include/configs/MPC8548CDS.h - github/trini/u-boot - Gitiles

 /*
  * Copyright 2004, 2007, 2010-2011 Freescale Semiconductor.
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */

 /*
  * mpc8548cds board configuration file
  *
  * Please refer to doc/README.mpc85xxcds for more info.
  *
  */
 #ifndef __CONFIG_H
 #define __CONFIG_H

 #ifdef CONFIG_36BIT
 #define CONFIG_PHYS_64BIT
 #endif

 /* High Level Configuration Options */
 #define CONFIG_BOOKE		1	/* BOOKE */
 #define CONFIG_E500		1	/* BOOKE e500 family */
 #define CONFIG_MPC85xx		1	/* MPC8540/60/55/41/48 */
 #define CONFIG_MPC8548		1	/* MPC8548 specific */
 #define CONFIG_MPC8548CDS	1	/* MPC8548CDS board specific */

 #ifndef CONFIG_SYS_TEXT_BASE
 #define CONFIG_SYS_TEXT_BASE	0xfff80000
 #endif

 #define CONFIG_SYS_SRIO
 #define CONFIG_SRIO1			/* SRIO port 1 */

 #define CONFIG_PCI		/* enable any pci type devices */
 #define CONFIG_PCI1		/* PCI controller 1 */
 #define CONFIG_PCIE1		/* PCIE controler 1 (slot 1) */
 #undef CONFIG_PCI2
 #define CONFIG_FSL_PCI_INIT	1	/* Use common FSL init code */
 #define CONFIG_PCI_INDIRECT_BRIDGE 1	/* indirect PCI bridge support */
 #define CONFIG_FSL_PCIE_RESET	1	/* need PCIe reset errata */
 #define CONFIG_SYS_PCI_64BIT	1	/* enable 64-bit PCI resources */

 #define CONFIG_TSEC_ENET		/* tsec ethernet support */
 #define CONFIG_ENV_OVERWRITE
 #define CONFIG_INTERRUPTS		/* enable pci, srio, ddr interrupts */
 #define CONFIG_FSL_LAW		1	/* Use common FSL init code */

 #define CONFIG_FSL_VIA

 #ifndef __ASSEMBLY__
 extern unsigned long get_clock_freq(void);
 #endif
 #define CONFIG_SYS_CLK_FREQ	get_clock_freq() /* sysclk for MPC85xx */

 /*
  * These can be toggled for performance analysis, otherwise use default.
  */
 #define CONFIG_L2_CACHE			/* toggle L2 cache */
 #define CONFIG_BTB			/* toggle branch predition */

 /*
  * Only possible on E500 Version 2 or newer cores.
  */
 #define CONFIG_ENABLE_36BIT_PHYS	1

 #ifdef CONFIG_PHYS_64BIT
 #define CONFIG_ADDR_MAP
 #define CONFIG_SYS_NUM_ADDR_MAP		16	/* number of TLB1 entries */
 #endif

 #define CONFIG_SYS_MEMTEST_START	0x00200000	/* memtest works on */
 #define CONFIG_SYS_MEMTEST_END		0x00400000

 #define CONFIG_SYS_CCSRBAR		0xe0000000
 #define CONFIG_SYS_CCSRBAR_PHYS_LOW	CONFIG_SYS_CCSRBAR

 /* DDR Setup */
 #define CONFIG_SYS_FSL_DDR2
 #undef CONFIG_FSL_DDR_INTERACTIVE
 #define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup*/
 #define CONFIG_DDR_SPD

 #define CONFIG_DDR_ECC
 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER	/* DDR controller or DMA? */
 #define CONFIG_MEM_INIT_VALUE	0xDeadBeef

 #define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000	/* DDR is system memory*/
 #define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE

 #define CONFIG_NUM_DDR_CONTROLLERS	1
 #define CONFIG_DIMM_SLOTS_PER_CTLR	1
 #define CONFIG_CHIP_SELECTS_PER_CTRL	(2 * CONFIG_DIMM_SLOTS_PER_CTLR)

 /* I2C addresses of SPD EEPROMs */
 #define SPD_EEPROM_ADDRESS	0x51	/* CTLR 0 DIMM 0 */

 /* Make sure required options are set */
 #ifndef CONFIG_SPD_EEPROM
 #error ("CONFIG_SPD_EEPROM is required")
 #endif

 #undef CONFIG_CLOCKS_IN_MHZ
 /*
  * Physical Address Map
  *
  * 32bit:
  * 0x0000_0000	0x7fff_ffff	DDR			2G	cacheable
  * 0x8000_0000	0x9fff_ffff	PCI1 MEM		512M	cacheable
  * 0xa000_0000	0xbfff_ffff	PCIe MEM		512M	cacheable
  * 0xc000_0000	0xdfff_ffff	RapidIO			512M	cacheable
  * 0xe000_0000	0xe00f_ffff	CCSR			1M	non-cacheable
  * 0xe200_0000	0xe20f_ffff	PCI1 IO			1M	non-cacheable
  * 0xe300_0000	0xe30f_ffff	PCIe IO			1M	non-cacheable
  * 0xf000_0000	0xf3ff_ffff	SDRAM			64M	cacheable
  * 0xf800_0000	0xf80f_ffff	NVRAM/CADMUS		1M	non-cacheable
  * 0xff00_0000	0xff7f_ffff	FLASH (2nd bank)	8M	non-cacheable
  * 0xff80_0000	0xffff_ffff	FLASH (boot bank)	8M	non-cacheable
  *
  * 36bit:
  * 0x00000_0000	0x07fff_ffff	DDR			2G	cacheable
  * 0xc0000_0000	0xc1fff_ffff	PCI1 MEM		512M	cacheable
  * 0xc2000_0000	0xc3fff_ffff	PCIe MEM		512M	cacheable
  * 0xc4000_0000	0xc5fff_ffff	RapidIO			512M	cacheable
  * 0xfe000_0000	0xfe00f_ffff	CCSR			1M	non-cacheable
  * 0xfe200_0000	0xfe20f_ffff	PCI1 IO			1M	non-cacheable
  * 0xfe300_0000	0xfe30f_ffff	PCIe IO			1M	non-cacheable
  * 0xff000_0000	0xff3ff_ffff	SDRAM			64M	cacheable
  * 0xff800_0000	0xff80f_ffff	NVRAM/CADMUS		1M	non-cacheable
  * 0xfff00_0000	0xfff7f_ffff	FLASH (2nd bank)	8M	non-cacheable
  * 0xfff80_0000	0xfffff_ffff	FLASH (boot bank)	8M	non-cacheable
  *
  */


 /*
  * Local Bus Definitions
  */

 /*
  * FLASH on the Local Bus
  * Two banks, 8M each, using the CFI driver.
  * Boot from BR0/OR0 bank at 0xff00_0000
  * Alternate BR1/OR1 bank at 0xff80_0000
  *
  * BR0, BR1:
  *    Base address 0 = 0xff00_0000 = BR0[0:16] = 1111 1111 0000 0000 0
  *    Base address 1 = 0xff80_0000 = BR1[0:16] = 1111 1111 1000 0000 0
  *    Port Size = 16 bits = BRx[19:20] = 10
  *    Use GPCM = BRx[24:26] = 000
  *    Valid = BRx[31] = 1
  *
  * 0	4    8	  12   16   20	 24   28
  * 1111 1111 1000 0000 0001 0000 0000 0001 = ff801001	 BR0
  * 1111 1111 0000 0000 0001 0000 0000 0001 = ff001001	 BR1
  *
  * OR0, OR1:
  *    Addr Mask = 8M = ORx[0:16] = 1111 1111 1000 0000 0
  *    Reserved ORx[17:18] = 11, confusion here?
  *    CSNT = ORx[20] = 1
  *    ACS = half cycle delay = ORx[21:22] = 11
  *    SCY = 6 = ORx[24:27] = 0110
  *    TRLX = use relaxed timing = ORx[29] = 1
  *    EAD = use external address latch delay = OR[31] = 1
  *
  * 0	4    8	  12   16   20	 24   28
  * 1111 1111 1000 0000 0110 1110 0110 0101 = ff806e65	 ORx
  */

 #define CONFIG_SYS_FLASH_BASE		0xff000000	/* start of FLASH 16M */
 #ifdef CONFIG_PHYS_64BIT
 #define CONFIG_SYS_FLASH_BASE_PHYS	0xfff000000ull
 #else
 #define CONFIG_SYS_FLASH_BASE_PHYS	CONFIG_SYS_FLASH_BASE
 #endif

 #define CONFIG_SYS_BR0_PRELIM \
 	(BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS + 0x800000) | BR_PS_16 | BR_V)
 #define CONFIG_SYS_BR1_PRELIM \
 	(BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | BR_PS_16 | BR_V)

 #define	CONFIG_SYS_OR0_PRELIM		0xff806e65
 #define	CONFIG_SYS_OR1_PRELIM		0xff806e65

 #define CONFIG_SYS_FLASH_BANKS_LIST \
 	{CONFIG_SYS_FLASH_BASE_PHYS + 0x800000, CONFIG_SYS_FLASH_BASE_PHYS}
 #define CONFIG_SYS_MAX_FLASH_BANKS	2		/* number of banks */
 #define CONFIG_SYS_MAX_FLASH_SECT	128		/* sectors per device */
 #undef	CONFIG_SYS_FLASH_CHECKSUM
 #define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
 #define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */

 #define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor */

 #define CONFIG_FLASH_CFI_DRIVER
 #define CONFIG_SYS_FLASH_CFI
 #define CONFIG_SYS_FLASH_EMPTY_INFO

 #define CONFIG_HWCONFIG			/* enable hwconfig */

 /*
  * SDRAM on the Local Bus
  */
 #define CONFIG_SYS_LBC_SDRAM_BASE	0xf0000000	/* Localbus SDRAM */
 #ifdef CONFIG_PHYS_64BIT
 #define CONFIG_SYS_LBC_SDRAM_BASE_PHYS	0xff0000000ull
 #else
 #define CONFIG_SYS_LBC_SDRAM_BASE_PHYS	CONFIG_SYS_LBC_SDRAM_BASE
 #endif
 #define CONFIG_SYS_LBC_SDRAM_SIZE	64		/* LBC SDRAM is 64MB */

 /*
  * Base Register 2 and Option Register 2 configure SDRAM.
  * The SDRAM base address, CONFIG_SYS_LBC_SDRAM_BASE, is 0xf0000000.
  *
  * For BR2, need:
  *    Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0
  *    port-size = 32-bits = BR2[19:20] = 11
  *    no parity checking = BR2[21:22] = 00
  *    SDRAM for MSEL = BR2[24:26] = 011
  *    Valid = BR[31] = 1
  *
  * 0	4    8	  12   16   20	 24   28
  * 1111 0000 0000 0000 0001 1000 0110 0001 = f0001861
  *
  * FIXME: CONFIG_SYS_LBC_SDRAM_BASE should be masked and OR'ed into
  * FIXME: the top 17 bits of BR2.
  */

 #define CONFIG_SYS_BR2_PRELIM \
 	(BR_PHYS_ADDR(CONFIG_SYS_LBC_SDRAM_BASE_PHYS) \
 	| BR_PS_32 | (3<<BR_MSEL_SHIFT) | BR_V)

 /*
  * The SDRAM size in MB, CONFIG_SYS_LBC_SDRAM_SIZE, is 64.
  *
  * For OR2, need:
  *    64MB mask for AM, OR2[0:7] = 1111 1100
  *		   XAM, OR2[17:18] = 11
  *    9 columns OR2[19-21] = 010
  *    13 rows	OR2[23-25] = 100
  *    EAD set for extra time OR[31] = 1
  *
  * 0	4    8	  12   16   20	 24   28
  * 1111 1100 0000 0000 0110 1001 0000 0001 = fc006901
  */

 #define CONFIG_SYS_OR2_PRELIM		0xfc006901

 #define CONFIG_SYS_LBC_LCRR		0x00030004	/* LB clock ratio reg */
 #define CONFIG_SYS_LBC_LBCR		0x00000000	/* LB config reg */
 #define CONFIG_SYS_LBC_LSRT		0x20000000	/* LB sdram refresh timer */
 #define CONFIG_SYS_LBC_MRTPR		0x00000000	/* LB refresh timer prescal*/

 /*
  * Common settings for all Local Bus SDRAM commands.
  * At run time, either BSMA1516 (for CPU 1.1)
  *		    or BSMA1617 (for CPU 1.0) (old)
  * is OR'ed in too.
  */
 #define CONFIG_SYS_LBC_LSDMR_COMMON	( LSDMR_RFCR16		\
 				| LSDMR_PRETOACT7	\
 				| LSDMR_ACTTORW7	\
 				| LSDMR_BL8		\
 				| LSDMR_WRC4		\
 				| LSDMR_CL3		\
 				| LSDMR_RFEN		\
 				)

 /*
  * The CADMUS registers are connected to CS3 on CDS.
  * The new memory map places CADMUS at 0xf8000000.
  *
  * For BR3, need:
  *    Base address of 0xf8000000 = BR[0:16] = 1111 1000 0000 0000 0
  *    port-size = 8-bits  = BR[19:20] = 01
  *    no parity checking  = BR[21:22] = 00
  *    GPMC for MSEL	  = BR[24:26] = 000
  *    Valid		  = BR[31]    = 1
  *
  * 0	4    8	  12   16   20	 24   28
  * 1111 1000 0000 0000 0000 1000 0000 0001 = f8000801
  *
  * For OR3, need:
  *    1 MB mask for AM,	  OR[0:16]  = 1111 1111 1111 0000 0
  *    disable buffer ctrl OR[19]    = 0
  *    CSNT		  OR[20]    = 1
  *    ACS		  OR[21:22] = 11
  *    XACS		  OR[23]    = 1
  *    SCY 15 wait states  OR[24:27] = 1111	max is suboptimal but safe
  *    SETA		  OR[28]    = 0
  *    TRLX		  OR[29]    = 1
  *    EHTR		  OR[30]    = 1
  *    EAD extra time	  OR[31]    = 1
  *
  * 0	4    8	  12   16   20	 24   28
  * 1111 1111 1111 0000 0000 1111 1111 0111 = fff00ff7
  */

 #define CONFIG_FSL_CADMUS

 #define CADMUS_BASE_ADDR 0xf8000000
 #ifdef CONFIG_PHYS_64BIT
 #define CADMUS_BASE_ADDR_PHYS	0xff8000000ull
 #else
 #define CADMUS_BASE_ADDR_PHYS	CADMUS_BASE_ADDR
 #endif
 #define CONFIG_SYS_BR3_PRELIM \
 	(BR_PHYS_ADDR(CADMUS_BASE_ADDR_PHYS) | BR_PS_8 | BR_V)
 #define CONFIG_SYS_OR3_PRELIM	 0xfff00ff7

 #define CONFIG_SYS_INIT_RAM_LOCK	1
 #define CONFIG_SYS_INIT_RAM_ADDR	0xe4010000	/* Initial RAM address */
 #define CONFIG_SYS_INIT_RAM_SIZE	0x4000		/* Size of used area in RAM */

 #define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET

 #define CONFIG_SYS_MONITOR_LEN		(256 * 1024) /* Reserve 256 kB for Mon */
 #define CONFIG_SYS_MALLOC_LEN	(1024 * 1024)	/* Reserved for malloc */

 /* Serial Port */
 #define CONFIG_CONS_INDEX	2
 #define CONFIG_SYS_NS16550
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE	1
 #define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)

 #define CONFIG_SYS_BAUDRATE_TABLE \
 	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}

 #define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_CCSRBAR+0x4500)
 #define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_CCSRBAR+0x4600)

 /* Use the HUSH parser */
 #define CONFIG_SYS_HUSH_PARSER

 /* pass open firmware flat tree */
 #define CONFIG_OF_LIBFDT		1
 #define CONFIG_OF_BOARD_SETUP		1
 #define CONFIG_OF_STDOUT_VIA_ALIAS	1

 /*
  * I2C
  */
 #define CONFIG_SYS_I2C
 #define CONFIG_SYS_I2C_FSL
 #define CONFIG_SYS_FSL_I2C_SPEED	400000
 #define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
 #define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
 #define CONFIG_SYS_I2C_NOPROBES		{ {0, 0x69} }

 /* EEPROM */
 #define CONFIG_ID_EEPROM
 #define CONFIG_SYS_I2C_EEPROM_CCID
 #define CONFIG_SYS_ID_EEPROM
 #define CONFIG_SYS_I2C_EEPROM_ADDR     0x57
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2

 /*
  * General PCI
  * Memory space is mapped 1-1, but I/O space must start from 0.
  */
 #define CONFIG_SYS_PCI1_MEM_VIRT	0x80000000
 #ifdef CONFIG_PHYS_64BIT
 #define CONFIG_SYS_PCI1_MEM_BUS		0xe0000000
 #define CONFIG_SYS_PCI1_MEM_PHYS	0xc00000000ull
 #else
 #define CONFIG_SYS_PCI1_MEM_BUS	0x80000000
 #define CONFIG_SYS_PCI1_MEM_PHYS	0x80000000
 #endif
 #define CONFIG_SYS_PCI1_MEM_SIZE	0x20000000	/* 512M */
 #define CONFIG_SYS_PCI1_IO_VIRT	0xe2000000
 #define CONFIG_SYS_PCI1_IO_BUS	0x00000000
 #ifdef CONFIG_PHYS_64BIT
 #define CONFIG_SYS_PCI1_IO_PHYS 0xfe2000000ull
 #else
 #define CONFIG_SYS_PCI1_IO_PHYS	0xe2000000
 #endif
 #define CONFIG_SYS_PCI1_IO_SIZE	0x00100000	/* 1M */

 #ifdef CONFIG_PCIE1
 #define CONFIG_SYS_PCIE1_NAME		"Slot"
 #define CONFIG_SYS_PCIE1_MEM_VIRT	0xa0000000
 #ifdef CONFIG_PHYS_64BIT
 #define CONFIG_SYS_PCIE1_MEM_BUS	0xe0000000
 #define CONFIG_SYS_PCIE1_MEM_PHYS	0xc20000000ull
 #else
 #define CONFIG_SYS_PCIE1_MEM_BUS	0xa0000000
 #define CONFIG_SYS_PCIE1_MEM_PHYS	0xa0000000
 #endif
 #define CONFIG_SYS_PCIE1_MEM_SIZE	0x20000000	/* 512M */
 #define CONFIG_SYS_PCIE1_IO_VIRT	0xe3000000
 #define CONFIG_SYS_PCIE1_IO_BUS	0x00000000
 #ifdef CONFIG_PHYS_64BIT
 #define CONFIG_SYS_PCIE1_IO_PHYS        0xfe3000000ull
 #else
 #define CONFIG_SYS_PCIE1_IO_PHYS	0xe3000000
 #endif
 #define CONFIG_SYS_PCIE1_IO_SIZE	0x00100000	/*   1M */
 #endif

 /*
  * RapidIO MMU
  */
 #define CONFIG_SYS_SRIO1_MEM_VIRT	0xc0000000
 #ifdef CONFIG_PHYS_64BIT
 #define CONFIG_SYS_SRIO1_MEM_PHYS	0xc40000000ull
 #else
 #define CONFIG_SYS_SRIO1_MEM_PHYS	0xc0000000
 #endif
 #define CONFIG_SYS_SRIO1_MEM_SIZE	0x20000000	/* 512M */

 #ifdef CONFIG_LEGACY
 #define BRIDGE_ID 17
 #define VIA_ID 2
 #else
 #define BRIDGE_ID 28
 #define VIA_ID 4
 #endif

 #if defined(CONFIG_PCI)

 #define CONFIG_PCI_PNP			/* do pci plug-and-play */

 #undef CONFIG_EEPRO100
 #undef CONFIG_TULIP
 #define CONFIG_E1000			/* Define e1000 pci Ethernet card */

 #define CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */

 #endif	/* CONFIG_PCI */


 #if defined(CONFIG_TSEC_ENET)

 #define CONFIG_MII		1	/* MII PHY management */
 #define CONFIG_TSEC1	1
 #define CONFIG_TSEC1_NAME	"eTSEC0"
 #define CONFIG_TSEC2	1
 #define CONFIG_TSEC2_NAME	"eTSEC1"
 #define CONFIG_TSEC3	1
 #define CONFIG_TSEC3_NAME	"eTSEC2"
 #define CONFIG_TSEC4
 #define CONFIG_TSEC4_NAME	"eTSEC3"
 #undef CONFIG_MPC85XX_FEC

 #define CONFIG_PHY_MARVELL

 #define TSEC1_PHY_ADDR		0
 #define TSEC2_PHY_ADDR		1
 #define TSEC3_PHY_ADDR		2
 #define TSEC4_PHY_ADDR		3

 #define TSEC1_PHYIDX		0
 #define TSEC2_PHYIDX		0
 #define TSEC3_PHYIDX		0
 #define TSEC4_PHYIDX		0
 #define TSEC1_FLAGS		TSEC_GIGABIT
 #define TSEC2_FLAGS		TSEC_GIGABIT
 #define TSEC3_FLAGS		(TSEC_GIGABIT | TSEC_REDUCED)
 #define TSEC4_FLAGS		(TSEC_GIGABIT | TSEC_REDUCED)

 /* Options are: eTSEC[0-3] */
 #define CONFIG_ETHPRIME		"eTSEC0"
 #define CONFIG_PHY_GIGE		1	/* Include GbE speed/duplex detection */
 #endif	/* CONFIG_TSEC_ENET */

 /*
  * Environment
  */
 #define CONFIG_ENV_IS_IN_FLASH	1
 #if CONFIG_SYS_MONITOR_BASE > 0xfff80000
 #define CONFIG_ENV_ADDR	0xfff80000
 #else
 #define CONFIG_ENV_ADDR	(CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
 #endif
 #define CONFIG_ENV_SECT_SIZE	0x20000	/* 128K for env */
 #define CONFIG_ENV_SIZE		0x2000

 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
 #define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change */

 /*
  * BOOTP options
  */
 #define CONFIG_BOOTP_BOOTFILESIZE
 #define CONFIG_BOOTP_BOOTPATH
 #define CONFIG_BOOTP_GATEWAY
 #define CONFIG_BOOTP_HOSTNAME


 /*
  * Command line configuration.
  */
 #include <config_cmd_default.h>

 #define CONFIG_CMD_PING
 #define CONFIG_CMD_I2C
 #define CONFIG_CMD_MII
 #define CONFIG_CMD_ELF
 #define CONFIG_CMD_IRQ
 #define CONFIG_CMD_SETEXPR
 #define CONFIG_CMD_REGINFO

 #if defined(CONFIG_PCI)
     #define CONFIG_CMD_PCI
 #endif


 #undef CONFIG_WATCHDOG			/* watchdog disabled */

 /*
  * Miscellaneous configurable options
  */
 #define CONFIG_SYS_LONGHELP			/* undef to save memory	*/
 #define CONFIG_CMDLINE_EDITING			/* Command-line editing */
 #define CONFIG_AUTO_COMPLETE			/* add autocompletion support */
 #define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size */
 #else
 #define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size */
 #endif
 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
 #define CONFIG_SYS_MAXARGS	16		/* max number of command args */
 #define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size */

 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 64 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
 #define CONFIG_SYS_BOOTMAPSZ	(64 << 20)	/* Initial Memory map for Linux*/
 #define CONFIG_SYS_BOOTM_LEN	(64 << 20)	/* Increase max gunzip size */

 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
 #define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
 #endif

 /*
  * Environment Configuration
  */

 /* The mac addresses for all ethernet interface */
 #if defined(CONFIG_TSEC_ENET)
 #define CONFIG_HAS_ETH0
 #define CONFIG_ETHADDR	 00:E0:0C:00:00:FD
 #define CONFIG_HAS_ETH1
 #define CONFIG_ETH1ADDR	 00:E0:0C:00:01:FD
 #define CONFIG_HAS_ETH2
 #define CONFIG_ETH2ADDR	 00:E0:0C:00:02:FD
 #define CONFIG_HAS_ETH3
 #define CONFIG_ETH3ADDR	 00:E0:0C:00:03:FD
 #endif

 #define CONFIG_IPADDR	 192.168.1.253

 #define CONFIG_HOSTNAME	 unknown
 #define CONFIG_ROOTPATH	 "/nfsroot"
 #define CONFIG_BOOTFILE "8548cds/uImage.uboot"
 #define CONFIG_UBOOTPATH	8548cds/u-boot.bin	/* TFTP server */

 #define CONFIG_SERVERIP	 192.168.1.1
 #define CONFIG_GATEWAYIP 192.168.1.1
 #define CONFIG_NETMASK	 255.255.255.0

 #define CONFIG_LOADADDR	1000000	/*default location for tftp and bootm*/

 #define CONFIG_BOOTDELAY 10	/* -1 disables auto-boot */
 #undef	CONFIG_BOOTARGS		/* the boot command will set bootargs*/

 #define CONFIG_BAUDRATE	115200

 #define	CONFIG_EXTRA_ENV_SETTINGS		\
 	"hwconfig=fsl_ddr:ecc=off\0"		\
 	"netdev=eth0\0"				\
 	"uboot=" __stringify(CONFIG_UBOOTPATH) "\0"	\
 	"tftpflash=tftpboot $loadaddr $uboot; "	\
 		"protect off " __stringify(CONFIG_SYS_TEXT_BASE)	\
 			" +$filesize; "	\
 		"erase " __stringify(CONFIG_SYS_TEXT_BASE)		\
 			" +$filesize; "	\
 		"cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE)	\
 			" $filesize; "	\
 		"protect on " __stringify(CONFIG_SYS_TEXT_BASE)		\
 			" +$filesize; "	\
 		"cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE)	\
 			" $filesize\0"	\
 	"consoledev=ttyS1\0"			\
 	"ramdiskaddr=2000000\0"			\
 	"ramdiskfile=ramdisk.uboot\0"		\
 	"fdtaddr=c00000\0"			\
 	"fdtfile=mpc8548cds.dtb\0"

 #define CONFIG_NFSBOOTCOMMAND						\
    "setenv bootargs root=/dev/nfs rw "					\
       "nfsroot=$serverip:$rootpath "					\
       "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
       "console=$consoledev,$baudrate $othbootargs;"			\
    "tftp $loadaddr $bootfile;"						\
    "tftp $fdtaddr $fdtfile;"						\
    "bootm $loadaddr - $fdtaddr"


 #define CONFIG_RAMBOOTCOMMAND \
    "setenv bootargs root=/dev/ram rw "					\
       "console=$consoledev,$baudrate $othbootargs;"			\
    "tftp $ramdiskaddr $ramdiskfile;"					\
    "tftp $loadaddr $bootfile;"						\
    "tftp $fdtaddr $fdtfile;"						\
    "bootm $loadaddr $ramdiskaddr $fdtaddr"

 #define CONFIG_BOOTCOMMAND	CONFIG_NFSBOOTCOMMAND

 #endif	/* __CONFIG_H */
	/*
	* Copyright 2004, 2007, 2010-2011 Freescale Semiconductor.
	*
	* SPDX-License-Identifier: GPL-2.0+
	*/

	/*
	* mpc8548cds board configuration file
	*
	* Please refer to doc/README.mpc85xxcds for more info.
	*
	*/
	#ifndef __CONFIG_H
	#define __CONFIG_H

	#ifdef CONFIG_36BIT
	#define CONFIG_PHYS_64BIT
	#endif

	/* High Level Configuration Options */
	#define CONFIG_BOOKE 1 /* BOOKE */
	#define CONFIG_E500 1 /* BOOKE e500 family */
	#define CONFIG_MPC85xx 1 /* MPC8540/60/55/41/48 */
	#define CONFIG_MPC8548 1 /* MPC8548 specific */
	#define CONFIG_MPC8548CDS 1 /* MPC8548CDS board specific */

	#ifndef CONFIG_SYS_TEXT_BASE
	#define CONFIG_SYS_TEXT_BASE 0xfff80000
	#endif

	#define CONFIG_SYS_SRIO
	#define CONFIG_SRIO1 /* SRIO port 1 */

	#define CONFIG_PCI /* enable any pci type devices */
	#define CONFIG_PCI1 /* PCI controller 1 */
	#define CONFIG_PCIE1 /* PCIE controler 1 (slot 1) */
	#undef CONFIG_PCI2
	#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */
	#define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */
	#define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */
	#define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */

	#define CONFIG_TSEC_ENET /* tsec ethernet support */
	#define CONFIG_ENV_OVERWRITE
	#define CONFIG_INTERRUPTS /* enable pci, srio, ddr interrupts */
	#define CONFIG_FSL_LAW 1 /* Use common FSL init code */

	#define CONFIG_FSL_VIA

	#ifndef __ASSEMBLY__
	extern unsigned long get_clock_freq(void);
	#endif
	#define CONFIG_SYS_CLK_FREQ get_clock_freq() /* sysclk for MPC85xx */

	/*
	* These can be toggled for performance analysis, otherwise use default.
	*/
	#define CONFIG_L2_CACHE /* toggle L2 cache */
	#define CONFIG_BTB /* toggle branch predition */

	/*
	* Only possible on E500 Version 2 or newer cores.
	*/
	#define CONFIG_ENABLE_36BIT_PHYS 1

	#ifdef CONFIG_PHYS_64BIT
	#define CONFIG_ADDR_MAP
	#define CONFIG_SYS_NUM_ADDR_MAP 16 /* number of TLB1 entries */
	#endif

	#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */
	#define CONFIG_SYS_MEMTEST_END 0x00400000

	#define CONFIG_SYS_CCSRBAR 0xe0000000
	#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR

	/* DDR Setup */
	#define CONFIG_SYS_FSL_DDR2
	#undef CONFIG_FSL_DDR_INTERACTIVE
	#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
	#define CONFIG_DDR_SPD

	#define CONFIG_DDR_ECC
	#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */
	#define CONFIG_MEM_INIT_VALUE 0xDeadBeef

	#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/
	#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE

	#define CONFIG_NUM_DDR_CONTROLLERS 1
	#define CONFIG_DIMM_SLOTS_PER_CTLR 1
	#define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR)

	/* I2C addresses of SPD EEPROMs */
	#define SPD_EEPROM_ADDRESS 0x51 /* CTLR 0 DIMM 0 */

	/* Make sure required options are set */
	#ifndef CONFIG_SPD_EEPROM
	#error ("CONFIG_SPD_EEPROM is required")
	#endif

	#undef CONFIG_CLOCKS_IN_MHZ
	/*
	* Physical Address Map
	*
	* 32bit:
	* 0x0000_0000 0x7fff_ffff DDR 2G cacheable
	* 0x8000_0000 0x9fff_ffff PCI1 MEM 512M cacheable
	* 0xa000_0000 0xbfff_ffff PCIe MEM 512M cacheable
	* 0xc000_0000 0xdfff_ffff RapidIO 512M cacheable
	* 0xe000_0000 0xe00f_ffff CCSR 1M non-cacheable
	* 0xe200_0000 0xe20f_ffff PCI1 IO 1M non-cacheable
	* 0xe300_0000 0xe30f_ffff PCIe IO 1M non-cacheable
	* 0xf000_0000 0xf3ff_ffff SDRAM 64M cacheable
	* 0xf800_0000 0xf80f_ffff NVRAM/CADMUS 1M non-cacheable
	* 0xff00_0000 0xff7f_ffff FLASH (2nd bank) 8M non-cacheable
	* 0xff80_0000 0xffff_ffff FLASH (boot bank) 8M non-cacheable
	*
	* 36bit:
	* 0x00000_0000 0x07fff_ffff DDR 2G cacheable
	* 0xc0000_0000 0xc1fff_ffff PCI1 MEM 512M cacheable
	* 0xc2000_0000 0xc3fff_ffff PCIe MEM 512M cacheable
	* 0xc4000_0000 0xc5fff_ffff RapidIO 512M cacheable
	* 0xfe000_0000 0xfe00f_ffff CCSR 1M non-cacheable
	* 0xfe200_0000 0xfe20f_ffff PCI1 IO 1M non-cacheable
	* 0xfe300_0000 0xfe30f_ffff PCIe IO 1M non-cacheable
	* 0xff000_0000 0xff3ff_ffff SDRAM 64M cacheable
	* 0xff800_0000 0xff80f_ffff NVRAM/CADMUS 1M non-cacheable
	* 0xfff00_0000 0xfff7f_ffff FLASH (2nd bank) 8M non-cacheable
	* 0xfff80_0000 0xfffff_ffff FLASH (boot bank) 8M non-cacheable
	*
	*/


	/*
	* Local Bus Definitions
	*/

	/*
	* FLASH on the Local Bus
	* Two banks, 8M each, using the CFI driver.
	* Boot from BR0/OR0 bank at 0xff00_0000
	* Alternate BR1/OR1 bank at 0xff80_0000
	*
	* BR0, BR1:
	* Base address 0 = 0xff00_0000 = BR0[0:16] = 1111 1111 0000 0000 0
	* Base address 1 = 0xff80_0000 = BR1[0:16] = 1111 1111 1000 0000 0
	* Port Size = 16 bits = BRx[19:20] = 10
	* Use GPCM = BRx[24:26] = 000
	* Valid = BRx[31] = 1
	*
	* 0 4 8 12 16 20 24 28
	* 1111 1111 1000 0000 0001 0000 0000 0001 = ff801001 BR0
	* 1111 1111 0000 0000 0001 0000 0000 0001 = ff001001 BR1
	*
	* OR0, OR1:
	* Addr Mask = 8M = ORx[0:16] = 1111 1111 1000 0000 0
	* Reserved ORx[17:18] = 11, confusion here?
	* CSNT = ORx[20] = 1
	* ACS = half cycle delay = ORx[21:22] = 11
	* SCY = 6 = ORx[24:27] = 0110
	* TRLX = use relaxed timing = ORx[29] = 1
	* EAD = use external address latch delay = OR[31] = 1
	*
	* 0 4 8 12 16 20 24 28
	* 1111 1111 1000 0000 0110 1110 0110 0101 = ff806e65 ORx
	*/

	#define CONFIG_SYS_FLASH_BASE 0xff000000 /* start of FLASH 16M */
	#ifdef CONFIG_PHYS_64BIT
	#define CONFIG_SYS_FLASH_BASE_PHYS 0xfff000000ull
	#else
	#define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE
	#endif

	#define CONFIG_SYS_BR0_PRELIM \
	(BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS + 0x800000) \| BR_PS_16 \| BR_V)
	#define CONFIG_SYS_BR1_PRELIM \
	(BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \| BR_PS_16 \| BR_V)

	#define CONFIG_SYS_OR0_PRELIM 0xff806e65
	#define CONFIG_SYS_OR1_PRELIM 0xff806e65

	#define CONFIG_SYS_FLASH_BANKS_LIST \
	{CONFIG_SYS_FLASH_BASE_PHYS + 0x800000, CONFIG_SYS_FLASH_BASE_PHYS}
	#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */
	#define CONFIG_SYS_MAX_FLASH_SECT 128 /* sectors per device */
	#undef CONFIG_SYS_FLASH_CHECKSUM
	#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
	#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */

	#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */

	#define CONFIG_FLASH_CFI_DRIVER
	#define CONFIG_SYS_FLASH_CFI
	#define CONFIG_SYS_FLASH_EMPTY_INFO

	#define CONFIG_HWCONFIG /* enable hwconfig */

	/*
	* SDRAM on the Local Bus
	*/
	#define CONFIG_SYS_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */
	#ifdef CONFIG_PHYS_64BIT
	#define CONFIG_SYS_LBC_SDRAM_BASE_PHYS 0xff0000000ull
	#else
	#define CONFIG_SYS_LBC_SDRAM_BASE_PHYS CONFIG_SYS_LBC_SDRAM_BASE
	#endif
	#define CONFIG_SYS_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */

	/*
	* Base Register 2 and Option Register 2 configure SDRAM.
	* The SDRAM base address, CONFIG_SYS_LBC_SDRAM_BASE, is 0xf0000000.
	*
	* For BR2, need:
	* Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0
	* port-size = 32-bits = BR2[19:20] = 11
	* no parity checking = BR2[21:22] = 00
	* SDRAM for MSEL = BR2[24:26] = 011
	* Valid = BR[31] = 1
	*
	* 0 4 8 12 16 20 24 28
	* 1111 0000 0000 0000 0001 1000 0110 0001 = f0001861
	*
	* FIXME: CONFIG_SYS_LBC_SDRAM_BASE should be masked and OR'ed into
	* FIXME: the top 17 bits of BR2.
	*/

	#define CONFIG_SYS_BR2_PRELIM \
	(BR_PHYS_ADDR(CONFIG_SYS_LBC_SDRAM_BASE_PHYS) \
	\| BR_PS_32 \| (3<<BR_MSEL_SHIFT) \| BR_V)

	/*
	* The SDRAM size in MB, CONFIG_SYS_LBC_SDRAM_SIZE, is 64.
	*
	* For OR2, need:
	* 64MB mask for AM, OR2[0:7] = 1111 1100
	* XAM, OR2[17:18] = 11
	* 9 columns OR2[19-21] = 010
	* 13 rows OR2[23-25] = 100
	* EAD set for extra time OR[31] = 1
	*
	* 0 4 8 12 16 20 24 28
	* 1111 1100 0000 0000 0110 1001 0000 0001 = fc006901
	*/

	#define CONFIG_SYS_OR2_PRELIM 0xfc006901

	#define CONFIG_SYS_LBC_LCRR 0x00030004 /* LB clock ratio reg */
	#define CONFIG_SYS_LBC_LBCR 0x00000000 /* LB config reg */
	#define CONFIG_SYS_LBC_LSRT 0x20000000 /* LB sdram refresh timer */
	#define CONFIG_SYS_LBC_MRTPR 0x00000000 /* LB refresh timer prescal*/

	/*
	* Common settings for all Local Bus SDRAM commands.
	* At run time, either BSMA1516 (for CPU 1.1)
	* or BSMA1617 (for CPU 1.0) (old)
	* is OR'ed in too.
	*/
	#define CONFIG_SYS_LBC_LSDMR_COMMON ( LSDMR_RFCR16 \
	\| LSDMR_PRETOACT7 \
	\| LSDMR_ACTTORW7 \
	\| LSDMR_BL8 \
	\| LSDMR_WRC4 \
	\| LSDMR_CL3 \
	\| LSDMR_RFEN \
	)

	/*
	* The CADMUS registers are connected to CS3 on CDS.
	* The new memory map places CADMUS at 0xf8000000.
	*
	* For BR3, need:
	* Base address of 0xf8000000 = BR[0:16] = 1111 1000 0000 0000 0
	* port-size = 8-bits = BR[19:20] = 01
	* no parity checking = BR[21:22] = 00
	* GPMC for MSEL = BR[24:26] = 000
	* Valid = BR[31] = 1
	*
	* 0 4 8 12 16 20 24 28
	* 1111 1000 0000 0000 0000 1000 0000 0001 = f8000801
	*
	* For OR3, need:
	* 1 MB mask for AM, OR[0:16] = 1111 1111 1111 0000 0
	* disable buffer ctrl OR[19] = 0
	* CSNT OR[20] = 1
	* ACS OR[21:22] = 11
	* XACS OR[23] = 1
	* SCY 15 wait states OR[24:27] = 1111 max is suboptimal but safe
	* SETA OR[28] = 0
	* TRLX OR[29] = 1
	* EHTR OR[30] = 1
	* EAD extra time OR[31] = 1
	*
	* 0 4 8 12 16 20 24 28
	* 1111 1111 1111 0000 0000 1111 1111 0111 = fff00ff7
	*/

	#define CONFIG_FSL_CADMUS

	#define CADMUS_BASE_ADDR 0xf8000000
	#ifdef CONFIG_PHYS_64BIT
	#define CADMUS_BASE_ADDR_PHYS 0xff8000000ull
	#else
	#define CADMUS_BASE_ADDR_PHYS CADMUS_BASE_ADDR
	#endif
	#define CONFIG_SYS_BR3_PRELIM \
	(BR_PHYS_ADDR(CADMUS_BASE_ADDR_PHYS) \| BR_PS_8 \| BR_V)
	#define CONFIG_SYS_OR3_PRELIM 0xfff00ff7

	#define CONFIG_SYS_INIT_RAM_LOCK 1
	#define CONFIG_SYS_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */
	#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in RAM */

	#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
	#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET

	#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
	#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */

	/* Serial Port */
	#define CONFIG_CONS_INDEX 2
	#define CONFIG_SYS_NS16550
	#define CONFIG_SYS_NS16550_SERIAL
	#define CONFIG_SYS_NS16550_REG_SIZE 1
	#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)

	#define CONFIG_SYS_BAUDRATE_TABLE \
	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}

	#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
	#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)

	/* Use the HUSH parser */
	#define CONFIG_SYS_HUSH_PARSER

	/* pass open firmware flat tree */
	#define CONFIG_OF_LIBFDT 1
	#define CONFIG_OF_BOARD_SETUP 1
	#define CONFIG_OF_STDOUT_VIA_ALIAS 1

	/*
	* I2C
	*/
	#define CONFIG_SYS_I2C
	#define CONFIG_SYS_I2C_FSL
	#define CONFIG_SYS_FSL_I2C_SPEED 400000
	#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
	#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
	#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} }

	/* EEPROM */
	#define CONFIG_ID_EEPROM
	#define CONFIG_SYS_I2C_EEPROM_CCID
	#define CONFIG_SYS_ID_EEPROM
	#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
	#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2

	/*
	* General PCI
	* Memory space is mapped 1-1, but I/O space must start from 0.
	*/
	#define CONFIG_SYS_PCI1_MEM_VIRT 0x80000000
	#ifdef CONFIG_PHYS_64BIT
	#define CONFIG_SYS_PCI1_MEM_BUS 0xe0000000
	#define CONFIG_SYS_PCI1_MEM_PHYS 0xc00000000ull
	#else
	#define CONFIG_SYS_PCI1_MEM_BUS 0x80000000
	#define CONFIG_SYS_PCI1_MEM_PHYS 0x80000000
	#endif
	#define CONFIG_SYS_PCI1_MEM_SIZE 0x20000000 /* 512M */
	#define CONFIG_SYS_PCI1_IO_VIRT 0xe2000000
	#define CONFIG_SYS_PCI1_IO_BUS 0x00000000
	#ifdef CONFIG_PHYS_64BIT
	#define CONFIG_SYS_PCI1_IO_PHYS 0xfe2000000ull
	#else
	#define CONFIG_SYS_PCI1_IO_PHYS 0xe2000000
	#endif
	#define CONFIG_SYS_PCI1_IO_SIZE 0x00100000 /* 1M */

	#ifdef CONFIG_PCIE1
	#define CONFIG_SYS_PCIE1_NAME "Slot"
	#define CONFIG_SYS_PCIE1_MEM_VIRT 0xa0000000
	#ifdef CONFIG_PHYS_64BIT
	#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000
	#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc20000000ull
	#else
	#define CONFIG_SYS_PCIE1_MEM_BUS 0xa0000000
	#define CONFIG_SYS_PCIE1_MEM_PHYS 0xa0000000
	#endif
	#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
	#define CONFIG_SYS_PCIE1_IO_VIRT 0xe3000000
	#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
	#ifdef CONFIG_PHYS_64BIT
	#define CONFIG_SYS_PCIE1_IO_PHYS 0xfe3000000ull
	#else
	#define CONFIG_SYS_PCIE1_IO_PHYS 0xe3000000
	#endif
	#define CONFIG_SYS_PCIE1_IO_SIZE 0x00100000 /* 1M */
	#endif

	/*
	* RapidIO MMU
	*/
	#define CONFIG_SYS_SRIO1_MEM_VIRT 0xc0000000
	#ifdef CONFIG_PHYS_64BIT
	#define CONFIG_SYS_SRIO1_MEM_PHYS 0xc40000000ull
	#else
	#define CONFIG_SYS_SRIO1_MEM_PHYS 0xc0000000
	#endif
	#define CONFIG_SYS_SRIO1_MEM_SIZE 0x20000000 /* 512M */

	#ifdef CONFIG_LEGACY
	#define BRIDGE_ID 17
	#define VIA_ID 2
	#else
	#define BRIDGE_ID 28
	#define VIA_ID 4
	#endif

	#if defined(CONFIG_PCI)

	#define CONFIG_PCI_PNP /* do pci plug-and-play */

	#undef CONFIG_EEPRO100
	#undef CONFIG_TULIP
	#define CONFIG_E1000 /* Define e1000 pci Ethernet card */

	#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */

	#endif /* CONFIG_PCI */


	#if defined(CONFIG_TSEC_ENET)

	#define CONFIG_MII 1 /* MII PHY management */
	#define CONFIG_TSEC1 1
	#define CONFIG_TSEC1_NAME "eTSEC0"
	#define CONFIG_TSEC2 1
	#define CONFIG_TSEC2_NAME "eTSEC1"
	#define CONFIG_TSEC3 1
	#define CONFIG_TSEC3_NAME "eTSEC2"
	#define CONFIG_TSEC4
	#define CONFIG_TSEC4_NAME "eTSEC3"
	#undef CONFIG_MPC85XX_FEC

	#define CONFIG_PHY_MARVELL

	#define TSEC1_PHY_ADDR 0
	#define TSEC2_PHY_ADDR 1
	#define TSEC3_PHY_ADDR 2
	#define TSEC4_PHY_ADDR 3

	#define TSEC1_PHYIDX 0
	#define TSEC2_PHYIDX 0
	#define TSEC3_PHYIDX 0
	#define TSEC4_PHYIDX 0
	#define TSEC1_FLAGS TSEC_GIGABIT
	#define TSEC2_FLAGS TSEC_GIGABIT
	#define TSEC3_FLAGS (TSEC_GIGABIT \| TSEC_REDUCED)
	#define TSEC4_FLAGS (TSEC_GIGABIT \| TSEC_REDUCED)

	/* Options are: eTSEC[0-3] */
	#define CONFIG_ETHPRIME "eTSEC0"
	#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
	#endif /* CONFIG_TSEC_ENET */

	/*
	* Environment
	*/
	#define CONFIG_ENV_IS_IN_FLASH 1
	#if CONFIG_SYS_MONITOR_BASE > 0xfff80000
	#define CONFIG_ENV_ADDR 0xfff80000
	#else
	#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
	#endif
	#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K for env */
	#define CONFIG_ENV_SIZE 0x2000

	#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
	#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */

	/*
	* BOOTP options
	*/
	#define CONFIG_BOOTP_BOOTFILESIZE
	#define CONFIG_BOOTP_BOOTPATH
	#define CONFIG_BOOTP_GATEWAY
	#define CONFIG_BOOTP_HOSTNAME


	/*
	* Command line configuration.
	*/
	#include <config_cmd_default.h>

	#define CONFIG_CMD_PING
	#define CONFIG_CMD_I2C
	#define CONFIG_CMD_MII
	#define CONFIG_CMD_ELF
	#define CONFIG_CMD_IRQ
	#define CONFIG_CMD_SETEXPR
	#define CONFIG_CMD_REGINFO

	#if defined(CONFIG_PCI)
	#define CONFIG_CMD_PCI
	#endif


	#undef CONFIG_WATCHDOG /* watchdog disabled */

	/*
	* Miscellaneous configurable options
	*/
	#define CONFIG_SYS_LONGHELP /* undef to save memory */
	#define CONFIG_CMDLINE_EDITING /* Command-line editing */
	#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
	#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
	#if defined(CONFIG_CMD_KGDB)
	#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
	#else
	#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
	#endif
	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
	#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */

	/*
	* For booting Linux, the board info and command line data
	* have to be in the first 64 MB of memory, since this is
	* the maximum mapped by the Linux kernel during initialization.
	*/
	#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux*/
	#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */

	#if defined(CONFIG_CMD_KGDB)
	#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
	#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
	#endif

	/*
	* Environment Configuration
	*/

	/* The mac addresses for all ethernet interface */
	#if defined(CONFIG_TSEC_ENET)
	#define CONFIG_HAS_ETH0
	#define CONFIG_ETHADDR 00:E0:0C:00:00:FD
	#define CONFIG_HAS_ETH1
	#define CONFIG_ETH1ADDR 00:E0:0C:00:01:FD
	#define CONFIG_HAS_ETH2
	#define CONFIG_ETH2ADDR 00:E0:0C:00:02:FD
	#define CONFIG_HAS_ETH3
	#define CONFIG_ETH3ADDR 00:E0:0C:00:03:FD
	#endif

	#define CONFIG_IPADDR 192.168.1.253

	#define CONFIG_HOSTNAME unknown
	#define CONFIG_ROOTPATH "/nfsroot"
	#define CONFIG_BOOTFILE "8548cds/uImage.uboot"
	#define CONFIG_UBOOTPATH 8548cds/u-boot.bin /* TFTP server */

	#define CONFIG_SERVERIP 192.168.1.1
	#define CONFIG_GATEWAYIP 192.168.1.1
	#define CONFIG_NETMASK 255.255.255.0

	#define CONFIG_LOADADDR 1000000 /default location for tftp and bootm/

	#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */
	#undef CONFIG_BOOTARGS /* the boot command will set bootargs*/

	#define CONFIG_BAUDRATE 115200

	#define CONFIG_EXTRA_ENV_SETTINGS \
	"hwconfig=fsl_ddr:ecc=off\0" \
	"netdev=eth0\0" \
	"uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \
	"tftpflash=tftpboot $loadaddr $uboot; " \
	"protect off " __stringify(CONFIG_SYS_TEXT_BASE) \
	" +$filesize; " \
	"erase " __stringify(CONFIG_SYS_TEXT_BASE) \
	" +$filesize; " \
	"cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \
	" $filesize; " \
	"protect on " __stringify(CONFIG_SYS_TEXT_BASE) \
	" +$filesize; " \
	"cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \
	" $filesize\0" \
	"consoledev=ttyS1\0" \
	"ramdiskaddr=2000000\0" \
	"ramdiskfile=ramdisk.uboot\0" \
	"fdtaddr=c00000\0" \
	"fdtfile=mpc8548cds.dtb\0"

	#define CONFIG_NFSBOOTCOMMAND \
	"setenv bootargs root=/dev/nfs rw " \
	"nfsroot=$serverip:$rootpath " \
	"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
	"console=$consoledev,$baudrate $othbootargs;" \
	"tftp $loadaddr $bootfile;" \
	"tftp $fdtaddr $fdtfile;" \
	"bootm $loadaddr - $fdtaddr"


	#define CONFIG_RAMBOOTCOMMAND \
	"setenv bootargs root=/dev/ram rw " \
	"console=$consoledev,$baudrate $othbootargs;" \
	"tftp $ramdiskaddr $ramdiskfile;" \
	"tftp $loadaddr $bootfile;" \
	"tftp $fdtaddr $fdtfile;" \
	"bootm $loadaddr $ramdiskaddr $fdtaddr"

	#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND

	#endif /* __CONFIG_H */