include/configs/MERGERBOX.h - github/trini/u-boot - Gitiles

 /*
  * Copyright (C) 2007 Freescale Semiconductor, Inc.
  *
  * Copyright (C) 2011 Matrix Vision GmbH
  * Andre Schwarz <andre.schwarz@matrix-vision.de>
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */

 #ifndef __CONFIG_H
 #define __CONFIG_H

 #include <version.h>

 /*
  * High Level Configuration Options
  */
 #define CONFIG_E300	1
 #define CONFIG_MPC83xx	1
 #define CONFIG_MPC837x	1
 #define CONFIG_MPC8377	1

 #define CONFIG_SYS_TEXT_BASE	0xFC000000

 #define CONFIG_PCI	1
 #define CONFIG_PCI_INDIRECT_BRIDGE 1

 #define	CONFIG_MASK_AER_AO
 #define CONFIG_DISPLAY_AER_FULL

 #define CONFIG_MISC_INIT_R

 /*
  * On-board devices
  */
 #define CONFIG_TSEC_ENET

 /*
  * System Clock Setup
  */
 #define CONFIG_83XX_CLKIN	66666667 /* in Hz */
 #define CONFIG_PCIE
 #define CONFIG_83XX_GENERIC_PCIE_REGISTER_HOSES
 #define CONFIG_SYS_CLK_FREQ	CONFIG_83XX_CLKIN

 /*
  * Hardware Reset Configuration Word stored in EEPROM.
  */
 #define CONFIG_SYS_HRCW_LOW	0
 #define CONFIG_SYS_HRCW_HIGH	0

 /* Arbiter Configuration Register */
 #define CONFIG_SYS_ACR_PIPE_DEP	3
 #define CONFIG_SYS_ACR_RPTCNT	3

 /* System Priority Control Regsiter */
 #define CONFIG_SYS_SPCR_TSECEP	3

 /* System Clock Configuration Register */
 #define CONFIG_SYS_SCCR_TSEC1CM		3
 #define CONFIG_SYS_SCCR_TSEC2CM		0
 #define CONFIG_SYS_SCCR_SDHCCM		3
 #define CONFIG_SYS_SCCR_ENCCM		3 /* also clock for I2C-1 */
 #define CONFIG_SYS_SCCR_USBDRCM		CONFIG_SYS_SCCR_ENCCM /* must match */
 #define CONFIG_SYS_SCCR_PCIEXP1CM	3
 #define CONFIG_SYS_SCCR_PCIEXP2CM	3
 #define CONFIG_SYS_SCCR_PCICM		1
 #define CONFIG_SYS_SCCR_SATACM		0xFF

 /*
  * System IO Config
  */
 #define CONFIG_SYS_SICRH	0x087c0000
 #define CONFIG_SYS_SICRL	0x40000000

 /*
  * Output Buffer Impedance
  */
 #define CONFIG_SYS_OBIR		0x30000000

 /*
  * IMMR new address
  */
 #define CONFIG_SYS_IMMR		0xE0000000

 /*
  * DDR Setup
  */
 #define CONFIG_SYS_DDR_BASE		0x00000000
 #define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_BASE
 #define CONFIG_SYS_DDR_SDRAM_BASE	CONFIG_SYS_DDR_BASE
 #define CONFIG_SYS_83XX_DDR_USES_CS0

 #define CONFIG_SYS_DDRCDR_VALUE		(DDRCDR_EN | DDRCDR_PZ_HIZ |\
 					 DDRCDR_NZ_HIZ | DDRCDR_ODT |\
 					 DDRCDR_Q_DRN)

 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL	DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05

 #define CONFIG_SYS_DDR_MODE_WEAK
 #define CONFIG_SYS_DDR_WRITE_DATA_DELAY	2
 #define CONFIG_SYS_DDR_CPO	0x1f

 /* SPD table located at offset 0x20 in extended adressing ROM
  * used for HRCW fetch after power-on reset
  */
 #define	CONFIG_SPD_EEPROM
 #define	SPD_EEPROM_ADDRESS	0x50
 #define	SPD_EEPROM_OFFSET	0x20
 #define	SPD_EEPROM_ADDR_LEN	2

 /*
  * The reserved memory
  */
 #define CONFIG_SYS_MONITOR_BASE		CONFIG_SYS_TEXT_BASE
 #define CONFIG_SYS_MONITOR_LEN		(512*1024)
 #define CONFIG_SYS_MALLOC_LEN		(512*1024)

 /*
  * Initial RAM Base Address Setup
  */
 #define CONFIG_SYS_INIT_RAM_LOCK	1
 #define CONFIG_SYS_INIT_RAM_ADDR	0xE6000000 /* Initial RAM address */
 #define CONFIG_SYS_INIT_RAM_SIZE	0x1000 /* End of used area in RAM */
 #define CONFIG_SYS_GBL_DATA_SIZE	0x100 /* num bytes initial data */
 #define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE -\
 					 CONFIG_SYS_GBL_DATA_SIZE)

 /*
  * Local Bus Configuration & Clock Setup
  */
 #define CONFIG_SYS_LCRR_DBYP	LCRR_DBYP
 #define CONFIG_SYS_LCRR_CLKDIV	LCRR_CLKDIV_8
 #define CONFIG_SYS_LBC_LBCR	0x00000000
 #define CONFIG_FSL_ELBC		1

 /*
  * FLASH on the Local Bus
  */
 #define CONFIG_SYS_FLASH_CFI
 #define CONFIG_FLASH_CFI_DRIVER
 #define CONFIG_SYS_FLASH_CFI_WIDTH	FLASH_CFI_16BIT

 #define CONFIG_SYS_FLASH_BASE		CONFIG_SYS_TEXT_BASE
 #define CONFIG_SYS_FLASH_SIZE		64

 #define CONFIG_SYS_LBLAWBAR0_PRELIM	CONFIG_SYS_FLASH_BASE
 #define CONFIG_SYS_LBLAWAR0_PRELIM	(LBLAWAR_EN | LBLAWAR_64MB)

 #define CONFIG_SYS_BR0_PRELIM	(CONFIG_SYS_FLASH_BASE | BR_PS_16 |\
 				 BR_MS_GPCM | BR_V)
 #define CONFIG_SYS_OR0_PRELIM	(CONFIG_SYS_FLASH_BASE | OR_UPM_XAM |\
 				 OR_GPCM_CSNT | OR_GPCM_ACS_DIV2 |\
 				 OR_GPCM_XACS | OR_GPCM_SCY_15 |\
 				 OR_GPCM_TRLX_SET | OR_GPCM_EHTR_SET |\
 				 OR_GPCM_EAD)

 #define CONFIG_SYS_MAX_FLASH_BANKS	1
 #define CONFIG_SYS_MAX_FLASH_SECT	512

 #undef CONFIG_SYS_FLASH_CHECKSUM
 #define CONFIG_SYS_FLASH_ERASE_TOUT	120000 /* Flash Erase Timeout (ms) */
 #define CONFIG_SYS_FLASH_WRITE_TOUT	500 /* Flash Write Timeout (ms) */

 /*
  * NAND Flash on the Local Bus
  */
 #define CONFIG_MTD_NAND_VERIFY_WRITE	1
 #define CONFIG_SYS_MAX_NAND_DEVICE	1
 #define CONFIG_NAND_FSL_ELBC		1

 #define CONFIG_SYS_NAND_BASE	0xE0600000
 #define CONFIG_SYS_BR1_PRELIM	(CONFIG_SYS_NAND_BASE | BR_DECC_CHK_GEN |\
 				 BR_PS_8 | BR_MS_FCM | BR_V)
 #define CONFIG_SYS_OR1_PRELIM	(OR_AM_32KB | OR_FCM_BCTLD | OR_FCM_CST |\
 				 OR_FCM_CHT | OR_FCM_SCY_1 | OR_FCM_RST |\
 				 OR_FCM_TRLX | OR_FCM_EHTR)

 #define CONFIG_SYS_LBLAWBAR1_PRELIM	CONFIG_SYS_NAND_BASE
 #define CONFIG_SYS_LBLAWAR1_PRELIM	(LBLAWAR_EN | LBLAWAR_32KB)

 /*
  * Serial Port
  */
 #define CONFIG_CONS_INDEX	1
 #define CONFIG_SYS_NS16550
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE	1
 #define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)

 #define CONFIG_SYS_BAUDRATE_TABLE \
 	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}

 #define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_IMMR+0x4500)
 #define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_IMMR+0x4600)

 #define CONFIG_CONSOLE		ttyS0
 #define CONFIG_BAUDRATE		115200

 /* SERDES */
 #define CONFIG_FSL_SERDES
 #define CONFIG_FSL_SERDES1	0xe3000
 #define CONFIG_FSL_SERDES2	0xe3100

 /* Use the HUSH parser */
 #define CONFIG_SYS_HUSH_PARSER

 /* Pass open firmware flat tree */
 #define CONFIG_OF_LIBFDT	1
 #define CONFIG_OF_BOARD_SETUP	1
 #define CONFIG_OF_STDOUT_VIA_ALIAS 1

 /* I2C */
 #define CONFIG_SYS_I2C
 #define CONFIG_SYS_I2C_FSL
 #define CONFIG_SYS_FSL_I2C_SPEED	400000
 #define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
 #define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
 #define CONFIG_SYS_FSL_I2C2_SPEED	400000
 #define CONFIG_SYS_FSL_I2C2_SLAVE	0x7F
 #define CONFIG_SYS_FSL_I2C2_OFFSET	0x3100

 /*
  * General PCI
  * Addresses are mapped 1-1.
  */
 #define CONFIG_SYS_PCI_MEM_BASE		0x80000000
 #define CONFIG_SYS_PCI_MEM_PHYS		CONFIG_SYS_PCI_MEM_BASE
 #define CONFIG_SYS_PCI_MEM_SIZE		(256 << 20)
 #define CONFIG_SYS_PCI_MMIO_BASE	0x90000000
 #define CONFIG_SYS_PCI_MMIO_PHYS	CONFIG_SYS_PCI_MMIO_BASE
 #define CONFIG_SYS_PCI_MMIO_SIZE	(256 << 20)
 #define CONFIG_SYS_PCI_IO_BASE		0x00000000
 #define CONFIG_SYS_PCI_IO_PHYS		0xE0300000
 #define CONFIG_SYS_PCI_IO_SIZE		(1 << 20)

 #ifdef CONFIG_PCIE
 #define CONFIG_SYS_PCIE1_BASE		0xA0000000
 #define CONFIG_SYS_PCIE1_CFG_BASE	0xA0000000
 #define CONFIG_SYS_PCIE1_CFG_SIZE	(128 << 20)
 #define CONFIG_SYS_PCIE1_MEM_BASE	0xA8000000
 #define CONFIG_SYS_PCIE1_MEM_PHYS	0xA8000000
 #define CONFIG_SYS_PCIE1_MEM_SIZE	(256 << 20)
 #define CONFIG_SYS_PCIE1_IO_BASE	0x00000000
 #define CONFIG_SYS_PCIE1_IO_PHYS	0xB8000000
 #define CONFIG_SYS_PCIE1_IO_SIZE	(8 << 20)

 #define CONFIG_SYS_PCIE2_BASE		0xC0000000
 #define CONFIG_SYS_PCIE2_CFG_BASE	0xC0000000
 #define CONFIG_SYS_PCIE2_CFG_SIZE	(128 << 20)
 #define CONFIG_SYS_PCIE2_MEM_BASE	0xC8000000
 #define CONFIG_SYS_PCIE2_MEM_PHYS	0xC8000000
 #define CONFIG_SYS_PCIE2_MEM_SIZE	(256 << 20)
 #define CONFIG_SYS_PCIE2_IO_BASE	0x00000000
 #define CONFIG_SYS_PCIE2_IO_PHYS	0xD8000000
 #define CONFIG_SYS_PCIE2_IO_SIZE	(8 << 20)
 #endif

 #define CONFIG_PCI_PNP
 #define CONFIG_PCI_SCAN_SHOW
 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957	/* Freescale */

 /*
  * TSEC
  */
 #define CONFIG_GMII			/* MII PHY management */
 #define CONFIG_SYS_VSC8601_SKEWFIX
 #define	CONFIG_SYS_VSC8601_SKEW_TX	3
 #define	CONFIG_SYS_VSC8601_SKEW_RX	3

 #define CONFIG_TSEC1
 #define CONFIG_HAS_ETH0
 #define CONFIG_TSEC1_NAME		"TSEC0"
 #define CONFIG_SYS_TSEC1_OFFSET		0x24000
 #define TSEC1_PHY_ADDR			0x10
 #define TSEC1_FLAGS			(TSEC_GIGABIT | TSEC_REDUCED)
 #define TSEC1_PHYIDX			0

 #define CONFIG_ETHPRIME			"TSEC0"
 #define CONFIG_HAS_ETH0

 /*
  * SATA
  */
 #define CONFIG_LIBATA
 #define CONFIG_FSL_SATA

 #define CONFIG_SYS_SATA_MAX_DEVICE	2
 #define CONFIG_SATA1
 #define CONFIG_SYS_SATA1_OFFSET	0x18000
 #define CONFIG_SYS_SATA1	(CONFIG_SYS_IMMR + CONFIG_SYS_SATA1_OFFSET)
 #define CONFIG_SYS_SATA1_FLAGS	FLAGS_DMA
 #define CONFIG_SATA2
 #define CONFIG_SYS_SATA2_OFFSET	0x19000
 #define CONFIG_SYS_SATA2	(CONFIG_SYS_IMMR + CONFIG_SYS_SATA2_OFFSET)
 #define CONFIG_SYS_SATA2_FLAGS	FLAGS_DMA

 #define CONFIG_LBA48
 #define CONFIG_CMD_SATA
 #define CONFIG_DOS_PARTITION
 #define CONFIG_CMD_EXT2

 /*
  * BOOTP options
  */
 #define CONFIG_BOOTP_BOOTFILESIZE
 #define CONFIG_BOOTP_BOOTPATH
 #define CONFIG_BOOTP_GATEWAY
 #define CONFIG_BOOTP_HOSTNAME
 #define CONFIG_BOOTP_VENDOREX
 #define CONFIG_BOOTP_SUBNETMASK
 #define CONFIG_BOOTP_DNS
 #define CONFIG_BOOTP_DNS2
 #define CONFIG_BOOTP_NTPSERVER
 #define CONFIG_BOOTP_RANDOM_DELAY
 #define CONFIG_BOOTP_SEND_HOSTNAME

 /*
  * Command line configuration.
  */
 #include <config_cmd_default.h>

 #define CONFIG_CMD_ASKENV
 #define CONFIG_CMD_NAND
 #define CONFIG_CMD_PING
 #define CONFIG_CMD_EEPROM
 #define CONFIG_CMD_I2C
 #define CONFIG_CMD_MII
 #define CONFIG_CMD_PCI
 #define CONFIG_CMD_USB
 #define CONFIG_CMD_SPI
 #define CONFIG_CMD_DHCP
 #define CONFIG_CMD_UBI
 #define CONFIG_CMD_UBIFS
 #define CONFIG_CMD_MTDPARTS
 #define CONFIG_CMD_SATA

 #define CONFIG_CMD_EXT2
 #define CONFIG_CMD_FAT
 #define CONFIG_CMD_JFFS2

 #define CONFIG_RBTREE
 #define CONFIG_LZO

 #define CONFIG_MTD_DEVICE
 #define CONFIG_MTD_PARTITIONS

 #define CONFIG_FLASH_CFI_MTD
 #define MTDIDS_DEFAULT "nor0=NOR,nand0=NAND"
 #define MTDPARTS_DEFAULT "mtdparts=NOR:1M(u-boot),2M(FPGA);NAND:-(root)"

 #define CONFIG_FIT
 #define CONFIG_FIT_VERBOSE	1

 #define CONFIG_CMDLINE_EDITING	1
 #define CONFIG_AUTO_COMPLETE

 /*
  * Miscellaneous configurable options
  */
 #define CONFIG_SYS_LONGHELP
 #define CONFIG_SYS_LOAD_ADDR	0x2000000
 #define CONFIG_LOADADDR		0x4000000
 #define CONFIG_SYS_CBSIZE	256

 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
 #define CONFIG_SYS_MAXARGS	16
 #define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE

 #define CONFIG_LOADS_ECHO		1
 #define CONFIG_SYS_LOADS_BAUD_CHANGE	1

 #define CONFIG_SYS_MEMTEST_START	(60<<20)
 #define CONFIG_SYS_MEMTEST_END		(70<<20)

 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 256 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
 #define CONFIG_SYS_BOOTMAPSZ	(256 << 20) /* Initial Memory map for Linux */

 /*
  * Core HID Setup
  */
 #define CONFIG_SYS_HID0_INIT	0x000000000
 #define CONFIG_SYS_HID0_FINAL	(HID0_ENABLE_MACHINE_CHECK | \
 				 HID0_ENABLE_INSTRUCTION_CACHE)
 #define CONFIG_SYS_HID2		HID2_HBE

 /*
  * MMU Setup
  */
 #define CONFIG_HIGH_BATS	1

 /* DDR: cache cacheable */
 #define CONFIG_SYS_SDRAM	CONFIG_SYS_SDRAM_BASE

 #define CONFIG_SYS_IBAT0L	(CONFIG_SYS_SDRAM | BATL_PP_RW |\
 				 BATL_MEMCOHERENCE)
 #define CONFIG_SYS_IBAT0U	(CONFIG_SYS_SDRAM | BATU_BL_256M | BATU_VS |\
 				 BATU_VP)
 #define CONFIG_SYS_DBAT0L	CONFIG_SYS_IBAT0L
 #define CONFIG_SYS_DBAT0U	CONFIG_SYS_IBAT0U

 /* unused */
 #define CONFIG_SYS_IBAT1L	(0)
 #define CONFIG_SYS_IBAT1U	(0)
 #define CONFIG_SYS_DBAT1L	CONFIG_SYS_IBAT1L
 #define CONFIG_SYS_DBAT1U	CONFIG_SYS_IBAT1U

 /* IMMRBAR, PCI IO and NAND: cache-inhibit and guarded */
 #define CONFIG_SYS_IBAT2L	(CONFIG_SYS_IMMR | BATL_PP_RW |\
 				 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
 #define CONFIG_SYS_IBAT2U	(CONFIG_SYS_IMMR | BATU_BL_8M | BATU_VS |\
 				 BATU_VP)
 #define CONFIG_SYS_DBAT2L	CONFIG_SYS_IBAT2L
 #define CONFIG_SYS_DBAT2U	CONFIG_SYS_IBAT2U

 /* unused */
 #define CONFIG_SYS_IBAT3L	(0)
 #define CONFIG_SYS_IBAT3U	(0)
 #define CONFIG_SYS_DBAT3L	CONFIG_SYS_IBAT3L
 #define CONFIG_SYS_DBAT3U	CONFIG_SYS_IBAT3U

 /* FLASH: icache cacheable, but dcache-inhibit and guarded */
 #define CONFIG_SYS_IBAT4L	(CONFIG_SYS_FLASH_BASE | BATL_PP_RW |\
 				 BATL_MEMCOHERENCE)
 #define CONFIG_SYS_IBAT4U	(CONFIG_SYS_FLASH_BASE | BATU_BL_64M |\
 				 BATU_VS | BATU_VP)
 #define CONFIG_SYS_DBAT4L	(CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \
 				 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
 #define CONFIG_SYS_DBAT4U	CONFIG_SYS_IBAT4U

 /* Stack in dcache: cacheable, no memory coherence */
 #define CONFIG_SYS_IBAT5L	(CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW)
 #define CONFIG_SYS_IBAT5U	(CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K |\
 				 BATU_VS | BATU_VP)
 #define CONFIG_SYS_DBAT5L	CONFIG_SYS_IBAT5L
 #define CONFIG_SYS_DBAT5U	CONFIG_SYS_IBAT5U

 /* PCI MEM space: cacheable */
 #define CONFIG_SYS_IBAT6L	(CONFIG_SYS_PCI_MEM_PHYS | BATL_PP_RW |\
 				 BATL_MEMCOHERENCE)
 #define CONFIG_SYS_IBAT6U	(CONFIG_SYS_PCI_MEM_PHYS | BATU_BL_256M |\
 				 BATU_VS | BATU_VP)
 #define CONFIG_SYS_DBAT6L	CONFIG_SYS_IBAT6L
 #define CONFIG_SYS_DBAT6U	CONFIG_SYS_IBAT6U

 /* PCI MMIO space: cache-inhibit and guarded */
 #define CONFIG_SYS_IBAT7L	(CONFIG_SYS_PCI_MMIO_PHYS | BATL_PP_RW | \
 				 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
 #define CONFIG_SYS_IBAT7U	(CONFIG_SYS_PCI_MMIO_PHYS | BATU_BL_256M |\
 				 BATU_VS | BATU_VP)
 #define CONFIG_SYS_DBAT7L	CONFIG_SYS_IBAT7L
 #define CONFIG_SYS_DBAT7U	CONFIG_SYS_IBAT7U

 /*
  * I2C EEPROM settings
  */
 #define CONFIG_SYS_I2C_EEPROM_ADDR		0x50
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	6
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	10
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		2
 #define CONFIG_SYS_EEPROM_SIZE			0x4000

 /*
  * Environment Configuration
  */
 #define CONFIG_SYS_FLASH_PROTECTION
 #define CONFIG_ENV_OVERWRITE
 #define CONFIG_ENV_IS_IN_FLASH	1
 #define CONFIG_ENV_ADDR		0xFFD00000
 #define CONFIG_ENV_SECT_SIZE	0x20000
 #define CONFIG_ENV_SIZE		CONFIG_ENV_SECT_SIZE

 /*
  * Video
  */
 #define CONFIG_VIDEO
 #define CONFIG_VIDEO_SM501_PCI
 #define VIDEO_FB_LITTLE_ENDIAN
 #define CONFIG_CMD_BMP
 #define CONFIG_VIDEO_SM501
 #define CONFIG_VIDEO_SM501_32BPP
 #define CONFIG_VIDEO_SM501_FBMEM_OFFSET	0x10000
 #define CONFIG_CFB_CONSOLE
 #define CONFIG_VIDEO_LOGO
 #define CONFIG_VIDEO_BMP_LOGO
 #define CONFIG_VGA_AS_SINGLE_DEVICE
 #define CONFIG_SPLASH_SCREEN
 #define CONFIG_SYS_CONSOLE_IS_IN_ENV
 #define CONFIG_VIDEO_BMP_GZIP
 #define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE	(2 << 20)

 /*
  * SPI
  */
 #define CONFIG_MPC8XXX_SPI

 /*
  * USB
  */
 #define CONFIG_SYS_USB_HOST
 #define CONFIG_USB_EHCI
 #define CONFIG_USB_EHCI_FSL
 #define CONFIG_HAS_FSL_DR_USB
 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET

 #define CONFIG_USB_STORAGE
 #define CONFIG_USB_KEYBOARD
 /*
  *
  */
 #define CONFIG_BOOTDELAY	5
 #define CONFIG_AUTOBOOT_KEYED
 #define CONFIG_AUTOBOOT_STOP_STR	"s"
 #define CONFIG_ZERO_BOOTDELAY_CHECK
 #define CONFIG_RESET_TO_RETRY	1000

 #define MV_CI		"MergerBox"
 #define MV_VCI		"MergerBox"
 #define MV_FPGA_DATA	0xfc100000
 #define MV_FPGA_SIZE	0x00200000

 #define CONFIG_SHOW_BOOT_PROGRESS 1

 #define MV_KERNEL_ADDR_RAM	0x02800000
 #define MV_DTB_ADDR_RAM		0x00600000
 #define MV_INITRD_ADDR_RAM	0x01000000
 #define MV_FITADDR		0xfc300000
 #define	MV_SPLAH_ADDR		0xffe00000

 #define CONFIG_BOOTCOMMAND	"run i2c_init;if test ${boot_sqfs} -eq 1;"\
 				"then; run fitboot;else;run ubiboot;fi;"
 #define CONFIG_BOOTARGS		"console=ttyS0,115200n8"

 #define CONFIG_EXTRA_ENV_SETTINGS \
 	"console_nr=0\0"\
 	"stdin=serial\0"\
 	"stdout=serial\0"\
 	"stderr=serial\0"\
 	"boot_sqfs=1\0"\
 	"usb_dr_mode=host\0"\
 	"bootfile=MergerBox.fit\0"\
 	"baudrate=" __stringify(CONFIG_BAUDRATE) "\0"\
 	"fpga=0\0"\
 	"fpgadata=" __stringify(MV_FPGA_DATA) "\0"\
 	"fpgadatasize=" __stringify(MV_FPGA_SIZE) "\0"\
 	"mv_kernel_ram=" __stringify(MV_KERNEL_ADDR_RAM) "\0"\
 	"mv_initrd_ram=" __stringify(MV_INITRD_ADDR_RAM) "\0"\
 	"mv_dtb_ram=" __stringify(MV_DTB_ADDR_RAM) "\0"\
 	"uboota=" __stringify(CONFIG_SYS_TEXT_BASE) "\0"\
 	"fitaddr=" __stringify(MV_FITADDR) "\0"\
 	"mv_version=" U_BOOT_VERSION "\0"\
 	"mtdids=" MTDIDS_DEFAULT "\0"\
 	"mtdparts=" MTDPARTS_DEFAULT "\0"\
 	"dhcp_client_id=" MV_CI "\0"\
 	"dhcp_vendor-class-identifier=" MV_VCI "\0"\
 	"upd_uboot=dhcp;tftp bdi2000/u-boot-mergerbox-xp.bin;"\
 		"protect off all;erase $uboota +0xC0000;"\
 		"cp.b $loadaddr $uboota $filesize\0"\
 	"upd_fpga=dhcp;tftp MergerBox.rbf;erase $fpgadata +$fpgadatasize;"\
 		"cp.b $loadaddr $fpgadata $filesize\0"\
 	"upd_fit=dhcp;tftp MergerBox.fit;erase $fitaddr +0x1000000;"\
 		"cp.b $loadaddr $fitaddr $filesize\0"\
 	"addsqshrfs=set bootargs $bootargs root=/dev/ram ro "\
 		"rootfstype=squashfs\0"\
 	"addubirfs=set bootargs $bootargs ubi.mtd=9 root=ubi0:rootfs rw "\
 		"rootfstype=ubifs\0"\
 	"addusbrfs=set bootargs $bootargs root=/dev/sda1 rw "\
 		"rootfstype=ext3 usb-storage.delay_use=1 rootdelay=3\0"\
 	"netusbboot=bootp;run fpganetload fitnetload addusbrfs doboot\0"\
 	"netubiboot= bootp;run fpganetload fitnetload addubirfs doboot\0"\
 	"ubiboot=run fitprep addubirfs;set mv_initrd_ram -;run doboot\0"\
 	"doboot=bootm $mv_kernel_ram $mv_initrd_ram $mv_dtb_ram\0"\
 	"fitprep=imxtract $fitaddr kernel $mv_kernel_ram;"\
 		"imxtract $fitaddr ramdisk $mv_initrd_ram;"\
 		"imxtract $fitaddr fdt $mv_dtb_ram\0"\
 	"fdtprep=fdt addr $mv_dtb_ram;fdt boardsetup\0"\
 	"fitboot=run fitprep fdtprep addsqshrfs doboot\0"\
 	"i2c_init=run i2c_speed init_sdi_tx i2c_init_pll\0"\
 	"i2c_init_pll=i2c mw 65 9 2;i2c mw 65 9 0;i2c mw 65 5 2b;"\
 		"i2c mw 65 7 f;i2c mw 65 8 f;i2c mw 65 11 40;i2c mw 65 12 40;"\
 		"i2c mw 65 13 40; i2c mw 65 14 40; i2c mw 65 a 0\0"\
 	"i2c_speed=i2c dev 0;i2c speed 300000;i2c dev 1;i2c speed 120000\0"\
 	"init_sdi_tx=i2c mw 21 6 0;i2c mw 21 2 0;i2c mw 21 3 0;sleep 1;"\
 		"i2c mw 21 2 ff;i2c mw 21 3 3c\0"\
 	"splashimage=" __stringify(MV_SPLAH_ADDR) "\0"\
 	""

 /*
  * FPGA
  */
 #define CONFIG_FPGA_COUNT	1
 #define CONFIG_FPGA
 #define CONFIG_FPGA_ALTERA
 #define CONFIG_FPGA_CYCLON2

 #endif
	/*
	* Copyright (C) 2007 Freescale Semiconductor, Inc.
	*
	* Copyright (C) 2011 Matrix Vision GmbH
	* Andre Schwarz <andre.schwarz@matrix-vision.de>
	*
	* SPDX-License-Identifier: GPL-2.0+
	*/

	#ifndef __CONFIG_H
	#define __CONFIG_H

	#include <version.h>

	/*
	* High Level Configuration Options
	*/
	#define CONFIG_E300 1
	#define CONFIG_MPC83xx 1
	#define CONFIG_MPC837x 1
	#define CONFIG_MPC8377 1

	#define CONFIG_SYS_TEXT_BASE 0xFC000000

	#define CONFIG_PCI 1
	#define CONFIG_PCI_INDIRECT_BRIDGE 1

	#define CONFIG_MASK_AER_AO
	#define CONFIG_DISPLAY_AER_FULL

	#define CONFIG_MISC_INIT_R

	/*
	* On-board devices
	*/
	#define CONFIG_TSEC_ENET

	/*
	* System Clock Setup
	*/
	#define CONFIG_83XX_CLKIN 66666667 /* in Hz */
	#define CONFIG_PCIE
	#define CONFIG_83XX_GENERIC_PCIE_REGISTER_HOSES
	#define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN

	/*
	* Hardware Reset Configuration Word stored in EEPROM.
	*/
	#define CONFIG_SYS_HRCW_LOW 0
	#define CONFIG_SYS_HRCW_HIGH 0

	/* Arbiter Configuration Register */
	#define CONFIG_SYS_ACR_PIPE_DEP 3
	#define CONFIG_SYS_ACR_RPTCNT 3

	/* System Priority Control Regsiter */
	#define CONFIG_SYS_SPCR_TSECEP 3

	/* System Clock Configuration Register */
	#define CONFIG_SYS_SCCR_TSEC1CM 3
	#define CONFIG_SYS_SCCR_TSEC2CM 0
	#define CONFIG_SYS_SCCR_SDHCCM 3
	#define CONFIG_SYS_SCCR_ENCCM 3 /* also clock for I2C-1 */
	#define CONFIG_SYS_SCCR_USBDRCM CONFIG_SYS_SCCR_ENCCM /* must match */
	#define CONFIG_SYS_SCCR_PCIEXP1CM 3
	#define CONFIG_SYS_SCCR_PCIEXP2CM 3
	#define CONFIG_SYS_SCCR_PCICM 1
	#define CONFIG_SYS_SCCR_SATACM 0xFF

	/*
	* System IO Config
	*/
	#define CONFIG_SYS_SICRH 0x087c0000
	#define CONFIG_SYS_SICRL 0x40000000

	/*
	* Output Buffer Impedance
	*/
	#define CONFIG_SYS_OBIR 0x30000000

	/*
	* IMMR new address
	*/
	#define CONFIG_SYS_IMMR 0xE0000000

	/*
	* DDR Setup
	*/
	#define CONFIG_SYS_DDR_BASE 0x00000000
	#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE
	#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE
	#define CONFIG_SYS_83XX_DDR_USES_CS0

	#define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN \| DDRCDR_PZ_HIZ \|\
	DDRCDR_NZ_HIZ \| DDRCDR_ODT \|\
	DDRCDR_Q_DRN)

	#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05

	#define CONFIG_SYS_DDR_MODE_WEAK
	#define CONFIG_SYS_DDR_WRITE_DATA_DELAY 2
	#define CONFIG_SYS_DDR_CPO 0x1f

	/* SPD table located at offset 0x20 in extended adressing ROM
	* used for HRCW fetch after power-on reset
	*/
	#define CONFIG_SPD_EEPROM
	#define SPD_EEPROM_ADDRESS 0x50
	#define SPD_EEPROM_OFFSET 0x20
	#define SPD_EEPROM_ADDR_LEN 2

	/*
	* The reserved memory
	*/
	#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
	#define CONFIG_SYS_MONITOR_LEN (512*1024)
	#define CONFIG_SYS_MALLOC_LEN (512*1024)

	/*
	* Initial RAM Base Address Setup
	*/
	#define CONFIG_SYS_INIT_RAM_LOCK 1
	#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */
	#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* End of used area in RAM */
	#define CONFIG_SYS_GBL_DATA_SIZE 0x100 /* num bytes initial data */
	#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE -\
	CONFIG_SYS_GBL_DATA_SIZE)

	/*
	* Local Bus Configuration & Clock Setup
	*/
	#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
	#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_8
	#define CONFIG_SYS_LBC_LBCR 0x00000000
	#define CONFIG_FSL_ELBC 1

	/*
	* FLASH on the Local Bus
	*/
	#define CONFIG_SYS_FLASH_CFI
	#define CONFIG_FLASH_CFI_DRIVER
	#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT

	#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_TEXT_BASE
	#define CONFIG_SYS_FLASH_SIZE 64

	#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE
	#define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN \| LBLAWAR_64MB)

	#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE \| BR_PS_16 \|\
	BR_MS_GPCM \| BR_V)
	#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_FLASH_BASE \| OR_UPM_XAM \|\
	OR_GPCM_CSNT \| OR_GPCM_ACS_DIV2 \|\
	OR_GPCM_XACS \| OR_GPCM_SCY_15 \|\
	OR_GPCM_TRLX_SET \| OR_GPCM_EHTR_SET \|\
	OR_GPCM_EAD)

	#define CONFIG_SYS_MAX_FLASH_BANKS 1
	#define CONFIG_SYS_MAX_FLASH_SECT 512

	#undef CONFIG_SYS_FLASH_CHECKSUM
	#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Flash Erase Timeout (ms) */
	#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */

	/*
	* NAND Flash on the Local Bus
	*/
	#define CONFIG_MTD_NAND_VERIFY_WRITE 1
	#define CONFIG_SYS_MAX_NAND_DEVICE 1
	#define CONFIG_NAND_FSL_ELBC 1

	#define CONFIG_SYS_NAND_BASE 0xE0600000
	#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_NAND_BASE \| BR_DECC_CHK_GEN \|\
	BR_PS_8 \| BR_MS_FCM \| BR_V)
	#define CONFIG_SYS_OR1_PRELIM (OR_AM_32KB \| OR_FCM_BCTLD \| OR_FCM_CST \|\
	OR_FCM_CHT \| OR_FCM_SCY_1 \| OR_FCM_RST \|\
	OR_FCM_TRLX \| OR_FCM_EHTR)

	#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_NAND_BASE
	#define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN \| LBLAWAR_32KB)

	/*
	* Serial Port
	*/
	#define CONFIG_CONS_INDEX 1
	#define CONFIG_SYS_NS16550
	#define CONFIG_SYS_NS16550_SERIAL
	#define CONFIG_SYS_NS16550_REG_SIZE 1
	#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)

	#define CONFIG_SYS_BAUDRATE_TABLE \
	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}

	#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
	#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)

	#define CONFIG_CONSOLE ttyS0
	#define CONFIG_BAUDRATE 115200

	/* SERDES */
	#define CONFIG_FSL_SERDES
	#define CONFIG_FSL_SERDES1 0xe3000
	#define CONFIG_FSL_SERDES2 0xe3100

	/* Use the HUSH parser */
	#define CONFIG_SYS_HUSH_PARSER

	/* Pass open firmware flat tree */
	#define CONFIG_OF_LIBFDT 1
	#define CONFIG_OF_BOARD_SETUP 1
	#define CONFIG_OF_STDOUT_VIA_ALIAS 1

	/* I2C */
	#define CONFIG_SYS_I2C
	#define CONFIG_SYS_I2C_FSL
	#define CONFIG_SYS_FSL_I2C_SPEED 400000
	#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
	#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
	#define CONFIG_SYS_FSL_I2C2_SPEED 400000
	#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
	#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100

	/*
	* General PCI
	* Addresses are mapped 1-1.
	*/
	#define CONFIG_SYS_PCI_MEM_BASE 0x80000000
	#define CONFIG_SYS_PCI_MEM_PHYS CONFIG_SYS_PCI_MEM_BASE
	#define CONFIG_SYS_PCI_MEM_SIZE (256 << 20)
	#define CONFIG_SYS_PCI_MMIO_BASE 0x90000000
	#define CONFIG_SYS_PCI_MMIO_PHYS CONFIG_SYS_PCI_MMIO_BASE
	#define CONFIG_SYS_PCI_MMIO_SIZE (256 << 20)
	#define CONFIG_SYS_PCI_IO_BASE 0x00000000
	#define CONFIG_SYS_PCI_IO_PHYS 0xE0300000
	#define CONFIG_SYS_PCI_IO_SIZE (1 << 20)

	#ifdef CONFIG_PCIE
	#define CONFIG_SYS_PCIE1_BASE 0xA0000000
	#define CONFIG_SYS_PCIE1_CFG_BASE 0xA0000000
	#define CONFIG_SYS_PCIE1_CFG_SIZE (128 << 20)
	#define CONFIG_SYS_PCIE1_MEM_BASE 0xA8000000
	#define CONFIG_SYS_PCIE1_MEM_PHYS 0xA8000000
	#define CONFIG_SYS_PCIE1_MEM_SIZE (256 << 20)
	#define CONFIG_SYS_PCIE1_IO_BASE 0x00000000
	#define CONFIG_SYS_PCIE1_IO_PHYS 0xB8000000
	#define CONFIG_SYS_PCIE1_IO_SIZE (8 << 20)

	#define CONFIG_SYS_PCIE2_BASE 0xC0000000
	#define CONFIG_SYS_PCIE2_CFG_BASE 0xC0000000
	#define CONFIG_SYS_PCIE2_CFG_SIZE (128 << 20)
	#define CONFIG_SYS_PCIE2_MEM_BASE 0xC8000000
	#define CONFIG_SYS_PCIE2_MEM_PHYS 0xC8000000
	#define CONFIG_SYS_PCIE2_MEM_SIZE (256 << 20)
	#define CONFIG_SYS_PCIE2_IO_BASE 0x00000000
	#define CONFIG_SYS_PCIE2_IO_PHYS 0xD8000000
	#define CONFIG_SYS_PCIE2_IO_SIZE (8 << 20)
	#endif

	#define CONFIG_PCI_PNP
	#define CONFIG_PCI_SCAN_SHOW
	#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */

	/*
	* TSEC
	*/
	#define CONFIG_GMII /* MII PHY management */
	#define CONFIG_SYS_VSC8601_SKEWFIX
	#define CONFIG_SYS_VSC8601_SKEW_TX 3
	#define CONFIG_SYS_VSC8601_SKEW_RX 3

	#define CONFIG_TSEC1
	#define CONFIG_HAS_ETH0
	#define CONFIG_TSEC1_NAME "TSEC0"
	#define CONFIG_SYS_TSEC1_OFFSET 0x24000
	#define TSEC1_PHY_ADDR 0x10
	#define TSEC1_FLAGS (TSEC_GIGABIT \| TSEC_REDUCED)
	#define TSEC1_PHYIDX 0

	#define CONFIG_ETHPRIME "TSEC0"
	#define CONFIG_HAS_ETH0

	/*
	* SATA
	*/
	#define CONFIG_LIBATA
	#define CONFIG_FSL_SATA

	#define CONFIG_SYS_SATA_MAX_DEVICE 2
	#define CONFIG_SATA1
	#define CONFIG_SYS_SATA1_OFFSET 0x18000
	#define CONFIG_SYS_SATA1 (CONFIG_SYS_IMMR + CONFIG_SYS_SATA1_OFFSET)
	#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA
	#define CONFIG_SATA2
	#define CONFIG_SYS_SATA2_OFFSET 0x19000
	#define CONFIG_SYS_SATA2 (CONFIG_SYS_IMMR + CONFIG_SYS_SATA2_OFFSET)
	#define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA

	#define CONFIG_LBA48
	#define CONFIG_CMD_SATA
	#define CONFIG_DOS_PARTITION
	#define CONFIG_CMD_EXT2

	/*
	* BOOTP options
	*/
	#define CONFIG_BOOTP_BOOTFILESIZE
	#define CONFIG_BOOTP_BOOTPATH
	#define CONFIG_BOOTP_GATEWAY
	#define CONFIG_BOOTP_HOSTNAME
	#define CONFIG_BOOTP_VENDOREX
	#define CONFIG_BOOTP_SUBNETMASK
	#define CONFIG_BOOTP_DNS
	#define CONFIG_BOOTP_DNS2
	#define CONFIG_BOOTP_NTPSERVER
	#define CONFIG_BOOTP_RANDOM_DELAY
	#define CONFIG_BOOTP_SEND_HOSTNAME

	/*
	* Command line configuration.
	*/
	#include <config_cmd_default.h>

	#define CONFIG_CMD_ASKENV
	#define CONFIG_CMD_NAND
	#define CONFIG_CMD_PING
	#define CONFIG_CMD_EEPROM
	#define CONFIG_CMD_I2C
	#define CONFIG_CMD_MII
	#define CONFIG_CMD_PCI
	#define CONFIG_CMD_USB
	#define CONFIG_CMD_SPI
	#define CONFIG_CMD_DHCP
	#define CONFIG_CMD_UBI
	#define CONFIG_CMD_UBIFS
	#define CONFIG_CMD_MTDPARTS
	#define CONFIG_CMD_SATA

	#define CONFIG_CMD_EXT2
	#define CONFIG_CMD_FAT
	#define CONFIG_CMD_JFFS2

	#define CONFIG_RBTREE
	#define CONFIG_LZO

	#define CONFIG_MTD_DEVICE
	#define CONFIG_MTD_PARTITIONS

	#define CONFIG_FLASH_CFI_MTD
	#define MTDIDS_DEFAULT "nor0=NOR,nand0=NAND"
	#define MTDPARTS_DEFAULT "mtdparts=NOR:1M(u-boot),2M(FPGA);NAND:-(root)"

	#define CONFIG_FIT
	#define CONFIG_FIT_VERBOSE 1

	#define CONFIG_CMDLINE_EDITING 1
	#define CONFIG_AUTO_COMPLETE

	/*
	* Miscellaneous configurable options
	*/
	#define CONFIG_SYS_LONGHELP
	#define CONFIG_SYS_LOAD_ADDR 0x2000000
	#define CONFIG_LOADADDR 0x4000000
	#define CONFIG_SYS_CBSIZE 256

	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
	#define CONFIG_SYS_MAXARGS 16
	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE

	#define CONFIG_LOADS_ECHO 1
	#define CONFIG_SYS_LOADS_BAUD_CHANGE 1

	#define CONFIG_SYS_MEMTEST_START (60<<20)
	#define CONFIG_SYS_MEMTEST_END (70<<20)

	/*
	* For booting Linux, the board info and command line data
	* have to be in the first 256 MB of memory, since this is
	* the maximum mapped by the Linux kernel during initialization.
	*/
	#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux */

	/*
	* Core HID Setup
	*/
	#define CONFIG_SYS_HID0_INIT 0x000000000
	#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK \| \
	HID0_ENABLE_INSTRUCTION_CACHE)
	#define CONFIG_SYS_HID2 HID2_HBE

	/*
	* MMU Setup
	*/
	#define CONFIG_HIGH_BATS 1

	/* DDR: cache cacheable */
	#define CONFIG_SYS_SDRAM CONFIG_SYS_SDRAM_BASE

	#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM \| BATL_PP_RW \|\
	BATL_MEMCOHERENCE)
	#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM \| BATU_BL_256M \| BATU_VS \|\
	BATU_VP)
	#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
	#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U

	/* unused */
	#define CONFIG_SYS_IBAT1L (0)
	#define CONFIG_SYS_IBAT1U (0)
	#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
	#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U

	/* IMMRBAR, PCI IO and NAND: cache-inhibit and guarded */
	#define CONFIG_SYS_IBAT2L (CONFIG_SYS_IMMR \| BATL_PP_RW \|\
	BATL_CACHEINHIBIT \| BATL_GUARDEDSTORAGE)
	#define CONFIG_SYS_IBAT2U (CONFIG_SYS_IMMR \| BATU_BL_8M \| BATU_VS \|\
	BATU_VP)
	#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L
	#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U

	/* unused */
	#define CONFIG_SYS_IBAT3L (0)
	#define CONFIG_SYS_IBAT3U (0)
	#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L
	#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U

	/* FLASH: icache cacheable, but dcache-inhibit and guarded */
	#define CONFIG_SYS_IBAT4L (CONFIG_SYS_FLASH_BASE \| BATL_PP_RW \|\
	BATL_MEMCOHERENCE)
	#define CONFIG_SYS_IBAT4U (CONFIG_SYS_FLASH_BASE \| BATU_BL_64M \|\
	BATU_VS \| BATU_VP)
	#define CONFIG_SYS_DBAT4L (CONFIG_SYS_FLASH_BASE \| BATL_PP_RW \| \
	BATL_CACHEINHIBIT \| BATL_GUARDEDSTORAGE)
	#define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U

	/* Stack in dcache: cacheable, no memory coherence */
	#define CONFIG_SYS_IBAT5L (CONFIG_SYS_INIT_RAM_ADDR \| BATL_PP_RW)
	#define CONFIG_SYS_IBAT5U (CONFIG_SYS_INIT_RAM_ADDR \| BATU_BL_128K \|\
	BATU_VS \| BATU_VP)
	#define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L
	#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U

	/* PCI MEM space: cacheable */
	#define CONFIG_SYS_IBAT6L (CONFIG_SYS_PCI_MEM_PHYS \| BATL_PP_RW \|\
	BATL_MEMCOHERENCE)
	#define CONFIG_SYS_IBAT6U (CONFIG_SYS_PCI_MEM_PHYS \| BATU_BL_256M \|\
	BATU_VS \| BATU_VP)
	#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L
	#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U

	/* PCI MMIO space: cache-inhibit and guarded */
	#define CONFIG_SYS_IBAT7L (CONFIG_SYS_PCI_MMIO_PHYS \| BATL_PP_RW \| \
	BATL_CACHEINHIBIT \| BATL_GUARDEDSTORAGE)
	#define CONFIG_SYS_IBAT7U (CONFIG_SYS_PCI_MMIO_PHYS \| BATU_BL_256M \|\
	BATU_VS \| BATU_VP)
	#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L
	#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U

	/*
	* I2C EEPROM settings
	*/
	#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
	#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6
	#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
	#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
	#define CONFIG_SYS_EEPROM_SIZE 0x4000

	/*
	* Environment Configuration
	*/
	#define CONFIG_SYS_FLASH_PROTECTION
	#define CONFIG_ENV_OVERWRITE
	#define CONFIG_ENV_IS_IN_FLASH 1
	#define CONFIG_ENV_ADDR 0xFFD00000
	#define CONFIG_ENV_SECT_SIZE 0x20000
	#define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE

	/*
	* Video
	*/
	#define CONFIG_VIDEO
	#define CONFIG_VIDEO_SM501_PCI
	#define VIDEO_FB_LITTLE_ENDIAN
	#define CONFIG_CMD_BMP
	#define CONFIG_VIDEO_SM501
	#define CONFIG_VIDEO_SM501_32BPP
	#define CONFIG_VIDEO_SM501_FBMEM_OFFSET 0x10000
	#define CONFIG_CFB_CONSOLE
	#define CONFIG_VIDEO_LOGO
	#define CONFIG_VIDEO_BMP_LOGO
	#define CONFIG_VGA_AS_SINGLE_DEVICE
	#define CONFIG_SPLASH_SCREEN
	#define CONFIG_SYS_CONSOLE_IS_IN_ENV
	#define CONFIG_VIDEO_BMP_GZIP
	#define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE (2 << 20)

	/*
	* SPI
	*/
	#define CONFIG_MPC8XXX_SPI

	/*
	* USB
	*/
	#define CONFIG_SYS_USB_HOST
	#define CONFIG_USB_EHCI
	#define CONFIG_USB_EHCI_FSL
	#define CONFIG_HAS_FSL_DR_USB
	#define CONFIG_EHCI_HCD_INIT_AFTER_RESET

	#define CONFIG_USB_STORAGE
	#define CONFIG_USB_KEYBOARD
	/*
	*
	*/
	#define CONFIG_BOOTDELAY 5
	#define CONFIG_AUTOBOOT_KEYED
	#define CONFIG_AUTOBOOT_STOP_STR "s"
	#define CONFIG_ZERO_BOOTDELAY_CHECK
	#define CONFIG_RESET_TO_RETRY 1000

	#define MV_CI "MergerBox"
	#define MV_VCI "MergerBox"
	#define MV_FPGA_DATA 0xfc100000
	#define MV_FPGA_SIZE 0x00200000

	#define CONFIG_SHOW_BOOT_PROGRESS 1

	#define MV_KERNEL_ADDR_RAM 0x02800000
	#define MV_DTB_ADDR_RAM 0x00600000
	#define MV_INITRD_ADDR_RAM 0x01000000
	#define MV_FITADDR 0xfc300000
	#define MV_SPLAH_ADDR 0xffe00000

	#define CONFIG_BOOTCOMMAND "run i2c_init;if test ${boot_sqfs} -eq 1;"\
	"then; run fitboot;else;run ubiboot;fi;"
	#define CONFIG_BOOTARGS "console=ttyS0,115200n8"

	#define CONFIG_EXTRA_ENV_SETTINGS \
	"console_nr=0\0"\
	"stdin=serial\0"\
	"stdout=serial\0"\
	"stderr=serial\0"\
	"boot_sqfs=1\0"\
	"usb_dr_mode=host\0"\
	"bootfile=MergerBox.fit\0"\
	"baudrate=" __stringify(CONFIG_BAUDRATE) "\0"\
	"fpga=0\0"\
	"fpgadata=" __stringify(MV_FPGA_DATA) "\0"\
	"fpgadatasize=" __stringify(MV_FPGA_SIZE) "\0"\
	"mv_kernel_ram=" __stringify(MV_KERNEL_ADDR_RAM) "\0"\
	"mv_initrd_ram=" __stringify(MV_INITRD_ADDR_RAM) "\0"\
	"mv_dtb_ram=" __stringify(MV_DTB_ADDR_RAM) "\0"\
	"uboota=" __stringify(CONFIG_SYS_TEXT_BASE) "\0"\
	"fitaddr=" __stringify(MV_FITADDR) "\0"\
	"mv_version=" U_BOOT_VERSION "\0"\
	"mtdids=" MTDIDS_DEFAULT "\0"\
	"mtdparts=" MTDPARTS_DEFAULT "\0"\
	"dhcp_client_id=" MV_CI "\0"\
	"dhcp_vendor-class-identifier=" MV_VCI "\0"\
	"upd_uboot=dhcp;tftp bdi2000/u-boot-mergerbox-xp.bin;"\
	"protect off all;erase $uboota +0xC0000;"\
	"cp.b $loadaddr $uboota $filesize\0"\
	"upd_fpga=dhcp;tftp MergerBox.rbf;erase $fpgadata +$fpgadatasize;"\
	"cp.b $loadaddr $fpgadata $filesize\0"\
	"upd_fit=dhcp;tftp MergerBox.fit;erase $fitaddr +0x1000000;"\
	"cp.b $loadaddr $fitaddr $filesize\0"\
	"addsqshrfs=set bootargs $bootargs root=/dev/ram ro "\
	"rootfstype=squashfs\0"\
	"addubirfs=set bootargs $bootargs ubi.mtd=9 root=ubi0:rootfs rw "\
	"rootfstype=ubifs\0"\
	"addusbrfs=set bootargs $bootargs root=/dev/sda1 rw "\
	"rootfstype=ext3 usb-storage.delay_use=1 rootdelay=3\0"\
	"netusbboot=bootp;run fpganetload fitnetload addusbrfs doboot\0"\
	"netubiboot= bootp;run fpganetload fitnetload addubirfs doboot\0"\
	"ubiboot=run fitprep addubirfs;set mv_initrd_ram -;run doboot\0"\
	"doboot=bootm $mv_kernel_ram $mv_initrd_ram $mv_dtb_ram\0"\
	"fitprep=imxtract $fitaddr kernel $mv_kernel_ram;"\
	"imxtract $fitaddr ramdisk $mv_initrd_ram;"\
	"imxtract $fitaddr fdt $mv_dtb_ram\0"\
	"fdtprep=fdt addr $mv_dtb_ram;fdt boardsetup\0"\
	"fitboot=run fitprep fdtprep addsqshrfs doboot\0"\
	"i2c_init=run i2c_speed init_sdi_tx i2c_init_pll\0"\
	"i2c_init_pll=i2c mw 65 9 2;i2c mw 65 9 0;i2c mw 65 5 2b;"\
	"i2c mw 65 7 f;i2c mw 65 8 f;i2c mw 65 11 40;i2c mw 65 12 40;"\
	"i2c mw 65 13 40; i2c mw 65 14 40; i2c mw 65 a 0\0"\
	"i2c_speed=i2c dev 0;i2c speed 300000;i2c dev 1;i2c speed 120000\0"\
	"init_sdi_tx=i2c mw 21 6 0;i2c mw 21 2 0;i2c mw 21 3 0;sleep 1;"\
	"i2c mw 21 2 ff;i2c mw 21 3 3c\0"\
	"splashimage=" __stringify(MV_SPLAH_ADDR) "\0"\
	""

	/*
	* FPGA
	*/
	#define CONFIG_FPGA_COUNT 1
	#define CONFIG_FPGA
	#define CONFIG_FPGA_ALTERA
	#define CONFIG_FPGA_CYCLON2

	#endif