| /* |
| * (C) Copyright 2007-2008 |
| * Stelian Pop <stelian@popies.net> |
| * Lead Tech Design <www.leadtechdesign.com> |
| * Ilko Iliev <www.ronetix.at> |
| * |
| * Configuation settings for the RONETIX PM9261 board. |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| /* |
| * SoC must be defined first, before hardware.h is included. |
| * In this case SoC is defined in boards.cfg. |
| */ |
| |
| #include <asm/hardware.h> |
| /* ARM asynchronous clock */ |
| |
| #define CONFIG_DISPLAY_BOARDINFO |
| |
| #define MASTER_PLL_DIV 15 |
| #define MASTER_PLL_MUL 162 |
| #define MAIN_PLL_DIV 2 |
| #define CONFIG_SYS_AT91_SLOW_CLOCK 32768 /* slow clock xtal */ |
| #define CONFIG_SYS_AT91_MAIN_CLOCK 18432000 |
| |
| #define CONFIG_SYS_AT91_CPU_NAME "AT91SAM9261" |
| #define CONFIG_PM9261 1 /* on a Ronetix PM9261 Board */ |
| #define CONFIG_ARCH_CPU_INIT |
| #define CONFIG_SYS_TEXT_BASE 0 |
| |
| #define MACH_TYPE_PM9261 1187 |
| #define CONFIG_MACH_TYPE MACH_TYPE_PM9261 |
| |
| /* clocks */ |
| /* CKGR_MOR - enable main osc. */ |
| #define CONFIG_SYS_MOR_VAL \ |
| (AT91_PMC_MOR_MOSCEN | \ |
| (255 << 8)) /* Main Oscillator Start-up Time */ |
| #define CONFIG_SYS_PLLAR_VAL \ |
| (AT91_PMC_PLLAR_29 | /* Bit 29 must be 1 when prog */ \ |
| AT91_PMC_PLLXR_OUT(3) | \ |
| ((MASTER_PLL_MUL - 1) << 16) | (MASTER_PLL_DIV)) |
| |
| /* PCK/2 = MCK Master Clock from PLLA */ |
| #define CONFIG_SYS_MCKR1_VAL \ |
| (AT91_PMC_MCKR_CSS_SLOW | \ |
| AT91_PMC_MCKR_PRES_1 | \ |
| AT91_PMC_MCKR_MDIV_2) |
| |
| /* PCK/2 = MCK Master Clock from PLLA */ |
| #define CONFIG_SYS_MCKR2_VAL \ |
| (AT91_PMC_MCKR_CSS_PLLA | \ |
| AT91_PMC_MCKR_PRES_1 | \ |
| AT91_PMC_MCKR_MDIV_2) |
| |
| /* define PDC[31:16] as DATA[31:16] */ |
| #define CONFIG_SYS_PIOC_PDR_VAL1 0xFFFF0000 |
| /* no pull-up for D[31:16] */ |
| #define CONFIG_SYS_PIOC_PPUDR_VAL 0xFFFF0000 |
| |
| /* EBI_CSA, no pull-ups for D[15:0], CS1 SDRAM, CS3 NAND Flash */ |
| #define CONFIG_SYS_MATRIX_EBICSA_VAL \ |
| (AT91_MATRIX_CSA_DBPUC | AT91_MATRIX_CSA_EBI_CS1A) |
| |
| /* SDRAM */ |
| /* SDRAMC_MR Mode register */ |
| #define CONFIG_SYS_SDRC_MR_VAL1 AT91_SDRAMC_MODE_NORMAL |
| /* SDRAMC_TR - Refresh Timer register */ |
| #define CONFIG_SYS_SDRC_TR_VAL1 0x13C |
| /* SDRAMC_CR - Configuration register*/ |
| #define CONFIG_SYS_SDRC_CR_VAL \ |
| (AT91_SDRAMC_NC_9 | \ |
| AT91_SDRAMC_NR_13 | \ |
| AT91_SDRAMC_NB_4 | \ |
| AT91_SDRAMC_CAS_3 | \ |
| AT91_SDRAMC_DBW_32 | \ |
| (1 << 8) | /* Write Recovery Delay */ \ |
| (7 << 12) | /* Row Cycle Delay */ \ |
| (3 << 16) | /* Row Precharge Delay */ \ |
| (2 << 20) | /* Row to Column Delay */ \ |
| (5 << 24) | /* Active to Precharge Delay */ \ |
| (1 << 28)) /* Exit Self Refresh to Active Delay */ |
| |
| /* Memory Device Register -> SDRAM */ |
| #define CONFIG_SYS_SDRC_MDR_VAL AT91_SDRAMC_MD_SDRAM |
| #define CONFIG_SYS_SDRC_MR_VAL2 AT91_SDRAMC_MODE_PRECHARGE |
| #define CONFIG_SYS_SDRAM_VAL1 0 /* SDRAM_BASE */ |
| #define CONFIG_SYS_SDRC_MR_VAL3 AT91_SDRAMC_MODE_REFRESH |
| #define CONFIG_SYS_SDRAM_VAL2 0 /* SDRAM_BASE */ |
| #define CONFIG_SYS_SDRAM_VAL3 0 /* SDRAM_BASE */ |
| #define CONFIG_SYS_SDRAM_VAL4 0 /* SDRAM_BASE */ |
| #define CONFIG_SYS_SDRAM_VAL5 0 /* SDRAM_BASE */ |
| #define CONFIG_SYS_SDRAM_VAL6 0 /* SDRAM_BASE */ |
| #define CONFIG_SYS_SDRAM_VAL7 0 /* SDRAM_BASE */ |
| #define CONFIG_SYS_SDRAM_VAL8 0 /* SDRAM_BASE */ |
| #define CONFIG_SYS_SDRAM_VAL9 0 /* SDRAM_BASE */ |
| #define CONFIG_SYS_SDRC_MR_VAL4 AT91_SDRAMC_MODE_LMR |
| #define CONFIG_SYS_SDRAM_VAL10 0 /* SDRAM_BASE */ |
| #define CONFIG_SYS_SDRC_MR_VAL5 AT91_SDRAMC_MODE_NORMAL |
| #define CONFIG_SYS_SDRAM_VAL11 0 /* SDRAM_BASE */ |
| #define CONFIG_SYS_SDRC_TR_VAL2 1200 /* SDRAM_TR */ |
| #define CONFIG_SYS_SDRAM_VAL12 0 /* SDRAM_BASE */ |
| |
| /* setup SMC0, CS0 (NOR Flash) - 16-bit, 15 WS */ |
| #define CONFIG_SYS_SMC0_SETUP0_VAL \ |
| (AT91_SMC_SETUP_NWE(10) | AT91_SMC_SETUP_NCS_WR(10) | \ |
| AT91_SMC_SETUP_NRD(10) | AT91_SMC_SETUP_NCS_RD(10)) |
| #define CONFIG_SYS_SMC0_PULSE0_VAL \ |
| (AT91_SMC_PULSE_NWE(11) | AT91_SMC_PULSE_NCS_WR(11) | \ |
| AT91_SMC_PULSE_NRD(11) | AT91_SMC_PULSE_NCS_RD(11)) |
| #define CONFIG_SYS_SMC0_CYCLE0_VAL \ |
| (AT91_SMC_CYCLE_NWE(22) | AT91_SMC_CYCLE_NRD(22)) |
| #define CONFIG_SYS_SMC0_MODE0_VAL \ |
| (AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE | \ |
| AT91_SMC_MODE_DBW_16 | \ |
| AT91_SMC_MODE_TDF | \ |
| AT91_SMC_MODE_TDF_CYCLE(6)) |
| |
| /* user reset enable */ |
| #define CONFIG_SYS_RSTC_RMR_VAL \ |
| (AT91_RSTC_KEY | \ |
| AT91_RSTC_CR_PROCRST | \ |
| AT91_RSTC_MR_ERSTL(1) | \ |
| AT91_RSTC_MR_ERSTL(2)) |
| |
| /* Disable Watchdog */ |
| #define CONFIG_SYS_WDTC_WDMR_VAL \ |
| (AT91_WDT_MR_WDIDLEHLT | AT91_WDT_MR_WDDBGHLT | \ |
| AT91_WDT_MR_WDV(0xfff) | \ |
| AT91_WDT_MR_WDDIS | \ |
| AT91_WDT_MR_WDD(0xfff)) |
| |
| #define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ |
| #define CONFIG_SETUP_MEMORY_TAGS 1 |
| #define CONFIG_INITRD_TAG 1 |
| |
| #undef CONFIG_SKIP_LOWLEVEL_INIT |
| #define CONFIG_BOARD_EARLY_INIT_F |
| |
| /* |
| * Hardware drivers |
| */ |
| #define CONFIG_AT91_GPIO 1 |
| #define CONFIG_ATMEL_USART 1 |
| #define CONFIG_USART_BASE ATMEL_BASE_DBGU |
| #define CONFIG_USART_ID ATMEL_ID_SYS |
| |
| /* LCD */ |
| #define CONFIG_LCD 1 |
| #define LCD_BPP LCD_COLOR8 |
| #define CONFIG_LCD_LOGO 1 |
| #undef LCD_TEST_PATTERN |
| #define CONFIG_LCD_INFO 1 |
| #define CONFIG_LCD_INFO_BELOW_LOGO 1 |
| #define CONFIG_SYS_WHITE_ON_BLACK 1 |
| #define CONFIG_ATMEL_LCD 1 |
| #define CONFIG_ATMEL_LCD_BGR555 1 |
| #define CONFIG_SYS_CONSOLE_IS_IN_ENV 1 |
| |
| /* LED */ |
| #define CONFIG_AT91_LED |
| #define CONFIG_RED_LED GPIO_PIN_PC(12) |
| #define CONFIG_GREEN_LED GPIO_PIN_PC(13) |
| #define CONFIG_YELLOW_LED GPIO_PIN_PC(15) |
| |
| #define CONFIG_BOOTDELAY 3 |
| |
| /* |
| * BOOTP options |
| */ |
| #define CONFIG_BOOTP_BOOTFILESIZE 1 |
| #define CONFIG_BOOTP_BOOTPATH 1 |
| #define CONFIG_BOOTP_GATEWAY 1 |
| #define CONFIG_BOOTP_HOSTNAME 1 |
| |
| /* |
| * Command line configuration. |
| */ |
| #include <config_cmd_default.h> |
| #undef CONFIG_CMD_BDI |
| #undef CONFIG_CMD_IMI |
| #undef CONFIG_CMD_FPGA |
| #undef CONFIG_CMD_LOADS |
| #undef CONFIG_CMD_IMLS |
| |
| #define CONFIG_CMD_CACHE |
| #define CONFIG_CMD_PING 1 |
| #define CONFIG_CMD_DHCP 1 |
| #define CONFIG_CMD_NAND 1 |
| #define CONFIG_CMD_USB 1 |
| |
| /* SDRAM */ |
| #define CONFIG_NR_DRAM_BANKS 1 |
| #define PHYS_SDRAM 0x20000000 |
| #define PHYS_SDRAM_SIZE 0x04000000 /* 64 megs */ |
| |
| /* DataFlash */ |
| #define CONFIG_ATMEL_DATAFLASH_SPI |
| #define CONFIG_HAS_DATAFLASH |
| #define CONFIG_SYS_SPI_WRITE_TOUT (5 * CONFIG_SYS_HZ) |
| #define CONFIG_SYS_MAX_DATAFLASH_BANKS 1 |
| #define CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0 0xC0000000 /* CS0 */ |
| #define CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS3 0xD0000000 /* CS3 */ |
| #define AT91_SPI_CLK 15000000 |
| #define DATAFLASH_TCSS (0x1a << 16) |
| #define DATAFLASH_TCHS (0x1 << 24) |
| |
| /* NAND flash */ |
| #define CONFIG_NAND_ATMEL |
| #define CONFIG_SYS_MAX_NAND_DEVICE 1 |
| #define CONFIG_SYS_NAND_BASE 0x40000000 |
| #define CONFIG_SYS_NAND_DBW_8 1 |
| /* our ALE is AD22 */ |
| #define CONFIG_SYS_NAND_MASK_ALE (1 << 22) |
| /* our CLE is AD21 */ |
| #define CONFIG_SYS_NAND_MASK_CLE (1 << 21) |
| #define CONFIG_SYS_NAND_ENABLE_PIN GPIO_PIN_PC(14) |
| #define CONFIG_SYS_NAND_READY_PIN GPIO_PIN_PA(16) |
| |
| /* NOR flash */ |
| #define CONFIG_SYS_FLASH_CFI 1 |
| #define CONFIG_FLASH_CFI_DRIVER 1 |
| #define PHYS_FLASH_1 0x10000000 |
| #define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1 |
| #define CONFIG_SYS_MAX_FLASH_SECT 256 |
| #define CONFIG_SYS_MAX_FLASH_BANKS 1 |
| |
| /* Ethernet */ |
| #define CONFIG_DRIVER_DM9000 1 |
| #define CONFIG_DM9000_BASE 0x30000000 |
| #define DM9000_IO CONFIG_DM9000_BASE |
| #define DM9000_DATA (CONFIG_DM9000_BASE + 4) |
| #define CONFIG_DM9000_USE_16BIT 1 |
| #define CONFIG_NET_RETRY_COUNT 20 |
| #define CONFIG_RESET_PHY_R 1 |
| |
| /* USB */ |
| #define CONFIG_USB_ATMEL |
| #define CONFIG_USB_ATMEL_CLK_SEL_PLLB |
| #define CONFIG_USB_OHCI_NEW 1 |
| #define CONFIG_DOS_PARTITION 1 |
| #define CONFIG_SYS_USB_OHCI_CPU_INIT 1 |
| #define CONFIG_SYS_USB_OHCI_REGS_BASE 0x00500000 |
| #define CONFIG_SYS_USB_OHCI_SLOT_NAME "at91sam9261" |
| #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 2 |
| #define CONFIG_USB_STORAGE 1 |
| |
| #define CONFIG_SYS_LOAD_ADDR 0x22000000 |
| |
| #define CONFIG_SYS_MEMTEST_START PHYS_SDRAM |
| #define CONFIG_SYS_MEMTEST_END 0x23e00000 |
| |
| #undef CONFIG_SYS_USE_DATAFLASH_CS0 |
| #undef CONFIG_SYS_USE_NANDFLASH |
| #define CONFIG_SYS_USE_FLASH 1 |
| |
| #ifdef CONFIG_SYS_USE_DATAFLASH_CS0 |
| |
| /* bootstrap + u-boot + env + linux in dataflash on CS0 */ |
| #define CONFIG_ENV_IS_IN_DATAFLASH 1 |
| #define CONFIG_SYS_MONITOR_BASE \ |
| (CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0 + 0x8400) |
| #define CONFIG_ENV_OFFSET 0x4200 |
| #define CONFIG_ENV_ADDR \ |
| (CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0 + CONFIG_ENV_OFFSET) |
| #define CONFIG_ENV_SIZE 0x4200 |
| #define CONFIG_BOOTCOMMAND "cp.b 0xC0042000 0x22000000 0x210000; bootm" |
| #define CONFIG_BOOTARGS "console=ttyS0,115200 " \ |
| "root=/dev/mtdblock0 " \ |
| "mtdparts=atmel_nand:-(root) " \ |
| "rw rootfstype=jffs2" |
| |
| #elif defined(CONFIG_SYS_USE_NANDFLASH) /* CONFIG_SYS_USE_NANDFLASH */ |
| |
| /* bootstrap + u-boot + env + linux in nandflash */ |
| #define CONFIG_ENV_IS_IN_NAND 1 |
| #define CONFIG_ENV_OFFSET 0x60000 |
| #define CONFIG_ENV_OFFSET_REDUND 0x80000 |
| #define CONFIG_ENV_SIZE 0x20000 /* 1 sector = 128 kB */ |
| #define CONFIG_BOOTCOMMAND "nand read 0x22000000 0xA0000 0x200000; bootm" |
| #define CONFIG_BOOTARGS "console=ttyS0,115200 " \ |
| "root=/dev/mtdblock5 " \ |
| "mtdparts=atmel_nand:128k(bootstrap)ro," \ |
| "256k(uboot)ro,128k(env1)ro," \ |
| "128k(env2)ro,2M(linux),-(root) " \ |
| "rw rootfstype=jffs2" |
| |
| #elif defined (CONFIG_SYS_USE_FLASH) |
| |
| #define CONFIG_ENV_IS_IN_FLASH 1 |
| #define CONFIG_ENV_OFFSET 0x40000 |
| #define CONFIG_ENV_SECT_SIZE 0x10000 |
| #define CONFIG_ENV_SIZE 0x10000 |
| #define CONFIG_ENV_OVERWRITE 1 |
| |
| /* JFFS Partition offset set */ |
| #define CONFIG_SYS_JFFS2_FIRST_BANK 0 |
| #define CONFIG_SYS_JFFS2_NUM_BANKS 1 |
| |
| /* 512k reserved for u-boot */ |
| #define CONFIG_SYS_JFFS2_FIRST_SECTOR 11 |
| |
| #define CONFIG_BOOTCOMMAND "run flashboot" |
| |
| #define MTDIDS_DEFAULT "nor0=physmap-flash.0,nand0=nand" |
| #define MTDPARTS_DEFAULT \ |
| "mtdparts=physmap-flash.0:" \ |
| "256k(u-boot)ro," \ |
| "64k(u-boot-env)ro," \ |
| "1408k(kernel)," \ |
| "-(rootfs);" \ |
| "nand:-(nand)" |
| |
| #define CONFIG_CON_ROT "fbcon=rotate:3 " |
| #define CONFIG_BOOTARGS "root=/dev/mtdblock4 rootfstype=jffs2 " CONFIG_CON_ROT |
| |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| "mtdids=" MTDIDS_DEFAULT "\0" \ |
| "mtdparts=" MTDPARTS_DEFAULT "\0" \ |
| "partition=nand0,0\0" \ |
| "ramargs=setenv bootargs $(bootargs) $(mtdparts)\0" \ |
| "nfsargs=setenv bootargs root=/dev/nfs rw " \ |
| CONFIG_CON_ROT \ |
| "nfsroot=$(serverip):$(rootpath) $(mtdparts)\0" \ |
| "addip=setenv bootargs $(bootargs) " \ |
| "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)"\ |
| ":$(hostname):eth0:off\0" \ |
| "ramboot=tftpboot 0x22000000 vmImage;" \ |
| "run ramargs;run addip;bootm 22000000\0" \ |
| "nfsboot=tftpboot 0x22000000 vmImage;" \ |
| "run nfsargs;run addip;bootm 22000000\0" \ |
| "flashboot=run ramargs;run addip;bootm 0x10050000\0" \ |
| "" |
| #else |
| #error "Undefined memory device" |
| #endif |
| |
| #define CONFIG_BAUDRATE 115200 |
| |
| #define CONFIG_SYS_PROMPT "pm9261> " |
| #define CONFIG_SYS_CBSIZE 256 |
| #define CONFIG_SYS_MAXARGS 16 |
| #define CONFIG_SYS_PBSIZE \ |
| (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) |
| #define CONFIG_SYS_LONGHELP 1 |
| #define CONFIG_CMDLINE_EDITING 1 |
| |
| /* |
| * Size of malloc() pool |
| */ |
| #define CONFIG_SYS_MALLOC_LEN \ |
| ROUND(3 * CONFIG_ENV_SIZE + 128 * 1024, 0x1000) |
| |
| #define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM |
| #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + 0x1000 - \ |
| GENERATED_GBL_DATA_SIZE) |
| |
| #endif |