| /* |
| * Copyright 2007,2009 Wind River Systems <www.windriver.com> |
| * Copyright 2007 Embedded Specialties, Inc. |
| * Copyright 2004, 2007 Freescale Semiconductor. |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| /* |
| * sbc8548 board configuration file |
| * Please refer to doc/README.sbc8548 for more info. |
| */ |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| /* |
| * Top level Makefile configuration choices |
| */ |
| #ifdef CONFIG_PCI |
| #define CONFIG_PCI_INDIRECT_BRIDGE |
| #define CONFIG_PCI1 |
| #endif |
| |
| #ifdef CONFIG_66 |
| #define CONFIG_SYS_CLK_DIV 1 |
| #endif |
| |
| #ifdef CONFIG_33 |
| #define CONFIG_SYS_CLK_DIV 2 |
| #endif |
| |
| #ifdef CONFIG_PCIE |
| #define CONFIG_PCIE1 |
| #endif |
| |
| /* |
| * High Level Configuration Options |
| */ |
| #define CONFIG_BOOKE 1 /* BOOKE */ |
| #define CONFIG_E500 1 /* BOOKE e500 family */ |
| #define CONFIG_MPC85xx 1 /* MPC8540/60/55/41/48 */ |
| #define CONFIG_MPC8548 1 /* MPC8548 specific */ |
| #define CONFIG_SBC8548 1 /* SBC8548 board specific */ |
| |
| /* |
| * If you want to boot from the SODIMM flash, instead of the soldered |
| * on flash, set this, and change JP12, SW2:8 accordingly. |
| */ |
| #undef CONFIG_SYS_ALT_BOOT |
| |
| #ifndef CONFIG_SYS_TEXT_BASE |
| #ifdef CONFIG_SYS_ALT_BOOT |
| #define CONFIG_SYS_TEXT_BASE 0xfff00000 |
| #else |
| #define CONFIG_SYS_TEXT_BASE 0xfffa0000 |
| #endif |
| #endif |
| |
| #undef CONFIG_RIO |
| |
| #ifdef CONFIG_PCI |
| #define CONFIG_FSL_PCI_INIT /* Use common FSL init code */ |
| #define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ |
| #endif |
| #ifdef CONFIG_PCIE1 |
| #define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */ |
| #endif |
| |
| #define CONFIG_TSEC_ENET /* tsec ethernet support */ |
| #define CONFIG_ENV_OVERWRITE |
| |
| #define CONFIG_INTERRUPTS /* enable pci, srio, ddr interrupts */ |
| |
| #define CONFIG_FSL_LAW 1 /* Use common FSL init code */ |
| |
| /* |
| * Below assumes that CCB:SYSCLK remains unchanged at 6:1 via SW2:[1-4] |
| */ |
| #ifndef CONFIG_SYS_CLK_DIV |
| #define CONFIG_SYS_CLK_DIV 1 /* 2, if 33MHz PCI card installed */ |
| #endif |
| #define CONFIG_SYS_CLK_FREQ (66000000 / CONFIG_SYS_CLK_DIV) |
| |
| /* |
| * These can be toggled for performance analysis, otherwise use default. |
| */ |
| #define CONFIG_L2_CACHE /* toggle L2 cache */ |
| #define CONFIG_BTB /* toggle branch predition */ |
| |
| /* |
| * Only possible on E500 Version 2 or newer cores. |
| */ |
| #define CONFIG_ENABLE_36BIT_PHYS 1 |
| |
| #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ |
| |
| #undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */ |
| #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ |
| #define CONFIG_SYS_MEMTEST_END 0x00400000 |
| |
| #define CONFIG_SYS_CCSRBAR 0xe0000000 |
| #define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR |
| |
| /* DDR Setup */ |
| #define CONFIG_SYS_FSL_DDR2 |
| #undef CONFIG_FSL_DDR_INTERACTIVE |
| #undef CONFIG_DDR_ECC /* only for ECC DDR module */ |
| /* |
| * A hardware errata caused the LBC SDRAM SPD and the DDR2 SPD |
| * to collide, meaning you couldn't reliably read either. So |
| * physically remove the LBC PC100 SDRAM module from the board |
| * before enabling the two SPD options below, or check that you |
| * have the hardware fix on your board via "i2c probe" and looking |
| * for a device at 0x53. |
| */ |
| #undef CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ |
| #undef CONFIG_DDR_SPD |
| |
| #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */ |
| #define CONFIG_MEM_INIT_VALUE 0xDeadBeef |
| |
| #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 |
| #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE |
| #define CONFIG_VERY_BIG_RAM |
| |
| #define CONFIG_NUM_DDR_CONTROLLERS 1 |
| #define CONFIG_DIMM_SLOTS_PER_CTLR 1 |
| #define CONFIG_CHIP_SELECTS_PER_CTRL 2 |
| |
| /* |
| * The hardware fix for the I2C address collision puts the DDR |
| * SPD at 0x53, but if we are running on an older board w/o the |
| * fix, it will still be at 0x51. We check 0x53 1st. |
| */ |
| #define SPD_EEPROM_ADDRESS 0x51 /* CTLR 0 DIMM 0 */ |
| #define ALT_SPD_EEPROM_ADDRESS 0x53 /* CTLR 0 DIMM 0 */ |
| |
| /* |
| * Make sure required options are set |
| */ |
| #ifndef CONFIG_SPD_EEPROM |
| #define CONFIG_SYS_SDRAM_SIZE 256 /* DDR is 256MB */ |
| #define CONFIG_SYS_DDR_CONTROL 0xc300c000 |
| #endif |
| |
| #undef CONFIG_CLOCKS_IN_MHZ |
| |
| /* |
| * FLASH on the Local Bus |
| * Two banks, one 8MB the other 64MB, using the CFI driver. |
| * JP12+SW2.8 are used to swap CS0 and CS6, defaults are to have |
| * CS0 the 8MB boot flash, and CS6 the 64MB flash. |
| * |
| * Default: |
| * ec00_0000 efff_ffff 64MB SODIMM |
| * ff80_0000 ffff_ffff 8MB soldered flash |
| * |
| * Alternate: |
| * ef80_0000 efff_ffff 8MB soldered flash |
| * fc00_0000 ffff_ffff 64MB SODIMM |
| * |
| * BR0_8M: |
| * Base address 0 = 0xff80_0000 = BR0[0:16] = 1111 1111 1000 0000 0 |
| * Port Size = 8 bits = BRx[19:20] = 01 |
| * Use GPCM = BRx[24:26] = 000 |
| * Valid = BRx[31] = 1 |
| * |
| * BR0_64M: |
| * Base address 0 = 0xfc00_0000 = BR0[0:16] = 1111 1100 0000 0000 0 |
| * Port Size = 32 bits = BRx[19:20] = 11 |
| * |
| * 0 4 8 12 16 20 24 28 |
| * 1111 1111 1000 0000 0000 1000 0000 0001 = ff800801 BR0_8M |
| * 1111 1100 0000 0000 0001 1000 0000 0001 = fc001801 BR0_64M |
| */ |
| #define CONFIG_SYS_BR0_8M 0xff800801 |
| #define CONFIG_SYS_BR0_64M 0xfc001801 |
| |
| /* |
| * BR6_8M: |
| * Base address 6 = 0xef80_0000 = BR6[0:16] = 1110 1111 1000 0000 0 |
| * Port Size = 8 bits = BRx[19:20] = 01 |
| * Use GPCM = BRx[24:26] = 000 |
| * Valid = BRx[31] = 1 |
| |
| * BR6_64M: |
| * Base address 6 = 0xec00_0000 = BR6[0:16] = 1110 1100 0000 0000 0 |
| * Port Size = 32 bits = BRx[19:20] = 11 |
| * |
| * 0 4 8 12 16 20 24 28 |
| * 1110 1111 1000 0000 0000 1000 0000 0001 = ef800801 BR6_8M |
| * 1110 1100 0000 0000 0001 1000 0000 0001 = ec001801 BR6_64M |
| */ |
| #define CONFIG_SYS_BR6_8M 0xef800801 |
| #define CONFIG_SYS_BR6_64M 0xec001801 |
| |
| /* |
| * OR0_8M: |
| * Addr Mask = 8M = OR1[0:16] = 1111 1111 1000 0000 0 |
| * XAM = OR0[17:18] = 11 |
| * CSNT = OR0[20] = 1 |
| * ACS = half cycle delay = OR0[21:22] = 11 |
| * SCY = 6 = OR0[24:27] = 0110 |
| * TRLX = use relaxed timing = OR0[29] = 1 |
| * EAD = use external address latch delay = OR0[31] = 1 |
| * |
| * OR0_64M: |
| * Addr Mask = 64M = OR1[0:16] = 1111 1100 0000 0000 0 |
| * |
| * |
| * 0 4 8 12 16 20 24 28 |
| * 1111 1111 1000 0000 0110 1110 0110 0101 = ff806e65 OR0_8M |
| * 1111 1100 0000 0000 0110 1110 0110 0101 = fc006e65 OR0_64M |
| */ |
| #define CONFIG_SYS_OR0_8M 0xff806e65 |
| #define CONFIG_SYS_OR0_64M 0xfc006e65 |
| |
| /* |
| * OR6_8M: |
| * Addr Mask = 8M = OR6[0:16] = 1111 1111 1000 0000 0 |
| * XAM = OR6[17:18] = 11 |
| * CSNT = OR6[20] = 1 |
| * ACS = half cycle delay = OR6[21:22] = 11 |
| * SCY = 6 = OR6[24:27] = 0110 |
| * TRLX = use relaxed timing = OR6[29] = 1 |
| * EAD = use external address latch delay = OR6[31] = 1 |
| * |
| * OR6_64M: |
| * Addr Mask = 64M = OR6[0:16] = 1111 1100 0000 0000 0 |
| * |
| * 0 4 8 12 16 20 24 28 |
| * 1111 1111 1000 0000 0110 1110 0110 0101 = ff806e65 OR6_8M |
| * 1111 1100 0000 0000 0110 1110 0110 0101 = fc006e65 OR6_64M |
| */ |
| #define CONFIG_SYS_OR6_8M 0xff806e65 |
| #define CONFIG_SYS_OR6_64M 0xfc006e65 |
| |
| #ifndef CONFIG_SYS_ALT_BOOT /* JP12 in default position */ |
| #define CONFIG_SYS_BOOT_BLOCK 0xff800000 /* start of 8MB Flash */ |
| #define CONFIG_SYS_ALT_FLASH 0xec000000 /* 64MB "user" flash */ |
| |
| #define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_BR0_8M |
| #define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_OR0_8M |
| |
| #define CONFIG_SYS_BR6_PRELIM CONFIG_SYS_BR6_64M |
| #define CONFIG_SYS_OR6_PRELIM CONFIG_SYS_OR6_64M |
| #else /* JP12 in alternate position */ |
| #define CONFIG_SYS_BOOT_BLOCK 0xfc000000 /* start 64MB Flash */ |
| #define CONFIG_SYS_ALT_FLASH 0xef800000 /* 8MB soldered flash */ |
| |
| #define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_BR0_64M |
| #define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_OR0_64M |
| |
| #define CONFIG_SYS_BR6_PRELIM CONFIG_SYS_BR6_8M |
| #define CONFIG_SYS_OR6_PRELIM CONFIG_SYS_OR6_8M |
| #endif |
| |
| #define CONFIG_SYS_FLASH_BASE CONFIG_SYS_BOOT_BLOCK |
| #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE, \ |
| CONFIG_SYS_ALT_FLASH} |
| #define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ |
| #define CONFIG_SYS_MAX_FLASH_SECT 256 /* sectors per device */ |
| #undef CONFIG_SYS_FLASH_CHECKSUM |
| #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ |
| #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ |
| |
| #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ |
| |
| #define CONFIG_FLASH_CFI_DRIVER |
| #define CONFIG_SYS_FLASH_CFI |
| #define CONFIG_SYS_FLASH_EMPTY_INFO |
| |
| /* CS5 = Local bus peripherals controlled by the EPLD */ |
| |
| #define CONFIG_SYS_BR5_PRELIM 0xf8000801 |
| #define CONFIG_SYS_OR5_PRELIM 0xff006e65 |
| #define CONFIG_SYS_EPLD_BASE 0xf8000000 |
| #define CONFIG_SYS_LED_DISP_BASE 0xf8000000 |
| #define CONFIG_SYS_USER_SWITCHES_BASE 0xf8100000 |
| #define CONFIG_SYS_BD_REV 0xf8300000 |
| #define CONFIG_SYS_EEPROM_BASE 0xf8b00000 |
| |
| /* |
| * SDRAM on the Local Bus (CS3 and CS4) |
| * Note that most boards have a hardware errata where both the |
| * LBC SDRAM and the DDR2 SDRAM decode at 0x51, making it impossible |
| * to use CONFIG_DDR_SPD unless you physically remove the LBC DIMM. |
| * A hardware workaround is also available, see README.sbc8548 file. |
| */ |
| #define CONFIG_SYS_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */ |
| #define CONFIG_SYS_LBC_SDRAM_SIZE 128 /* LBC SDRAM is 128MB */ |
| |
| /* |
| * Base Register 3 and Option Register 3 configure the 1st 1/2 SDRAM. |
| * The SDRAM base address, CONFIG_SYS_LBC_SDRAM_BASE, is 0xf0000000. |
| * |
| * For BR3, need: |
| * Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0 |
| * port-size = 32-bits = BR2[19:20] = 11 |
| * no parity checking = BR2[21:22] = 00 |
| * SDRAM for MSEL = BR2[24:26] = 011 |
| * Valid = BR[31] = 1 |
| * |
| * 0 4 8 12 16 20 24 28 |
| * 1111 0000 0000 0000 0001 1000 0110 0001 = f0001861 |
| * |
| */ |
| |
| #define CONFIG_SYS_BR3_PRELIM 0xf0001861 |
| |
| /* |
| * The SDRAM size in MB, of 1/2 CONFIG_SYS_LBC_SDRAM_SIZE, is 64. |
| * |
| * For OR3, need: |
| * 64MB mask for AM, OR3[0:7] = 1111 1100 |
| * XAM, OR3[17:18] = 11 |
| * 10 columns OR3[19-21] = 011 |
| * 12 rows OR3[23-25] = 011 |
| * EAD set for extra time OR[31] = 0 |
| * |
| * 0 4 8 12 16 20 24 28 |
| * 1111 1100 0000 0000 0110 1100 1100 0000 = fc006cc0 |
| */ |
| |
| #define CONFIG_SYS_OR3_PRELIM 0xfc006cc0 |
| |
| /* |
| * Base Register 4 and Option Register 4 configure the 2nd 1/2 SDRAM. |
| * The base address, (SDRAM_BASE + 1/2*SIZE), is 0xf4000000. |
| * |
| * For BR4, need: |
| * Base address of 0xf4000000 = BR[0:16] = 1111 0100 0000 0000 0 |
| * port-size = 32-bits = BR2[19:20] = 11 |
| * no parity checking = BR2[21:22] = 00 |
| * SDRAM for MSEL = BR2[24:26] = 011 |
| * Valid = BR[31] = 1 |
| * |
| * 0 4 8 12 16 20 24 28 |
| * 1111 0000 0000 0000 0001 1000 0110 0001 = f4001861 |
| * |
| */ |
| |
| #define CONFIG_SYS_BR4_PRELIM 0xf4001861 |
| |
| /* |
| * The SDRAM size in MB, of 1/2 CONFIG_SYS_LBC_SDRAM_SIZE, is 64. |
| * |
| * For OR4, need: |
| * 64MB mask for AM, OR3[0:7] = 1111 1100 |
| * XAM, OR3[17:18] = 11 |
| * 10 columns OR3[19-21] = 011 |
| * 12 rows OR3[23-25] = 011 |
| * EAD set for extra time OR[31] = 0 |
| * |
| * 0 4 8 12 16 20 24 28 |
| * 1111 1100 0000 0000 0110 1100 1100 0000 = fc006cc0 |
| */ |
| |
| #define CONFIG_SYS_OR4_PRELIM 0xfc006cc0 |
| |
| #define CONFIG_SYS_LBC_LCRR 0x00000002 /* LB clock ratio reg */ |
| #define CONFIG_SYS_LBC_LBCR 0x00000000 /* LB config reg */ |
| #define CONFIG_SYS_LBC_LSRT 0x20000000 /* LB sdram refresh timer */ |
| #define CONFIG_SYS_LBC_MRTPR 0x00000000 /* LB refresh timer prescal*/ |
| |
| /* |
| * Common settings for all Local Bus SDRAM commands. |
| */ |
| #define CONFIG_SYS_LBC_LSDMR_COMMON ( LSDMR_RFCR16 \ |
| | LSDMR_BSMA1516 \ |
| | LSDMR_PRETOACT3 \ |
| | LSDMR_ACTTORW3 \ |
| | LSDMR_BUFCMD \ |
| | LSDMR_BL8 \ |
| | LSDMR_WRC2 \ |
| | LSDMR_CL3 \ |
| ) |
| |
| #define CONFIG_SYS_LBC_LSDMR_PCHALL \ |
| (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_PCHALL) |
| #define CONFIG_SYS_LBC_LSDMR_ARFRSH \ |
| (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_ARFRSH) |
| #define CONFIG_SYS_LBC_LSDMR_MRW \ |
| (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_MRW) |
| #define CONFIG_SYS_LBC_LSDMR_RFEN \ |
| (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_RFEN) |
| |
| #define CONFIG_SYS_INIT_RAM_LOCK 1 |
| #define CONFIG_SYS_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */ |
| #define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in RAM */ |
| |
| #define CONFIG_SYS_INIT_L2_ADDR 0xf8f80000 /* relocate boot L2SRAM */ |
| |
| #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) |
| #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET |
| |
| /* |
| * For soldered on flash, (128kB/sector) we use 2 sectors for u-boot and |
| * one for env+bootpg (CONFIG_SYS_TEXT_BASE=0xfffa_0000, 384kB total). For SODIMM |
| * flash (512kB/sector) we use 1 sector for u-boot, and one for env+bootpg |
| * (CONFIG_SYS_TEXT_BASE=0xfff0_0000, 1MB total). This dynamically sets the right |
| * thing for MONITOR_LEN in both cases. |
| */ |
| #define CONFIG_SYS_MONITOR_LEN (~CONFIG_SYS_TEXT_BASE + 1) |
| #define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */ |
| |
| /* Serial Port */ |
| #define CONFIG_CONS_INDEX 1 |
| #define CONFIG_SYS_NS16550 |
| #define CONFIG_SYS_NS16550_SERIAL |
| #define CONFIG_SYS_NS16550_REG_SIZE 1 |
| #define CONFIG_SYS_NS16550_CLK (400000000 / CONFIG_SYS_CLK_DIV) |
| |
| #define CONFIG_SYS_BAUDRATE_TABLE \ |
| {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} |
| |
| #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) |
| #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) |
| |
| /* Use the HUSH parser */ |
| #define CONFIG_SYS_HUSH_PARSER |
| |
| /* pass open firmware flat tree */ |
| #define CONFIG_OF_LIBFDT 1 |
| #define CONFIG_OF_BOARD_SETUP 1 |
| #define CONFIG_OF_STDOUT_VIA_ALIAS 1 |
| |
| /* |
| * I2C |
| */ |
| #define CONFIG_SYS_I2C |
| #define CONFIG_SYS_I2C_FSL |
| #define CONFIG_SYS_FSL_I2C_SPEED 400000 |
| #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F |
| #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 |
| #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 |
| |
| /* |
| * General PCI |
| * Memory space is mapped 1-1, but I/O space must start from 0. |
| */ |
| #define CONFIG_SYS_PCI_VIRT 0x80000000 /* 1G PCI TLB */ |
| #define CONFIG_SYS_PCI_PHYS 0x80000000 /* 1G PCI TLB */ |
| |
| #define CONFIG_SYS_PCI1_MEM_VIRT 0x80000000 |
| #define CONFIG_SYS_PCI1_MEM_BUS 0x80000000 |
| #define CONFIG_SYS_PCI1_MEM_PHYS 0x80000000 |
| #define CONFIG_SYS_PCI1_MEM_SIZE 0x20000000 /* 512M */ |
| #define CONFIG_SYS_PCI1_IO_VIRT 0xe2000000 |
| #define CONFIG_SYS_PCI1_IO_BUS 0x00000000 |
| #define CONFIG_SYS_PCI1_IO_PHYS 0xe2000000 |
| #define CONFIG_SYS_PCI1_IO_SIZE 0x00800000 /* 8M */ |
| |
| #ifdef CONFIG_PCIE1 |
| #define CONFIG_SYS_PCIE1_MEM_VIRT 0xa0000000 |
| #define CONFIG_SYS_PCIE1_MEM_BUS 0xa0000000 |
| #define CONFIG_SYS_PCIE1_MEM_PHYS 0xa0000000 |
| #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ |
| #define CONFIG_SYS_PCIE1_IO_VIRT 0xe2800000 |
| #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 |
| #define CONFIG_SYS_PCIE1_IO_PHYS 0xe2800000 |
| #define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 /* 8M */ |
| #endif |
| |
| #ifdef CONFIG_RIO |
| /* |
| * RapidIO MMU |
| */ |
| #define CONFIG_SYS_RIO_MEM_BASE 0xC0000000 |
| #define CONFIG_SYS_RIO_MEM_SIZE 0x20000000 /* 512M */ |
| #endif |
| |
| #if defined(CONFIG_PCI) |
| |
| #define CONFIG_PCI_PNP /* do pci plug-and-play */ |
| |
| #undef CONFIG_EEPRO100 |
| #undef CONFIG_TULIP |
| |
| #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ |
| |
| #endif /* CONFIG_PCI */ |
| |
| |
| #if defined(CONFIG_TSEC_ENET) |
| |
| #define CONFIG_MII 1 /* MII PHY management */ |
| #define CONFIG_TSEC1 1 |
| #define CONFIG_TSEC1_NAME "eTSEC0" |
| #define CONFIG_TSEC2 1 |
| #define CONFIG_TSEC2_NAME "eTSEC1" |
| #undef CONFIG_MPC85XX_FEC |
| |
| #define TSEC1_PHY_ADDR 0x19 |
| #define TSEC2_PHY_ADDR 0x1a |
| |
| #define TSEC1_PHYIDX 0 |
| #define TSEC2_PHYIDX 0 |
| |
| #define TSEC1_FLAGS TSEC_GIGABIT |
| #define TSEC2_FLAGS TSEC_GIGABIT |
| |
| /* Options are: eTSEC[0-3] */ |
| #define CONFIG_ETHPRIME "eTSEC0" |
| #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ |
| #endif /* CONFIG_TSEC_ENET */ |
| |
| /* |
| * Environment |
| */ |
| #define CONFIG_ENV_IS_IN_FLASH 1 |
| #define CONFIG_ENV_SIZE 0x2000 |
| #if CONFIG_SYS_TEXT_BASE == 0xfff00000 /* Boot from 64MB SODIMM */ |
| #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0x80000) |
| #define CONFIG_ENV_SECT_SIZE 0x80000 /* 512K(one sector) for env */ |
| #elif CONFIG_SYS_TEXT_BASE == 0xfffa0000 /* Boot from 8MB soldered flash */ |
| #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0x40000) |
| #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ |
| #else |
| #warning undefined environment size/location. |
| #endif |
| |
| #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ |
| #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ |
| |
| /* |
| * BOOTP options |
| */ |
| #define CONFIG_BOOTP_BOOTFILESIZE |
| #define CONFIG_BOOTP_BOOTPATH |
| #define CONFIG_BOOTP_GATEWAY |
| #define CONFIG_BOOTP_HOSTNAME |
| |
| |
| /* |
| * Command line configuration. |
| */ |
| #include <config_cmd_default.h> |
| |
| #define CONFIG_CMD_PING |
| #define CONFIG_CMD_I2C |
| #define CONFIG_CMD_MII |
| #define CONFIG_CMD_ELF |
| #define CONFIG_CMD_REGINFO |
| |
| #if defined(CONFIG_PCI) |
| #define CONFIG_CMD_PCI |
| #endif |
| |
| |
| #undef CONFIG_WATCHDOG /* watchdog disabled */ |
| |
| /* |
| * Miscellaneous configurable options |
| */ |
| #define CONFIG_CMDLINE_EDITING /* undef to save memory */ |
| #define CONFIG_AUTO_COMPLETE /* add autocompletion support */ |
| #define CONFIG_SYS_LONGHELP /* undef to save memory */ |
| #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ |
| #if defined(CONFIG_CMD_KGDB) |
| #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ |
| #else |
| #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ |
| #endif |
| #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ |
| #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ |
| #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ |
| |
| /* |
| * For booting Linux, the board info and command line data |
| * have to be in the first 8 MB of memory, since this is |
| * the maximum mapped by the Linux kernel during initialization. |
| */ |
| #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ |
| |
| #if defined(CONFIG_CMD_KGDB) |
| #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ |
| #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ |
| #endif |
| |
| /* |
| * Environment Configuration |
| */ |
| |
| /* The mac addresses for all ethernet interface */ |
| #if defined(CONFIG_TSEC_ENET) |
| #define CONFIG_HAS_ETH0 |
| #define CONFIG_ETHADDR 02:E0:0C:00:00:FD |
| #define CONFIG_HAS_ETH1 |
| #define CONFIG_ETH1ADDR 02:E0:0C:00:01:FD |
| #endif |
| |
| #define CONFIG_IPADDR 192.168.0.55 |
| |
| #define CONFIG_HOSTNAME sbc8548 |
| #define CONFIG_ROOTPATH "/opt/eldk/ppc_85xx" |
| #define CONFIG_BOOTFILE "/uImage" |
| #define CONFIG_UBOOTPATH /u-boot.bin /* TFTP server */ |
| |
| #define CONFIG_SERVERIP 192.168.0.2 |
| #define CONFIG_GATEWAYIP 192.168.0.1 |
| #define CONFIG_NETMASK 255.255.255.0 |
| |
| #define CONFIG_LOADADDR 1000000 /*default location for tftp and bootm*/ |
| |
| #define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ |
| #undef CONFIG_BOOTARGS /* the boot command will set bootargs*/ |
| |
| #define CONFIG_BAUDRATE 115200 |
| |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| "netdev=eth0\0" \ |
| "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ |
| "tftpflash=tftpboot $loadaddr $uboot; " \ |
| "protect off " __stringify(CONFIG_SYS_TEXT_BASE) " +$filesize; " \ |
| "erase " __stringify(CONFIG_SYS_TEXT_BASE) " +$filesize; " \ |
| "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) " $filesize; " \ |
| "protect on " __stringify(CONFIG_SYS_TEXT_BASE) " +$filesize; " \ |
| "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) " $filesize\0" \ |
| "consoledev=ttyS0\0" \ |
| "ramdiskaddr=2000000\0" \ |
| "ramdiskfile=uRamdisk\0" \ |
| "fdtaddr=c00000\0" \ |
| "fdtfile=sbc8548.dtb\0" |
| |
| #define CONFIG_NFSBOOTCOMMAND \ |
| "setenv bootargs root=/dev/nfs rw " \ |
| "nfsroot=$serverip:$rootpath " \ |
| "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ |
| "console=$consoledev,$baudrate $othbootargs;" \ |
| "tftp $loadaddr $bootfile;" \ |
| "tftp $fdtaddr $fdtfile;" \ |
| "bootm $loadaddr - $fdtaddr" |
| |
| |
| #define CONFIG_RAMBOOTCOMMAND \ |
| "setenv bootargs root=/dev/ram rw " \ |
| "console=$consoledev,$baudrate $othbootargs;" \ |
| "tftp $ramdiskaddr $ramdiskfile;" \ |
| "tftp $loadaddr $bootfile;" \ |
| "tftp $fdtaddr $fdtfile;" \ |
| "bootm $loadaddr $ramdiskaddr $fdtaddr" |
| |
| #define CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND |
| |
| #endif /* __CONFIG_H */ |