board/ifm/ac14xx/ac14xx.c - github/trini/u-boot - Gitiles

 /*
  * (C) Copyright 2009 Wolfgang Denk <wd@denx.de>
  * (C) Copyright 2009 Dave Srl www.dave.eu
  * (C) Copyright 2010 ifm ecomatic GmbH
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */

 #include <common.h>
 #include <asm/bitops.h>
 #include <command.h>
 #include <asm/io.h>
 #include <asm/processor.h>
 #include <asm/mpc512x.h>
 #include <fdt_support.h>
 #ifdef CONFIG_MISC_INIT_R
 #include <i2c.h>
 #endif

 static int eeprom_diag;
 static int mac_diag;
 static int gpio_diag;

 DECLARE_GLOBAL_DATA_PTR;

 static void gpio_configure(void)
 {
 	immap_t *im;
 	gpio512x_t *gpioregs;

 	im = (immap_t *) CONFIG_SYS_IMMR;
 	gpioregs = &im->gpio;
 	out_be32(&gpioregs->gpodr, 0x00290000); /* open drain */
 	out_be32(&gpioregs->gpdat, 0x80001040); /* data (when output) */

 	/*
 	 * out_be32(&gpioregs->gpdir, 0xC2293020);
 	 * workaround for a hardware effect: configure direction in pieces,
 	 * setting all outputs at once drops the reset line too low and
 	 * makes us lose the MII connection (breaks ethernet for us)
 	 */
 	out_be32(&gpioregs->gpdir, 0x02003060); /* direction */
 	setbits_be32(&gpioregs->gpdir, 0x00200000); /* += reset asi */
 	udelay(10);
 	setbits_be32(&gpioregs->gpdir, 0x00080000); /* += reset safety */
 	udelay(10);
 	setbits_be32(&gpioregs->gpdir, 0x00010000); /* += reset comm */
 	udelay(10);
 	setbits_be32(&gpioregs->gpdir, 0xC0000000); /* += backlight, KB sel */

 	/* to turn from red to yellow when U-Boot runs */
 	setbits_be32(&gpioregs->gpdat, 0x00002020);
 	out_be32(&gpioregs->gpimr, 0x00000000); /* interrupt mask */
 	out_be32(&gpioregs->gpicr1, 0x00000004); /* interrupt sense part 1 */
 	out_be32(&gpioregs->gpicr2, 0x00A80000); /* interrupt sense part 2 */
 	out_be32(&gpioregs->gpier, 0xFFFFFFFF); /* interrupt events, clear */
 }

 /* the physical location of the pins */
 #define GPIOKEY_ROW_BITMASK	0x40000000
 #define GPIOKEY_ROW_UPPER	0
 #define GPIOKEY_ROW_LOWER	1

 #define GPIOKEY_COL0_BITMASK	0x20000000
 #define GPIOKEY_COL1_BITMASK	0x10000000
 #define GPIOKEY_COL2_BITMASK	0x08000000

 /* the logical presentation of pressed keys */
 #define GPIOKEY_BIT_FNLEFT	(1 << 5)
 #define GPIOKEY_BIT_FNRIGHT	(1 << 4)
 #define GPIOKEY_BIT_DIRUP	(1 << 3)
 #define GPIOKEY_BIT_DIRLEFT	(1 << 2)
 #define GPIOKEY_BIT_DIRRIGHT	(1 << 1)
 #define GPIOKEY_BIT_DIRDOWN	(1 << 0)

 /* the hotkey combination which starts recovery */
 #define GPIOKEY_BITS_RECOVERY	(GPIOKEY_BIT_FNLEFT | GPIOKEY_BIT_DIRUP | \
 				 GPIOKEY_BIT_DIRDOWN)

 static void gpio_selectrow(gpio512x_t *gpioregs, u32 row)
 {

 	if (row)
 		setbits_be32(&gpioregs->gpdat, GPIOKEY_ROW_BITMASK);
 	else
 		clrbits_be32(&gpioregs->gpdat, GPIOKEY_ROW_BITMASK);
 	udelay(10);
 }

 static u32 gpio_querykbd(void)
 {
 	immap_t *im;
 	gpio512x_t *gpioregs;
 	u32 keybits;
 	u32 input;

 	im = (immap_t *)CONFIG_SYS_IMMR;
 	gpioregs = &im->gpio;
 	keybits = 0;

 	/* query upper row */
 	gpio_selectrow(gpioregs, GPIOKEY_ROW_UPPER);
 	input = in_be32(&gpioregs->gpdat);
 	if ((input & GPIOKEY_COL0_BITMASK) == 0)
 		keybits |= GPIOKEY_BIT_FNLEFT;
 	if ((input & GPIOKEY_COL1_BITMASK) == 0)
 		keybits |= GPIOKEY_BIT_DIRUP;
 	if ((input & GPIOKEY_COL2_BITMASK) == 0)
 		keybits |= GPIOKEY_BIT_FNRIGHT;

 	/* query lower row */
 	gpio_selectrow(gpioregs, GPIOKEY_ROW_LOWER);
 	input = in_be32(&gpioregs->gpdat);
 	if ((input & GPIOKEY_COL0_BITMASK) == 0)
 		keybits |= GPIOKEY_BIT_DIRLEFT;
 	if ((input & GPIOKEY_COL1_BITMASK) == 0)
 		keybits |= GPIOKEY_BIT_DIRRIGHT;
 	if ((input & GPIOKEY_COL2_BITMASK) == 0)
 		keybits |= GPIOKEY_BIT_DIRDOWN;

 	/* return bit pattern for keys */
 	return keybits;
 }

 /* excerpt from the recovery's hw_info.h */

 struct __attribute__ ((__packed__)) eeprom_layout {
 	char	magic[3];	/** 'ifm' */
 	u8	len[2];		/** content length without magic/len fields */
 	u8	version[3];	/** structure version */
 	u8	type;		/** type of PCB */
 	u8	reserved[0x37];	/** padding up to offset 0x40 */
 	u8	macaddress[6];	/** ethernet MAC (for the mainboard) @0x40 */
 };

 #define HW_COMP_MAINCPU 2

 static struct eeprom_layout eeprom_content;
 static int eeprom_was_read;	/* has_been_read */
 static int eeprom_is_valid;
 static int eeprom_version;

 #define get_eeprom_field_int(name) ({ \
 	int value; \
 	int idx; \
 	value = 0; \
 	for (idx = 0; idx < sizeof(name); idx++) { \
 		value <<= 8; \
 		value |= name[idx]; \
 	} \
 	value; \
 })

 static int read_eeprom(void)
 {
 	int eeprom_datalen;
 	int ret;

 	if (eeprom_was_read)
 		return 0;

 	eeprom_is_valid = 0;
 	ret = i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0,
 			CONFIG_SYS_I2C_EEPROM_ADDR_LEN,
 			(uchar *)&eeprom_content, sizeof(eeprom_content));
 	if (eeprom_diag) {
 		printf("DIAG: %s() read rc[%d], size[%d]\n",
 			__func__, ret, sizeof(eeprom_content));
 	}

 	if (ret != 0)
 		return -1;

 	eeprom_was_read = 1;

 	/*
 	 * check validity of EEPROM content
 	 * (check version, length, optionally checksum)
 	 */
 	eeprom_is_valid = 1;
 	eeprom_datalen = get_eeprom_field_int(eeprom_content.len);
 	eeprom_version = get_eeprom_field_int(eeprom_content.version);

 	if (eeprom_diag) {
 		printf("DIAG: %s() magic[%c%c%c] len[%d] ver[%d] type[%d]\n",
 			__func__, eeprom_content.magic[0],
 			eeprom_content.magic[1], eeprom_content.magic[2],
 			eeprom_datalen, eeprom_version, eeprom_content.type);
 	}
 	if (strncmp(eeprom_content.magic, "ifm", strlen("ifm")) != 0)
 		eeprom_is_valid = 0;
 	if (eeprom_datalen < sizeof(struct eeprom_layout) - 5)
 		eeprom_is_valid = 0;
 	if ((eeprom_version != 1) && (eeprom_version != 2))
 		eeprom_is_valid = 0;
 	if (eeprom_content.type != HW_COMP_MAINCPU)
 		eeprom_is_valid = 0;

 	if (eeprom_diag)
 		printf("DIAG: %s() valid[%d]\n", __func__, eeprom_is_valid);

 	return ret;
 }

 int mac_read_from_eeprom(void)
 {
 	const u8 *mac;
 	const char *mac_txt;

 	if (read_eeprom()) {
 		printf("I2C EEPROM read failed.\n");
 		return -1;
 	}

 	if (!eeprom_is_valid) {
 		printf("I2C EEPROM content not valid\n");
 		return -1;
 	}

 	mac = NULL;
 	switch (eeprom_version) {
 	case 1:
 	case 2:
 		mac = (const u8 *)&eeprom_content.macaddress;
 		break;
 	}

 	if (mac && is_valid_ether_addr(mac)) {
 		eth_setenv_enetaddr("ethaddr", mac);
 		if (mac_diag) {
 			mac_txt = getenv("ethaddr");
 			if (mac_txt)
 				printf("DIAG: MAC value [%s]\n", mac_txt);
 			else
 				printf("DIAG: failed to setup MAC env\n");
 		}
 	}

 	return 0;
 }

 /*
  * BEWARE!
  * this board uses DDR1(!) Micron SDRAM, *NOT* the DDR2
  * which the ADS, Aria or PDM360NG boards are using
  * (the steps outlined here refer to the Micron datasheet)
  */
 u32 sdram_init_seq[] = {
 	/* item 6, at least one NOP after CKE went high */
 	CONFIG_SYS_DDRCMD_NOP,
 	CONFIG_SYS_DDRCMD_NOP,
 	CONFIG_SYS_DDRCMD_NOP,
 	CONFIG_SYS_DDRCMD_NOP,
 	CONFIG_SYS_DDRCMD_NOP,
 	CONFIG_SYS_DDRCMD_NOP,
 	CONFIG_SYS_DDRCMD_NOP,
 	CONFIG_SYS_DDRCMD_NOP,
 	CONFIG_SYS_DDRCMD_NOP,
 	CONFIG_SYS_DDRCMD_NOP,
 	/* item 7, precharge all; item 8, tRP (20ns) */
 	CONFIG_SYS_DDRCMD_PCHG_ALL,
 	CONFIG_SYS_DDRCMD_NOP,
 	/* item 9, extended mode register; item 10, tMRD 10ns) */
 	CONFIG_SYS_MICRON_EMODE | CONFIG_SYS_MICRON_EMODE_PARAM,
 	CONFIG_SYS_DDRCMD_NOP,
 	/*
 	 * item 11, (base) mode register _with_ reset DLL;
 	 * item 12, tMRD (10ns)
 	 */
 	CONFIG_SYS_MICRON_BMODE | CONFIG_SYS_MICRON_BMODE_RSTDLL |
 	CONFIG_SYS_MICRON_BMODE_PARAM,
 	CONFIG_SYS_DDRCMD_NOP,
 	/* item 13, precharge all; item 14, tRP (20ns) */
 	CONFIG_SYS_DDRCMD_PCHG_ALL,
 	CONFIG_SYS_DDRCMD_NOP,
 	/*
 	 * item 15, auto refresh (i.e. refresh with CKE held high);
 	 * item 16, tRFC (70ns)
 	 */
 	CONFIG_SYS_DDRCMD_RFSH,
 	CONFIG_SYS_DDRCMD_NOP,
 	CONFIG_SYS_DDRCMD_NOP,
 	CONFIG_SYS_DDRCMD_NOP,
 	CONFIG_SYS_DDRCMD_NOP,
 	CONFIG_SYS_DDRCMD_NOP,
 	CONFIG_SYS_DDRCMD_NOP,
 	CONFIG_SYS_DDRCMD_NOP,
 	CONFIG_SYS_DDRCMD_NOP,
 	/*
 	 * item 17, auto refresh (i.e. refresh with CKE held high);
 	 * item 18, tRFC (70ns)
 	 */
 	CONFIG_SYS_DDRCMD_RFSH,
 	CONFIG_SYS_DDRCMD_NOP,
 	CONFIG_SYS_DDRCMD_NOP,
 	CONFIG_SYS_DDRCMD_NOP,
 	CONFIG_SYS_DDRCMD_NOP,
 	CONFIG_SYS_DDRCMD_NOP,
 	CONFIG_SYS_DDRCMD_NOP,
 	CONFIG_SYS_DDRCMD_NOP,
 	CONFIG_SYS_DDRCMD_NOP,
 	/* item 19, optional, unassert DLL reset; item 20, tMRD (20ns) */
 	CONFIG_SYS_MICRON_BMODE | CONFIG_SYS_MICRON_BMODE_PARAM,
 	CONFIG_SYS_DDRCMD_NOP,
 	/*
 	 * item 21, "actually done", but make sure 200 DRAM clock cycles
 	 * have passed after DLL reset before READ requests are issued
 	 * (200 cycles at 160MHz -> 1.25 usec)
 	 */
 	/* EMPTY, optional, we don't do it */
 };

 phys_size_t initdram(int board_type)
 {
 	return fixed_sdram(NULL, sdram_init_seq, ARRAY_SIZE(sdram_init_seq));
 }

 int misc_init_r(void)
 {
 	u32 keys;
 	char *s;
 	int want_recovery;

 	/* we use bus I2C-0 for the on-board eeprom */
 	i2c_set_bus_num(0);

 	/* setup GPIO directions and initial values */
 	gpio_configure();

 	/*
 	 * enforce the start of the recovery system when
 	 * - the appropriate keys were pressed
 	 * - "some" external software told us to
 	 * - a previous installation was aborted or has failed
 	 */
 	want_recovery = 0;
 	keys = gpio_querykbd();
 	if (gpio_diag)
 		printf("GPIO keyboard status [0x%02X]\n", keys);
 	if ((keys & GPIOKEY_BITS_RECOVERY) == GPIOKEY_BITS_RECOVERY) {
 		printf("detected recovery request (keyboard)\n");
 		want_recovery = 1;
 	}
 	s = getenv("want_recovery");
 	if ((s != NULL) && (*s != '\0')) {
 		printf("detected recovery request (environment)\n");
 		want_recovery = 1;
 	}
 	s = getenv("install_in_progress");
 	if ((s != NULL) && (*s != '\0')) {
 		printf("previous installation has not completed\n");
 		want_recovery = 1;
 	}
 	s = getenv("install_failed");
 	if ((s != NULL) && (*s != '\0')) {
 		printf("previous installation has failed\n");
 		want_recovery = 1;
 	}
 	if (want_recovery) {
 		printf("enforced start of the recovery system\n");
 		setenv("bootcmd", "run recovery");
 	}

 	/*
 	 * boot the recovery system without waiting; boot the
 	 * production system without waiting by default, only
 	 * insert a pause (to provide a chance to get a prompt)
 	 * when GPIO keys were pressed during power on
 	 */
 	if (want_recovery)
 		setenv("bootdelay", "0");
 	else if (!keys)
 		setenv("bootdelay", "0");
 	else
 		setenv("bootdelay", "2");

 	/* get the ethernet MAC from I2C EEPROM */
 	mac_read_from_eeprom();

 	return 0;
 }

 /* setup specific IO pad configuration */
 static  iopin_t ioregs_init[] = {
 	{	/* LPC CS3 */
 		offsetof(struct ioctrl512x, io_control_nfc_ce0), 1,
 		IO_PIN_OVER_FMUX | IO_PIN_OVER_DRVSTR,
 		IO_PIN_FMUX(1) | IO_PIN_DS(2),
 	},
 	{	/* LPC CS1 */
 		offsetof(struct ioctrl512x, io_control_lpc_cs1), 1,
 		IO_PIN_OVER_DRVSTR,
 		IO_PIN_DS(2),
 	},
 	{	/* LPC CS2 */
 		offsetof(struct ioctrl512x, io_control_lpc_cs2), 1,
 		IO_PIN_OVER_DRVSTR,
 		IO_PIN_DS(2),
 	},
 	{	/* LPC CS4, CS5 */
 		offsetof(struct ioctrl512x, io_control_pata_ce1), 2,
 		IO_PIN_OVER_FMUX | IO_PIN_OVER_DRVSTR,
 		IO_PIN_FMUX(1) | IO_PIN_DS(2),
 	},
 	{	/* SDHC CLK, CMD, D0, D1, D2, D3 */
 		offsetof(struct ioctrl512x, io_control_pata_ior), 6,
 		IO_PIN_OVER_FMUX | IO_PIN_OVER_DRVSTR,
 		IO_PIN_FMUX(1) | IO_PIN_DS(2),
 	},
 	{	/* GPIO keyboard */
 		offsetof(struct ioctrl512x, io_control_pci_ad30), 4,
 		IO_PIN_OVER_FMUX,
 		IO_PIN_FMUX(3),
 	},
 	{	/* GPIO DN1 PF, LCD power, DN2 PF */
 		offsetof(struct ioctrl512x, io_control_pci_ad26), 3,
 		IO_PIN_OVER_FMUX,
 		IO_PIN_FMUX(3),
 	},
 	{	/* GPIO reset AS-i */
 		offsetof(struct ioctrl512x, io_control_pci_ad21), 1,
 		IO_PIN_OVER_FMUX,
 		IO_PIN_FMUX(3),
 	},
 	{	/* GPIO reset safety */
 		offsetof(struct ioctrl512x, io_control_pci_ad19), 1,
 		IO_PIN_OVER_FMUX,
 		IO_PIN_FMUX(3),
 	},
 	{	/* GPIO reset netX */
 		offsetof(struct ioctrl512x, io_control_pci_ad16), 1,
 		IO_PIN_OVER_FMUX,
 		IO_PIN_FMUX(3),
 	},
 	{	/* GPIO ma2 en */
 		offsetof(struct ioctrl512x, io_control_pci_ad15), 1,
 		IO_PIN_OVER_FMUX,
 		IO_PIN_FMUX(3),
 	},
 	{	/* GPIO SD CD, SD WP */
 		offsetof(struct ioctrl512x, io_control_pci_ad08), 2,
 		IO_PIN_OVER_FMUX,
 		IO_PIN_FMUX(3),
 	},
 	{	/* FEC RX DV */
 		offsetof(struct ioctrl512x, io_control_pci_ad06), 1,
 		IO_PIN_OVER_FMUX | IO_PIN_OVER_DRVSTR,
 		IO_PIN_FMUX(2) | IO_PIN_DS(2),
 	},
 	{	/* GPIO AS-i prog, AS-i done, LCD backlight */
 		offsetof(struct ioctrl512x, io_control_pci_ad05), 3,
 		IO_PIN_OVER_FMUX,
 		IO_PIN_FMUX(3),
 	},
 	{	/* GPIO AS-i wdg */
 		offsetof(struct ioctrl512x, io_control_pci_req2), 1,
 		IO_PIN_OVER_FMUX,
 		IO_PIN_FMUX(3),
 	},
 	{	/* GPIO safety wdg */
 		offsetof(struct ioctrl512x, io_control_pci_req1), 1,
 		IO_PIN_OVER_FMUX,
 		IO_PIN_FMUX(3),
 	},
 	{	/* GPIO netX wdg */
 		offsetof(struct ioctrl512x, io_control_pci_req0), 1,
 		IO_PIN_OVER_FMUX,
 		IO_PIN_FMUX(3),
 	},
 	{	/* GPIO IRQ powerfail */
 		offsetof(struct ioctrl512x, io_control_pci_inta), 1,
 		IO_PIN_OVER_FMUX,
 		IO_PIN_FMUX(3),
 	},
 	{	/* GPIO AS-i PWRD */
 		offsetof(struct ioctrl512x, io_control_pci_frame), 1,
 		IO_PIN_OVER_FMUX,
 		IO_PIN_FMUX(3),
 	},
 	{	/* GPIO LED0, LED1 */
 		offsetof(struct ioctrl512x, io_control_pci_idsel), 2,
 		IO_PIN_OVER_FMUX,
 		IO_PIN_FMUX(3),
 	},
 	{	/* GPIO IRQ AS-i 1, IRQ AS-i 2, IRQ safety */
 		offsetof(struct ioctrl512x, io_control_pci_irdy), 3,
 		IO_PIN_OVER_FMUX,
 		IO_PIN_FMUX(3),
 	},
 	{	/* DIU clk */
 		offsetof(struct ioctrl512x, io_control_spdif_txclk), 1,
 		IO_PIN_OVER_FMUX | IO_PIN_OVER_DRVSTR,
 		IO_PIN_FMUX(2) | IO_PIN_DS(2),
 	},
 	{	/* FEC TX ER, CRS */
 		offsetof(struct ioctrl512x, io_control_spdif_tx), 2,
 		IO_PIN_OVER_FMUX | IO_PIN_OVER_DRVSTR,
 		IO_PIN_FMUX(1) | IO_PIN_DS(2),
 	},
 	{	/* GPIO/GPT */ /* to *NOT* have the EXT IRQ0 float */
 		offsetof(struct ioctrl512x, io_control_irq0), 1,
 		IO_PIN_OVER_FMUX,
 		IO_PIN_FMUX(3),
 	},
 	{	/*
 		 * FEC col, tx en, tx clk, txd 0-3, mdc, rx er,
 		 * rdx 3-0, mdio, rx clk
 		 */
 		offsetof(struct ioctrl512x, io_control_psc0_0), 15,
 		IO_PIN_OVER_FMUX | IO_PIN_OVER_DRVSTR,
 		IO_PIN_FMUX(1) | IO_PIN_DS(2),
 	},
 	/* optional: make sure PSC3 remains the serial console */
 	{	/* LPC CS6 */
 		offsetof(struct ioctrl512x, io_control_psc3_4), 1,
 		IO_PIN_OVER_FMUX | IO_PIN_OVER_DRVSTR,
 		IO_PIN_FMUX(1) | IO_PIN_DS(2),
 	},
 	/* make sure PSC4 remains available for SPI,
 	    *BUT* PSC4_1 is a GPIO kind of SS! */
 	{	/* enforce drive strength on the SPI pin */
 		offsetof(struct ioctrl512x, io_control_psc4_0), 5,
 		IO_PIN_OVER_DRVSTR,
 		IO_PIN_DS(2),
 	},
 	{
 		offsetof(struct ioctrl512x, io_control_psc4_1), 1,
 		IO_PIN_OVER_FMUX,
 		IO_PIN_FMUX(3),
 	},
 	/* optional: make sure PSC5 remains available for SPI */
 	{	/* enforce drive strength on the SPI pin */
 		offsetof(struct ioctrl512x, io_control_psc5_0), 5,
 		IO_PIN_OVER_DRVSTR,
 		IO_PIN_DS(1),
 	},
 	{	/* LPC TSIZ1 */
 		offsetof(struct ioctrl512x, io_control_psc6_0), 1,
 		IO_PIN_OVER_FMUX | IO_PIN_OVER_DRVSTR,
 		IO_PIN_FMUX(1) | IO_PIN_DS(2),
 	},
 	{	/* DIU hsync */
 		offsetof(struct ioctrl512x, io_control_psc6_1), 1,
 		IO_PIN_OVER_FMUX | IO_PIN_OVER_DRVSTR,
 		IO_PIN_FMUX(2) | IO_PIN_DS(1),
 	},
 	{	/* DIU vsync */
 		offsetof(struct ioctrl512x, io_control_psc6_4), 1,
 		IO_PIN_OVER_FMUX | IO_PIN_OVER_DRVSTR,
 		IO_PIN_FMUX(2) | IO_PIN_DS(1),
 	},
 	{	/* PSC7, part of DIU RGB */
 		offsetof(struct ioctrl512x, io_control_psc7_0), 2,
 		IO_PIN_OVER_FMUX | IO_PIN_OVER_DRVSTR,
 		IO_PIN_FMUX(2) | IO_PIN_DS(1),
 	},
 	{	/* PSC7, safety UART */
 		offsetof(struct ioctrl512x, io_control_psc7_2), 2,
 		IO_PIN_OVER_FMUX | IO_PIN_OVER_DRVSTR,
 		IO_PIN_FMUX(0) | IO_PIN_DS(1),
 	},
 	{	/* DIU (part of) RGB[] */
 		offsetof(struct ioctrl512x, io_control_psc8_3), 16,
 		IO_PIN_OVER_FMUX | IO_PIN_OVER_DRVSTR,
 		IO_PIN_FMUX(2) | IO_PIN_DS(1),
 	},
 	{	/* DIU data enable */
 		offsetof(struct ioctrl512x, io_control_psc11_4), 1,
 		IO_PIN_OVER_FMUX | IO_PIN_OVER_DRVSTR,
 		IO_PIN_FMUX(2) | IO_PIN_DS(1),
 	},
 	/* reduce LPB drive strength for improved EMI */
 	{	/* LPC OE, LPC RW */
 		offsetof(struct ioctrl512x, io_control_lpc_oe), 2,
 		IO_PIN_OVER_DRVSTR,
 		IO_PIN_DS(2),
 	},
 	{	/* LPC AX03 through LPC AD00 */
 		offsetof(struct ioctrl512x, io_control_lpc_ax03), 36,
 		IO_PIN_OVER_DRVSTR,
 		IO_PIN_DS(2),
 	},
 	{	/* LPC CS5 */
 		offsetof(struct ioctrl512x, io_control_pata_ce2), 1,
 		IO_PIN_OVER_DRVSTR,
 		IO_PIN_DS(2),
 	},
 	{	/* SDHC CLK */
 		offsetof(struct ioctrl512x, io_control_nfc_wp), 1,
 		IO_PIN_OVER_DRVSTR,
 		IO_PIN_DS(2),
 	},
 	{	/* SDHC DATA */
 		offsetof(struct ioctrl512x, io_control_nfc_ale), 4,
 		IO_PIN_OVER_DRVSTR,
 		IO_PIN_DS(2),
 	},
 };

 int checkboard(void)
 {
 	puts("Board: ifm AC14xx\n");

 	/* initialize function mux & slew rate IO inter alia on IO Pins  */
 	iopin_initialize_bits(ioregs_init, ARRAY_SIZE(ioregs_init));

 	return 0;
 }

 #if defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP)
 void ft_board_setup(void *blob, bd_t *bd)
 {
 	ft_cpu_setup(blob, bd);
 }
 #endif /* defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP) */
	/*
	* (C) Copyright 2009 Wolfgang Denk <wd@denx.de>
	* (C) Copyright 2009 Dave Srl www.dave.eu
	* (C) Copyright 2010 ifm ecomatic GmbH
	*
	* SPDX-License-Identifier: GPL-2.0+
	*/

	#include <common.h>
	#include <asm/bitops.h>
	#include <command.h>
	#include <asm/io.h>
	#include <asm/processor.h>
	#include <asm/mpc512x.h>
	#include <fdt_support.h>
	#ifdef CONFIG_MISC_INIT_R
	#include <i2c.h>
	#endif

	static int eeprom_diag;
	static int mac_diag;
	static int gpio_diag;

	DECLARE_GLOBAL_DATA_PTR;

	static void gpio_configure(void)
	{
	immap_t *im;
	gpio512x_t *gpioregs;

	im = (immap_t *) CONFIG_SYS_IMMR;
	gpioregs = &im->gpio;
	out_be32(&gpioregs->gpodr, 0x00290000); /* open drain */
	out_be32(&gpioregs->gpdat, 0x80001040); /* data (when output) */

	/*
	* out_be32(&gpioregs->gpdir, 0xC2293020);
	* workaround for a hardware effect: configure direction in pieces,
	* setting all outputs at once drops the reset line too low and
	* makes us lose the MII connection (breaks ethernet for us)
	*/
	out_be32(&gpioregs->gpdir, 0x02003060); /* direction */
	setbits_be32(&gpioregs->gpdir, 0x00200000); /* += reset asi */
	udelay(10);
	setbits_be32(&gpioregs->gpdir, 0x00080000); /* += reset safety */
	udelay(10);
	setbits_be32(&gpioregs->gpdir, 0x00010000); /* += reset comm */
	udelay(10);
	setbits_be32(&gpioregs->gpdir, 0xC0000000); /* += backlight, KB sel */

	/* to turn from red to yellow when U-Boot runs */
	setbits_be32(&gpioregs->gpdat, 0x00002020);
	out_be32(&gpioregs->gpimr, 0x00000000); /* interrupt mask */
	out_be32(&gpioregs->gpicr1, 0x00000004); /* interrupt sense part 1 */
	out_be32(&gpioregs->gpicr2, 0x00A80000); /* interrupt sense part 2 */
	out_be32(&gpioregs->gpier, 0xFFFFFFFF); /* interrupt events, clear */
	}

	/* the physical location of the pins */
	#define GPIOKEY_ROW_BITMASK 0x40000000
	#define GPIOKEY_ROW_UPPER 0
	#define GPIOKEY_ROW_LOWER 1

	#define GPIOKEY_COL0_BITMASK 0x20000000
	#define GPIOKEY_COL1_BITMASK 0x10000000
	#define GPIOKEY_COL2_BITMASK 0x08000000

	/* the logical presentation of pressed keys */
	#define GPIOKEY_BIT_FNLEFT (1 << 5)
	#define GPIOKEY_BIT_FNRIGHT (1 << 4)
	#define GPIOKEY_BIT_DIRUP (1 << 3)
	#define GPIOKEY_BIT_DIRLEFT (1 << 2)
	#define GPIOKEY_BIT_DIRRIGHT (1 << 1)
	#define GPIOKEY_BIT_DIRDOWN (1 << 0)

	/* the hotkey combination which starts recovery */
	#define GPIOKEY_BITS_RECOVERY (GPIOKEY_BIT_FNLEFT \| GPIOKEY_BIT_DIRUP \| \
	GPIOKEY_BIT_DIRDOWN)

	static void gpio_selectrow(gpio512x_t *gpioregs, u32 row)
	{

	if (row)
	setbits_be32(&gpioregs->gpdat, GPIOKEY_ROW_BITMASK);
	else
	clrbits_be32(&gpioregs->gpdat, GPIOKEY_ROW_BITMASK);
	udelay(10);
	}

	static u32 gpio_querykbd(void)
	{
	immap_t *im;
	gpio512x_t *gpioregs;
	u32 keybits;
	u32 input;

	im = (immap_t *)CONFIG_SYS_IMMR;
	gpioregs = &im->gpio;
	keybits = 0;

	/* query upper row */
	gpio_selectrow(gpioregs, GPIOKEY_ROW_UPPER);
	input = in_be32(&gpioregs->gpdat);
	if ((input & GPIOKEY_COL0_BITMASK) == 0)
	keybits \|= GPIOKEY_BIT_FNLEFT;
	if ((input & GPIOKEY_COL1_BITMASK) == 0)
	keybits \|= GPIOKEY_BIT_DIRUP;
	if ((input & GPIOKEY_COL2_BITMASK) == 0)
	keybits \|= GPIOKEY_BIT_FNRIGHT;

	/* query lower row */
	gpio_selectrow(gpioregs, GPIOKEY_ROW_LOWER);
	input = in_be32(&gpioregs->gpdat);
	if ((input & GPIOKEY_COL0_BITMASK) == 0)
	keybits \|= GPIOKEY_BIT_DIRLEFT;
	if ((input & GPIOKEY_COL1_BITMASK) == 0)
	keybits \|= GPIOKEY_BIT_DIRRIGHT;
	if ((input & GPIOKEY_COL2_BITMASK) == 0)
	keybits \|= GPIOKEY_BIT_DIRDOWN;

	/* return bit pattern for keys */
	return keybits;
	}

	/* excerpt from the recovery's hw_info.h */

	struct __attribute__ ((__packed__)) eeprom_layout {
	char magic[3]; /** 'ifm' */
	u8 len[2]; /** content length without magic/len fields */
	u8 version[3]; /** structure version */
	u8 type; /** type of PCB */
	u8 reserved[0x37]; /** padding up to offset 0x40 */
	u8 macaddress[6]; /** ethernet MAC (for the mainboard) @0x40 */
	};

	#define HW_COMP_MAINCPU 2

	static struct eeprom_layout eeprom_content;
	static int eeprom_was_read; /* has_been_read */
	static int eeprom_is_valid;
	static int eeprom_version;

	#define get_eeprom_field_int(name) ({ \
	int value; \
	int idx; \
	value = 0; \
	for (idx = 0; idx < sizeof(name); idx++) { \
	value <<= 8; \
	value \|= name[idx]; \
	} \
	value; \
	})

	static int read_eeprom(void)
	{
	int eeprom_datalen;
	int ret;

	if (eeprom_was_read)
	return 0;

	eeprom_is_valid = 0;
	ret = i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0,
	CONFIG_SYS_I2C_EEPROM_ADDR_LEN,
	(uchar *)&eeprom_content, sizeof(eeprom_content));
	if (eeprom_diag) {
	printf("DIAG: %s() read rc[%d], size[%d]\n",
	__func__, ret, sizeof(eeprom_content));
	}

	if (ret != 0)
	return -1;

	eeprom_was_read = 1;

	/*
	* check validity of EEPROM content
	* (check version, length, optionally checksum)
	*/
	eeprom_is_valid = 1;
	eeprom_datalen = get_eeprom_field_int(eeprom_content.len);
	eeprom_version = get_eeprom_field_int(eeprom_content.version);

	if (eeprom_diag) {
	printf("DIAG: %s() magic[%c%c%c] len[%d] ver[%d] type[%d]\n",
	__func__, eeprom_content.magic[0],
	eeprom_content.magic[1], eeprom_content.magic[2],
	eeprom_datalen, eeprom_version, eeprom_content.type);
	}
	if (strncmp(eeprom_content.magic, "ifm", strlen("ifm")) != 0)
	eeprom_is_valid = 0;
	if (eeprom_datalen < sizeof(struct eeprom_layout) - 5)
	eeprom_is_valid = 0;
	if ((eeprom_version != 1) && (eeprom_version != 2))
	eeprom_is_valid = 0;
	if (eeprom_content.type != HW_COMP_MAINCPU)
	eeprom_is_valid = 0;

	if (eeprom_diag)
	printf("DIAG: %s() valid[%d]\n", __func__, eeprom_is_valid);

	return ret;
	}

	int mac_read_from_eeprom(void)
	{
	const u8 *mac;
	const char *mac_txt;

	if (read_eeprom()) {
	printf("I2C EEPROM read failed.\n");
	return -1;
	}

	if (!eeprom_is_valid) {
	printf("I2C EEPROM content not valid\n");
	return -1;
	}

	mac = NULL;
	switch (eeprom_version) {
	case 1:
	case 2:
	mac = (const u8 *)&eeprom_content.macaddress;
	break;
	}

	if (mac && is_valid_ether_addr(mac)) {
	eth_setenv_enetaddr("ethaddr", mac);
	if (mac_diag) {
	mac_txt = getenv("ethaddr");
	if (mac_txt)
	printf("DIAG: MAC value [%s]\n", mac_txt);
	else
	printf("DIAG: failed to setup MAC env\n");
	}
	}

	return 0;
	}

	/*
	* BEWARE!
	* this board uses DDR1(!) Micron SDRAM, NOT the DDR2
	* which the ADS, Aria or PDM360NG boards are using
	* (the steps outlined here refer to the Micron datasheet)
	*/
	u32 sdram_init_seq[] = {
	/* item 6, at least one NOP after CKE went high */
	CONFIG_SYS_DDRCMD_NOP,
	CONFIG_SYS_DDRCMD_NOP,
	CONFIG_SYS_DDRCMD_NOP,
	CONFIG_SYS_DDRCMD_NOP,
	CONFIG_SYS_DDRCMD_NOP,
	CONFIG_SYS_DDRCMD_NOP,
	CONFIG_SYS_DDRCMD_NOP,
	CONFIG_SYS_DDRCMD_NOP,
	CONFIG_SYS_DDRCMD_NOP,
	CONFIG_SYS_DDRCMD_NOP,
	/* item 7, precharge all; item 8, tRP (20ns) */
	CONFIG_SYS_DDRCMD_PCHG_ALL,
	CONFIG_SYS_DDRCMD_NOP,
	/* item 9, extended mode register; item 10, tMRD 10ns) */
	CONFIG_SYS_MICRON_EMODE \| CONFIG_SYS_MICRON_EMODE_PARAM,
	CONFIG_SYS_DDRCMD_NOP,
	/*
	* item 11, (base) mode register _with_ reset DLL;
	* item 12, tMRD (10ns)
	*/
	CONFIG_SYS_MICRON_BMODE \| CONFIG_SYS_MICRON_BMODE_RSTDLL \|
	CONFIG_SYS_MICRON_BMODE_PARAM,
	CONFIG_SYS_DDRCMD_NOP,
	/* item 13, precharge all; item 14, tRP (20ns) */
	CONFIG_SYS_DDRCMD_PCHG_ALL,
	CONFIG_SYS_DDRCMD_NOP,
	/*
	* item 15, auto refresh (i.e. refresh with CKE held high);
	* item 16, tRFC (70ns)
	*/
	CONFIG_SYS_DDRCMD_RFSH,
	CONFIG_SYS_DDRCMD_NOP,
	CONFIG_SYS_DDRCMD_NOP,
	CONFIG_SYS_DDRCMD_NOP,
	CONFIG_SYS_DDRCMD_NOP,
	CONFIG_SYS_DDRCMD_NOP,
	CONFIG_SYS_DDRCMD_NOP,
	CONFIG_SYS_DDRCMD_NOP,
	CONFIG_SYS_DDRCMD_NOP,
	/*
	* item 17, auto refresh (i.e. refresh with CKE held high);
	* item 18, tRFC (70ns)
	*/
	CONFIG_SYS_DDRCMD_RFSH,
	CONFIG_SYS_DDRCMD_NOP,
	CONFIG_SYS_DDRCMD_NOP,
	CONFIG_SYS_DDRCMD_NOP,
	CONFIG_SYS_DDRCMD_NOP,
	CONFIG_SYS_DDRCMD_NOP,
	CONFIG_SYS_DDRCMD_NOP,
	CONFIG_SYS_DDRCMD_NOP,
	CONFIG_SYS_DDRCMD_NOP,
	/* item 19, optional, unassert DLL reset; item 20, tMRD (20ns) */
	CONFIG_SYS_MICRON_BMODE \| CONFIG_SYS_MICRON_BMODE_PARAM,
	CONFIG_SYS_DDRCMD_NOP,
	/*
	* item 21, "actually done", but make sure 200 DRAM clock cycles
	* have passed after DLL reset before READ requests are issued
	* (200 cycles at 160MHz -> 1.25 usec)
	*/
	/* EMPTY, optional, we don't do it */
	};

	phys_size_t initdram(int board_type)
	{
	return fixed_sdram(NULL, sdram_init_seq, ARRAY_SIZE(sdram_init_seq));
	}

	int misc_init_r(void)
	{
	u32 keys;
	char *s;
	int want_recovery;

	/* we use bus I2C-0 for the on-board eeprom */
	i2c_set_bus_num(0);

	/* setup GPIO directions and initial values */
	gpio_configure();

	/*
	* enforce the start of the recovery system when
	* - the appropriate keys were pressed
	* - "some" external software told us to
	* - a previous installation was aborted or has failed
	*/
	want_recovery = 0;
	keys = gpio_querykbd();
	if (gpio_diag)
	printf("GPIO keyboard status [0x%02X]\n", keys);
	if ((keys & GPIOKEY_BITS_RECOVERY) == GPIOKEY_BITS_RECOVERY) {
	printf("detected recovery request (keyboard)\n");
	want_recovery = 1;
	}
	s = getenv("want_recovery");
	if ((s != NULL) && (*s != '\0')) {
	printf("detected recovery request (environment)\n");
	want_recovery = 1;
	}
	s = getenv("install_in_progress");
	if ((s != NULL) && (*s != '\0')) {
	printf("previous installation has not completed\n");
	want_recovery = 1;
	}
	s = getenv("install_failed");
	if ((s != NULL) && (*s != '\0')) {
	printf("previous installation has failed\n");
	want_recovery = 1;
	}
	if (want_recovery) {
	printf("enforced start of the recovery system\n");
	setenv("bootcmd", "run recovery");
	}

	/*
	* boot the recovery system without waiting; boot the
	* production system without waiting by default, only
	* insert a pause (to provide a chance to get a prompt)
	* when GPIO keys were pressed during power on
	*/
	if (want_recovery)
	setenv("bootdelay", "0");
	else if (!keys)
	setenv("bootdelay", "0");
	else
	setenv("bootdelay", "2");

	/* get the ethernet MAC from I2C EEPROM */
	mac_read_from_eeprom();

	return 0;
	}

	/* setup specific IO pad configuration */
	static iopin_t ioregs_init[] = {
	{ /* LPC CS3 */
	offsetof(struct ioctrl512x, io_control_nfc_ce0), 1,
	IO_PIN_OVER_FMUX \| IO_PIN_OVER_DRVSTR,
	IO_PIN_FMUX(1) \| IO_PIN_DS(2),
	},
	{ /* LPC CS1 */
	offsetof(struct ioctrl512x, io_control_lpc_cs1), 1,
	IO_PIN_OVER_DRVSTR,
	IO_PIN_DS(2),
	},
	{ /* LPC CS2 */
	offsetof(struct ioctrl512x, io_control_lpc_cs2), 1,
	IO_PIN_OVER_DRVSTR,
	IO_PIN_DS(2),
	},
	{ /* LPC CS4, CS5 */
	offsetof(struct ioctrl512x, io_control_pata_ce1), 2,
	IO_PIN_OVER_FMUX \| IO_PIN_OVER_DRVSTR,
	IO_PIN_FMUX(1) \| IO_PIN_DS(2),
	},
	{ /* SDHC CLK, CMD, D0, D1, D2, D3 */
	offsetof(struct ioctrl512x, io_control_pata_ior), 6,
	IO_PIN_OVER_FMUX \| IO_PIN_OVER_DRVSTR,
	IO_PIN_FMUX(1) \| IO_PIN_DS(2),
	},
	{ /* GPIO keyboard */
	offsetof(struct ioctrl512x, io_control_pci_ad30), 4,
	IO_PIN_OVER_FMUX,
	IO_PIN_FMUX(3),
	},
	{ /* GPIO DN1 PF, LCD power, DN2 PF */
	offsetof(struct ioctrl512x, io_control_pci_ad26), 3,
	IO_PIN_OVER_FMUX,
	IO_PIN_FMUX(3),
	},
	{ /* GPIO reset AS-i */
	offsetof(struct ioctrl512x, io_control_pci_ad21), 1,
	IO_PIN_OVER_FMUX,
	IO_PIN_FMUX(3),
	},
	{ /* GPIO reset safety */
	offsetof(struct ioctrl512x, io_control_pci_ad19), 1,
	IO_PIN_OVER_FMUX,
	IO_PIN_FMUX(3),
	},
	{ /* GPIO reset netX */
	offsetof(struct ioctrl512x, io_control_pci_ad16), 1,
	IO_PIN_OVER_FMUX,
	IO_PIN_FMUX(3),
	},
	{ /* GPIO ma2 en */
	offsetof(struct ioctrl512x, io_control_pci_ad15), 1,
	IO_PIN_OVER_FMUX,
	IO_PIN_FMUX(3),
	},
	{ /* GPIO SD CD, SD WP */
	offsetof(struct ioctrl512x, io_control_pci_ad08), 2,
	IO_PIN_OVER_FMUX,
	IO_PIN_FMUX(3),
	},
	{ /* FEC RX DV */
	offsetof(struct ioctrl512x, io_control_pci_ad06), 1,
	IO_PIN_OVER_FMUX \| IO_PIN_OVER_DRVSTR,
	IO_PIN_FMUX(2) \| IO_PIN_DS(2),
	},
	{ /* GPIO AS-i prog, AS-i done, LCD backlight */
	offsetof(struct ioctrl512x, io_control_pci_ad05), 3,
	IO_PIN_OVER_FMUX,
	IO_PIN_FMUX(3),
	},
	{ /* GPIO AS-i wdg */
	offsetof(struct ioctrl512x, io_control_pci_req2), 1,
	IO_PIN_OVER_FMUX,
	IO_PIN_FMUX(3),
	},
	{ /* GPIO safety wdg */
	offsetof(struct ioctrl512x, io_control_pci_req1), 1,
	IO_PIN_OVER_FMUX,
	IO_PIN_FMUX(3),
	},
	{ /* GPIO netX wdg */
	offsetof(struct ioctrl512x, io_control_pci_req0), 1,
	IO_PIN_OVER_FMUX,
	IO_PIN_FMUX(3),
	},
	{ /* GPIO IRQ powerfail */
	offsetof(struct ioctrl512x, io_control_pci_inta), 1,
	IO_PIN_OVER_FMUX,
	IO_PIN_FMUX(3),
	},
	{ /* GPIO AS-i PWRD */
	offsetof(struct ioctrl512x, io_control_pci_frame), 1,
	IO_PIN_OVER_FMUX,
	IO_PIN_FMUX(3),
	},
	{ /* GPIO LED0, LED1 */
	offsetof(struct ioctrl512x, io_control_pci_idsel), 2,
	IO_PIN_OVER_FMUX,
	IO_PIN_FMUX(3),
	},
	{ /* GPIO IRQ AS-i 1, IRQ AS-i 2, IRQ safety */
	offsetof(struct ioctrl512x, io_control_pci_irdy), 3,
	IO_PIN_OVER_FMUX,
	IO_PIN_FMUX(3),
	},
	{ /* DIU clk */
	offsetof(struct ioctrl512x, io_control_spdif_txclk), 1,
	IO_PIN_OVER_FMUX \| IO_PIN_OVER_DRVSTR,
	IO_PIN_FMUX(2) \| IO_PIN_DS(2),
	},
	{ /* FEC TX ER, CRS */
	offsetof(struct ioctrl512x, io_control_spdif_tx), 2,
	IO_PIN_OVER_FMUX \| IO_PIN_OVER_DRVSTR,
	IO_PIN_FMUX(1) \| IO_PIN_DS(2),
	},
	{ /* GPIO/GPT / / to NOT have the EXT IRQ0 float */
	offsetof(struct ioctrl512x, io_control_irq0), 1,
	IO_PIN_OVER_FMUX,
	IO_PIN_FMUX(3),
	},
	{ /*
	* FEC col, tx en, tx clk, txd 0-3, mdc, rx er,
	* rdx 3-0, mdio, rx clk
	*/
	offsetof(struct ioctrl512x, io_control_psc0_0), 15,
	IO_PIN_OVER_FMUX \| IO_PIN_OVER_DRVSTR,
	IO_PIN_FMUX(1) \| IO_PIN_DS(2),
	},
	/* optional: make sure PSC3 remains the serial console */
	{ /* LPC CS6 */
	offsetof(struct ioctrl512x, io_control_psc3_4), 1,
	IO_PIN_OVER_FMUX \| IO_PIN_OVER_DRVSTR,
	IO_PIN_FMUX(1) \| IO_PIN_DS(2),
	},
	/* make sure PSC4 remains available for SPI,
	BUT PSC4_1 is a GPIO kind of SS! */
	{ /* enforce drive strength on the SPI pin */
	offsetof(struct ioctrl512x, io_control_psc4_0), 5,
	IO_PIN_OVER_DRVSTR,
	IO_PIN_DS(2),
	},
	{
	offsetof(struct ioctrl512x, io_control_psc4_1), 1,
	IO_PIN_OVER_FMUX,
	IO_PIN_FMUX(3),
	},
	/* optional: make sure PSC5 remains available for SPI */
	{ /* enforce drive strength on the SPI pin */
	offsetof(struct ioctrl512x, io_control_psc5_0), 5,
	IO_PIN_OVER_DRVSTR,
	IO_PIN_DS(1),
	},
	{ /* LPC TSIZ1 */
	offsetof(struct ioctrl512x, io_control_psc6_0), 1,
	IO_PIN_OVER_FMUX \| IO_PIN_OVER_DRVSTR,
	IO_PIN_FMUX(1) \| IO_PIN_DS(2),
	},
	{ /* DIU hsync */
	offsetof(struct ioctrl512x, io_control_psc6_1), 1,
	IO_PIN_OVER_FMUX \| IO_PIN_OVER_DRVSTR,
	IO_PIN_FMUX(2) \| IO_PIN_DS(1),
	},
	{ /* DIU vsync */
	offsetof(struct ioctrl512x, io_control_psc6_4), 1,
	IO_PIN_OVER_FMUX \| IO_PIN_OVER_DRVSTR,
	IO_PIN_FMUX(2) \| IO_PIN_DS(1),
	},
	{ /* PSC7, part of DIU RGB */
	offsetof(struct ioctrl512x, io_control_psc7_0), 2,
	IO_PIN_OVER_FMUX \| IO_PIN_OVER_DRVSTR,
	IO_PIN_FMUX(2) \| IO_PIN_DS(1),
	},
	{ /* PSC7, safety UART */
	offsetof(struct ioctrl512x, io_control_psc7_2), 2,
	IO_PIN_OVER_FMUX \| IO_PIN_OVER_DRVSTR,
	IO_PIN_FMUX(0) \| IO_PIN_DS(1),
	},
	{ /* DIU (part of) RGB[] */
	offsetof(struct ioctrl512x, io_control_psc8_3), 16,
	IO_PIN_OVER_FMUX \| IO_PIN_OVER_DRVSTR,
	IO_PIN_FMUX(2) \| IO_PIN_DS(1),
	},
	{ /* DIU data enable */
	offsetof(struct ioctrl512x, io_control_psc11_4), 1,
	IO_PIN_OVER_FMUX \| IO_PIN_OVER_DRVSTR,
	IO_PIN_FMUX(2) \| IO_PIN_DS(1),
	},
	/* reduce LPB drive strength for improved EMI */
	{ /* LPC OE, LPC RW */
	offsetof(struct ioctrl512x, io_control_lpc_oe), 2,
	IO_PIN_OVER_DRVSTR,
	IO_PIN_DS(2),
	},
	{ /* LPC AX03 through LPC AD00 */
	offsetof(struct ioctrl512x, io_control_lpc_ax03), 36,
	IO_PIN_OVER_DRVSTR,
	IO_PIN_DS(2),
	},
	{ /* LPC CS5 */
	offsetof(struct ioctrl512x, io_control_pata_ce2), 1,
	IO_PIN_OVER_DRVSTR,
	IO_PIN_DS(2),
	},
	{ /* SDHC CLK */
	offsetof(struct ioctrl512x, io_control_nfc_wp), 1,
	IO_PIN_OVER_DRVSTR,
	IO_PIN_DS(2),
	},
	{ /* SDHC DATA */
	offsetof(struct ioctrl512x, io_control_nfc_ale), 4,
	IO_PIN_OVER_DRVSTR,
	IO_PIN_DS(2),
	},
	};

	int checkboard(void)
	{
	puts("Board: ifm AC14xx\n");

	/* initialize function mux & slew rate IO inter alia on IO Pins */
	iopin_initialize_bits(ioregs_init, ARRAY_SIZE(ioregs_init));

	return 0;
	}

	#if defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP)
	void ft_board_setup(void blob, bd_t bd)
	{
	ft_cpu_setup(blob, bd);
	}
	#endif /* defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP) */