| /* |
| * Copyright 2007 Wind River Systems <www.windriver.com> |
| * Copyright 2007 Embedded Specialties, Inc. |
| * Joe Hamman <joe.hamman@embeddedspecialties.com> |
| * |
| * Copyright 2006 Freescale Semiconductor. |
| * |
| * Srikanth Srinivasan (srikanth.srinivasan@freescale.com) |
| * |
| * See file CREDITS for list of people who contributed to this |
| * project. |
| * |
| * This program is free software; you can redistribute it and/or |
| * modify it under the terms of the GNU General Public License as |
| * published by the Free Software Foundation; either version 2 of |
| * the License, or (at your option) any later version. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 59 Temple Place, Suite 330, Boston, |
| * MA 02111-1307 USA |
| */ |
| |
| /* |
| * SBC8641D board configuration file |
| * |
| * Make sure you change the MAC address and other network params first, |
| * search for CONFIG_ETHADDR, CONFIG_SERVERIP, etc in this file. |
| */ |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| /* High Level Configuration Options */ |
| #define CONFIG_MPC86xx 1 /* MPC86xx */ |
| #define CONFIG_MPC8641 1 /* MPC8641 specific */ |
| #define CONFIG_SBC8641D 1 /* SBC8641D board specific */ |
| #define CONFIG_NUM_CPUS 2 /* Number of CPUs in the system */ |
| #define CONFIG_LINUX_RESET_VEC 0x100 /* Reset vector used by Linux */ |
| |
| #ifdef RUN_DIAG |
| #define CONFIG_SYS_DIAG_ADDR 0xff800000 |
| #endif |
| |
| #define CONFIG_SYS_RESET_ADDRESS 0xfff00100 |
| |
| #define CONFIG_PCI 1 /* Enable PCIE */ |
| #define CONFIG_PCI1 1 /* PCIE controler 1 (slot 1) */ |
| #define CONFIG_PCI2 1 /* PCIE controler 2 (slot 2) */ |
| #define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */ |
| #define CONFIG_FSL_LAW 1 /* Use common FSL init code */ |
| |
| #define CONFIG_TSEC_ENET /* tsec ethernet support */ |
| #define CONFIG_ENV_OVERWRITE |
| |
| #define CONFIG_HIGH_BATS 1 /* High BATs supported and enabled */ |
| |
| #undef CONFIG_SPD_EEPROM /* Do not use SPD EEPROM for DDR setup*/ |
| #undef CONFIG_DDR_ECC /* only for ECC DDR module */ |
| #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */ |
| #define CONFIG_MEM_INIT_VALUE 0xDeadBeef |
| #define CONFIG_NUM_DDR_CONTROLLERS 2 |
| #define CACHE_LINE_INTERLEAVING 0x20000000 |
| #define PAGE_INTERLEAVING 0x21000000 |
| #define BANK_INTERLEAVING 0x22000000 |
| #define SUPER_BANK_INTERLEAVING 0x23000000 |
| |
| |
| #define CONFIG_ALTIVEC 1 |
| |
| /* |
| * L2CR setup -- make sure this is right for your board! |
| */ |
| #define CONFIG_SYS_L2 |
| #define L2_INIT 0 |
| #define L2_ENABLE (L2CR_L2E) |
| |
| #ifndef CONFIG_SYS_CLK_FREQ |
| #define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) |
| #endif |
| |
| #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ |
| |
| #undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */ |
| #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest region */ |
| #define CONFIG_SYS_MEMTEST_END 0x00400000 |
| |
| /* |
| * Base addresses -- Note these are effective addresses where the |
| * actual resources get mapped (not physical addresses) |
| */ |
| #define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ |
| #define CONFIG_SYS_CCSRBAR 0xf8000000 /* relocated CCSRBAR */ |
| #define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */ |
| |
| #define CONFIG_SYS_PCI1_ADDR (CONFIG_SYS_CCSRBAR+0x8000) |
| #define CONFIG_SYS_PCI2_ADDR (CONFIG_SYS_CCSRBAR+0x9000) |
| |
| /* |
| * DDR Setup |
| */ |
| #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory */ |
| #define CONFIG_SYS_DDR_SDRAM_BASE2 0x10000000 /* DDR bank 2 */ |
| #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE |
| #define CONFIG_SYS_SDRAM_BASE2 CONFIG_SYS_DDR_SDRAM_BASE2 |
| #define CONFIG_VERY_BIG_RAM |
| |
| #define MPC86xx_DDR_SDRAM_CLK_CNTL |
| |
| #define CONFIG_NUM_DDR_CONTROLLERS 2 |
| #define CONFIG_DIMM_SLOTS_PER_CTLR 2 |
| #define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR) |
| |
| #if defined(CONFIG_SPD_EEPROM) |
| /* |
| * Determine DDR configuration from I2C interface. |
| */ |
| #define SPD_EEPROM_ADDRESS1 0x51 /* DDR DIMM */ |
| #define SPD_EEPROM_ADDRESS2 0x52 /* DDR DIMM */ |
| #define SPD_EEPROM_ADDRESS3 0x53 /* DDR DIMM */ |
| #define SPD_EEPROM_ADDRESS4 0x54 /* DDR DIMM */ |
| |
| #else |
| /* |
| * Manually set up DDR1 & DDR2 parameters |
| */ |
| |
| #define CONFIG_SYS_SDRAM_SIZE 512 /* DDR is 512MB */ |
| |
| #define CONFIG_SYS_DDR_CS0_BNDS 0x0000000F |
| #define CONFIG_SYS_DDR_CS1_BNDS 0x00000000 |
| #define CONFIG_SYS_DDR_CS2_BNDS 0x00000000 |
| #define CONFIG_SYS_DDR_CS3_BNDS 0x00000000 |
| #define CONFIG_SYS_DDR_CS0_CONFIG 0x80010102 |
| #define CONFIG_SYS_DDR_CS1_CONFIG 0x00000000 |
| #define CONFIG_SYS_DDR_CS2_CONFIG 0x00000000 |
| #define CONFIG_SYS_DDR_CS3_CONFIG 0x00000000 |
| #define CONFIG_SYS_DDR_TIMING_3 0x00000000 |
| #define CONFIG_SYS_DDR_TIMING_0 0x00220802 |
| #define CONFIG_SYS_DDR_TIMING_1 0x38377322 |
| #define CONFIG_SYS_DDR_TIMING_2 0x002040c7 |
| #define CONFIG_SYS_DDR_CFG_1A 0x43008008 |
| #define CONFIG_SYS_DDR_CFG_2 0x24401000 |
| #define CONFIG_SYS_DDR_MODE_1 0x23c00542 |
| #define CONFIG_SYS_DDR_MODE_2 0x00000000 |
| #define CONFIG_SYS_DDR_MODE_CTL 0x00000000 |
| #define CONFIG_SYS_DDR_INTERVAL 0x05080100 |
| #define CONFIG_SYS_DDR_DATA_INIT 0x00000000 |
| #define CONFIG_SYS_DDR_CLK_CTRL 0x03800000 |
| #define CONFIG_SYS_DDR_CFG_1B 0xC3008008 |
| |
| #define CONFIG_SYS_DDR2_CS0_BNDS 0x0010001F |
| #define CONFIG_SYS_DDR2_CS1_BNDS 0x00000000 |
| #define CONFIG_SYS_DDR2_CS2_BNDS 0x00000000 |
| #define CONFIG_SYS_DDR2_CS3_BNDS 0x00000000 |
| #define CONFIG_SYS_DDR2_CS0_CONFIG 0x80010102 |
| #define CONFIG_SYS_DDR2_CS1_CONFIG 0x00000000 |
| #define CONFIG_SYS_DDR2_CS2_CONFIG 0x00000000 |
| #define CONFIG_SYS_DDR2_CS3_CONFIG 0x00000000 |
| #define CONFIG_SYS_DDR2_EXT_REFRESH 0x00000000 |
| #define CONFIG_SYS_DDR2_TIMING_0 0x00220802 |
| #define CONFIG_SYS_DDR2_TIMING_1 0x38377322 |
| #define CONFIG_SYS_DDR2_TIMING_2 0x002040c7 |
| #define CONFIG_SYS_DDR2_CFG_1A 0x43008008 |
| #define CONFIG_SYS_DDR2_CFG_2 0x24401000 |
| #define CONFIG_SYS_DDR2_MODE_1 0x23c00542 |
| #define CONFIG_SYS_DDR2_MODE_2 0x00000000 |
| #define CONFIG_SYS_DDR2_MODE_CTL 0x00000000 |
| #define CONFIG_SYS_DDR2_INTERVAL 0x05080100 |
| #define CONFIG_SYS_DDR2_DATA_INIT 0x00000000 |
| #define CONFIG_SYS_DDR2_CLK_CTRL 0x03800000 |
| #define CONFIG_SYS_DDR2_CFG_1B 0xC3008008 |
| |
| |
| #endif |
| |
| /* #define CONFIG_ID_EEPROM 1 |
| #define ID_EEPROM_ADDR 0x57 */ |
| |
| /* |
| * The SBC8641D contains 16MB flash space at ff000000. |
| */ |
| #define CONFIG_SYS_FLASH_BASE 0xff000000 /* start of FLASH 16M */ |
| |
| /* Flash */ |
| #define CONFIG_SYS_BR0_PRELIM 0xff001001 /* port size 16bit */ |
| #define CONFIG_SYS_OR0_PRELIM 0xff006e65 /* 16MB Boot Flash area */ |
| |
| /* 64KB EEPROM */ |
| #define CONFIG_SYS_BR1_PRELIM 0xf0000801 /* port size 16bit */ |
| #define CONFIG_SYS_OR1_PRELIM 0xffff6e65 /* 64K EEPROM area */ |
| |
| /* EPLD - User switches, board id, LEDs */ |
| #define CONFIG_SYS_BR2_PRELIM 0xf1000801 /* port size 16bit */ |
| #define CONFIG_SYS_OR2_PRELIM 0xfff06e65 /* EPLD (switches, board ID, LEDs) area */ |
| |
| /* Local bus SDRAM 128MB */ |
| #define CONFIG_SYS_BR3_PRELIM 0xe0001861 /* port size ?bit */ |
| #define CONFIG_SYS_OR3_PRELIM 0xfc006cc0 /* 128MB local bus SDRAM area (1st half) */ |
| #define CONFIG_SYS_BR4_PRELIM 0xe4001861 /* port size ?bit */ |
| #define CONFIG_SYS_OR4_PRELIM 0xfc006cc0 /* 128MB local bus SDRAM area (2nd half) */ |
| |
| /* Disk on Chip (DOC) 128MB */ |
| #define CONFIG_SYS_BR5_PRELIM 0xe8001001 /* port size ?bit */ |
| #define CONFIG_SYS_OR5_PRELIM 0xf8006e65 /* 128MB local bus SDRAM area (2nd half) */ |
| |
| /* LCD */ |
| #define CONFIG_SYS_BR6_PRELIM 0xf4000801 /* port size ?bit */ |
| #define CONFIG_SYS_OR6_PRELIM 0xfff06e65 /* 128MB local bus SDRAM area (2nd half) */ |
| |
| /* Control logic & misc peripherals */ |
| #define CONFIG_SYS_BR7_PRELIM 0xf2000801 /* port size ?bit */ |
| #define CONFIG_SYS_OR7_PRELIM 0xfff06e65 /* 128MB local bus SDRAM area (2nd half) */ |
| |
| #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ |
| #define CONFIG_SYS_MAX_FLASH_SECT 131 /* sectors per device */ |
| |
| #undef CONFIG_SYS_FLASH_CHECKSUM |
| #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ |
| #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ |
| #define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */ |
| |
| #define CONFIG_FLASH_CFI_DRIVER |
| #define CONFIG_SYS_FLASH_CFI |
| #define CONFIG_SYS_WRITE_SWAPPED_DATA |
| #define CONFIG_SYS_FLASH_EMPTY_INFO |
| #define CONFIG_SYS_FLASH_PROTECTION |
| |
| #undef CONFIG_CLOCKS_IN_MHZ |
| |
| #define CONFIG_L1_INIT_RAM |
| #define CONFIG_SYS_INIT_RAM_LOCK 1 |
| #ifndef CONFIG_SYS_INIT_RAM_LOCK |
| #define CONFIG_SYS_INIT_RAM_ADDR 0x0fd00000 /* Initial RAM address */ |
| #else |
| #define CONFIG_SYS_INIT_RAM_ADDR 0xf8400000 /* Initial RAM address */ |
| #endif |
| #define CONFIG_SYS_INIT_RAM_END 0x4000 /* End of used area in RAM */ |
| |
| #define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data */ |
| #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) |
| #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET |
| |
| #define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ |
| #define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ |
| |
| /* Serial Port */ |
| #define CONFIG_CONS_INDEX 1 |
| #undef CONFIG_SERIAL_SOFTWARE_FIFO |
| #define CONFIG_SYS_NS16550 |
| #define CONFIG_SYS_NS16550_SERIAL |
| #define CONFIG_SYS_NS16550_REG_SIZE 1 |
| #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) |
| |
| #define CONFIG_SYS_BAUDRATE_TABLE \ |
| {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} |
| |
| #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) |
| #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) |
| |
| /* Use the HUSH parser */ |
| #define CONFIG_SYS_HUSH_PARSER |
| #ifdef CONFIG_SYS_HUSH_PARSER |
| #define CONFIG_SYS_PROMPT_HUSH_PS2 "> " |
| #endif |
| |
| /* |
| * Pass open firmware flat tree to kernel |
| */ |
| #define CONFIG_OF_LIBFDT 1 |
| #define CONFIG_OF_BOARD_SETUP 1 |
| #define CONFIG_OF_STDOUT_VIA_ALIAS 1 |
| |
| #define CONFIG_SYS_64BIT_VSPRINTF 1 |
| #define CONFIG_SYS_64BIT_STRTOUL 1 |
| |
| /* |
| * I2C |
| */ |
| #define CONFIG_FSL_I2C /* Use FSL common I2C driver */ |
| #define CONFIG_HARD_I2C /* I2C with hardware support*/ |
| #undef CONFIG_SOFT_I2C /* I2C bit-banged */ |
| #define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ |
| #define CONFIG_SYS_I2C_SLAVE 0x7F |
| #define CONFIG_SYS_I2C_NOPROBES {0x69} /* Don't probe these addrs */ |
| #define CONFIG_SYS_I2C_OFFSET 0x3100 |
| |
| /* |
| * RapidIO MMU |
| */ |
| #define CONFIG_SYS_RIO_MEM_BASE 0xc0000000 /* base address */ |
| #define CONFIG_SYS_RIO_MEM_PHYS CONFIG_SYS_RIO_MEM_BASE |
| #define CONFIG_SYS_RIO_MEM_SIZE 0x20000000 /* 128M */ |
| |
| /* |
| * General PCI |
| * Addresses are mapped 1-1. |
| */ |
| #define CONFIG_SYS_PCI1_MEM_BASE 0x80000000 |
| #define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE |
| #define CONFIG_SYS_PCI1_MEM_SIZE 0x20000000 /* 512M */ |
| #define CONFIG_SYS_PCI1_IO_BASE 0xe2000000 |
| #define CONFIG_SYS_PCI1_IO_PHYS CONFIG_SYS_PCI1_IO_BASE |
| #define CONFIG_SYS_PCI1_IO_SIZE 0x1000000 /* 16M */ |
| |
| /* PCI view of System Memory */ |
| #define CONFIG_SYS_PCI_MEMORY_BUS 0x00000000 |
| #define CONFIG_SYS_PCI_MEMORY_PHYS 0x00000000 |
| #define CONFIG_SYS_PCI_MEMORY_SIZE 0x80000000 |
| |
| #define CONFIG_SYS_PCI2_MEM_BASE 0xa0000000 |
| #define CONFIG_SYS_PCI2_MEM_PHYS CONFIG_SYS_PCI2_MEM_BASE |
| #define CONFIG_SYS_PCI2_MEM_SIZE 0x10000000 /* 256M */ |
| #define CONFIG_SYS_PCI2_IO_BASE 0xe3000000 |
| #define CONFIG_SYS_PCI2_IO_PHYS CONFIG_SYS_PCI2_IO_BASE |
| #define CONFIG_SYS_PCI2_IO_SIZE 0x1000000 /* 16M */ |
| |
| #if defined(CONFIG_PCI) |
| |
| #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ |
| |
| #undef CONFIG_SYS_SCSI_SCAN_BUS_REVERSE |
| |
| #define CONFIG_NET_MULTI |
| #define CONFIG_PCI_PNP /* do pci plug-and-play */ |
| |
| #undef CONFIG_EEPRO100 |
| #undef CONFIG_TULIP |
| |
| #if !defined(CONFIG_PCI_PNP) |
| #define PCI_ENET0_IOADDR 0xe0000000 |
| #define PCI_ENET0_MEMADDR 0xe0000000 |
| #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */ |
| #endif |
| |
| #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ |
| |
| #define CONFIG_DOS_PARTITION |
| #undef CONFIG_SCSI_AHCI |
| |
| #ifdef CONFIG_SCSI_AHCI |
| #define CONFIG_SATA_ULI5288 |
| #define CONFIG_SYS_SCSI_MAX_SCSI_ID 4 |
| #define CONFIG_SYS_SCSI_MAX_LUN 1 |
| #define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * CONFIG_SYS_SCSI_MAX_LUN) |
| #define CONFIG_SYS_SCSI_MAXDEVICE CONFIG_SYS_SCSI_MAX_DEVICE |
| #endif |
| |
| #endif /* CONFIG_PCI */ |
| |
| #if defined(CONFIG_TSEC_ENET) |
| |
| #ifndef CONFIG_NET_MULTI |
| #define CONFIG_NET_MULTI 1 |
| #endif |
| |
| /* #define CONFIG_MII 1 */ /* MII PHY management */ |
| |
| #define CONFIG_TSEC1 1 |
| #define CONFIG_TSEC1_NAME "eTSEC1" |
| #define CONFIG_TSEC2 1 |
| #define CONFIG_TSEC2_NAME "eTSEC2" |
| #define CONFIG_TSEC3 1 |
| #define CONFIG_TSEC3_NAME "eTSEC3" |
| #define CONFIG_TSEC4 1 |
| #define CONFIG_TSEC4_NAME "eTSEC4" |
| |
| #define TSEC1_PHY_ADDR 0x1F |
| #define TSEC2_PHY_ADDR 0x00 |
| #define TSEC3_PHY_ADDR 0x01 |
| #define TSEC4_PHY_ADDR 0x02 |
| #define TSEC1_PHYIDX 0 |
| #define TSEC2_PHYIDX 0 |
| #define TSEC3_PHYIDX 0 |
| #define TSEC4_PHYIDX 0 |
| #define TSEC1_FLAGS TSEC_GIGABIT |
| #define TSEC2_FLAGS TSEC_GIGABIT |
| #define TSEC3_FLAGS TSEC_GIGABIT |
| #define TSEC4_FLAGS TSEC_GIGABIT |
| |
| #define CONFIG_SYS_TBIPA_VALUE 0x1e /* Set TBI address not to conflict with TSEC1_PHY_ADDR */ |
| |
| #define CONFIG_ETHPRIME "eTSEC1" |
| |
| #endif /* CONFIG_TSEC_ENET */ |
| |
| /* |
| * BAT0 2G Cacheable, non-guarded |
| * 0x0000_0000 2G DDR |
| */ |
| #define CONFIG_SYS_DBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE) |
| #define CONFIG_SYS_DBAT0U (BATU_BL_2G | BATU_VS | BATU_VP) |
| #define CONFIG_SYS_IBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE ) |
| #define CONFIG_SYS_IBAT0U CONFIG_SYS_DBAT0U |
| |
| /* |
| * BAT1 1G Cache-inhibited, guarded |
| * 0x8000_0000 512M PCI-Express 1 Memory |
| * 0xa000_0000 512M PCI-Express 2 Memory |
| * Changed it for operating from 0xd0000000 |
| */ |
| #define CONFIG_SYS_DBAT1L ( CONFIG_SYS_PCI1_MEM_BASE | BATL_PP_RW \ |
| | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) |
| #define CONFIG_SYS_DBAT1U (CONFIG_SYS_PCI1_MEM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) |
| #define CONFIG_SYS_IBAT1L (CONFIG_SYS_PCI1_MEM_BASE | BATL_PP_RW | BATL_CACHEINHIBIT) |
| #define CONFIG_SYS_IBAT1U CONFIG_SYS_DBAT1U |
| |
| /* |
| * BAT2 512M Cache-inhibited, guarded |
| * 0xc000_0000 512M RapidIO Memory |
| */ |
| #define CONFIG_SYS_DBAT2L (CONFIG_SYS_RIO_MEM_BASE | BATL_PP_RW \ |
| | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) |
| #define CONFIG_SYS_DBAT2U (CONFIG_SYS_RIO_MEM_BASE | BATU_BL_512M | BATU_VS | BATU_VP) |
| #define CONFIG_SYS_IBAT2L (CONFIG_SYS_RIO_MEM_BASE | BATL_PP_RW | BATL_CACHEINHIBIT) |
| #define CONFIG_SYS_IBAT2U CONFIG_SYS_DBAT2U |
| |
| /* |
| * BAT3 4M Cache-inhibited, guarded |
| * 0xf800_0000 4M CCSR |
| */ |
| #define CONFIG_SYS_DBAT3L ( CONFIG_SYS_CCSRBAR | BATL_PP_RW \ |
| | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) |
| #define CONFIG_SYS_DBAT3U (CONFIG_SYS_CCSRBAR | BATU_BL_4M | BATU_VS | BATU_VP) |
| #define CONFIG_SYS_IBAT3L (CONFIG_SYS_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT) |
| #define CONFIG_SYS_IBAT3U CONFIG_SYS_DBAT3U |
| |
| /* |
| * BAT4 32M Cache-inhibited, guarded |
| * 0xe200_0000 16M PCI-Express 1 I/O |
| * 0xe300_0000 16M PCI-Express 2 I/0 |
| * Note that this is at 0xe0000000 |
| */ |
| #define CONFIG_SYS_DBAT4L ( CONFIG_SYS_PCI1_IO_BASE | BATL_PP_RW \ |
| | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) |
| #define CONFIG_SYS_DBAT4U (CONFIG_SYS_PCI1_IO_BASE | BATU_BL_32M | BATU_VS | BATU_VP) |
| #define CONFIG_SYS_IBAT4L (CONFIG_SYS_PCI1_IO_BASE | BATL_PP_RW | BATL_CACHEINHIBIT) |
| #define CONFIG_SYS_IBAT4U CONFIG_SYS_DBAT4U |
| |
| /* |
| * BAT5 128K Cacheable, non-guarded |
| * 0xe401_0000 128K Init RAM for stack in the CPU DCache (no backing memory) |
| */ |
| #define CONFIG_SYS_DBAT5L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE) |
| #define CONFIG_SYS_DBAT5U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP) |
| #define CONFIG_SYS_IBAT5L CONFIG_SYS_DBAT5L |
| #define CONFIG_SYS_IBAT5U CONFIG_SYS_DBAT5U |
| |
| /* |
| * BAT6 32M Cache-inhibited, guarded |
| * 0xfe00_0000 32M FLASH |
| */ |
| #define CONFIG_SYS_DBAT6L ((CONFIG_SYS_FLASH_BASE & 0xfe000000) | BATL_PP_RW \ |
| | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) |
| #define CONFIG_SYS_DBAT6U ((CONFIG_SYS_FLASH_BASE & 0xfe000000) | BATU_BL_32M | BATU_VS | BATU_VP) |
| #define CONFIG_SYS_IBAT6L ((CONFIG_SYS_FLASH_BASE & 0xfe000000) | BATL_PP_RW | BATL_MEMCOHERENCE) |
| #define CONFIG_SYS_IBAT6U CONFIG_SYS_DBAT6U |
| |
| #define CONFIG_SYS_DBAT7L 0x00000000 |
| #define CONFIG_SYS_DBAT7U 0x00000000 |
| #define CONFIG_SYS_IBAT7L 0x00000000 |
| #define CONFIG_SYS_IBAT7U 0x00000000 |
| |
| /* |
| * Environment |
| */ |
| #define CONFIG_ENV_IS_IN_FLASH 1 |
| #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0x40000) |
| #define CONFIG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */ |
| #define CONFIG_ENV_SIZE 0x2000 |
| |
| #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ |
| #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ |
| |
| #include <config_cmd_default.h> |
| #define CONFIG_CMD_PING |
| #define CONFIG_CMD_I2C |
| #define CONFIG_CMD_REGINFO |
| |
| #if defined(CONFIG_PCI) |
| #define CONFIG_CMD_PCI |
| #endif |
| |
| #undef CONFIG_WATCHDOG /* watchdog disabled */ |
| |
| /* |
| * Miscellaneous configurable options |
| */ |
| #define CONFIG_SYS_LONGHELP /* undef to save memory */ |
| #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ |
| #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ |
| |
| #if defined(CONFIG_CMD_KGDB) |
| #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ |
| #else |
| #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ |
| #endif |
| |
| #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ |
| #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ |
| #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ |
| #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ |
| |
| /* |
| * For booting Linux, the board info and command line data |
| * have to be in the first 8 MB of memory, since this is |
| * the maximum mapped by the Linux kernel during initialization. |
| */ |
| #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ |
| |
| /* Cache Configuration */ |
| #define CONFIG_SYS_DCACHE_SIZE 32768 |
| #define CONFIG_SYS_CACHELINE_SIZE 32 |
| #if defined(CONFIG_CMD_KGDB) |
| #define CONFIG_SYS_CACHELINE_SHIFT 5 /*log base 2 of the above value*/ |
| #endif |
| |
| /* |
| * Internal Definitions |
| * |
| * Boot Flags |
| */ |
| #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ |
| #define BOOTFLAG_WARM 0x02 /* Software reboot */ |
| |
| #if defined(CONFIG_CMD_KGDB) |
| #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ |
| #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ |
| #endif |
| |
| /* |
| * Environment Configuration |
| */ |
| |
| /* The mac addresses for all ethernet interface */ |
| #if defined(CONFIG_TSEC_ENET) |
| #define CONFIG_ETHADDR 02:E0:0C:00:00:01 |
| #define CONFIG_ETH1ADDR 02:E0:0C:00:01:FD |
| #define CONFIG_ETH2ADDR 02:E0:0C:00:02:FD |
| #define CONFIG_ETH3ADDR 02:E0:0C:00:03:FD |
| #endif |
| |
| #define CONFIG_HAS_ETH0 1 |
| #define CONFIG_HAS_ETH1 1 |
| #define CONFIG_HAS_ETH2 1 |
| #define CONFIG_HAS_ETH3 1 |
| |
| #define CONFIG_IPADDR 192.168.0.50 |
| |
| #define CONFIG_HOSTNAME sbc8641d |
| #define CONFIG_ROOTPATH /opt/eldk/ppc_74xx |
| #define CONFIG_BOOTFILE uImage |
| |
| #define CONFIG_SERVERIP 192.168.0.2 |
| #define CONFIG_GATEWAYIP 192.168.0.1 |
| #define CONFIG_NETMASK 255.255.255.0 |
| |
| /* default location for tftp and bootm */ |
| #define CONFIG_LOADADDR 1000000 |
| |
| #define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ |
| #undef CONFIG_BOOTARGS /* the boot command will set bootargs */ |
| |
| #define CONFIG_BAUDRATE 115200 |
| |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| "netdev=eth0\0" \ |
| "consoledev=ttyS0\0" \ |
| "ramdiskaddr=2000000\0" \ |
| "ramdiskfile=uRamdisk\0" \ |
| "dtbaddr=400000\0" \ |
| "dtbfile=sbc8641d.dtb\0" \ |
| "en-wd=mw.b f8100010 0x08; echo -expect:- 08; md.b f8100010 1\0" \ |
| "dis-wd=mw.b f8100010 0x00; echo -expect:- 00; md.b f8100010 1\0" \ |
| "maxcpus=1" |
| |
| #define CONFIG_NFSBOOTCOMMAND \ |
| "setenv bootargs root=/dev/nfs rw " \ |
| "nfsroot=$serverip:$rootpath " \ |
| "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ |
| "console=$consoledev,$baudrate $othbootargs;" \ |
| "tftp $loadaddr $bootfile;" \ |
| "tftp $dtbaddr $dtbfile;" \ |
| "bootm $loadaddr - $dtbaddr" |
| |
| #define CONFIG_RAMBOOTCOMMAND \ |
| "setenv bootargs root=/dev/ram rw " \ |
| "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ |
| "console=$consoledev,$baudrate $othbootargs;" \ |
| "tftp $ramdiskaddr $ramdiskfile;" \ |
| "tftp $loadaddr $bootfile;" \ |
| "tftp $dtbaddr $dtbfile;" \ |
| "bootm $loadaddr $ramdiskaddr $dtbaddr" |
| |
| #define CONFIG_FLASHBOOTCOMMAND \ |
| "setenv bootargs root=/dev/ram rw " \ |
| "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ |
| "console=$consoledev,$baudrate $othbootargs;" \ |
| "bootm ffd00000 ffb00000 ffa00000" |
| |
| #define CONFIG_BOOTCOMMAND CONFIG_FLASHBOOTCOMMAND |
| |
| #endif /* __CONFIG_H */ |