| /* |
| * (C) Copyright 2001 |
| * Josh Huber <huber@mclx.com>, Mission Critical Linux, Inc. |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| /* |
| * board/config.h - configuration options, board specific |
| */ |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| #define CONFIG_SYS_GT_6426x GT_64260 /* with a 64260 system controller */ |
| #define CONFIG_ETHER_PORT_MII /* use two MII ports */ |
| #define CONFIG_INTEL_LXT97X /* Intel LXT97X phy */ |
| |
| #ifndef __ASSEMBLY__ |
| #include <galileo/core.h> |
| #endif |
| |
| #include "../board/evb64260/local.h" |
| |
| #define CONFIG_EVB64260 1 /* this is an EVB64260 board */ |
| #define CONFIG_ZUMA_V2 1 /* always define this for ZUMA v2 */ |
| |
| #define CONFIG_SYS_TEXT_BASE 0xfff00000 |
| |
| /* #define CONFIG_ZUMA_V2_OLD 1 */ /* backwards compat for old V2 board */ |
| |
| #define CONFIG_BAUDRATE 38400 /* console baudrate = 38400 */ |
| |
| #define CONFIG_ECC /* enable ECC support */ |
| |
| #define CONFIG_750CX /* we have a 750CX/CXe (override local.h) */ |
| |
| /* which initialization functions to call for this board */ |
| #define CONFIG_MISC_INIT_R |
| #define CONFIG_BOARD_EARLY_INIT_F |
| #define CONFIG_SYS_BOARD_ASM_INIT |
| |
| #define CONFIG_SYS_BOARD_NAME "Zuma APv2" |
| |
| #define CONFIG_SYS_HUSH_PARSER |
| |
| /* |
| * The following defines let you select what serial you want to use |
| * for your console driver. |
| * |
| * what to do: |
| * to use the DUART, undef CONFIG_MPSC. If you have hacked a serial |
| * cable onto the second DUART channel, change the CONFIG_SYS_DUART port from 1 |
| * to 0 below. |
| * |
| * to use the MPSC, #define CONFIG_MPSC. If you have wired up another |
| * mpsc channel, change CONFIG_MPSC_PORT to the desired value. |
| */ |
| #define CONFIG_MPSC |
| |
| #define CONFIG_MPSC_PORT 0 |
| |
| |
| /* define this if you want to enable GT MAC filtering */ |
| #define CONFIG_GT_USE_MAC_HASH_TABLE |
| |
| #if 1 |
| #define CONFIG_BOOTDELAY -1 /* autoboot disabled */ |
| #else |
| #define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ |
| #endif |
| #define CONFIG_ZERO_BOOTDELAY_CHECK |
| |
| #undef CONFIG_BOOTARGS |
| |
| #define CONFIG_BOOTCOMMAND \ |
| "tftpboot && " \ |
| "setenv bootargs root=/dev/nfs rw nfsroot=$serverip:$rootpath " \ |
| "ip=$ipaddr:$serverip:$gatewayip:" \ |
| "$netmask:$hostname:eth0:none panic=5 && bootm" |
| |
| #define CONFIG_LOADS_ECHO 0 /* echo off for serial download */ |
| #define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate changes */ |
| |
| #undef CONFIG_WATCHDOG /* watchdog disabled */ |
| #undef CONFIG_ALTIVEC /* undef to disable */ |
| |
| /* |
| * BOOTP options |
| */ |
| #define CONFIG_BOOTP_SUBNETMASK |
| #define CONFIG_BOOTP_GATEWAY |
| #define CONFIG_BOOTP_HOSTNAME |
| #define CONFIG_BOOTP_BOOTPATH |
| #define CONFIG_BOOTP_BOOTFILESIZE |
| |
| #define CONFIG_MII /* enable MII commands */ |
| |
| |
| /* |
| * Command line configuration. |
| */ |
| #include <config_cmd_default.h> |
| |
| #define CONFIG_CMD_ASKENV |
| #define CONFIG_CMD_BSP |
| #define CONFIG_CMD_JFFS2 |
| #define CONFIG_CMD_MII |
| #define CONFIG_CMD_DATE |
| |
| |
| /* |
| * JFFS2 partitions |
| * |
| */ |
| /* No command line, one static partition, whole device */ |
| #undef CONFIG_CMD_MTDPARTS |
| #define CONFIG_JFFS2_DEV "nor0" |
| #define CONFIG_JFFS2_PART_SIZE 0xFFFFFFFF |
| #define CONFIG_JFFS2_PART_OFFSET 0x00000000 |
| |
| /* mtdparts command line support */ |
| /* Note: fake mtd_id used, no linux mtd map file */ |
| /* |
| #define CONFIG_CMD_MTDPARTS |
| #define MTDIDS_DEFAULT "nor1=zuma-1,nor2=zuma-2" |
| #define MTDPARTS_DEFAULT "mtdparts=zuma-1:-(jffs2),zuma-2:-(user)" |
| */ |
| |
| /* |
| * Miscellaneous configurable options |
| */ |
| #define CONFIG_SYS_LONGHELP /* undef to save memory */ |
| #if defined(CONFIG_CMD_KGDB) |
| #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ |
| #else |
| #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ |
| #endif |
| #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ |
| #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ |
| #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ |
| |
| #define CONFIG_SYS_MEMTEST_START 0x00400000 /* memtest works on */ |
| #define CONFIG_SYS_MEMTEST_END 0x00C00000 /* 4 ... 12 MB in DRAM */ |
| |
| #define CONFIG_SYS_LOAD_ADDR 0x00300000 /* default load address */ |
| |
| #define CONFIG_SYS_BUS_CLK 133000000 /* 133 MHz */ |
| |
| #define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } |
| |
| /* |
| * Low Level Configuration Settings |
| * (address mappings, register initial values, etc.) |
| * You should know what you are doing if you make changes here. |
| */ |
| |
| /*----------------------------------------------------------------------- |
| * Definitions for initial stack pointer and data area |
| */ |
| #define CONFIG_SYS_INIT_RAM_ADDR 0x40000000 |
| #define CONFIG_SYS_INIT_RAM_SIZE 0x1000 |
| #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) |
| #define CONFIG_SYS_INIT_RAM_LOCK |
| |
| |
| /*----------------------------------------------------------------------- |
| * Start addresses for the final memory configuration |
| * (Set up by the startup code) |
| * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 |
| */ |
| #define CONFIG_SYS_SDRAM_BASE 0x00000000 |
| #define CONFIG_SYS_FLASH_BASE 0xfff00000 |
| #define CONFIG_SYS_RESET_ADDRESS 0xfff00100 |
| #define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ |
| #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE |
| #define CONFIG_SYS_MALLOC_LEN (256 << 10) /* Reserve 256 kB for malloc */ |
| |
| /* areas to map different things with the GT in physical space */ |
| #define CONFIG_SYS_DRAM_BANKS 4 |
| #define CONFIG_SYS_DFL_GT_REGS 0x14000000 /* boot time GT_REGS */ |
| |
| /* What to put in the bats. */ |
| #define CONFIG_SYS_MISC_REGION_BASE 0xf0000000 |
| |
| /* Peripheral Device section */ |
| #define CONFIG_SYS_GT_REGS 0xf8000000 /* later mapped GT_REGS */ |
| #define CONFIG_SYS_DEV_BASE 0xf0000000 |
| #define CONFIG_SYS_DEV0_SIZE _64M /* zuma flash @ 0xf000.0000*/ |
| #define CONFIG_SYS_DEV1_SIZE _8M /* zuma IDE @ 0xf400.0000 */ |
| #define CONFIG_SYS_DEV2_SIZE _8M /* unused */ |
| #define CONFIG_SYS_DEV3_SIZE _8M /* unused */ |
| |
| #define CONFIG_SYS_DEV0_PAR 0xc498243c |
| /* c 4 9 8 2 4 3 c */ |
| /* 33 22|2222|22 22|111 1|11 11|1 1 | | */ |
| /* 10 98|7654|32 10|987 6|54 32|1 098|7 654|3 210 */ |
| /* 11|00|0100|10 01|100|0 00|10 0|100 0|011 1|100 */ |
| /* 3| 0|.... ..| 1| 4 | 0 | 4 | 8 | 7 | 4 */ |
| |
| #define CONFIG_SYS_DEV1_PAR 0xc01b6ac5 |
| /* c 0 1 b 6 a c 5 */ |
| /* 33 22|2222|22 22|111 1|11 11|1 1 | | */ |
| /* 10 98|7654|32 10|987 6|54 32|1 098|7 654|3 210 */ |
| /* 11|00|0000|00 01|101|1 01|10 1|010 1|100 0|101 */ |
| /* 3| 0|.... ..| 1| 5 | 5 | 5 | 5 | 8 | 5 */ |
| |
| |
| #define CONFIG_SYS_8BIT_BOOT_PAR 0xc00b5e7c |
| |
| #define CONFIG_SYS_MPP_CONTROL_0 0x00007777 /* GPP[7:4] : REQ0[1:0] GNT0[1:0] */ |
| #define CONFIG_SYS_MPP_CONTROL_1 0x00000000 /* GPP[15:12] : GPP[11:8] */ |
| #define CONFIG_SYS_MPP_CONTROL_2 0x00008888 /* GPP[23:20] : REQ1[1:0] GNT1[1:0] */ |
| #define CONFIG_SYS_MPP_CONTROL_3 0x00000000 /* GPP[31:28] (int[3:0]) */ |
| /* GPP[27:24] (27 is int4, rest are GPP) */ |
| |
| #define CONFIG_SYS_SERIAL_PORT_MUX 0x00001101 /* 11=MPSC1/MPSC0 01=ETH, 0=only MII */ |
| #define CONFIG_SYS_GPP_LEVEL_CONTROL 0xf8000000 /* interrupt inputs: GPP[31:27] */ |
| |
| #define CONFIG_SYS_SDRAM_CONFIG 0xe4e18200 /* 0x448 */ |
| /* idmas use buffer 1,1 |
| comm use buffer 1 |
| pci use buffer 0,0 (pci1->0 pci0->0) |
| cpu use buffer 1 (R*18) |
| normal load (see also ifdef HVL) |
| standard SDRAM (see also ifdef REG) |
| non staggered refresh */ |
| /* 31:26 25 23 20 19 18 16 */ |
| /* 111001 00 111 0 0 00 1 */ |
| |
| /* refresh count=0x200 |
| phy interleave disable (by default, |
| set later by dram config..) |
| virt interleave enable */ |
| /* 15 14 13:0 */ |
| /* 1 0 0x200 */ |
| |
| #define CONFIG_SYS_DEV0_SPACE CONFIG_SYS_DEV_BASE |
| #define CONFIG_SYS_DEV1_SPACE (CONFIG_SYS_DEV0_SPACE + CONFIG_SYS_DEV0_SIZE) |
| #define CONFIG_SYS_DEV2_SPACE (CONFIG_SYS_DEV1_SPACE + CONFIG_SYS_DEV1_SIZE) |
| #define CONFIG_SYS_DEV3_SPACE (CONFIG_SYS_DEV2_SPACE + CONFIG_SYS_DEV2_SIZE) |
| |
| /*----------------------------------------------------------------------- |
| * PCI stuff |
| */ |
| |
| #define PCI_HOST_ADAPTER 0 /* configure ar pci adapter */ |
| #define PCI_HOST_FORCE 1 /* configure as pci host */ |
| #define PCI_HOST_AUTO 2 /* detected via arbiter enable */ |
| |
| #define CONFIG_PCI /* include pci support */ |
| #define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */ |
| #define CONFIG_PCI_PNP /* do pci plug-and-play */ |
| |
| /* PCI MEMORY MAP section */ |
| #define CONFIG_SYS_PCI0_MEM_BASE 0x80000000 |
| #define CONFIG_SYS_PCI0_MEM_SIZE _128M |
| #define CONFIG_SYS_PCI1_MEM_BASE 0x88000000 |
| #define CONFIG_SYS_PCI1_MEM_SIZE _128M |
| |
| #define CONFIG_SYS_PCI0_0_MEM_SPACE (CONFIG_SYS_PCI0_MEM_BASE) |
| #define CONFIG_SYS_PCI1_0_MEM_SPACE (CONFIG_SYS_PCI1_MEM_BASE) |
| |
| /* PCI I/O MAP section */ |
| #define CONFIG_SYS_PCI0_IO_BASE 0xfa000000 |
| #define CONFIG_SYS_PCI0_IO_SIZE _16M |
| #define CONFIG_SYS_PCI1_IO_BASE 0xfb000000 |
| #define CONFIG_SYS_PCI1_IO_SIZE _16M |
| |
| #define CONFIG_SYS_PCI0_IO_SPACE (CONFIG_SYS_PCI0_IO_BASE) |
| #define CONFIG_SYS_PCI0_IO_SPACE_PCI 0x00000000 |
| #define CONFIG_SYS_PCI1_IO_SPACE (CONFIG_SYS_PCI1_IO_BASE) |
| #define CONFIG_SYS_PCI1_IO_SPACE_PCI 0x00000000 |
| |
| |
| /*---------------------------------------------------------------------- |
| * Initial BAT mappings |
| */ |
| |
| /* NOTES: |
| * 1) GUARDED and WRITE_THRU not allowed in IBATS |
| * 2) CACHEINHIBIT and WRITETHROUGH not allowed together in same BAT |
| */ |
| |
| /* SDRAM */ |
| #define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_RW | BATL_CACHEINHIBIT) |
| #define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) |
| #define CONFIG_SYS_DBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) |
| #define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U |
| |
| /* init ram */ |
| #define CONFIG_SYS_IBAT1L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE) |
| #define CONFIG_SYS_IBAT1U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP) |
| #define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L |
| #define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U |
| |
| /* PCI0, PCI1 memory space (starting at PCI0 base, mapped in one BAT) */ |
| #define CONFIG_SYS_IBAT2L BATL_NO_ACCESS |
| #define CONFIG_SYS_IBAT2U CONFIG_SYS_DBAT2U |
| #define CONFIG_SYS_DBAT2L (CONFIG_SYS_PCI0_MEM_BASE | BATL_CACHEINHIBIT | BATL_PP_RW | BATL_GUARDEDSTORAGE) |
| #define CONFIG_SYS_DBAT2U (CONFIG_SYS_PCI0_MEM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) |
| |
| /* GT regs, bootrom, all the devices, PCI I/O */ |
| #define CONFIG_SYS_IBAT3L (CONFIG_SYS_MISC_REGION_BASE | BATL_CACHEINHIBIT | BATL_PP_RW) |
| #define CONFIG_SYS_IBAT3U (CONFIG_SYS_MISC_REGION_BASE | BATU_VS | BATU_VP | BATU_BL_256M) |
| #define CONFIG_SYS_DBAT3L (CONFIG_SYS_MISC_REGION_BASE | BATL_CACHEINHIBIT | BATL_PP_RW | BATL_GUARDEDSTORAGE) |
| #define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U |
| |
| /* |
| * For booting Linux, the board info and command line data |
| * have to be in the first 8 MB of memory, since this is |
| * the maximum mapped by the Linux kernel during initialization. |
| */ |
| #define CONFIG_SYS_BOOTMAPSZ (8<<20) /* Initial Memory map for Linux */ |
| |
| |
| /*----------------------------------------------------------------------- |
| * FLASH organization |
| */ |
| #define CONFIG_SYS_MAX_FLASH_BANKS 3 /* max number of memory banks */ |
| #define CONFIG_SYS_MAX_FLASH_SECT 130 /* max number of sectors on one chip */ |
| |
| #define CONFIG_SYS_EXTRA_FLASH_DEVICE DEVICE0 /* extra flash at device 0 */ |
| #define CONFIG_SYS_EXTRA_FLASH_WIDTH 2 /* 16 bit */ |
| |
| #define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ |
| #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ |
| #define CONFIG_SYS_FLASH_CFI 1 |
| |
| #define CONFIG_ENV_IS_IN_FLASH 1 |
| #define CONFIG_ENV_SIZE 0x1000 /* Total Size of Environment Sector */ |
| #define CONFIG_ENV_SECT_SIZE 0x10000 /* see README - env sect real size */ |
| #define CONFIG_ENV_ADDR (0xfff80000 - CONFIG_ENV_SECT_SIZE) |
| |
| /*----------------------------------------------------------------------- |
| * Cache Configuration |
| */ |
| #define CONFIG_SYS_CACHELINE_SIZE 32 /* For all MPC74xx CPUs */ |
| #if defined(CONFIG_CMD_KGDB) |
| #define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ |
| #endif |
| |
| /*----------------------------------------------------------------------- |
| * L2CR setup -- make sure this is right for your board! |
| * look in include/74xx_7xx.h for the defines used here |
| */ |
| |
| #define CONFIG_SYS_L2 |
| |
| #ifdef CONFIG_750CX |
| #define L2_INIT 0 |
| #else |
| #define L2_INIT (L2CR_L2SIZ_2M | L2CR_L2CLK_3 | L2CR_L2RAM_BURST | \ |
| L2CR_L2OH_5 | L2CR_L2CTL | L2CR_L2WT) |
| #endif |
| |
| #define L2_ENABLE (L2_INIT | L2CR_L2E) |
| |
| /*------------------------------------------------------------------------ |
| * Real time clock |
| */ |
| #define CONFIG_RTC_DS1302 |
| |
| |
| /*------------------------------------------------------------------------ |
| * Galileo I2C driver |
| */ |
| #define CONFIG_GT_I2C |
| |
| #endif /* __CONFIG_H */ |