| /* |
| * (C) Copyright 2001-2003 |
| * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| /* |
| * board/config.h - configuration options, board specific |
| */ |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| /* |
| * High Level Configuration Options |
| * (easy to change) |
| */ |
| |
| #define CONFIG_405GP 1 /* This is a PPC405 CPU */ |
| #define CONFIG_4xx 1 /* ...member of PPC4xx family */ |
| #define CONFIG_CPCI405 1 /* ...on a CPCI405 board */ |
| #define CONFIG_CPCI405_VER2 1 /* ...version 2 */ |
| #define CONFIG_CPCI405AB 1 /* ...and special AB version */ |
| |
| #define CONFIG_SYS_TEXT_BASE 0xFFFC0000 |
| |
| #define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */ |
| #define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */ |
| |
| #define CONFIG_SYS_CLK_FREQ 33330000 /* external frequency to pll */ |
| |
| #define CONFIG_BAUDRATE 9600 |
| #define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */ |
| |
| #undef CONFIG_BOOTARGS |
| #undef CONFIG_BOOTCOMMAND |
| |
| #define CONFIG_PREBOOT /* enable preboot variable */ |
| |
| #undef CONFIG_LOADS_ECHO /* echo on for serial download */ |
| #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ |
| |
| #define CONFIG_PPC4xx_EMAC |
| #define CONFIG_MII 1 /* MII PHY management */ |
| #define CONFIG_PHY_ADDR 0 /* PHY address */ |
| #define CONFIG_LXT971_NO_SLEEP 1 /* disable sleep mode in LXT971 */ |
| #define CONFIG_RESET_PHY_R 1 /* use reset_phy() to disable phy sleep mode */ |
| |
| #undef CONFIG_HAS_ETH1 |
| |
| #define CONFIG_RTC_M48T35A 1 /* ST Electronics M48 timekeeper */ |
| |
| /* |
| * BOOTP options |
| */ |
| #define CONFIG_BOOTP_SUBNETMASK |
| #define CONFIG_BOOTP_GATEWAY |
| #define CONFIG_BOOTP_HOSTNAME |
| #define CONFIG_BOOTP_BOOTPATH |
| #define CONFIG_BOOTP_DNS |
| #define CONFIG_BOOTP_DNS2 |
| #define CONFIG_BOOTP_SEND_HOSTNAME |
| |
| |
| /* |
| * Command line configuration. |
| */ |
| #include <config_cmd_default.h> |
| |
| #define CONFIG_CMD_DHCP |
| #define CONFIG_CMD_PCI |
| #define CONFIG_CMD_IRQ |
| #define CONFIG_CMD_IDE |
| #define CONFIG_CMD_FAT |
| #define CONFIG_CMD_ELF |
| #define CONFIG_CMD_DATE |
| #define CONFIG_CMD_I2C |
| #define CONFIG_CMD_MII |
| #define CONFIG_CMD_PING |
| #define CONFIG_CMD_BSP |
| #define CONFIG_CMD_EEPROM |
| |
| |
| #define CONFIG_MAC_PARTITION |
| #define CONFIG_DOS_PARTITION |
| |
| #define CONFIG_SUPPORT_VFAT |
| |
| #undef CONFIG_WATCHDOG /* watchdog disabled */ |
| |
| #define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */ |
| |
| /* |
| * Miscellaneous configurable options |
| */ |
| #define CONFIG_SYS_LONGHELP /* undef to save memory */ |
| |
| #undef CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */ |
| |
| #if defined(CONFIG_CMD_KGDB) |
| #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ |
| #else |
| #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ |
| #endif |
| #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ |
| #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ |
| #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ |
| |
| #define CONFIG_SYS_DEVICE_NULLDEV 1 /* include nulldev device */ |
| |
| #define CONFIG_SYS_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/ |
| |
| #define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ |
| #define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ |
| |
| #define CONFIG_CONS_INDEX 1 /* Use UART0 */ |
| #define CONFIG_SYS_NS16550 |
| #define CONFIG_SYS_NS16550_SERIAL |
| #define CONFIG_SYS_NS16550_REG_SIZE 1 |
| #define CONFIG_SYS_NS16550_CLK get_serial_clock() |
| |
| #undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external serial clock used */ |
| #define CONFIG_SYS_BASE_BAUD 691200 |
| |
| /* The following table includes the supported baudrates */ |
| #define CONFIG_SYS_BAUDRATE_TABLE \ |
| { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \ |
| 57600, 115200, 230400, 460800, 921600 } |
| |
| #define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ |
| #define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */ |
| |
| #define CONFIG_CMDLINE_EDITING /* add command line history */ |
| |
| #define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ |
| |
| #define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ |
| |
| #define CONFIG_AUTOBOOT_KEYED 1 |
| #define CONFIG_AUTOBOOT_PROMPT \ |
| "Press SPACE to abort autoboot in %d seconds\n", bootdelay |
| #undef CONFIG_AUTOBOOT_DELAY_STR |
| #define CONFIG_AUTOBOOT_STOP_STR " " |
| |
| #define CONFIG_SYS_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */ |
| |
| /*----------------------------------------------------------------------- |
| * PCI stuff |
| *----------------------------------------------------------------------- |
| */ |
| #define PCI_HOST_ADAPTER 0 /* configure as pci adapter */ |
| #define PCI_HOST_FORCE 1 /* configure as pci host */ |
| #define PCI_HOST_AUTO 2 /* detected via arbiter enable */ |
| |
| #define CONFIG_PCI /* include pci support */ |
| #define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */ |
| #define CONFIG_PCI_HOST PCI_HOST_AUTO /* select pci host function */ |
| #define CONFIG_PCI_PNP /* do pci plug-and-play */ |
| /* resource configuration */ |
| |
| #define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */ |
| |
| #define CONFIG_PCI_CONFIG_HOST_BRIDGE 1 /* don't skip host bridge config*/ |
| |
| #define CONFIG_PCI_BOOTDELAY 0 /* enable pci bootdelay variable*/ |
| |
| #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */ |
| #define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */ |
| #define CONFIG_SYS_PCI_SUBSYS_DEVICEID2 0x0406 /* PCI Device ID: CPCI-405-A */ |
| #define CONFIG_SYS_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/ |
| #define CONFIG_SYS_PCI_PTM1LA (bd->bi_memstart) /* point to sdram */ |
| #define CONFIG_SYS_PCI_PTM1MS (~(bd->bi_memsize - 1) | 1) /* memsize, enable hard-wired to 1 */ |
| #define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ |
| #define CONFIG_SYS_PCI_PTM2LA 0xffc00000 /* point to flash */ |
| #define CONFIG_SYS_PCI_PTM2MS 0xffc00001 /* 4MB, enable */ |
| #define CONFIG_SYS_PCI_PTM2PCI (bd->bi_memsize) /* host use this pci address */ |
| |
| #define CONFIG_PCI_4xx_PTM_OVERWRITE 1 /* overwrite PTMx settings by env */ |
| |
| /*----------------------------------------------------------------------- |
| * IDE/ATA stuff |
| *----------------------------------------------------------------------- |
| */ |
| #undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */ |
| #undef CONFIG_IDE_LED /* no led for ide supported */ |
| #define CONFIG_IDE_RESET 1 /* reset for ide supported */ |
| |
| #define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE busses */ |
| #define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */ |
| |
| #define CONFIG_SYS_ATA_BASE_ADDR 0xF0100000 |
| #define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 |
| |
| #define CONFIG_SYS_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */ |
| #define CONFIG_SYS_ATA_REG_OFFSET 0x0000 /* Offset for normal register accesses */ |
| #define CONFIG_SYS_ATA_ALT_OFFSET 0x0000 /* Offset for alternate registers */ |
| |
| /*----------------------------------------------------------------------- |
| * Start addresses for the final memory configuration |
| * (Set up by the startup code) |
| * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 |
| */ |
| #define CONFIG_SYS_SDRAM_BASE 0x00000000 |
| #define CONFIG_SYS_FLASH_BASE 0xFFFC0000 |
| #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE |
| #define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */ |
| #define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */ |
| |
| #define CONFIG_PRAM 0 /* use pram variable to overwrite */ |
| |
| /* |
| * For booting Linux, the board info and command line data |
| * have to be in the first 8 MB of memory, since this is |
| * the maximum mapped by the Linux kernel during initialization. |
| */ |
| #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ |
| |
| #define CONFIG_OF_LIBFDT |
| #define CONFIG_OF_BOARD_SETUP |
| |
| /*----------------------------------------------------------------------- |
| * FLASH organization |
| */ |
| #define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */ |
| #define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */ |
| |
| #define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ |
| #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ |
| |
| #define CONFIG_SYS_FLASH_WORD_SIZE unsigned short /* flash word size (width) */ |
| #define CONFIG_SYS_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */ |
| #define CONFIG_SYS_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */ |
| /* |
| * The following defines are added for buggy IOP480 byte interface. |
| * All other boards should use the standard values (CPCI405 etc.) |
| */ |
| #define CONFIG_SYS_FLASH_READ0 0x0000 /* 0 is standard */ |
| #define CONFIG_SYS_FLASH_READ1 0x0001 /* 1 is standard */ |
| #define CONFIG_SYS_FLASH_READ2 0x0002 /* 2 is standard */ |
| |
| #define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ |
| |
| /*----------------------------------------------------------------------- |
| * I2C EEPROM (CAT24WC32) for environment |
| */ |
| #define CONFIG_SYS_I2C |
| #define CONFIG_SYS_I2C_PPC4XX |
| #define CONFIG_SYS_I2C_PPC4XX_CH0 |
| #define CONFIG_SYS_I2C_PPC4XX_SPEED_0 100000 |
| #define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F |
| |
| #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC32 */ |
| #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* Bytes of address */ |
| /* mask of address bits that overflow into the "EEPROM chip address" */ |
| #define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x01 |
| #define CONFIG_SYS_I2C_MULTI_EEPROMS 1 /* more than one eeprom used! */ |
| #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 /* The Catalyst CAT24WC32 has */ |
| /* 32 byte page write mode using*/ |
| /* last 5 bits of the address */ |
| #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ |
| |
| /* Use EEPROM for environment variables */ |
| |
| #define CONFIG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */ |
| #define CONFIG_ENV_OFFSET 0x000 /* environment starts at the beginning of the EEPROM */ |
| #define CONFIG_ENV_SIZE 0x800 /* 2048 bytes may be used for env vars*/ |
| /* total size of a CAT24WC32 is 4096 bytes */ |
| |
| #define CONFIG_SYS_NVRAM_BASE_ADDR 0xf0200000 /* NVRAM base address */ |
| #define CONFIG_SYS_NVRAM_SIZE (32*1024) /* NVRAM size */ |
| #define CONFIG_SYS_VXWORKS_MAC_PTR (CONFIG_SYS_NVRAM_BASE_ADDR+0x6900) /* VxWorks eth-addr*/ |
| |
| /* |
| * Init Memory Controller: |
| * |
| * BR0/1 and OR0/1 (FLASH) |
| */ |
| |
| #define FLASH_BASE0_PRELIM 0xFF800000 /* FLASH bank #0 */ |
| #define FLASH_BASE1_PRELIM 0xFFC00000 /* FLASH bank #1 */ |
| |
| /*----------------------------------------------------------------------- |
| * External Bus Controller (EBC) Setup |
| */ |
| |
| /* Memory Bank 0 (Flash Bank 0) initialization */ |
| #define CONFIG_SYS_EBC_PB0AP 0x92015480 |
| #define CONFIG_SYS_EBC_PB0CR 0xFFC5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */ |
| |
| /* Memory Bank 1 (Flash Bank 1) initialization */ |
| #define CONFIG_SYS_EBC_PB1AP 0x92015480 |
| #define CONFIG_SYS_EBC_PB1CR 0xFF85A000 /* BAS=0xFF8,BS=4MB,BU=R/W,BW=16bit */ |
| |
| /* Memory Bank 2 (CAN0, 1) initialization */ |
| #define CONFIG_SYS_EBC_PB2AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */ |
| #define CONFIG_SYS_EBC_PB2CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */ |
| #define CONFIG_SYS_LED_ADDR 0xF0000380 |
| |
| /* Memory Bank 3 (CompactFlash IDE) initialization */ |
| #define CONFIG_SYS_EBC_PB3AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */ |
| #define CONFIG_SYS_EBC_PB3CR 0xF011A000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */ |
| |
| /* Memory Bank 4 (NVRAM/RTC) initialization */ |
| /*#define CONFIG_SYS_EBC_PB4AP 0x01805280 / * TWT=3,WBN=1,WBF=1,TH=1,SOR=1 */ |
| #define CONFIG_SYS_EBC_PB4AP 0x01805680 /* TWT=3,WBN=1,WBF=1,TH=3,SOR=1 */ |
| #define CONFIG_SYS_EBC_PB4CR 0xF0218000 /* BAS=0xF02,BS=1MB,BU=R/W,BW=8bit */ |
| |
| /* Memory Bank 5 (optional Quart) initialization */ |
| #define CONFIG_SYS_EBC_PB5AP 0x04005B80 /* TWT=8,WBN=1,WBF=1,TH=5,RE=1,SOR=1*/ |
| #define CONFIG_SYS_EBC_PB5CR 0xF0318000 /* BAS=0xF03,BS=1MB,BU=R/W,BW=8bit */ |
| |
| /* Memory Bank 6 (FPGA internal) initialization */ |
| #define CONFIG_SYS_EBC_PB6AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */ |
| #define CONFIG_SYS_EBC_PB6CR 0xF041A000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */ |
| #define CONFIG_SYS_FPGA_BASE_ADDR 0xF0400000 |
| |
| /*----------------------------------------------------------------------- |
| * FPGA stuff |
| */ |
| /* FPGA internal regs */ |
| #define CONFIG_SYS_FPGA_MODE 0x00 |
| #define CONFIG_SYS_FPGA_STATUS 0x02 |
| #define CONFIG_SYS_FPGA_TS 0x04 |
| #define CONFIG_SYS_FPGA_TS_LOW 0x06 |
| #define CONFIG_SYS_FPGA_TS_CAP0 0x10 |
| #define CONFIG_SYS_FPGA_TS_CAP0_LOW 0x12 |
| #define CONFIG_SYS_FPGA_TS_CAP1 0x14 |
| #define CONFIG_SYS_FPGA_TS_CAP1_LOW 0x16 |
| #define CONFIG_SYS_FPGA_TS_CAP2 0x18 |
| #define CONFIG_SYS_FPGA_TS_CAP2_LOW 0x1a |
| #define CONFIG_SYS_FPGA_TS_CAP3 0x1c |
| #define CONFIG_SYS_FPGA_TS_CAP3_LOW 0x1e |
| |
| /* FPGA Mode Reg */ |
| #define CONFIG_SYS_FPGA_MODE_CF_RESET 0x0001 |
| #define CONFIG_SYS_FPGA_MODE_DUART_RESET 0x0002 |
| #define CONFIG_SYS_FPGA_MODE_ENABLE_OUTPUT 0x0004 /* only set on CPCI-405 Ver 3 */ |
| #define CONFIG_SYS_FPGA_MODE_1WIRE_DIR 0x0100 /* dir=1 -> output */ |
| #define CONFIG_SYS_FPGA_MODE_SIM_OK_DIR 0x0200 |
| #define CONFIG_SYS_FPGA_MODE_TESTRIG_FAIL_DIR 0x0400 |
| #define CONFIG_SYS_FPGA_MODE_1WIRE 0x1000 |
| #define CONFIG_SYS_FPGA_MODE_SIM_OK 0x2000 /* wired-or net from all devices */ |
| #define CONFIG_SYS_FPGA_MODE_TESTRIG_FAIL 0x4000 |
| |
| /* FPGA Status Reg */ |
| #define CONFIG_SYS_FPGA_STATUS_DIP0 0x0001 |
| #define CONFIG_SYS_FPGA_STATUS_DIP1 0x0002 |
| #define CONFIG_SYS_FPGA_STATUS_DIP2 0x0004 |
| #define CONFIG_SYS_FPGA_STATUS_FLASH 0x0008 |
| #define CONFIG_SYS_FPGA_STATUS_1WIRE 0x1000 |
| #define CONFIG_SYS_FPGA_STATUS_SIM_OK 0x2000 |
| |
| #define CONFIG_SYS_FPGA_SPARTAN2 1 /* using Xilinx Spartan 2 now */ |
| #define CONFIG_SYS_FPGA_MAX_SIZE 128*1024 /* 128kByte is enough for XC2S30 */ |
| |
| /* FPGA program pin configuration */ |
| #define CONFIG_SYS_FPGA_PRG 0x04000000 /* FPGA program pin (ppc output) */ |
| #define CONFIG_SYS_FPGA_CLK 0x02000000 /* FPGA clk pin (ppc output) */ |
| #define CONFIG_SYS_FPGA_DATA 0x01000000 /* FPGA data pin (ppc output) */ |
| #define CONFIG_SYS_FPGA_INIT 0x00010000 /* FPGA init pin (ppc input) */ |
| #define CONFIG_SYS_FPGA_DONE 0x00008000 /* FPGA done pin (ppc input) */ |
| |
| /*----------------------------------------------------------------------- |
| * Definitions for initial stack pointer and data area (in data cache) |
| */ |
| #define CONFIG_SYS_INIT_DCACHE_CS 7 /* use cs # 7 for data cache memory */ |
| |
| #define CONFIG_SYS_INIT_RAM_ADDR 0x40000000 /* use data cache */ |
| #define CONFIG_SYS_INIT_RAM_SIZE 0x2000 /* Size of used area in RAM */ |
| #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) |
| #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET |
| |
| #endif /* __CONFIG_H */ |