| /* |
| * board/renesas/alt/alt.c |
| * |
| * Copyright (C) 2014 Renesas Electronics Corporation |
| * |
| * SPDX-License-Identifier: GPL-2.0 |
| */ |
| |
| #include <common.h> |
| #include <malloc.h> |
| #include <asm/processor.h> |
| #include <asm/mach-types.h> |
| #include <asm/io.h> |
| #include <asm/errno.h> |
| #include <asm/arch/sys_proto.h> |
| #include <asm/gpio.h> |
| #include <asm/arch/rmobile.h> |
| #include <netdev.h> |
| #include <miiphy.h> |
| #include <i2c.h> |
| #include <div64.h> |
| #include "qos.h" |
| |
| DECLARE_GLOBAL_DATA_PTR; |
| |
| #define CLK2MHZ(clk) (clk / 1000 / 1000) |
| void s_init(void) |
| { |
| struct rcar_rwdt *rwdt = (struct rcar_rwdt *)RWDT_BASE; |
| struct rcar_swdt *swdt = (struct rcar_swdt *)SWDT_BASE; |
| |
| /* Watchdog init */ |
| writel(0xA5A5A500, &rwdt->rwtcsra); |
| writel(0xA5A5A500, &swdt->swtcsra); |
| |
| /* QoS */ |
| qos_init(); |
| } |
| |
| #define MSTPSR1 0xE6150038 |
| #define SMSTPCR1 0xE6150134 |
| #define TMU0_MSTP125 (1 << 25) |
| |
| #define MSTPSR7 0xE61501C4 |
| #define SMSTPCR7 0xE615014C |
| #define SCIF0_MSTP719 (1 << 19) |
| |
| #define MSTPSR8 0xE61509A0 |
| #define SMSTPCR8 0xE6150990 |
| #define ETHER_MSTP813 (1 << 13) |
| |
| #define mstp_setbits(type, addr, saddr, set) \ |
| out_##type((saddr), in_##type(addr) | (set)) |
| #define mstp_clrbits(type, addr, saddr, clear) \ |
| out_##type((saddr), in_##type(addr) & ~(clear)) |
| #define mstp_setbits_le32(addr, saddr, set) \ |
| mstp_setbits(le32, addr, saddr, set) |
| #define mstp_clrbits_le32(addr, saddr, clear) \ |
| mstp_clrbits(le32, addr, saddr, clear) |
| |
| int board_early_init_f(void) |
| { |
| /* TMU */ |
| mstp_clrbits_le32(MSTPSR1, SMSTPCR1, TMU0_MSTP125); |
| |
| /* SCIF0 */ |
| mstp_clrbits_le32(MSTPSR7, SMSTPCR7, SCIF0_MSTP719); |
| |
| /* ETHER */ |
| mstp_clrbits_le32(MSTPSR8, SMSTPCR8, ETHER_MSTP813); |
| |
| return 0; |
| } |
| |
| void arch_preboot_os(void) |
| { |
| /* Disable TMU0 */ |
| mstp_setbits_le32(MSTPSR1, SMSTPCR1, TMU0_MSTP125); |
| } |
| |
| int board_init(void) |
| { |
| /* adress of boot parameters */ |
| gd->bd->bi_boot_params = ALT_SDRAM_BASE + 0x100; |
| |
| /* Init PFC controller */ |
| r8a7794_pinmux_init(); |
| |
| /* Ether Enable */ |
| gpio_request(GPIO_FN_ETH_CRS_DV, NULL); |
| gpio_request(GPIO_FN_ETH_RX_ER, NULL); |
| gpio_request(GPIO_FN_ETH_RXD0, NULL); |
| gpio_request(GPIO_FN_ETH_RXD1, NULL); |
| gpio_request(GPIO_FN_ETH_LINK, NULL); |
| gpio_request(GPIO_FN_ETH_REFCLK, NULL); |
| gpio_request(GPIO_FN_ETH_MDIO, NULL); |
| gpio_request(GPIO_FN_ETH_TXD1, NULL); |
| gpio_request(GPIO_FN_ETH_TX_EN, NULL); |
| gpio_request(GPIO_FN_ETH_MAGIC, NULL); |
| gpio_request(GPIO_FN_ETH_TXD0, NULL); |
| gpio_request(GPIO_FN_ETH_MDC, NULL); |
| gpio_request(GPIO_FN_IRQ8, NULL); |
| |
| /* PHY reset */ |
| gpio_request(GPIO_GP_1_24, NULL); |
| gpio_direction_output(GPIO_GP_1_24, 0); |
| mdelay(20); |
| gpio_set_value(GPIO_GP_1_24, 1); |
| udelay(1); |
| |
| return 0; |
| } |
| |
| #define CXR24 0xEE7003C0 /* MAC address high register */ |
| #define CXR25 0xEE7003C8 /* MAC address low register */ |
| int board_eth_init(bd_t *bis) |
| { |
| #ifdef CONFIG_SH_ETHER |
| int ret = -ENODEV; |
| u32 val; |
| unsigned char enetaddr[6]; |
| |
| ret = sh_eth_initialize(bis); |
| if (!eth_getenv_enetaddr("ethaddr", enetaddr)) |
| return ret; |
| |
| /* Set Mac address */ |
| val = enetaddr[0] << 24 | enetaddr[1] << 16 | |
| enetaddr[2] << 8 | enetaddr[3]; |
| writel(val, CXR24); |
| |
| val = enetaddr[4] << 8 | enetaddr[5]; |
| writel(val, CXR25); |
| |
| return ret; |
| #else |
| return 0; |
| #endif |
| } |
| |
| int dram_init(void) |
| { |
| gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE; |
| gd->ram_size = CONFIG_SYS_SDRAM_SIZE; |
| |
| return 0; |
| } |
| |
| const struct rmobile_sysinfo sysinfo = { |
| CONFIG_RMOBILE_BOARD_STRING |
| }; |
| |
| void dram_init_banksize(void) |
| { |
| gd->bd->bi_dram[0].start = ALT_SDRAM_BASE; |
| gd->bd->bi_dram[0].size = ALT_SDRAM_SIZE; |
| } |
| |
| int board_late_init(void) |
| { |
| return 0; |
| } |
| |
| void reset_cpu(ulong addr) |
| { |
| u8 val; |
| |
| i2c_set_bus_num(1); /* PowerIC connected to ch3 */ |
| i2c_init(400000, 0); |
| i2c_read(CONFIG_SYS_I2C_POWERIC_ADDR, 0x13, 1, &val, 1); |
| val |= 0x02; |
| i2c_write(CONFIG_SYS_I2C_POWERIC_ADDR, 0x13, 1, &val, 1); |
| } |