include/configs/u8500_href.h - github/trini/u-boot - Gitiles

 /*
  * Copyright (C) ST-Ericsson SA 2009
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */

 #ifndef __CONFIG_H
 #define __CONFIG_H

 /*
  * High Level Configuration Options
  * (easy to change)
  */
 #define CONFIG_U8500

 #define CONFIG_SYS_MEMTEST_START	0x00000000
 #define CONFIG_SYS_MEMTEST_END	0x1FFFFFFF

 #define CONFIG_BOARD_EARLY_INIT_F
 #define CONFIG_BOARD_LATE_INIT

 /*
  * Size of malloc() pool
  */
 #ifdef CONFIG_BOOT_SRAM
 #define CONFIG_ENV_SIZE		(32*1024)
 #define CONFIG_SYS_MALLOC_LEN	(CONFIG_ENV_SIZE + 64*1024)
 #else
 #define CONFIG_ENV_SIZE		(128*1024)
 #define CONFIG_SYS_MALLOC_LEN	(CONFIG_ENV_SIZE + 256*1024)
 #endif
 #define CONFIG_SYS_GBL_DATA_SIZE	128	/* for initial data */

 /*
  * PL011 Configuration
  */
 #define CONFIG_PL011_SERIAL
 #define CONFIG_PL011_SERIAL_RLCR
 #define CONFIG_PL011_SERIAL_FLUSH_ON_INIT

 /*
  * U8500 UART registers base for 3 serial devices
  */
 #define CFG_UART0_BASE		0x80120000
 #define CFG_UART1_BASE		0x80121000
 #define CFG_UART2_BASE		0x80007000
 #define CFG_SERIAL0		CFG_UART0_BASE
 #define CFG_SERIAL1		CFG_UART1_BASE
 #define CFG_SERIAL2		CFG_UART2_BASE
 #define CONFIG_PL011_CLOCK	38400000
 #define CONFIG_PL01x_PORTS	{ (void *)CFG_SERIAL0, (void *)CFG_SERIAL1, \
 				  (void *)CFG_SERIAL2 }
 #define CONFIG_CONS_INDEX	2
 #define CONFIG_BAUDRATE		115200

 /*
  * Devices and file systems
  */
 #define CONFIG_MMC
 #define CONFIG_GENERIC_MMC
 #define CONFIG_DOS_PARTITION

 /*
  * Commands
  */
 #define CONFIG_CMD_MEMORY
 #define CONFIG_CMD_BOOTD
 #define CONFIG_CMD_BDI
 #define CONFIG_CMD_IMI
 #define CONFIG_CMD_MISC
 #define CONFIG_CMD_RUN
 #define CONFIG_CMD_ECHO
 #define CONFIG_CMD_CONSOLE
 #define CONFIG_CMD_LOADS
 #define CONFIG_CMD_LOADB
 #define CONFIG_CMD_MMC
 #define CONFIG_CMD_FAT
 #define CONFIG_CMD_EXT2
 #define CONFIG_CMD_SOURCE
 #define CONFIG_CMD_I2C

 #ifndef CONFIG_BOOTDELAY
 #define CONFIG_BOOTDELAY	1
 #endif
 #define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */

 #undef CONFIG_BOOTARGS
 #define CONFIG_BOOTCOMMAND	"run emmcboot"

 #define CONFIG_EXTRA_ENV_SETTINGS \
 	"verify=n\0"							\
 	"loadaddr=0x00100000\0"						\
 	"console=ttyAMA2,115200n8\0"					\
 	"memargs256=mem=96M@0 mem_modem=32M@96M mem=30M@128M "		\
 		"pmem=22M@158M pmem_hwb=44M@180M mem_mali=32@224M\0"	\
 	"memargs512=mem=96M@0 mem_modem=32M@96M mem=44M@128M "		\
 		"pmem=22M@172M mem=30M@194M mem_mali=32M@224M "		\
 		"pmem_hwb=54M@256M mem=202M@310M\0"			\
 	"commonargs=setenv bootargs cachepolicy=writealloc noinitrd "	\
 		"init=init "						\
 		"board_id=${board_id} "					\
 		"logo.${logo} "						\
 		"startup_graphics=${startup_graphics}\0"		\
 	"emmcargs=setenv bootargs ${bootargs} "				\
 		"root=/dev/mmcblk0p2 "					\
 		"rootdelay=1\0"						\
 	"addcons=setenv bootargs ${bootargs} "				\
 		"console=${console}\0"					\
 	"emmcboot=echo Booting from eMMC ...; "				\
 		"run commonargs emmcargs addcons memargs;"		\
 		"mmc read 0 ${loadaddr} 0xA0000 0x4000;"		\
 		"bootm ${loadaddr}\0"					\
 	"flash=mmc init 1;fatload mmc 1 ${loadaddr} flash.scr;"		\
 		"source ${loadaddr}\0"					\
 	"loaduimage=mmc init 1;fatload mmc 1 ${loadaddr} uImage\0"	\
 	"usbtty=cdc_acm\0"						\
 	"stdout=serial,usbtty\0"					\
 	"stdin=serial,usbtty\0"						\
 	"stderr=serial,usbtty\0"

 /*
  * Miscellaneous configurable options
  */

 #define CONFIG_SYS_LONGHELP			/* undef to save memory     */
 #define CONFIG_SYS_PROMPT	"U8500 $ "	/* Monitor Command Prompt   */
 #define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size  */

 /* Print Buffer Size */
 #define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE \
 					+ sizeof(CONFIG_SYS_PROMPT) + 16)
 #define CONFIG_SYS_MAXARGS	32	/* max number of command args */
 #define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE /* Boot Arg Buffer Size */

 #undef	CONFIG_SYS_CLKS_IN_HZ		/* everything, incl board info, in Hz */
 #define CONFIG_SYS_LOAD_ADDR		0x00100000 /* default load address */
 #define CONFIG_SYS_LOADS_BAUD_CHANGE

 #define CONFIG_SYS_HUSH_PARSER
 #define CONFIG_CMDLINE_EDITING

 #define CONFIG_SETUP_MEMORY_TAGS	2
 #define CONFIG_INITRD_TAG
 #define CONFIG_CMDLINE_TAG			/* enable passing of ATAGs  */

 /*
  * I2C
  */
 #define CONFIG_U8500_I2C
 #undef	CONFIG_HARD_I2C			/* I2C with hardware support */
 #define CONFIG_I2C_MULTI_BUS
 #define CONFIG_SYS_I2C_SPEED		100000
 #define CONFIG_SYS_I2C_SLAVE		0	/* slave addr of controller */
 #define CONFIG_SYS_U8500_I2C0_BASE		0x80004000
 #define CONFIG_SYS_U8500_I2C1_BASE		0x80122000
 #define CONFIG_SYS_U8500_I2C2_BASE		0x80128000
 #define CONFIG_SYS_U8500_I2C3_BASE		0x80110000
 #define CONFIG_SYS_U8500_I2C_BUS_MAX		4

 #define CONFIG_SYS_I2C_GPIOE_ADDR	0x42	/* GPIO expander chip addr */
 #define CONFIG_TC35892_GPIO

 /*
  * Physical Memory Map
  */
 #define CONFIG_NR_DRAM_BANKS		1
 #define PHYS_SDRAM_1			0x00000000	/* DDR-SDRAM Bank #1 */
 #define PHYS_SDRAM_SIZE_1		0x20000000	/* 512 MB */

 /*
  * additions for new relocation code
  */
 #define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_1
 #define CONFIG_SYS_INIT_RAM_SIZE	0x100000
 #define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_SDRAM_BASE + \
 					 CONFIG_SYS_INIT_RAM_SIZE - \
 					 GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_ADDR		CONFIG_SYS_GBL_DATA_OFFSET

 /* landing address before relocation */
 #ifndef CONFIG_SYS_TEXT_BASE
 #define CONFIG_SYS_TEXT_BASE            0x0
 #endif

 /*
  * MMC related configs
  * NB Only externa SD slot is currently supported
  */
 #define MMC_BLOCK_SIZE			512
 #define CONFIG_ARM_PL180_MMCI
 #define CONFIG_ARM_PL180_MMCI_BASE	0x80126000	/* MMC base for 8500  */
 #define CONFIG_ARM_PL180_MMCI_CLOCK_FREQ 6250000
 #define CONFIG_MMC_DEV_NUM		1

 #define CONFIG_CMD_ENV
 #define CONFIG_CMD_SAVEENV	/* CMD_ENV is obsolete but used in env_emmc.c */
 #define CONFIG_ENV_IS_IN_MMC
 #define CONFIG_ENV_OFFSET		0x13F80000
 #define CONFIG_SYS_MMC_ENV_DEV          0               /* SLOT2: eMMC */

 /*
  * FLASH and environment organization
  */
 #define CONFIG_SYS_NO_FLASH

 /*
  * base register values for U8500
  */
 #define CFG_PRCMU_BASE		0x80157000	/* Power, reset and clock
 						   management unit */
 #define CFG_FSMC_BASE		0x80000000	/* FSMC Controller */

 #endif	/* __CONFIG_H */
	/*
	* Copyright (C) ST-Ericsson SA 2009
	*
	* SPDX-License-Identifier: GPL-2.0+
	*/

	#ifndef __CONFIG_H
	#define __CONFIG_H

	/*
	* High Level Configuration Options
	* (easy to change)
	*/
	#define CONFIG_U8500

	#define CONFIG_SYS_MEMTEST_START 0x00000000
	#define CONFIG_SYS_MEMTEST_END 0x1FFFFFFF

	#define CONFIG_BOARD_EARLY_INIT_F
	#define CONFIG_BOARD_LATE_INIT

	/*
	* Size of malloc() pool
	*/
	#ifdef CONFIG_BOOT_SRAM
	#define CONFIG_ENV_SIZE (32*1024)
	#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 64*1024)
	#else
	#define CONFIG_ENV_SIZE (128*1024)
	#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 256*1024)
	#endif
	#define CONFIG_SYS_GBL_DATA_SIZE 128 /* for initial data */

	/*
	* PL011 Configuration
	*/
	#define CONFIG_PL011_SERIAL
	#define CONFIG_PL011_SERIAL_RLCR
	#define CONFIG_PL011_SERIAL_FLUSH_ON_INIT

	/*
	* U8500 UART registers base for 3 serial devices
	*/
	#define CFG_UART0_BASE 0x80120000
	#define CFG_UART1_BASE 0x80121000
	#define CFG_UART2_BASE 0x80007000
	#define CFG_SERIAL0 CFG_UART0_BASE
	#define CFG_SERIAL1 CFG_UART1_BASE
	#define CFG_SERIAL2 CFG_UART2_BASE
	#define CONFIG_PL011_CLOCK 38400000
	#define CONFIG_PL01x_PORTS { (void )CFG_SERIAL0, (void )CFG_SERIAL1, \
	(void *)CFG_SERIAL2 }
	#define CONFIG_CONS_INDEX 2
	#define CONFIG_BAUDRATE 115200

	/*
	* Devices and file systems
	*/
	#define CONFIG_MMC
	#define CONFIG_GENERIC_MMC
	#define CONFIG_DOS_PARTITION

	/*
	* Commands
	*/
	#define CONFIG_CMD_MEMORY
	#define CONFIG_CMD_BOOTD
	#define CONFIG_CMD_BDI
	#define CONFIG_CMD_IMI
	#define CONFIG_CMD_MISC
	#define CONFIG_CMD_RUN
	#define CONFIG_CMD_ECHO
	#define CONFIG_CMD_CONSOLE
	#define CONFIG_CMD_LOADS
	#define CONFIG_CMD_LOADB
	#define CONFIG_CMD_MMC
	#define CONFIG_CMD_FAT
	#define CONFIG_CMD_EXT2
	#define CONFIG_CMD_SOURCE
	#define CONFIG_CMD_I2C

	#ifndef CONFIG_BOOTDELAY
	#define CONFIG_BOOTDELAY 1
	#endif
	#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */

	#undef CONFIG_BOOTARGS
	#define CONFIG_BOOTCOMMAND "run emmcboot"

	#define CONFIG_EXTRA_ENV_SETTINGS \
	"verify=n\0" \
	"loadaddr=0x00100000\0" \
	"console=ttyAMA2,115200n8\0" \
	"memargs256=mem=96M@0 mem_modem=32M@96M mem=30M@128M " \
	"pmem=22M@158M pmem_hwb=44M@180M mem_mali=32@224M\0" \
	"memargs512=mem=96M@0 mem_modem=32M@96M mem=44M@128M " \
	"pmem=22M@172M mem=30M@194M mem_mali=32M@224M " \
	"pmem_hwb=54M@256M mem=202M@310M\0" \
	"commonargs=setenv bootargs cachepolicy=writealloc noinitrd " \
	"init=init " \
	"board_id=${board_id} " \
	"logo.${logo} " \
	"startup_graphics=${startup_graphics}\0" \
	"emmcargs=setenv bootargs ${bootargs} " \
	"root=/dev/mmcblk0p2 " \
	"rootdelay=1\0" \
	"addcons=setenv bootargs ${bootargs} " \
	"console=${console}\0" \
	"emmcboot=echo Booting from eMMC ...; " \
	"run commonargs emmcargs addcons memargs;" \
	"mmc read 0 ${loadaddr} 0xA0000 0x4000;" \
	"bootm ${loadaddr}\0" \
	"flash=mmc init 1;fatload mmc 1 ${loadaddr} flash.scr;" \
	"source ${loadaddr}\0" \
	"loaduimage=mmc init 1;fatload mmc 1 ${loadaddr} uImage\0" \
	"usbtty=cdc_acm\0" \
	"stdout=serial,usbtty\0" \
	"stdin=serial,usbtty\0" \
	"stderr=serial,usbtty\0"

	/*
	* Miscellaneous configurable options
	*/

	#define CONFIG_SYS_LONGHELP /* undef to save memory */
	#define CONFIG_SYS_PROMPT "U8500 $ " /* Monitor Command Prompt */
	#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */

	/* Print Buffer Size */
	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \
	+ sizeof(CONFIG_SYS_PROMPT) + 16)
	#define CONFIG_SYS_MAXARGS 32 /* max number of command args */
	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Arg Buffer Size */

	#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
	#define CONFIG_SYS_LOAD_ADDR 0x00100000 /* default load address */
	#define CONFIG_SYS_LOADS_BAUD_CHANGE

	#define CONFIG_SYS_HUSH_PARSER
	#define CONFIG_CMDLINE_EDITING

	#define CONFIG_SETUP_MEMORY_TAGS 2
	#define CONFIG_INITRD_TAG
	#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */

	/*
	* I2C
	*/
	#define CONFIG_U8500_I2C
	#undef CONFIG_HARD_I2C /* I2C with hardware support */
	#define CONFIG_I2C_MULTI_BUS
	#define CONFIG_SYS_I2C_SPEED 100000
	#define CONFIG_SYS_I2C_SLAVE 0 /* slave addr of controller */
	#define CONFIG_SYS_U8500_I2C0_BASE 0x80004000
	#define CONFIG_SYS_U8500_I2C1_BASE 0x80122000
	#define CONFIG_SYS_U8500_I2C2_BASE 0x80128000
	#define CONFIG_SYS_U8500_I2C3_BASE 0x80110000
	#define CONFIG_SYS_U8500_I2C_BUS_MAX 4

	#define CONFIG_SYS_I2C_GPIOE_ADDR 0x42 /* GPIO expander chip addr */
	#define CONFIG_TC35892_GPIO

	/*
	* Physical Memory Map
	*/
	#define CONFIG_NR_DRAM_BANKS 1
	#define PHYS_SDRAM_1 0x00000000 /* DDR-SDRAM Bank #1 */
	#define PHYS_SDRAM_SIZE_1 0x20000000 /* 512 MB */

	/*
	* additions for new relocation code
	*/
	#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
	#define CONFIG_SYS_INIT_RAM_SIZE 0x100000
	#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_SDRAM_BASE + \
	CONFIG_SYS_INIT_RAM_SIZE - \
	GENERATED_GBL_DATA_SIZE)
	#define CONFIG_SYS_INIT_SP_ADDR CONFIG_SYS_GBL_DATA_OFFSET

	/* landing address before relocation */
	#ifndef CONFIG_SYS_TEXT_BASE
	#define CONFIG_SYS_TEXT_BASE 0x0
	#endif

	/*
	* MMC related configs
	* NB Only externa SD slot is currently supported
	*/
	#define MMC_BLOCK_SIZE 512
	#define CONFIG_ARM_PL180_MMCI
	#define CONFIG_ARM_PL180_MMCI_BASE 0x80126000 /* MMC base for 8500 */
	#define CONFIG_ARM_PL180_MMCI_CLOCK_FREQ 6250000
	#define CONFIG_MMC_DEV_NUM 1

	#define CONFIG_CMD_ENV
	#define CONFIG_CMD_SAVEENV /* CMD_ENV is obsolete but used in env_emmc.c */
	#define CONFIG_ENV_IS_IN_MMC
	#define CONFIG_ENV_OFFSET 0x13F80000
	#define CONFIG_SYS_MMC_ENV_DEV 0 /* SLOT2: eMMC */

	/*
	* FLASH and environment organization
	*/
	#define CONFIG_SYS_NO_FLASH

	/*
	* base register values for U8500
	*/
	#define CFG_PRCMU_BASE 0x80157000 /* Power, reset and clock
	management unit */
	#define CFG_FSMC_BASE 0x80000000 /* FSMC Controller */

	#endif /* __CONFIG_H */