include/configs/TOP5200.h - github/trini/u-boot - Gitiles

 /*
  * (C) Copyright 2003
  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
  *
  * modified for TOP5200-series by Reinhard Meyer, www.emk-elektronik.de
  *
  * TOP5200 differences from IceCube:
  * 1 FLASH Bank for one Chip only, up to 64 MB in 16 MB Banks
  *   bank switch controlled by TIMER_6(LSB) and TIMER_7(MSB) Pins
  * 1 SDRAM/DDRAM Bank up to 256 MB
  * local VPD I2C Bus is software driven and uses
  *   GPIO_WKUP_6 for SDA, GPIO_WKUP_7 for SCL
  * FLASH is re-located at 0xff000000
  * Internal regs are at 0xf0000000
  * Reset jumps to 0x00000100
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */

 #ifndef __CONFIG_H
 #define __CONFIG_H

 /*
  * High Level Configuration Options
  * (easy to change)
  */

 #define CONFIG_MPC5xxx		1	/* This is an MPC5xxx CPU */
 #define CONFIG_MPC5200		1	/* More exactly a MPC5200 */
 #define CONFIG_TOP5200		1	/* ... on TOP5200 board - we need this for FEC.C */

 /*
  * allowed and functional CONFIG_SYS_TEXT_BASE values:
  * 0xff000000	low boot at 0x00000100 (default board setting)
  * 0xfff00000	high boot at 0xfff00100 (board needs modification)
  * 0x00100000	RAM load and test
  */
 #define	CONFIG_SYS_TEXT_BASE	0xff000000

 #define CONFIG_SYS_MPC5XXX_CLKIN	33000000 /* ... running at 33.000000MHz */

 #define CONFIG_HIGH_BATS	1	/* High BATs supported */

 /*
  * Serial console configuration
  */
 #define CONFIG_PSC_CONSOLE	1	/* console is on PSC1 */
 #define CONFIG_BAUDRATE		9600	/* ... at 9600 bps */
 #define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200, 230400 }


 #if defined (CONFIG_EVAL5200) || defined (CONFIG_LITE5200)
 /*
  * PCI Mapping:
  * 0x40000000 - 0x4fffffff - PCI Memory
  * 0x50000000 - 0x50ffffff - PCI IO Space
  */
 #  define CONFIG_PCI		1
 #  define CONFIG_PCI_PNP		1
 #  define CONFIG_PCI_SCAN_SHOW	1
 #  define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE	1

 #  define CONFIG_PCI_MEM_BUS	0x40000000
 #  define CONFIG_PCI_MEM_PHYS	CONFIG_PCI_MEM_BUS
 #  define CONFIG_PCI_MEM_SIZE	0x10000000

 #  define CONFIG_PCI_IO_BUS	0x50000000
 #  define CONFIG_PCI_IO_PHYS	CONFIG_PCI_IO_BUS
 #  define CONFIG_PCI_IO_SIZE	0x01000000

 #endif

 /* USB */
 #if defined (CONFIG_EVAL5200) || defined (CONFIG_LITE5200)

 #  define CONFIG_USB_OHCI
 #  define CONFIG_USB_CLOCK	0x0001bbbb
 #  if defined (CONFIG_EVAL5200)
 #    define CONFIG_USB_CONFIG	0x00005100
 #  else
 #    define CONFIG_USB_CONFIG	0x00001000
 #  endif
 #  define CONFIG_DOS_PARTITION
 #  define CONFIG_USB_STORAGE

 #endif

 /* IDE */
 #if defined (CONFIG_EVAL5200) || defined (CONFIG_LITE5200)
 #  define CONFIG_DOS_PARTITION
 #endif


 /*
  * BOOTP options
  */
 #define CONFIG_BOOTP_BOOTFILESIZE
 #define CONFIG_BOOTP_BOOTPATH
 #define CONFIG_BOOTP_GATEWAY
 #define CONFIG_BOOTP_HOSTNAME


 /*
  * Command line configuration.
  */
 #include <config_cmd_default.h>

 #define CONFIG_CMD_ASKENV
 #define CONFIG_CMD_BEDBUG
 #define CONFIG_CMD_DATE
 #define CONFIG_CMD_DHCP
 #define CONFIG_CMD_EEPROM
 #define CONFIG_CMD_ELF
 #define CONFIG_CMD_I2C
 #define CONFIG_CMD_IMMAP
 #define CONFIG_CMD_MII
 #define CONFIG_CMD_REGINFO

 #if defined (CONFIG_EVAL5200) || defined (CONFIG_LITE5200)
 #define CONFIG_CMD_FAT
 #define CONFIG_CMD_IDE
 #define CONFIG_CMD_USB
 #define CONFIG_CMD_PCI
 #endif


 /*
  * MUST be low boot - HIGHBOOT is not supported anymore
  */
 #if (CONFIG_SYS_TEXT_BASE == 0xFF000000)		/* Boot low with 16 MB Flash */
 #   define CONFIG_SYS_LOWBOOT		1
 #   define CONFIG_SYS_LOWBOOT16	1
 #else
 #   error "CONFIG_SYS_TEXT_BASE must be 0xff000000"
 #endif

 /*
  * Autobooting
  */
 #define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds */

 #define CONFIG_PREBOOT	"echo;"	\
 	"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
 	"echo"

 #undef	CONFIG_BOOTARGS

 #define	CONFIG_EXTRA_ENV_SETTINGS					\
 	"netdev=eth0\0"							\
 	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
 		"nfsroot=${serverip}:${rootpath}\0"			\
 	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
 	"addip=setenv bootargs ${bootargs} "				\
 		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
 		":${hostname}:${netdev}:off panic=1\0"			\
 	"flash_nfs=run nfsargs addip;"					\
 		"bootm ${kernel_addr}\0"				\
 	"flash_self=run ramargs addip;"					\
 		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
 	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0"	\
 	"rootpath=/opt/eldk/ppc_82xx\0"					\
 	"bootfile=/tftpboot/MPC5200/uImage\0"				\
 	""

 #define CONFIG_BOOTCOMMAND	"run flash_self"

 /*
  * IPB Bus clocking configuration.
  */
 #undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK		/* define for 133MHz speed */

 /*
  * I2C configuration
  */
 /*
  * EEPROM configuration
  */
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	3
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	70

 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
 #define CONFIG_SYS_EEPROM_SIZE 0x2000

 #define CONFIG_ENV_OVERWRITE
 #define CONFIG_MISC_INIT_R

 #define CONFIG_SYS_I2C_SOFT		/* I2C bit-banged */

 #if defined(CONFIG_SYS_I2C_SOFT)
 #  define CONFIG_SYS_I2C
 #  define CONFIG_SYS_I2C_SOFT_SPEED	100000
 #  define CONFIG_SYS_I2C_SOFT_SLAVE	0x7F
 /**/
 #  define SDA0			0x40
 #  define SCL0			0x80
 #  define GPIOE0		*((volatile uchar*)(CONFIG_SYS_MBAR+0x0c00))
 #  define DDR0			*((volatile uchar*)(CONFIG_SYS_MBAR+0x0c08))
 #  define DVO0			*((volatile uchar*)(CONFIG_SYS_MBAR+0x0c0c))
 #  define DVI0			*((volatile uchar*)(CONFIG_SYS_MBAR+0x0c20))
 #  define ODE0			*((volatile uchar*)(CONFIG_SYS_MBAR+0x0c04))
 #  define I2C_INIT		{GPIOE0|=(SDA0|SCL0);ODE0|=(SDA0|SCL0);DVO0|=(SDA0|SCL0);DDR0|=(SDA0|SCL0);}
 #  define I2C_READ		((DVI0&SDA0)?1:0)
 #  define I2C_SDA(x)	{if(x)DVO0|=SDA0;else DVO0&=~SDA0;}
 #  define I2C_SCL(x)	{if(x)DVO0|=SCL0;else DVO0&=~SCL0;}
 #  define I2C_DELAY		{udelay(5);}
 #  define I2C_ACTIVE	{DDR0|=SDA0;}
 #  define I2C_TRISTATE	{DDR0&=~SDA0;}

 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
 #define CONFIG_SYS_I2C_FACT_ADDR	0x57
 #endif

 #if defined (CONFIG_HARD_I2C)
 #  define CONFIG_SYS_I2C_MODULE	2		/* Select I2C module #1 or #2 */
 #  define CONFIG_SYS_I2C_SPEED		100000	/* 100 kHz */
 #  define CONFIG_SYS_I2C_SLAVE		0x7F
 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x54
 #define CONFIG_SYS_I2C_FACT_ADDR	0x54
 #endif

 /*
  * Flash configuration, expect one 16 Megabyte Bank at most
  */
 #define CONFIG_SYS_FLASH_BASE		0xff000000
 #define CONFIG_SYS_FLASH_SIZE		0x01000000
 #define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max num of memory banks      */
 #define CONFIG_ENV_ADDR		(CONFIG_SYS_FLASH_BASE + 0)

 #define CONFIG_SYS_MAX_FLASH_SECT	256	/* max num of sects on one chip */

 #define CONFIG_SYS_FLASH_ERASE_TOUT	240000	/* Flash Erase Timeout (in ms)  */
 #define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (in ms)  */

 #undef CONFIG_FLASH_16BIT	/* Flash is 8-bit */

 /*
  * DRAM configuration - will be read from VPD later... TODO!
  */
 #if 0
 /* 2x MT48LC16M16A2 - 7.0 ns SDRAMS = 64 MegaBytes Total */
 #define	CONFIG_SYS_DRAM_DDR		0
 #define CONFIG_SYS_DRAM_EMODE		0
 #define CONFIG_SYS_DRAM_MODE		0x008D
 #define CONFIG_SYS_DRAM_CONTROL	0x514F0000
 #define CONFIG_SYS_DRAM_CONFIG1	0xC2233A00
 #define CONFIG_SYS_DRAM_CONFIG2	0x88B70004
 #define	CONFIG_SYS_DRAM_TAP_DEL	0x08
 #define CONFIG_SYS_DRAM_RAM_SIZE	0x19
 #endif
 #if 1
 /* 2x MT48LC16M16A2 - 7.5 ns SDRAMS = 64 MegaBytes Total */
 #define	CONFIG_SYS_DRAM_DDR		0
 #define CONFIG_SYS_DRAM_EMODE		0
 #define CONFIG_SYS_DRAM_MODE		0x00CD
 #define CONFIG_SYS_DRAM_CONTROL	0x514F0000
 #define CONFIG_SYS_DRAM_CONFIG1	0xD2333A00
 #define CONFIG_SYS_DRAM_CONFIG2	0x8AD70004
 #define	CONFIG_SYS_DRAM_TAP_DEL	0x08
 #define CONFIG_SYS_DRAM_RAM_SIZE	0x19
 #endif

 /*
  * Environment settings
  */
 #define CONFIG_ENV_IS_IN_EEPROM	1	/* turn on EEPROM env feature */
 #define CONFIG_ENV_OFFSET		0x1000
 #define CONFIG_ENV_SIZE		0x0700

 /*
  * VPD settings
  */
 #define CONFIG_SYS_FACT_OFFSET		0x1800
 #define CONFIG_SYS_FACT_SIZE		0x0800

 /*
  * Memory map
  *
  * Warning!!! with the current BestComm Task, MBAR MUST BE set to 0xf0000000
  */
 #define CONFIG_SYS_MBAR			0xf0000000	/* DO NOT CHANGE this */
 #define CONFIG_SYS_SDRAM_BASE		0x00000000
 #define CONFIG_SYS_DEFAULT_MBAR	0x80000000

 /* Use SRAM until RAM will be available */
 #define CONFIG_SYS_INIT_RAM_ADDR	MPC5XXX_SRAM
 #define CONFIG_SYS_INIT_RAM_SIZE	MPC5XXX_SRAM_SIZE	/* Size of used area in DPRAM */


 #define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET

 #define CONFIG_SYS_MONITOR_BASE    CONFIG_SYS_TEXT_BASE
 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
 #   define CONFIG_SYS_RAMBOOT		1
 #endif

 #define CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
 #define CONFIG_SYS_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()	*/
 #define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */

 /*
  * Ethernet configuration
  */
 #define CONFIG_MPC5xxx_FEC	1
 #define CONFIG_MPC5xxx_FEC_MII10	/* Workaround for FEC 100Mbit problem */
 #define	CONFIG_PHY_ADDR		0x1f
 #define	CONFIG_PHY_TYPE		0x79c874
 /*
  * GPIO configuration:
  * PSC1,2,3 predefined as UART
  * PCI disabled
  * Ethernet 100 with MD
  */
 #define CONFIG_SYS_GPS_PORT_CONFIG	0x00058044

 /*
  * Miscellaneous configurable options
  */
 #define CONFIG_SYS_LONGHELP			/* undef to save memory	    */
 #if defined(CONFIG_CMD_KGDB)
 #  define CONFIG_SYS_CBSIZE		1024	/* Console I/O Buffer Size  */
 #else
 #  define CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size  */
 #endif
 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)	/* Print Buffer Size */
 #define CONFIG_SYS_MAXARGS		16		/* max number of command args	*/
 #define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/

 #define CONFIG_SYS_MEMTEST_START	0x00100000	/* memtest works on */
 #define CONFIG_SYS_MEMTEST_END		0x01f00000	/* 1 ... 31 MB in DRAM	*/

 #define CONFIG_SYS_LOAD_ADDR		0x200000	/* default load address */

 #define CONFIG_SYS_CACHELINE_SIZE	32	/* For MPC5xxx CPUs */
 #if defined(CONFIG_CMD_KGDB)
 #  define CONFIG_SYS_CACHELINE_SHIFT	5	/* log base 2 of the above value */
 #endif


 #ifdef CONFIG_EVAL5200		/* M48T08 is available with the Evaluation board only */
   #define CONFIG_RTC_MK48T59	1	/* use M48T08 on EVAL5200 */
   #define RTC(reg)		(0xf0010000+reg)
   /* setup CS2 for M48T08. Must MAP 64kB */
   #define CONFIG_SYS_CS2_START	RTC(0)
   #define CONFIG_SYS_CS2_SIZE	0x10000
   /* setup CS2 configuration register: */
   /* WaitP = 0, WaitX = 4, MX=0, AL=1, AA=1, CE=1 */
   /* AS=2, DS=0, Bank=0, WTyp=0, WS=0, RS=0, WO=0, RO=0 */
   #define CONFIG_SYS_CS2_CFG	0x00047800
 #else
   #define CONFIG_RTC_MPC5200	1	/* use internal MPC5200 RTC */
 #endif

 /*
  * Various low-level settings
  */
 #define CONFIG_SYS_HID0_INIT		HID0_ICE | HID0_ICFI
 #define CONFIG_SYS_HID0_FINAL		HID0_ICE

 #define CONFIG_SYS_BOOTCS_START	CONFIG_SYS_FLASH_BASE
 #define CONFIG_SYS_BOOTCS_SIZE		CONFIG_SYS_FLASH_SIZE
 #define CONFIG_SYS_BOOTCS_CFG		0x00047801
 #define CONFIG_SYS_CS0_START		CONFIG_SYS_FLASH_BASE
 #define CONFIG_SYS_CS0_SIZE		CONFIG_SYS_FLASH_SIZE

 #define CONFIG_SYS_CS_BURST		0x00000000
 #define CONFIG_SYS_CS_DEADCYCLE	0x33333333

 #define CONFIG_SYS_RESET_ADDRESS	0x7f000000

 /*-----------------------------------------------------------------------
  * IDE/ATA stuff Supports IDE harddisk
  *-----------------------------------------------------------------------
  */

 #undef  CONFIG_IDE_8xx_PCCARD		/* Use IDE with PC Card	Adapter	*/

 #undef	CONFIG_IDE_8xx_DIRECT		/* Direct IDE    not supported	*/
 #undef	CONFIG_IDE_LED			/* LED   for ide not supported	*/

 #define CONFIG_IDE_RESET	1
 #define CONFIG_IDE_PREINIT

 #define CONFIG_SYS_IDE_MAXBUS		1	/* max. 1 IDE bus		*/
 #define CONFIG_SYS_IDE_MAXDEVICE	1	/* max. 1 drive per IDE bus	*/

 #define CONFIG_SYS_ATA_IDE0_OFFSET	0x0000

 #define CONFIG_SYS_ATA_BASE_ADDR	MPC5XXX_ATA

 /* Offset for data I/O			*/
 #define CONFIG_SYS_ATA_DATA_OFFSET	(0x0060)

 /* Offset for normal register accesses	*/
 #define CONFIG_SYS_ATA_REG_OFFSET	(CONFIG_SYS_ATA_DATA_OFFSET)

 /* Offset for alternate registers	*/
 #define CONFIG_SYS_ATA_ALT_OFFSET	(0x005c)

 /* Interval between registers                                                */
 #define CONFIG_SYS_ATA_STRIDE          4

 #endif /* __CONFIG_H */
	/*
	* (C) Copyright 2003
	* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
	*
	* modified for TOP5200-series by Reinhard Meyer, www.emk-elektronik.de
	*
	* TOP5200 differences from IceCube:
	* 1 FLASH Bank for one Chip only, up to 64 MB in 16 MB Banks
	* bank switch controlled by TIMER_6(LSB) and TIMER_7(MSB) Pins
	* 1 SDRAM/DDRAM Bank up to 256 MB
	* local VPD I2C Bus is software driven and uses
	* GPIO_WKUP_6 for SDA, GPIO_WKUP_7 for SCL
	* FLASH is re-located at 0xff000000
	* Internal regs are at 0xf0000000
	* Reset jumps to 0x00000100
	*
	* SPDX-License-Identifier: GPL-2.0+
	*/

	#ifndef __CONFIG_H
	#define __CONFIG_H

	/*
	* High Level Configuration Options
	* (easy to change)
	*/

	#define CONFIG_MPC5xxx 1 /* This is an MPC5xxx CPU */
	#define CONFIG_MPC5200 1 /* More exactly a MPC5200 */
	#define CONFIG_TOP5200 1 /* ... on TOP5200 board - we need this for FEC.C */

	/*
	* allowed and functional CONFIG_SYS_TEXT_BASE values:
	* 0xff000000 low boot at 0x00000100 (default board setting)
	* 0xfff00000 high boot at 0xfff00100 (board needs modification)
	* 0x00100000 RAM load and test
	*/
	#define CONFIG_SYS_TEXT_BASE 0xff000000

	#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */

	#define CONFIG_HIGH_BATS 1 /* High BATs supported */

	/*
	* Serial console configuration
	*/
	#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */
	#define CONFIG_BAUDRATE 9600 /* ... at 9600 bps */
	#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }


	#if defined (CONFIG_EVAL5200) \|\| defined (CONFIG_LITE5200)
	/*
	* PCI Mapping:
	* 0x40000000 - 0x4fffffff - PCI Memory
	* 0x50000000 - 0x50ffffff - PCI IO Space
	*/
	# define CONFIG_PCI 1
	# define CONFIG_PCI_PNP 1
	# define CONFIG_PCI_SCAN_SHOW 1
	# define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1

	# define CONFIG_PCI_MEM_BUS 0x40000000
	# define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS
	# define CONFIG_PCI_MEM_SIZE 0x10000000

	# define CONFIG_PCI_IO_BUS 0x50000000
	# define CONFIG_PCI_IO_PHYS CONFIG_PCI_IO_BUS
	# define CONFIG_PCI_IO_SIZE 0x01000000

	#endif

	/* USB */
	#if defined (CONFIG_EVAL5200) \|\| defined (CONFIG_LITE5200)

	# define CONFIG_USB_OHCI
	# define CONFIG_USB_CLOCK 0x0001bbbb
	# if defined (CONFIG_EVAL5200)
	# define CONFIG_USB_CONFIG 0x00005100
	# else
	# define CONFIG_USB_CONFIG 0x00001000
	# endif
	# define CONFIG_DOS_PARTITION
	# define CONFIG_USB_STORAGE

	#endif

	/* IDE */
	#if defined (CONFIG_EVAL5200) \|\| defined (CONFIG_LITE5200)
	# define CONFIG_DOS_PARTITION
	#endif


	/*
	* BOOTP options
	*/
	#define CONFIG_BOOTP_BOOTFILESIZE
	#define CONFIG_BOOTP_BOOTPATH
	#define CONFIG_BOOTP_GATEWAY
	#define CONFIG_BOOTP_HOSTNAME


	/*
	* Command line configuration.
	*/
	#include <config_cmd_default.h>

	#define CONFIG_CMD_ASKENV
	#define CONFIG_CMD_BEDBUG
	#define CONFIG_CMD_DATE
	#define CONFIG_CMD_DHCP
	#define CONFIG_CMD_EEPROM
	#define CONFIG_CMD_ELF
	#define CONFIG_CMD_I2C
	#define CONFIG_CMD_IMMAP
	#define CONFIG_CMD_MII
	#define CONFIG_CMD_REGINFO

	#if defined (CONFIG_EVAL5200) \|\| defined (CONFIG_LITE5200)
	#define CONFIG_CMD_FAT
	#define CONFIG_CMD_IDE
	#define CONFIG_CMD_USB
	#define CONFIG_CMD_PCI
	#endif


	/*
	* MUST be low boot - HIGHBOOT is not supported anymore
	*/
	#if (CONFIG_SYS_TEXT_BASE == 0xFF000000) /* Boot low with 16 MB Flash */
	# define CONFIG_SYS_LOWBOOT 1
	# define CONFIG_SYS_LOWBOOT16 1
	#else
	# error "CONFIG_SYS_TEXT_BASE must be 0xff000000"
	#endif

	/*
	* Autobooting
	*/
	#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */

	#define CONFIG_PREBOOT "echo;" \
	"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
	"echo"

	#undef CONFIG_BOOTARGS

	#define CONFIG_EXTRA_ENV_SETTINGS \
	"netdev=eth0\0" \
	"nfsargs=setenv bootargs root=/dev/nfs rw " \
	"nfsroot=${serverip}:${rootpath}\0" \
	"ramargs=setenv bootargs root=/dev/ram rw\0" \
	"addip=setenv bootargs ${bootargs} " \
	"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
	":${hostname}:${netdev}:off panic=1\0" \
	"flash_nfs=run nfsargs addip;" \
	"bootm ${kernel_addr}\0" \
	"flash_self=run ramargs addip;" \
	"bootm ${kernel_addr} ${ramdisk_addr}\0" \
	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \
	"rootpath=/opt/eldk/ppc_82xx\0" \
	"bootfile=/tftpboot/MPC5200/uImage\0" \
	""

	#define CONFIG_BOOTCOMMAND "run flash_self"

	/*
	* IPB Bus clocking configuration.
	*/
	#undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */

	/*
	* I2C configuration
	*/
	/*
	* EEPROM configuration
	*/
	#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
	#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 70

	#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
	#define CONFIG_SYS_EEPROM_SIZE 0x2000

	#define CONFIG_ENV_OVERWRITE
	#define CONFIG_MISC_INIT_R

	#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */

	#if defined(CONFIG_SYS_I2C_SOFT)
	# define CONFIG_SYS_I2C
	# define CONFIG_SYS_I2C_SOFT_SPEED 100000
	# define CONFIG_SYS_I2C_SOFT_SLAVE 0x7F
	/**/
	# define SDA0 0x40
	# define SCL0 0x80
	# define GPIOE0 ((volatile uchar)(CONFIG_SYS_MBAR+0x0c00))
	# define DDR0 ((volatile uchar)(CONFIG_SYS_MBAR+0x0c08))
	# define DVO0 ((volatile uchar)(CONFIG_SYS_MBAR+0x0c0c))
	# define DVI0 ((volatile uchar)(CONFIG_SYS_MBAR+0x0c20))
	# define ODE0 ((volatile uchar)(CONFIG_SYS_MBAR+0x0c04))
	# define I2C_INIT {GPIOE0\|=(SDA0\|SCL0);ODE0\|=(SDA0\|SCL0);DVO0\|=(SDA0\|SCL0);DDR0\|=(SDA0\|SCL0);}
	# define I2C_READ ((DVI0&SDA0)?1:0)
	# define I2C_SDA(x) {if(x)DVO0\|=SDA0;else DVO0&=~SDA0;}
	# define I2C_SCL(x) {if(x)DVO0\|=SCL0;else DVO0&=~SCL0;}
	# define I2C_DELAY {udelay(5);}
	# define I2C_ACTIVE {DDR0\|=SDA0;}
	# define I2C_TRISTATE {DDR0&=~SDA0;}

	#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
	#define CONFIG_SYS_I2C_FACT_ADDR 0x57
	#endif

	#if defined (CONFIG_HARD_I2C)
	# define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */
	# define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
	# define CONFIG_SYS_I2C_SLAVE 0x7F
	#define CONFIG_SYS_I2C_EEPROM_ADDR 0x54
	#define CONFIG_SYS_I2C_FACT_ADDR 0x54
	#endif

	/*
	* Flash configuration, expect one 16 Megabyte Bank at most
	*/
	#define CONFIG_SYS_FLASH_BASE 0xff000000
	#define CONFIG_SYS_FLASH_SIZE 0x01000000
	#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of memory banks */
	#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0)

	#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max num of sects on one chip */

	#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */
	#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */

	#undef CONFIG_FLASH_16BIT /* Flash is 8-bit */

	/*
	* DRAM configuration - will be read from VPD later... TODO!
	*/
	#if 0
	/* 2x MT48LC16M16A2 - 7.0 ns SDRAMS = 64 MegaBytes Total */
	#define CONFIG_SYS_DRAM_DDR 0
	#define CONFIG_SYS_DRAM_EMODE 0
	#define CONFIG_SYS_DRAM_MODE 0x008D
	#define CONFIG_SYS_DRAM_CONTROL 0x514F0000
	#define CONFIG_SYS_DRAM_CONFIG1 0xC2233A00
	#define CONFIG_SYS_DRAM_CONFIG2 0x88B70004
	#define CONFIG_SYS_DRAM_TAP_DEL 0x08
	#define CONFIG_SYS_DRAM_RAM_SIZE 0x19
	#endif
	#if 1
	/* 2x MT48LC16M16A2 - 7.5 ns SDRAMS = 64 MegaBytes Total */
	#define CONFIG_SYS_DRAM_DDR 0
	#define CONFIG_SYS_DRAM_EMODE 0
	#define CONFIG_SYS_DRAM_MODE 0x00CD
	#define CONFIG_SYS_DRAM_CONTROL 0x514F0000
	#define CONFIG_SYS_DRAM_CONFIG1 0xD2333A00
	#define CONFIG_SYS_DRAM_CONFIG2 0x8AD70004
	#define CONFIG_SYS_DRAM_TAP_DEL 0x08
	#define CONFIG_SYS_DRAM_RAM_SIZE 0x19
	#endif

	/*
	* Environment settings
	*/
	#define CONFIG_ENV_IS_IN_EEPROM 1 /* turn on EEPROM env feature */
	#define CONFIG_ENV_OFFSET 0x1000
	#define CONFIG_ENV_SIZE 0x0700

	/*
	* VPD settings
	*/
	#define CONFIG_SYS_FACT_OFFSET 0x1800
	#define CONFIG_SYS_FACT_SIZE 0x0800

	/*
	* Memory map
	*
	* Warning!!! with the current BestComm Task, MBAR MUST BE set to 0xf0000000
	*/
	#define CONFIG_SYS_MBAR 0xf0000000 /* DO NOT CHANGE this */
	#define CONFIG_SYS_SDRAM_BASE 0x00000000
	#define CONFIG_SYS_DEFAULT_MBAR 0x80000000

	/* Use SRAM until RAM will be available */
	#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM
	#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE /* Size of used area in DPRAM */


	#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
	#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET

	#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
	#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
	# define CONFIG_SYS_RAMBOOT 1
	#endif

	#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
	#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
	#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */

	/*
	* Ethernet configuration
	*/
	#define CONFIG_MPC5xxx_FEC 1
	#define CONFIG_MPC5xxx_FEC_MII10 /* Workaround for FEC 100Mbit problem */
	#define CONFIG_PHY_ADDR 0x1f
	#define CONFIG_PHY_TYPE 0x79c874
	/*
	* GPIO configuration:
	* PSC1,2,3 predefined as UART
	* PCI disabled
	* Ethernet 100 with MD
	*/
	#define CONFIG_SYS_GPS_PORT_CONFIG 0x00058044

	/*
	* Miscellaneous configurable options
	*/
	#define CONFIG_SYS_LONGHELP /* undef to save memory */
	#if defined(CONFIG_CMD_KGDB)
	# define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
	#else
	# define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
	#endif
	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
	#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */

	#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
	#define CONFIG_SYS_MEMTEST_END 0x01f00000 /* 1 ... 31 MB in DRAM */

	#define CONFIG_SYS_LOAD_ADDR 0x200000 /* default load address */

	#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
	#if defined(CONFIG_CMD_KGDB)
	# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
	#endif


	#ifdef CONFIG_EVAL5200 /* M48T08 is available with the Evaluation board only */
	#define CONFIG_RTC_MK48T59 1 /* use M48T08 on EVAL5200 */
	#define RTC(reg) (0xf0010000+reg)
	/* setup CS2 for M48T08. Must MAP 64kB */
	#define CONFIG_SYS_CS2_START RTC(0)
	#define CONFIG_SYS_CS2_SIZE 0x10000
	/* setup CS2 configuration register: */
	/* WaitP = 0, WaitX = 4, MX=0, AL=1, AA=1, CE=1 */
	/* AS=2, DS=0, Bank=0, WTyp=0, WS=0, RS=0, WO=0, RO=0 */
	#define CONFIG_SYS_CS2_CFG 0x00047800
	#else
	#define CONFIG_RTC_MPC5200 1 /* use internal MPC5200 RTC */
	#endif

	/*
	* Various low-level settings
	*/
	#define CONFIG_SYS_HID0_INIT HID0_ICE \| HID0_ICFI
	#define CONFIG_SYS_HID0_FINAL HID0_ICE

	#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE
	#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE
	#define CONFIG_SYS_BOOTCS_CFG 0x00047801
	#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE
	#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE

	#define CONFIG_SYS_CS_BURST 0x00000000
	#define CONFIG_SYS_CS_DEADCYCLE 0x33333333

	#define CONFIG_SYS_RESET_ADDRESS 0x7f000000

	/*-----------------------------------------------------------------------
	* IDE/ATA stuff Supports IDE harddisk
	*-----------------------------------------------------------------------
	*/

	#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */

	#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
	#undef CONFIG_IDE_LED /* LED for ide not supported */

	#define CONFIG_IDE_RESET 1
	#define CONFIG_IDE_PREINIT

	#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
	#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */

	#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000

	#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA

	/* Offset for data I/O */
	#define CONFIG_SYS_ATA_DATA_OFFSET (0x0060)

	/* Offset for normal register accesses */
	#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET)

	/* Offset for alternate registers */
	#define CONFIG_SYS_ATA_ALT_OFFSET (0x005c)

	/* Interval between registers */
	#define CONFIG_SYS_ATA_STRIDE 4

	#endif /* __CONFIG_H */