clk_adjust = 5, |
| .cpo_override = 8, |
| .write_data_delay = 2, |
| }, |
| { |
| /* DDR2 800 */ |
| .datarate_mhz_low = 750, |
| .datarate_mhz_high = 850, |
| .clk_adjust = 5, |
| .cpo_override = 9, |
| .write_data_delay = 2, |
| }, |
| }, |
| { |
| /* Controller 1 */ |
| { |
| /* DDR2 600/667 */ |
| .datarate_mhz_low = 500, |
| .datarate_mhz_high = 750, |
| .clk_adjust = 5, |
| .cpo_override = 7, |
| .write_data_delay = 2, |
| }, |
| { |
| /* DDR2 800 */ |
| .datarate_mhz_low = 750, |
| .datarate_mhz_high = 850, |
| .clk_adjust = 5, |
| .cpo_override = 8, |
| .write_data_delay = 2, |
| }, |
| }, |
| }; |
| |
| void fsl_ddr_board_options(memctl_options_t *popts, |
| dimm_params_t *pdimm, |
| unsigned int ctrl_num) |
| { |
| struct board_memctl_options *bopts = bopts_ctrl[ctrl_num]; |
| sys_info_t sysinfo; |
| int i; |
| unsigned int datarate; |
| |
| get_sys_info(&sysinfo); |
| datarate = sysinfo.freq_ddrbus / 1000 / 1000; |
| |
| for (i = 0; i < ARRAY_SIZE(bopts_ctrl[ctrl_num]); i++) { |
| if ((bopts[i].datarate_mhz_low <= datarate) && |
| (bopts[i].datarate_mhz_high >= datarate)) { |
| debug("controller %d:\n", ctrl_num); |
| debug(" clk_adjust = %d\n", bopts[i].clk_adjust); |
| debug(" cpo = %d\n", bopts[i].cpo_override); |
| debug(" write_data_delay = %d\n", |
| bopts[i].write_data_delay); |
| popts->clk_adjust = bopts[i].clk_adjust; |
| popts->cpo_override = bopts[i].cpo_override; |
| popts->write_data_delay = bopts[i].write_data_delay; |
| } |
| } |
| |
| /* |
| * Factors to consider for half-strength driver enable: |
| * - number of DIMMs installed |
| */ |
| popts->half_strength_driver_enable = 0; |
| } |